Open Sinaloense opened 9 months ago
celebraces
commented
9 months ago If you take the SIM out of the GPS tracker and put it in a phone, you may receive text messages from their provisioning system that will provide the unlock code. I suspect that wanway detect when the SIM card is first activated, and if they don't receive GPS data within a certain time period, it sends commands to update the APN/Server addresses.
Sinaloense
commented
9 months ago thanks, I have retired SIM from gps and put it on a cellphone, I will wait to see if I have luck and receive a message.
SzymonZy
commented
8 months ago Did You get messages?
Sinaloense
commented
8 months ago Did You get messages?
I didn't get any message, I still can't unlock it.
lparakhin
commented
3 months ago I got message from number 310002681 with text STATUS# when insert SIM to mobile phone
slavagalileo
commented
1 month ago Hello everyone, Forumchane! The problem with this tracker is that it is not allowed to change the server. When sending an SMS message with the server settings, the GPS tracker sends an error message. Alas, so programmed from the factory, so that only their server is used. There is a locked and unlocked tracker (which responds to sms commands). There is an idea to connect via tx rx and transfer the firmware from one to the second. On board is the rdk 8955l processor, which is sealed with a protective cover. I enclose the photo. The board has + - dp rx1 rx gnd tx tx1 off rest pwk gtx grx pins. The photo shows 2 identical devices, but one is already without a cover (unsoldered.) Interested in software and a programmer for reading firmware. I tried using usb UART and Luatools_v2 software. To no avail. p. s I connected the gnd and pwk contacts with a 1k resistor. p. p.s even more interesting are the necessary contacts for firmware. https://i.postimg.cc/hjhQC9sn/IMG-20240531-214520.jpg https://i.postimg.cc/N0sHXhr5/IMG-20240531-214530.jpg https://i.postimg.cc/vm06LPWX/IMG-20240531-214551.jpg
lparakhin
commented
1 month ago Hello everyone, Forumchane! The problem with this tracker is that it is not allowed to change the server. When sending an SMS message with the server settings, the GPS tracker sends an error message. Alas, so programmed from the factory, so that only their server is used. There is a locked and unlocked tracker (which responds to sms commands). There is an idea to connect via tx rx and transfer the firmware from one to the second. On board is the rdk 8955l processor, which is sealed with a protective cover. I enclose the photo. The board has + - dp rx1 rx gnd tx tx1 off rest pwk gtx grx pins. The photo shows 2 identical devices, but one is already without a cover (unsoldered.) Interested in software and a programmer for reading firmware. I tried using usb UART and Luatools_v2 software. To no avail. p. s I connected the gnd and pwk contacts with a 1k resistor. p. p.s even more interesting are the necessary contacts for firmware. https://i.postimg.cc/hjhQC9sn/IMG-20240531-214520.jpg https://i.postimg.cc/N0sHXhr5/IMG-20240531-214530.jpg https://i.postimg.cc/vm06LPWX/IMG-20240531-214551.jpg
Need to downgrade firmware first, when unlock commands will be available.
slavagalileo
commented
4 weeks ago Hello everyone, Forumchane! The problem with this tracker is that it is not allowed to change the server. When sending an SMS message with the server settings, the GPS tracker sends an error message. Alas, so programmed from the factory, so that only their server is used. There is a locked and unlocked tracker (which responds to sms commands). There is an idea to connect via tx rx and transfer the firmware from one to the second. On board is the rdk 8955l processor, which is sealed with a protective cover. I enclose the photo. The board has + - dp rx1 rx gnd tx tx1 off rest pwk gtx grx pins. The photo shows 2 identical devices, but one is already without a cover (unsoldered.) Interested in software and a programmer for reading firmware. I tried using usb UART and Luatools_v2 software. To no avail. p. s I connected the gnd and pwk contacts with a 1k resistor. p. p.s even more interesting are the necessary contacts for firmware. https://i.postimg.cc/hjhQC9sn/IMG-20240531-214520.jpg https://i.postimg.cc/N0sHXhr5/IMG-20240531-214530.jpg https://i.postimg.cc/vm06LPWX/IMG-20240531-214551.jpg
Need to downgrade firmware first, when unlock commands will be available.
