Open 0x1234567890 opened 11 months ago
It seems they may have changed the password. can you put the original sim into a phone and see if receives any SMS? It may tell us the new password.
It seems they may have changed the password. can you put the original sim into a phone and see if receives any SMS? It may tell us the new password.
And why they should send the password via sms? How Can i unlock with the code?
Or is it possible to reflash the device?
Hi, most of this is explained in the readme. These devices come locked from the factory, when the device is turned on for the first time the unlock code is sent to set the APN correctly. We then used the same code to unlock the server/ip settings. If the code in the readme is not working, then they have changed the code. The best way to get the new code would be to try to get it the same way we got the old one, by putting the supplied SIM in a phone and check what commands are sent (as per the discovery part of the readme). As for flashing the firmware, if you can figure it out let me know :) I was able to get it into flash mode, but could not find any alternate firmware's or code to load.
Try FACTORY# instead of
I try to change the server ip but
- Request:
SERVER,0,148.251.67.210,24871,0#
- Response:
ERROR:The domain name or IP is locked,not allowed to modify.
- Request:
LOCKIP,WWDSS20,UNLOCK#
- Response:
ERROR:101
I also tryed to Factory reset with:
FACTORYALL#
after that i still not can change the IP.What can i do now?
Try FACTORY# rather than FACTORYALL# before the other commands - I believe that will fix your problem (seems to have been a change)
Hi. Not work
Hi. Not work
Mine seems to be an older version: Version: S20_4G_LA_V01_Oct 22 2022_13:49:35.
Did you try: If the code in the readme is not working, then they have changed the code. The best way to get the new code would be to try to get it the same way we got the old one, by putting the supplied SIM in a phone and check what commands are sent (as per the discovery part of the readme).
Hi, same software, same problem. I put the sim card from tracker to my phone. This simcard is set as DATA ONLY. I am not reciving any sms.
Hola, compré dos artículos la semana pasada y ambos están bloqueados para cambiar de servidor. Tampoco funciona el comando FACTORYALL# en ninguno. VERSION#: Y2517_S20_DS_1_V02_2023.05.02_1 Modelo de chip: V1.6
Tengo otro dispositivo de unos meses atrás que permite toda la configuración. Creo que los nuevos los están capando. Por ahora devolveré estos e intentaré comprarlos en otro proveedor, a ver si hay algo más antiguo disponible.
Can read sms with AT+ commands.
AT+CGMR
+CGMR: Y2517_S20_DS_1SEC_V02, 2023/05/02 17:03
OK
AT+CMGR=1
+CMGR: 2,, 72 00110000FF0008A94000B600B200BA00B600A000B600B200BA00B600AC00A900D300C700C900C800C600CB00C900CF00CA00CE00CA00C800C600CA00C900C600D300CD00CF00CC00DC
AT+CMGR=4
+CMGR: 2,, 24 00510000FF0008A9100500032A020200CD00BC00CD00BB00DC
OK
Can you explain the procedure to unlock Ip server and Apn?
i've my traccar server
thx!
On mine new s20 APN isn't locked but IP yes, don't have new password to unclock IP. This sms seems to be sent and no one are received. They don't need to send a sms with password to change APN.
ok for APN ,i need change ip server,can you help me?
No password, no party 😔
the psw is sent from default sim installed? with another s20 ,remove first sim default,install own sim,the ip server can change?
2G versión have a mt2503dv, I have dumped the rom.
i can restore the modified rom with ip server unlocked?
can you send me dumped rom and tool for restore fw unlock?
https://github.com/johnyHV/MTK2503-DOCUMENTATION/
To read need FlashTool_v5.1516.00 and scatter files from dl_src dir
Before first power on,new item, if remove the original sim and put my sim, is possible send command to change ip server?
if the original sim on first boot power on send the lock code for ip server, if change before power on the original sim, unlocked probabily is possible?
https://github.com/johnyHV/MTK2503-DOCUMENTATION/
To read need FlashTool_v5.1516.00 and scatter files from dl_src dir and a connect a usb to serial to rx tx and [ground.
To flash no idea, needed separate bootloader, rom and more partitions
Hello i have old version wanway s20. Please write how i can do dump and i will send for use it !!! thanke you
WARNING !!! CAN DAMAGE THE DEVICE
I HAVE ONE OLD S20, I WILL READ IT WHEN.......
