Open neidersun opened 7 years ago
I have exactly the same problem right now. what kind of Multi-Switch are you using? Is the freqency 1420 supported? BTW: you can leave the 0.75 off the frequency. Usually you can use the frequency as listed on lyngsat. I guess you are testing with ARD Digital Transponder on 19.2E ?
I have an LNB D-line uk124 and the 1420 is on the list. SNR is there. Ok, leave the .75 away. No, I use Tagesschau 24. 19.2E ?
the whole transponder is provided by ARD Digital (the broadcasters unit handling DVB-S uplink). Do you have any other software to cross check the setup works? b/c there might be a mumudvb bug, but I can't find it (yet).
Yes, I have tested it with VDR. What is b / c ???
short of because. we need @braice to issue us a test command, or another procedure to find out what VDR does, what mumudvb doesn't do, to setup reception with unicable.
I do not understand, my english is very small
Aaaaa ok I install VDR. And for information of VDR. I have used minidvblinux.de.
Has a lot of log files
http://www.vdr-wiki.de/wiki/index.php/Diseqc.conf http://www.vdr-wiki.de/wiki/index.php/SCR_Single_Cable_Distribution
I found. Unfortunately, I do not understand much and am not a programmer
Hello, I've still found something! The 1420 has SNR but .the 1210 freq does not.
Hello
Can you post your vdr configuration and mumudvb configuration.
Unicable support have been added recently did you checked out the latest git ?
Brice
On Jan 31, 2017 23:16, "neidersun" notifications@github.com wrote:
Hello, I've still found something! The 1420 has SNR but .the 1210 freq does not.
— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/braice/MuMuDVB/issues/158#issuecomment-276568295, or mute the thread https://github.com/notifications/unsubscribe-auth/AAUUD124iZqP7mVE-FbVzFvnMTaHnoRHks5rYAcSgaJpZM4Lx9qP .
Hello, the configurations are as I have seen interlinked and will look for them.
Aa ok New git and I will equal times tomorrow morning test. It is over on sunday
Where you can see that it is a new debug version.
Or want to know the packages and so on. And setting in webinterface.
DiSEqC configuration for VDR
Format:
satellite slof polarization lof command...
satellite: one of the 'S' codes defined in sources.conf the special value 'S360E' means that this entry uses a positioner (command 'P') that can move the dish to any requested satellite position within its range slof: switch frequency of LNB; the first entry with an slof greater than the actual transponder frequency will be used polarization: V = vertical, H = horizontal, L = Left circular, R = Right circular lof: the local oscillator frequency to subtract from the actual transponder frequency command: t tone off T tone on v voltage low (13V) V voltage high (18V) A mini A B mini B Pn use positioner to move dish to satellite position n (or to the satellite's orbital position, if no position number is given) Sn satellite channel routing code sequence for bank n follows Wnn wait nn milliseconds (nn may be any positive integer number) [xx ...] hex code sequence (max. 6)
The 'command...' part is optional.
A line containing space separated integer numbers, terminated with a ':', defines that any following DiSEqC sequences apply only to the given list of device numbers.
