Xiaomi Redmi Router AX6000自动重启

smithe-ma commented 3 weeks ago

详细叙述

每24小时内会莫名其妙重启

主机名 OpenWrt 主机型号 Xiaomi Redmi Router AX6000 (CpuMark : 27777.777778 Scores) 架构 ARMv8 Processor x 4 (45.2°C) 固件版本 OpenWrt R24.7.7 / LuCI Master (git-24.182.36151-66d29de) 内核版本 6.1.97

开启如下设置：软件流量分载基于软件的 Routing/NAT 分载硬件流量分载需要硬件 NAT 支持，目前 mt762x 已实现 MTK 无线硬件加速需要硬件支持，目前 Filogic 8x0 已实现 BBR 拥塞控制算法使用 BBR 拥塞控制算法可以有效提升 TCP 网络性能

重复 issue

[X] 没有类似的 issue

具体型号

Xiaomi Redmi Router AX6000

详细日志

内核日志

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.1.97 (admin@iZj6c7khbkoi3ts19wnkjrZ) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r6769-665cedd25) 11.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Sat Jul 13 15:02:08 2024 [ 0.000000] Machine model: Xiaomi Redmi Router AX6000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff] [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff] [ 0.000000] node 0: [mem 0x0000000043030000-0x000000004fbfffff] [ 0.000000] node 0: [mem 0x000000004fc00000-0x000000004ffbffff] [ 0.000000] node 0: [mem 0x000000004ffc0000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.2 [ 0.000000] percpu: Embedded 18 pages/cpu s33768 r8192 d31768 u73728 [ 0.000000] pcpu-alloc: s33768 r8192 d31768 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: GIC system register CPU interface [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024 [ 0.000000] Kernel command line: console=ttyS0,115200n1 loglevel=8 firmware=1 uart_en=1 [ 0.000000] Unknown kernel command line parameters "firmware=1 uart_en=1", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 497108K/524288K available (8448K kernel code, 910K rwdata, 2432K rodata, 448K init, 292K bss, 27180K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GICv3: GIC: Using split EOI/Deactivate mode [ 0.000000] GICv3: 640 SPIs implemented [ 0.000000] GICv3: 0 Extended SPIs implemented [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv3: GICv3 features: 16 PPIs [ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000000c080000 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 timer(s) running at 13.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2ff89eacb, max_idle_ns: 440795202429 ns [ 0.000000] sched_clock: 56 bits at 13MHz, resolution 76ns, wraps every 4398046511101ns [ 0.000120] Calibrating delay loop (skipped), value calculated using timer frequency.. 26.00 BogoMIPS (lpj=130000) [ 0.000128] pid_max: default: 32768 minimum: 301 [ 0.000332] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.000338] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.001012] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.001308] cblist_init_generic: Setting adjustable number of callback queues. [ 0.001311] cblist_init_generic: Setting shift to 2 and lim to 1. [ 0.001398] rcu: Hierarchical SRCU implementation. [ 0.001400] rcu: Max phase no-delay instances is 1000. [ 0.001684] smp: Bringing up secondary CPUs ... [ 0.001943] Detected VIPT I-cache on CPU1 [ 0.001987] cacheinfo: Unable to detect cache hierarchy for CPU 1 [ 0.001994] GICv3: CPU1: found redistributor 1 region 0:0x000000000c0a0000 [ 0.002021] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.002278] Detected VIPT I-cache on CPU2 [ 0.002311] cacheinfo: Unable to detect cache hierarchy for CPU 2 [ 0.002315] GICv3: CPU2: found redistributor 2 region 0:0x000000000c0c0000 [ 0.002326] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.002577] Detected VIPT I-cache on CPU3 [ 0.002607] cacheinfo: Unable to detect cache hierarchy for CPU 3 [ 0.002611] GICv3: CPU3: found redistributor 3 region 0:0x000000000c0e0000 [ 0.002620] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.002645] smp: Brought up 1 node, 4 CPUs [ 0.002649] SMP: Total of 4 processors activated. [ 0.002651] CPU features: detected: 32-bit EL0 Support [ 0.002653] CPU features: detected: CRC32 instructions [ 0.002678] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.002680] CPU: All CPU(s) started at EL2 [ 0.002682] alternatives: applying system-wide alternatives [ 0.005130] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.005146] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.005282] pinctrl core: initialized pinctrl subsystem [ 0.005794] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.006049] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.006069] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.006087] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.006417] thermal_sys: