Data reported on webserver not appearing to HA > 'Unkown'

[chrisborell]

I'm encountering an issue where data is being successfully scraped from the inverter and displayed on the webserver but isn't being forwarded to Home Assistant via MQTT. They report being 'Unknown'

• Active import from Grid
• Daily export to grid
• Daily import from grid

Address

---- | device_type_code | SG10RT vr001 | run_state | ON vr003 | last_reset | 2024-2-12 8:49:25 vr006 | daily_export_to_grid | 0.006833333333333333 kWh vr007 | daily_import_from_grid | 0.16488055555555547 kWh 5001 | nominal_active_power | 10.0 kW 5002 | output_type | 2P 5003 | daily_power_yields | 2.3 kWh 5004 | total_power_yields | 16825.3 kWh 5006 | total_running_time | 3977 h 5008 | internal_temperature | 42.1 °C 5009 | total_apparent_power | 3108 VA 5011 | mppt_1_voltage | 440.0 V 5012 | mppt_1_current | 2.4 A 5013 | mppt_2_voltage | 394.9 V 5014 | mppt_2_current | 3.5 A 5017 | total_dc_power | 3334 W 5019 | phase_a_voltage | 231.1 V 5020 | phase_b_voltage | 0.0 V 5021 | phase_c_voltage | 0.0 V 5022 | phase_a_current | 13.4 A 5023 | phase_b_current | 0.0 A 5024 | phase_c_current | 0.0 A 5031 | total_active_power | 3108 W 5033 | total_reactive_power | -4 Var 5035 | power_factor | 1.0 5036 | grid_frequency | 49.99 Hz 5038 | work_state_1 | Dispatch Run 5049 | nominal_reactive_power | 6.0 kVar 5071 | array_insulation_resistance | 1556 k-ohm 5077 | active_power_regulation_setpoint | 10000 W 5079 | reactive_power_regulation_setpoint | 0 Var 5081 | work_state_2 | Run 5083 | meter_power | -360 W 5091 | load_power | 2748 W 5113 | daily_running_time | 126 min 5128 | monthly_power_yields | 670.8 kWh 5146 | negative_voltage_to_the_ground | 0.0 V 5147 | bus_voltage | 465.5 V 5150 | pid_work_state | None 5151 | pid_alarm_code | None 5216 | export_power | -328 W 5218 | power_meter | 2737 W 7013 | string_1_current | 0.0 A 7014 | string_2_current | 0.0 A 7015 | string_3_current | 0.0 A 5006 | start_stop | Start 5007 | power_limitation_switch | Enable 5008 | power_limitation_setting | 100.0 % 5019 | power_factor_setting | 0.0 5035 | night_svg_switch | Disable 5036 | reactive_power_adjustment_mode | Off 5037 | reactive_power_percentage_setting | 0.0 % 5039 | power_limitation_adjustment | 10.0 kW 5040 | reactive_power_adjustment | 0.0 kVar 5041 | pid_recovery | Disable vr002 | timestamp | 2024-2-12 9:05:05 vr004 | export_to_grid | 360 W vr005 | import_from_grid | 0 W

[swordfish6975]

@chrisborell same issue this is what fixed it for me, ssh to your home assistant server.

ha core update --version 2024.1.5

It will take a while and downgrade your HA.

Think something broke in core version 2024.1.6+ or perhaps there is now a incompatibility with SunGather and the new core versions.

When it prompts you to update to any new version just skip for now.

[swordfish6975]

Alternatively it could be something to do with this here.

perhaps these two need to be just total (not total_increasing) now in the config files?

can someone on 2024.2.X verify?

[bohdan-s]

Yes. There have been some breaking changes I need to address. Sorry

[swordfish6975]

All good, let me know if I can help any any way 🙂

[swordfish6975]

I have updated back to the latest HA Core 2024.2.1 and commented out the following two lines from my config.yaml

last_reset_value_template: "{{ value_json.last_reset }}"

(note: its there twice, once for daily_import_from_grid and once for daily_export_to_grid)

After a reboot it seems to be working again, I will monitor for adverse affects and report back in a few days.

[weichenw]

I have changed the 'state_class' to 'total'. Seems to be running fine now. Currently on 2024.2.1

[swordfish6975]

Removing the "last_reset_value_template" seems to have caused no adverse affects for me 👍

@weichenw interested as to what the outcome was leaving it there and making it state_class:total?

[weichenw]

Removing the "last_reset_value_template" seems to have caused no adverse affects for me 👍

@weichenw interested as to what the outcome was leaving it there and making it state_class:total?

It seems to work for me as per normal.

[skye-harris]

Much thanks to you both, @weichenw @swordfish6975

I have used the same solution here as provided by @swordfish6975 and this also seems to have worked without issue (touch wood) :)

[patrikbloemer]

I have updated back to the latest HA Core 2024.2.1 and commented out the following two lines from my config.yaml

last_reset_value_template: "{{ value_json.last_reset }}"

(note: its there twice, once for daily_import_from_grid and once for daily_export_to_grid)

After a reboot it seems to be working again, I will monitor for adverse affects and report back in a few days.

In what file do you edit? Where do I find it? /Patrik

[chrfritsch]

In what file do you edit? Where do I find it?

It's in /root/share/SunGather on my Raspberry