How can I update the firmware?
lparakhin
commented
3 weeks ago Hello everyone, Forumchane! The problem with this tracker is that it is not allowed to change the server. When sending an SMS message with the server settings, the GPS tracker sends an error message. Alas, so programmed from the factory, so that only their server is used. There is a locked and unlocked tracker (which responds to sms commands). There is an idea to connect via tx rx and transfer the firmware from one to the second. On board is the rdk 8955l processor, which is sealed with a protective cover. I enclose the photo. The board has + - dp rx1 rx gnd tx tx1 off rest pwk gtx grx pins. The photo shows 2 identical devices, but one is already without a cover (unsoldered.) Interested in software and a programmer for reading firmware. I tried using usb UART and Luatools_v2 software. To no avail. p. s I connected the gnd and pwk contacts with a 1k resistor. p. p.s even more interesting are the necessary contacts for firmware. https://i.postimg.cc/hjhQC9sn/IMG-20240531-214520.jpg https://i.postimg.cc/N0sHXhr5/IMG-20240531-214530.jpg https://i.postimg.cc/vm06LPWX/IMG-20240531-214551.jpg
Need to downgrade firmware first, when unlock commands will be available.
How can I update the firmware?
Have a look here https://github.com/bohdan-s/WanWay-Tech-S20/issues/7
slavagalileo
commented
3 weeks ago Hello everyone, Forumchane! The problem with this tracker is that it is not allowed to change the server. When sending an SMS message with the server settings, the GPS tracker sends an error message. Alas, so programmed from the factory, so that only their server is used. There is a locked and unlocked tracker (which responds to sms commands). There is an idea to connect via tx rx and transfer the firmware from one to the second. On board is the rdk 8955l processor, which is sealed with a protective cover. I enclose the photo. The board has + - dp rx1 rx gnd tx tx1 off rest pwk gtx grx pins. The photo shows 2 identical devices, but one is already without a cover (unsoldered.) Interested in software and a programmer for reading firmware. I tried using usb UART and Luatools_v2 software. To no avail. p. s I connected the gnd and pwk contacts with a 1k resistor. p. p.s even more interesting are the necessary contacts for firmware. https://i.postimg.cc/hjhQC9sn/IMG-20240531-214520.jpg https://i.postimg.cc/N0sHXhr5/IMG-20240531-214530.jpg https://i.postimg.cc/vm06LPWX/IMG-20240531-214551.jpg
Need to downgrade firmware first, when unlock commands will be available.
How can I update the firmware?
Have a look here #7
The fact is that the g19 does not have a usb connector . There are only contacts listed in the photo.
slavagalileo
commented
3 weeks ago The fact is that the g19 does not have a usb connector . There are only contacts listed in the photo.
slavagalileo
commented
2 weeks ago Всем привет, Форумчане! Проблема с этим трекером заключается в том, что ему не разрешено менять сервер. При отправке SMS-сообщения с настройками сервера GPS-трекер отправляет сообщение об ошибке. Увы, так запрограммировано с завода, так что используется только их сервер. Существует заблокированный и разблокированный трекер (который реагирует на sms-команды). Есть идея подключиться через tx rx и перенести прошивку с одного на второй. На плате находится процессор rdk 8955l, который закрыт защитной крышкой. Прилагаю фотографию. Плата имеет контакты + - dp rx1 rx gnd tx tx1 off rest pwk gtx grx. На фото показаны 2 идентичных устройства, но одно уже без крышки (распаянное.) Интересуюсь программным обеспечением и программистом для чтения прошивки. Я попробовал использовать программное обеспечение usb UART и Luatools_v2. Безрезультатно. p. я соединил контакты gnd и pwk резистором 1 ком. p. p.еще более интересными являются необходимые контакты для прошивки. https://i.postimg.cc/hjhQC9sn/IMG-20240531-214520.jpg https://i.postimg.cc/N0sHXhr5/IMG-20240531-214530.jpg https://i.postimg.cc/vm06LPWX/IMG-20240531-214551.jpg
Сначала необходимо понизить версию прошивки, когда будут доступны команды разблокировки.
Как я могу обновить прошивку?
Взгляните сюда #7
I live in Crimea, the international SIM card doesn't work here
Hello and Thanks for share your knowledge.
I also have an S20, fortunately it did not come locked, but I am waiting for some more that I ordered, I hope they do not come locked and in case they do come locked I hope I can unlock them with your information.
But for now my problem is that I have a WanWay G19 (gt06 protocol) and also the SERVER command is locked, Im getting:
ERROR:The domain name or IP is locked,not allowed to modifyVERSION#
I have tried with the follow commands but Im getting
ERROR:100LOCKIP,WWDSS20,UNLOCK# LOCKIP,WWDSG19,UNLOCK# LOCKIP,WWG19,UNLOCK# LOCKIP,WWDSRDA,UNLOCK# LOCKIP,WWRDA,UNLOCK#Did you know how I could discovered the unlock command?
I read the paragraph about Celebraces but, what is a standar device? Could you help me? So I could try discovered the unlock command, thanks. G19 doesn´t have USB port.