Registered thermal governor 'fair_share' [ 0.006420] thermal_sys: Registered thermal governor 'bang_bang' [ 0.006421] thermal_sys: Registered thermal governor 'step_wise' [ 0.006423] thermal_sys: Registered thermal governor 'user_space' [ 0.006477] ASID allocator initialised with 65536 entries [ 0.006793] pstore: Registered ramoops as persistent store backend [ 0.006795] ramoops: using 0x10000@0x42ff0000, ecc: 0 [ 0.013916] cryptd: max_cpu_qlen set to 1000 [ 0.014547] SCSI subsystem initialized [ 0.014623] libata version 3.00 loaded. [ 0.015513] clocksource: Switched to clocksource arch_sys_counter [ 0.016066] NET: Registered PF_INET protocol family [ 0.016148] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.016532] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.016543] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.016549] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.016570] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.016660] TCP: Hash tables configured (established 4096 bind 4096) [ 0.016780] MPTCP token hash table entries: 512 (order: 1, 12288 bytes, linear) [ 0.016813] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.016823] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.016908] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.016926] PCI: CLS 0 bytes, default 64 [ 0.017779] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 0.020690] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.020699] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.046373] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 0.047040] printk: console [ttyS0] disabled [ 0.067193] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 116, base_baud = 2500000) is a ST16650V2 [ 0.770440] printk: console [ttyS0] enabled [ 0.775189] mtk_rng 1020f000.rng: registered RNG driver [ 0.780647] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 0.789031] loop: module loaded [ 0.793301] spi spi0.0: setup: ignoring unsupported mode bits a00 [ 0.799646] spi-nand spi0.0: ESMT SPI NAND was found. [ 0.804686] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.814046] Signature found at block 1023 [0x07fe0000] [ 0.819175] NMBM management region starts at block 960 [0x07800000] [ 0.829932] First info table with writecount 0 found in block 960 [ 0.849237] Second info table with writecount 0 found in block 963 [ 0.855400] NMBM has been successfully attached [ 0.860112] 8 fixed-partitions partitions found on MTD device spi0.0 [ 0.866466] Creating 8 MTD partitions on "spi0.0": [ 0.871240] 0x000000000000-0x000000100000 : "BL2" [ 0.877091] 0x000000100000-0x000000140000 : "Nvram" [ 0.882455] 0x000000140000-0x000000180000 : "Bdata" [ 0.887818] 0x000000180000-0x000000380000 : "Factory" [ 0.894771] 0x000000380000-0x000000580000 : "FIP" [ 0.901338] 0x000000580000-0x0000005c0000 : "crash" [ 0.906704] 0x0000005c0000-0x000000600000 : "crash_log" [ 0.912369] 0x000000600000-0x000007400000 : "ubi" [ 1.139859] mtk_soc_eth 15100000.ethernet eth0: mediatek frame engine at 0xffffffc009400000, irq 121 [ 1.149409] i2c_dev: i2c /dev entries driver [ 1.154850] mtk-wdt 1001c000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0) [ 1.163331] NET: Registered PF_INET6 protocol family [ 1.168946] Segment Routing with IPv6 [ 1.172616] In-situ OAM (IOAM) with IPv6 [ 1.176574] NET: Registered PF_PACKET protocol family [ 1.181684] 8021q: 802.1Q VLAN Support v1.8 [ 1.186922] pstore: Using crash dump compression: deflate [ 1.244513] mt7530-mdio mdio-bus:1f: configuring for fixed/2500base-x link mode [ 1.253392] mt7530-mdio mdio-bus:1f: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 1.262772] mt7530-mdio mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=125) [ 1.283611] mt7530-mdio mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=126) [ 1.303702] mt7530-mdio mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=127) [ 1.323759] mt7530-mdio mdio-bus:1f wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=128) [ 1.334773] device eth0 entered promiscuous mode [ 1.339414] DSA: tree 0 setup [ 1.343685] UBI: auto-attach mtd7 [ 1.347010] ubi0: default fastmap pool size: 40 [ 1.351524] ubi0: default fastmap WL pool size: 20 [ 1.356314] ubi0: attaching mtd7 [ 3.259988] ubi0: scanning is finished [ 