search

comakingspace / do-something

CoMakingSpace tasks and small projects
21 stars 2 forks source link

Install Prusaslicer on the slicing Computer #126

Closed NitramLegov closed 5 years ago

NitramLegov commented 5 years ago

Prusa released PrusaSlicer (formerly known as Slic3r Prusa Edition or Slic3r PE): https://www.prusa3d.de/prusaslicer/

This should get installed on the computer in the electronics room, which is used for slicing.

It should be checked whether the existint profiles from Slic3r PE should get transferred over to the new version.

LukasFreeze commented 5 years ago

before uninstalling the old one, we should also migrate all useful material/printer settings!

On Tue, Jun 4, 2019 at 9:44 PM NitramLegov notifications@github.com wrote:

Prusa released PrusaSlicer (formerly known as Slic3r Prusa Edition or Slic3r PE): https://www.prusa3d.de/prusaslicer/

This should get installed on the computer in the electronics room, which is used for slicing.

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/comakingspace/do-something/issues/126?email_source=notifications&email_token=AEWXG23GUE6BVUYZCYWQWK3PY3A3DA5CNFSM4HTAO4L2YY3PNVWWK3TUL52HS4DFUVEXG43VMWVGG33NNVSW45C7NFSM4GXTUJRQ, or mute the thread https://github.com/notifications/unsubscribe-auth/AEWXG2YG54NKC2VMXM3E63LPY3A3DANCNFSM4HTAO4LQ .

Pakue95 commented 5 years ago

The last time when we upgraded it asked for an old save file. I’d expect it to do the same.

Am 04.06.2019 um 21:46 schrieb Lukas notifications@github.com:

before uninstalling the old one, we should also migrate all useful material/printer settings!

On Tue, Jun 4, 2019 at 9:44 PM NitramLegov notifications@github.com wrote:

Prusa released PrusaSlicer (formerly known as Slic3r Prusa Edition or Slic3r PE): https://www.prusa3d.de/prusaslicer/

This should get installed on the computer in the electronics room, which is used for slicing.

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/comakingspace/do-something/issues/126?email_source=notifications&email_token=AEWXG23GUE6BVUYZCYWQWK3PY3A3DA5CNFSM4HTAO4L2YY3PNVWWK3TUL52HS4DFUVEXG43VMWVGG33NNVSW45C7NFSM4GXTUJRQ, or mute the thread https://github.com/notifications/unsubscribe-auth/AEWXG2YG54NKC2VMXM3E63LPY3A3DANCNFSM4HTAO4LQ .

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub, or mute the thread.

NitramLegov commented 5 years ago

This time it is not an in-place upgrade but rather a new installation. It will not remove any profiles and stuff, but they have to be imported again after installation. The prusaslicer page contains an explanation: https://blog.prusaprinters.org/prusaslicer-2-release/#_ga=2.14123636.2120555640.1559677387-1180536945.1559677387

LukasFreeze commented 5 years ago

@Narquadah took care of the parallel installation before Wednesday's plenum already, migration pending

Narquadah commented 5 years ago

Mirgration is complete, I will remove the older Slic3r PE version next week unless somebody wants to keep it.

NitramLegov commented 5 years ago

Unfortunately, it seems like Slic3r is still installed on the computer :(

LukasFreeze commented 5 years ago

There was some confusion on the mailing list today, so I guess the deinstall has been taken care of now?

We should still update the Slic3r wiki page with the new policy of maintaining only Prusaslicer on the shared computer, and also write a short Prusaslicer page while we're at it ;-)