Examples:
Full DiSEqC sequence:
S19.2E 11700 V 9750 t v W15 [E0 10 38 F0] W15 A W15 t S19.2E 99999 V 10600 t v W15 [E0 10 38 F1] W15 A W15 T S19.2E 11700 H 9750 t V W15 [E0 10 38 F2] W15 A W15 t S19.2E 99999 H 10600 t V W15 [E0 10 38 F3] W15 A W15 T
S13.0E 11700 V 9750 t v W15 [E0 10 38 F4] W15 B W15 t S13.0E 99999 V 10600 t v W15 [E0 10 38 F5] W15 B W15 T S13.0E 11700 H 9750 t V W15 [E0 10 38 F6] W15 B W15 t S13.0E 99999 H 10600 t V W15 [E0 10 38 F7] W15 B W15 T
Optimized for mini DiSEqC (aka toneburst):
S19.2E 11700 V 9750 t v W15 A W15 t S19.2E 99999 V 10600 t v W15 A W15 T S19.2E 11700 H 9750 t V W15 A W15 t S19.2E 99999 H 10600 t V W15 A W15 T
S13.0E 11700 V 9750 t v W15 B W15 t S13.0E 99999 V 10600 t v W15 B W15 T S13.0E 11700 H 9750 t V W15 B W15 t S13.0E 99999 H 10600 t V W15 B W15 T
Optimized for full DiSEqC:
S19.2E 11700 V 9750 [E0 10 38 F0] S19.2E 99999 V 10600 [E0 10 38 F1] S19.2E 11700 H 9750 [E0 10 38 F2] S19.2E 99999 H 10600 [E0 10 38 F3]
S13.0E 11700 V 9750 [E0 10 38 F4] S13.0E 99999 V 10600 [E0 10 38 F5] S13.0E 11700 H 9750 [E0 10 38 F6] S13.0E 99999 H 10600 [E0 10 38 F7]
DisiCon-4 Single Cable Network:
horizontal: 11.704 - 12.205 GHz (1. IF: 1144 - 1645 MHz) - LOF 1 (10,56 GHz) horizontal: 12.676 - 12.709 GHz (1. IF: 2116 - 2148 MHz) - LOF 1 (10,56 GHz) vertical: 12.035 - 12.107 GHz (1. IF: 955 - 1027 MHz) - LOF 3 (11,08 GHz) vertical: 12.464 - 12.716 GHz (1. IF: 1744 - 1996 MHz) - LOF 2 (10,72 GHz)
S19.2E 99999 H 10560 t v S19.2E 12110 V 11080 t v S19.2E 99999 V 10720 t v
SCR (Satellite Channel Routing) EN50494:
S19.2E 11700 V 9750 t V W10 S0 [E0 10 5A 00 00] W10 v S19.2E 99999 V 10600 t V W10 S1 [E0 10 5A 00 00] W10 v S19.2E 11700 H 9750 t V W10 S2 [E0 10 5A 00 00] W10 v S19.2E 99999 H 10600 t V W10 S3 [E0 10 5A 00 00] W10 v
S13.0E 11700 V 9750 t V W10 S4 [E0 10 5A 00 00] W10 v S13.0E 99999 V 10600 t V W10 S5 [E0 10 5A 00 00] W10 v S13.0E 11700 H 9750 t V W10 S6 [E0 10 5A 00 00] W10 v S13.0E 99999 H 10600 t V W10 S7 [E0 10 5A 00 00] W10 v
SCR (Satellite Channel Routing) EN50607 "JESS":
S19.2E 11700 V 9750 t V W10 S0 [70 00 00 00] W10 v S19.2E 99999 V 10600 t V W10 S1 [70 00 00 00] W10 v S19.2E 11700 H 9750 t V W10 S2 [70 00 00 00] W10 v S19.2E 99999 H 10600 t V W10 S3 [70 00 00 00] W10 v
S13.0E 11700 V 9750 t V W10 S4 [70 00 00 00] W10 v S13.0E 99999 V 10600 t V W10 S5 [70 00 00 00] W10 v S13.0E 11700 H 9750 t V W10 S6 [70 00 00 00] W10 v S13.0E 99999 H 10600 t V W10 S7 [70 00 00 00] W10 v
S23.0E 11700 V 9750 t V W10 S8 [70 00 00 00] W10 v S23.0E 99999 V 10600 t V W10 S9 [70 00 00 00] W10 v S23.0E 11700 H 9750 t V W10 S10 [70 00 00 00] W10 v S23.0E 99999 H 10600 t V W10 S11 [70 00 00 00] W10 v
S28.2E 11700 V 9750 t V W10 S12 [70 00 00 00] W10 v S28.2E 99999 V 10600 t V W10 S13 [70 00 00 00] W10 v S28.2E 11700 H 9750 t V W10 S14 [70 00 00 00] W10 v S28.2E 99999 H 10600 t V W10 S15 [70 00 00 00] W10 v
Positioner for steerable dish:
S360E 11700 V 9750 t V W20 P W20 t v S360E 99999 V 10600 t V W20 P W20 T v S360E 11700 H 9750 t V W20 P W20 t V S360E 99999 H 10600 t V W20 P W20 T V
Hello. found a mistake. It is connected to SCR (Satellite Channel Routing) EN50494: and SCR (Satellite Channel Routing) EN50607 "JESS":
You have SCR Test Diseqc message
and I need for astra:
S19.2E 11700 V 9750 t V W10 S0 [E0 10 5A 00 00] W10 v S19.2E 99999 V 10600 t V W10 S1 [E0 10 5A 00 00] W10 v S19.2E 11700 H 9750 t V W10 S2 [E0 10 5A 00 00] W10 v S19.2E 99999 H 10600 t V W10 S3 [E0 10 5A 00 00] W10 v
I get this with the output of MUMUDVB: E0 10 5a 28 fd 00 len 5
But I need E0 10 5A 00 00
Because you have only the 1024 frq for unicable in it. Because it is clear that only the goes. The tune.c and tune.h must be expanded.