3.288217] ubi0: attached mtd7 (name "ubi", size 110 MiB) [ 3.293700] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.300566] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.307336] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.314276] ubi0: good PEBs: 880, bad PEBs: 0, corrupted PEBs: 0 [ 3.320264] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 3.327466] ubi0: max/mean erase counter: 8/4, WL threshold: 4096, image sequence number: 0 [ 3.335794] ubi0: available PEBs: 0, total reserved PEBs: 880, PEBs reserved for bad PEB handling: 19 [ 3.344992] ubi0: background thread "ubi_bgt0d" started, PID 411 [ 3.354683] block ubiblock0_1: created from ubi0:1(rootfs) [ 3.360184] ubiblock: device ubiblock0_1 (rootfs) set to be root filesystem [ 3.367206] clk: Disabling unused clocks [ 3.390048] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 3.397341] Freeing unused kernel memory: 448K [ 3.401812] Run /sbin/init as init process [ 3.405906] with arguments: [ 3.408858] /sbin/init [ 3.411549] with environment: [ 3.414673] HOME=/ [ 3.417024] TERM=linux [ 3.419716] firmware=1 [ 3.422406] uart_en=1 [ 4.005521] random: crng init done [ 4.381554] init: Console is alive [ 4.385053] init: - watchdog - [ 5.432599] kmodloader: loading kernel modules from /etc/modules-boot.d/ [ 5.582505] kmodloader: done loading kernel modules from /etc/modules-boot.d/ [ 5.596407] init: - preinit - [ 7.438510] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 7.446986] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 7.455618] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 11.982609] mount_root: loading kmods from internal overlay [ 11.995275] kmodloader: loading kernel modules from //etc/modules-boot.d/ [ 12.002500] kmodloader: done loading kernel modules from //etc/modules-boot.d/ [ 12.622843] block: attempting to load /tmp/overlay/upper/etc/config/fstab [ 12.629700] block: unable to load configuration (fstab: Entry not found) [ 12.636420] block: attempting to load /tmp/overlay/etc/config/fstab [ 12.642709] block: unable to load configuration (fstab: Entry not found) [ 12.649425] block: attempting to load /etc/config/fstab [ 12.669149] block: unable to load configuration (fstab: Entry not found) [ 12.675888] block: no usable configuration [ 12.683708] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 12.689447] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 494 [ 12.823836] UBIFS (ubi0:2): recovery needed [ 13.114302] UBIFS (ubi0:2): recovery completed [ 13.118803] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 13.126621] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 13.136515] UBIFS (ubi0:2): FS size: 64757760 bytes (61 MiB, 510 LEBs), max 520 LEBs, journal size 3301376 bytes (3 MiB, 26 LEBs) [ 13.148144] UBIFS (ubi0:2): reserved for root: 3058669 bytes (2986 KiB) [ 13.154739] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 413E7FC1-6538-438F-BCB5-1D521438F3E1, small LPT model [ 13.173779] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 13.202456] block: extroot: not configured [ 13.206637] UBIFS (ubi0:2): un-mount UBI device 0 [ 13.211335] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" stops [ 13.223948] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 13.229679] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 497 [ 13.538143] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 13.545966] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 13.555859] UBIFS (ubi0:2): FS size: 64757760 bytes (61 MiB, 510 LEBs), max 520 LEBs, journal size 3301376 bytes (3 MiB, 26 LEBs) [ 13.567485] UBIFS (ubi0:2): reserved for root: 3058669 bytes (2986 KiB) [ 13.574078] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 413E7FC1-6538-438F-BCB5-1D521438F3E1, small LPT model [ 13.603860] mount_root: loading kmods from internal overlay [ 13.621237] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/ [ 13.635161] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/ [ 13.828423] block: attempting to load /tmp/overlay/upper/etc/config/fstab [ 13.848329] block: extroot: not configured [ 13.853724] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 13.860828] block: extroot: not configured [ 13.870721] mount_root: switching to ubifs overlay [ 13.913864] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. [ 13.974852] urandom-seed: Seeding with /etc/urandom.seed [ 