Dont' know if old version fw can be flashed on new devices.
2G MTK mt2503dv version only. Need a usb ttl adapter (drivers installed) and solder 3 wires, Tx Rx and ground. Download latest mtk flash tool https://androidmtk.com/download-mtk-flash-tool
Open 1.cfg scatter fille DON'T FLASH!!!!!!! Go to Read Back, read start 0x00000000 length 0x00400000
Connect Rx(white wire) to Tx, Tx(green wire) to Rx and ground, connect usb ttl and check port number.
Push read back button, turn on device and wait.
Don't share here the dump, imei and configured server is on dump
WARNING !!! CAN DAMAGE THE DEVICE
I HAVE ONE OLD S20, I WILL READ IT WHEN.......
Dont' know if old version fw can be flashed on new devices.
2G MTK mt2503dv version only. Need a usb ttl adapter (drivers installed) and solder 3 wires, Tx Rx and ground. Download latest mtk flash tool https://androidmtk.com/download-mtk-flash-tool
Open 1.cfg scatter fille DON'T FLASH!!!!!!! Go to Read Back, read start 0x00000000 length 0x00400000
Connect Rx(white wire) to Tx, Tx(green wire) to Rx and ground, connect usb ttl and check port number.
Push read back button, turn on device and wait.
Don't share here the dump, imei and configured server is on dump
Ok. Thx. I will create a dump soon and send it to you. Apparently they use a spi 25Q32 flash drive, you can make a dump using any programmer! I also want to try to analyze the dump through IDA to find the password there.
WARNING !!! CAN DAMAGE THE DEVICE
I HAVE ONE OLD S20, I WILL READ IT WHEN.......
Dont' know if old version fw can be flashed on new devices.
2G MTK mt2503dv version only. Need a usb ttl adapter (drivers installed) and solder 3 wires, Tx Rx and ground. Download latest mtk flash tool https://androidmtk.com/download-mtk-flash-tool
Open 1.cfg scatter fille DON'T FLASH!!!!!!! Go to Read Back, read start 0x00000000 length 0x00400000
Connect Rx(white wire) to Tx, Tx(green wire) to Rx and ground, connect usb ttl and check port number.
Push read back button, turn on device and wait.
Don't share here the dump, imei and configured server is on dump
Pls send you mail for send dump, after download from device.
Is on my GH profile
Is on my GH profile, diegocr@gmail.com
Hello, I send to you mail, 2 dump, 1 dump from old version and 1 new version!!! and picture for analize HEX.
With nop0x900 dumps ww s20 is unlocked
Thanks nop0x900 !!!!
Was there a new password required? Or how did you unlock it?
Flashing nop0x900 dump (version Y2517_GW005A_V03_2022.10.21_17) and WWDSS20 code, still testing
Can't flash full dump, need to separate partitions and start address ans sizes
So we may have an option to flash a specific firmware version with known password?
2G version have mt2503dv, can dump and flash with mtk flashtool but need to split and modify it.
Hello
First of all which pins did you use I see no regular pinheader for serial communication on board. Only pins tx1, rx1, plenty of gnd's. Was that TX1, RX1 - gnd does not matter? I want to compare two of my boards - locked and unlocked. Could be that we can edit server directly in hex and flash again. If there is not checksum made on boot.
Can't be flashed by USB cable, don't open it
No idea why you want me to use usb? I'm looking on pcb and there is no regular pin header for ttl - btw: what ist the voltage levels 1.8v or older 3.3v? Only points marked as TX1/RX1 are over the sim card socket below antenna.
External micro usb connector
What did you use to flash dump? https://multi-com.pl/,details,id_pr,22958,key,mt-nor-adapter-dla-procesorow-mediatek-2503dv.html something like that?
Any news on it? If you guys have some insights for now it might be useful to write here everything so other might help and contribute. I bet there are a lot of people who are really interested in solving this problem.
For 2G version see issue #7 I have tested on 3 devices only
I try to change the server ip but
Request:
SERVER,0,148.251.67.210,24871,0#
Response:
ERROR:The domain name or IP is locked,not allowed to modify.
Request:
LOCKIP,WWDSS20,UNLOCK#
Response:
ERROR:101
I also tryed to Factory reset with:
FACTORYALL#
after that i still not can change the IP.What can i do now?