If I could I would help you. I can only read very little.
Hello
Do you have an unicable switch ?
You have specified Deb2: Main: 009 switch_type=n Deb2: Main: 010 switch_input=1 Deb2: Main: 011 uni_freq=1420
In this case the unicable frequency have to be specified in the diseqc message Deb1: Tune: Unicable tuning information : unicable freq 1420 lo_freq 993750 channel byte 0x28 0xfd t 0xfd Deb0: Tune: Test Diseqc message e0 10 5a 28 fd 00 len 5
VDR put 00 00 because it do not know the unicable frequency you want to use.
Are you sure you are using the right unicable frequency, are you sure on the unit? Do VDR tune ? with which unicable frequency ?
The calculation is here
//
https://code.mythtv.org/trac/attachment/ticket/9726/0001-libmythtv-Unicable-SCR-DIN-EN-50494.patch
//seems that we will have to tune to another
frequency too and adjust the voltage //Then we will have to tune the card to the SCR frequency as the LNB change it //https://patchwork.linuxtv.org/patch/7994/
t = (uint16_t) ((((*fefrequency / 1000) + uni_freq
2) / 4) - 350); channel_byte_1 |= (((uint8_t) (t>> 8))& 0x03); channel_byte_2 = (uint8_t) (t& 0x00FF);
if(t>1024)
log_message( log_module, MSG_ERROR,
"SCR/UNICABLE T out of range (is the Scr frequency valid ?) ");
log_message( log_module, MSG_DEBUG, "Unicable
tuning information : unicable freq %d lo_freq %d channel byte 0x\ %02x 0x%02x t 0x%02x", uni_freq, *fefrequency, channel_byte_1, channel_byte_2, t); cmd[0]->cmd.msg[3] = channel_byte_1; cmd[0]->cmd.msg[4] = channel_byte_2;
2017-02-09 19:08 GMT-05:00 neidersun notifications@github.com:
I get this with the output of MUMUDVB: E0 10 5a 28 fd 00 len 5
But I need E0 10 5A 00 00
— You are receiving this because you were mentioned. Reply to this email directly, view it on GitHub https://github.com/braice/MuMuDVB/issues/158#issuecomment-278817850, or mute the thread https://github.com/notifications/unsubscribe-auth/AAUUDwAWvEvzTJJvcJjqk7MKXhOgCjjVks5ra6pmgaJpZM4Lx9qP .
Hello. I got it. it was at the kernel. I have now with the DD Max s 8 and kernel 3.16.0 the debian 8.9 drine is tried.
and driver 0.9.26.
Hello. I have a digital devices max s8 and get always this error.
mumudvb -vvv -s -d -c test.cfg MuMuDVB Version 2.0.0_20150614_mumudvb2 --- Build information --- Built with CAM support. Built with SCAM support. Built with ATSC support. Built with ATSC long channel names support. Built with support for DVB API Version 5.10. Built with support for DVB-T2.