14.122775] procd: - early - [ 14.125748] procd: - watchdog - [ 14.858175] procd: - watchdog - [ 14.870646] procd: - ubus - [ 15.068590] procd: - init - [ 16.629292] kmodloader: loading kernel modules from /etc/modules.d/ [ 16.864845] urngd: v1.0.2 started. [ 16.888476] NET: Registered PF_ALG protocol family [ 16.897248] tun: Universal TUN/TAP device driver, 1.6 [ 16.921393] cryptodev: driver 1.13 loaded. [ 16.927781] crypto-safexcel 10320000.crypto: EIP97:230(0,1,4,4)-HIA:270(0,5,5),PE:150/433(alg:7fcdfc00)/0/0/0 [ 16.958447] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b [ 16.965959] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36 [ 16.986698] xt_time: kernel timezone is -0000 [ 17.009124] mt798x-wmac 18000000.wifi: attaching wed device 0 version 2 [ 17.091774] platform 15010000.wed: MTK WED WO Firmware Version: DEV_000000, Build Time: 20221012175005 [ 17.101165] platform 15010000.wed: MTK WED WO Chip ID 00 Region 3 [ 17.687321] mt798x-wmac 18000000.wifi: HW/SW Version: 0x8a108a10, Build Time: 20221012174648a [ 17.687321] [ 18.024214] mt798x-wmac 18000000.wifi: WM Firmware Version: ____000000, Build Time: 20221012174725 [ 18.063300] mt798x-wmac 18000000.wifi: WA Firmware Version: DEV_000000, Build Time: 20221012174937 [ 18.171110] mt798x-wmac 18000000.wifi: registering led 'mt76-phy0' [ 18.179141] mt798x-wmac 18000000.wifi: registering led 'mt76-phy1' [ 22.014884] PPP generic driver version 2.4.2 [ 22.019896] PPP MPPE Compression module registered [ 22.025252] NET: Registered PF_PPPOX protocol family [ 22.038971] kmodloader: done loading kernel modules from /etc/modules.d/ [ 29.648510] mtk_soc_eth 15100000.ethernet eth0: Link is Down [ 29.659649] mtk_soc_eth 15100000.ethernet eth0: configuring for fixed/2500base-x link mode [ 29.668075] mtk_soc_eth 15100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx [ 29.668878] mt7530-mdio mdio-bus:1f lan2: configuring for phy/gmii link mode [ 29.684146] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 29.690577] br-lan: port 1(lan2) entered blocking state [ 29.695811] br-lan: port 1(lan2) entered disabled state [ 29.703741] device lan2 entered promiscuous mode [ 29.714414] mt7530-mdio mdio-bus:1f lan3: configuring for phy/gmii link mode [ 29.724117] br-lan: port 2(lan3) entered blocking state [ 29.729355] br-lan: port 2(lan3) entered disabled state [ 29.736258] device lan3 entered promiscuous mode [ 29.743930] mt7530-mdio mdio-bus:1f lan4: configuring for phy/gmii link mode [ 29.753589] br-lan: port 3(lan4) entered blocking state [ 29.758818] br-lan: port 3(lan4) entered disabled state [ 29.765812] device lan4 entered promiscuous mode [ 29.774228] mt7530-mdio mdio-bus:1f wan: configuring for phy/gmii link mode [ 29.788714] mt7530-mdio mdio-bus:1f wan: Link is Up - 100Mbps/Full - flow control off [ 29.796595] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready [ 32.350545] br-lan: port 4(wlan0) entered blocking state [ 32.355889] br-lan: port 4(wlan0) entered disabled state [ 32.361413] device wlan0 entered promiscuous mode [ 35.306951] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 35.313458] br-lan: port 4(wlan0) entered blocking state [ 35.318794] br-lan: port 4(wlan0) entered forwarding state [ 35.324449] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 35.454345] br-lan: port 5(wlan1) entered blocking state [ 35.459734] br-lan: port 5(wlan1) entered disabled state [ 35.465286] device wlan1 entered promiscuous mode [ 35.470125] br-lan: port 5(wlan1) entered blocking state [ 35.475429] br-lan: port 5(wlan1) entered forwarding state [ 36.325648] br-lan: port 5(wlan1) entered disabled state [ 36.624145] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 36.630640] br-lan: port 5(wlan1) entered blocking state [ 36.635964] br-lan: port 5(wlan1) entered forwarding state

Turing-China commented 3 weeks ago

我的重启不会;但是编译好了手机和电脑都找不到WIFI信号

smithe-ma commented 3 weeks ago

@Turing-China 2.4和5G一切正常。网络都是好的。就是莫名奇妙重启。我装的东西很少。你也是这个内核和版本吗

smithe-ma commented 3 weeks ago

@aiamadeus 怎么升级6.1.100，重新编译最新的版本吗？

mirthlesslk commented 3 weeks ago

@aiamadeus 64b8009 和 e7646d4 这两个更新之后编译出来的固件，刷入uboot一直重启进不去系统，还原这两个更新就正常，这能修一下吗？

Turing-China commented 3 weeks ago

@Turing-China 2.4和5G一切正常。网络都是好的。就是莫名奇妙重启。我装的东西很少。你也是这个内核和版本吗

@smithe-ma 你重新编译最新内核就是最新的版本另外我5.5 6.1 6.6内核都试过全部都是能看到WIFI配置但是搜索不到WIFI信号;你是云编译的吗?能不能把config 文件发一下；感谢

coolsnowwolf / lede