Originally based on dvbstream 0.6 by (C) Dave Chapman 2001-2004 Released under the GPL. Latest version available from http://mumudvb.braice.net/ Project from the cr@ns (http://www.crans.org) by Brice DUBOST (mumudvb@braice.net)
Deb2: Main: ==== Configuration file ==== Deb2: Main: 001 card=4 Deb2: Main: 002 freq=10743.75 Deb2: Main: 003 pol=h Deb2: Main: 004 srate=22000 Deb2: Main: 005 modulation=8PSK Deb2: Main: 006 delivery_system=DVBS Deb2: Main: 007 autoconfiguration=1 Deb2: Main: 008 autoconf_sid_list= 5047 5041 Deb2: Main: 009 switch_type=n Deb2: Main: 010 switch_input=1 Deb2: Main: 011 uni_freq=1420 Deb2: Main: 012 unicast = 1 Deb2: Main: 013 ip_http = 192.168.1.125 Deb2: Main: 014 multicast_ipv4 = 0 Deb2: Main: 015 multicast_iface4 = lo Deb2: Main: 016 rtp_header = 1 Deb2: Main: ============ done =========== Info: Tune: You will use DVB API version 5 for tuning your card. Info: Multicast: You decided to send the RTP header (multicast only). Info: Main: Autoconfiguration, we activate SAP announces. if you want to disable them see the README. Info: Main: Autoconfiguration, we activate PAT rewriting. if you want to disable it see the README. Info: Main: Autoconfiguration, we activate SDT rewriting. if you want to disable it see the README. Info: Main: ========== End of configuration, MuMuDVB version 2.0.0_20150614_mumudvb2 is starting ========== Info: Main: Streaming. Freq 10743750 Info: Tune: Using DVB card "MXL5XX" tuner 0 Info: Tune: Tuning DVB-S to Freq: 993750 kHz, LO frequency 9750000 kHz Pol:H Srate=22000000, LNB number: 0 Info: Tune: LNB voltage 18V Info: Tune: Diseqc switch position specified, we force switch input to 1 Info: Tune: SCR/UNICABLE message Deb1: Tune: Unicable tuning information : unicable freq 1420 lo_freq 993750 channel byte 0x28 0xfd t 0xfd Deb0: Tune: Test Diseqc message e0 10 5a 28 fd 00 len 5 Deb0: Tune: Sending first Diseqc message e0 10 5a 28 fd 00 len 5 Info: Tune: DISEQC SETTING SUCCEDED Info: Tune: Tuning With DVB-API version 5. delivery system : 5 Info: Tune: Stream_id = 0, stream id with PLS parameters 0 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 0 Info: Tune: SNR: 0 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 56424 Info: Tune: SNR: 0 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61339 Info: Tune: SNR: 0 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 60872 Info: Tune: SNR: 1 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61559 Info: Tune: SNR: 1 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61701 Info: Tune: SNR: 150 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61694 Info: Tune: SNR: 431 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61622 Info: Tune: SNR: 716 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61741 Info: Tune: SNR: 1013 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61731 Info: Tune: SNR: 1157 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61724 Info: Tune: SNR: 1051 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61741 Info: Tune: SNR: 1143 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61724 Info: Tune: SNR: 1090 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61721 Info: Tune: SNR: 1075 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61741 Info: Tune: SNR: 1141 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61599 Info: Tune: SNR: 1041 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61731 Info: Tune: SNR: 1144 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61737 Info: Tune: SNR: 1159 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61771 Info: Tune: SNR: 1086 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61728 Info: Tune: SNR: 1115 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61734 Info: Tune: SNR: 1067 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61724 Info: Tune: SNR: 1096 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61731 Info: Tune: SNR: 1110 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61737 Info: Tune: SNR: 1148 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61728 Info: Tune: SNR: 1105 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61737 Info: Tune: SNR: 1127 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61718 Info: Tune: SNR: 1132 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61712 Info: Tune: SNR: 1069 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61718 Info: Tune: SNR: 1145 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61721 Info: Tune: SNR: 1185 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61712 Info: Tune: SNR: 1093 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61718 Info: Tune: SNR: 1201 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61724 Info: Tune: SNR: 1091 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61715 Info: Tune: SNR: 1120 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61712 Info: Tune: SNR: 1184 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61712 Info: Tune: SNR: 1078 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61715 Info: Tune: SNR: 1169 Deb0: Tune: polling.... Info: Tune: FE_STATUS: Info: Tune: Strength: 61728 Info: Tune: SNR: 1109 Info: Main: Card not tuned after timeout - exiting