R7800刷入后启动时间超长

Q：是否搜索了issue (使用 "x" 选择)

[x] 没有类似的issue

详细叙述

R7800定制固件，刷入后第一次开机很正常，大约120秒内能完全启动并使用。但是如果从路由器里点击重启或者断电重启，R7800启动时间突然加长

(1) 具体问题

A：如上所说，附上部分可疑日志，可以看出36秒后有大概3分钟时间机器假死，不知道在干嘛。

Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 36.399768] ath10k_pci 0000:01:00.0: assign IRQ: got 39 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.399789] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.400251] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 36.406649] ath10k_pci 0000:01:00.0: enabling bus mastering Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.407184] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 218.365356] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe Mon Jan 10 21:20:04 2022 kern.info kernel: [ 218.365405] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 218.377910] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 220.757173] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 224.295840] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 224.295864] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.377803] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.378655] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.666728] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761220] ath: EEPROM regdomain sanitized Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761236] ath: EEPROM regdomain: 0x64 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761247] ath: EEPROM indicates we should expect a direct regpair map Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761270] ath: Country alpha2 being used: 00 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761282] ath: Regpair used: 0x64 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.765948] wlan0: Created a NSS virtual interface. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.766001] wlan0: RX-Q and tasklet initialized. Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.775958] ath10k_pci 0001:01:00.0: assign IRQ: got 41 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.776002] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.777929] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.783019] ath10k_pci 0001:01:00.0: enabling bus mastering Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.783745] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 226.338208] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe Mon Jan 10 21:20:04 2022 kern.info kernel: [ 226.338266] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 226.352910] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 228.680126] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 232.234380] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 232.234405] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.318305] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.319179] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.761854] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851203] ath: EEPROM regdomain sanitized Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851219] ath: EEPROM regdomain: 0x64 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851229] ath: EEPROM indicates we should expect a direct regpair map Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851254] ath: Country alpha2 being used: 00 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851264] ath: Regpair used: 0x64 Mon Jan 10 21:20:04 2022 kern.err kernel: [ 232.853810] debugfs: File 'virt_if' in directory 'stats' already present!

(2) 路由器型号和固件版本

A：网件 R7800，固件于1月9日晚在GithubAction云编译。

(3) 详细日志

Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] Booting Linux on physical CPU 0x0 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 0.000000] Linux version 5.4.162 (runner@fv-az269-36) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r4079-60e275903)) #0 SMP Sat Jan 8 07:00:46 2022 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] CPU: div instructions available: patching division code Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] OF: fdt: Machine model: Netgear Nighthawk X4S R7800 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] Memory policy: Data cache writealloc Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.000000] On node 0 totalpages: 122880 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.000000] Normal zone: 1080 pages used for memmap Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.000000] Normal zone: 0 pages reserved Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.000000] Normal zone: 122880 pages, LIFO batch:31 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] percpu: Embedded 15 pages/cpu s30220 r8192 d23028 u61440 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: s30220 r8192 d23028 u61440 alloc=15*4096 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121800 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 0.000000] Kernel command line: Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] Memory: 474820K/491520K available (6263K kernel code, 198K rwdata, 1568K rodata, 1024K init, 232K bss, 16700K reserved, 0K cma-reserved, 0K highmem) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] rcu: Hierarchical RCU implementation. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 0.000000] random: get_random_bytes called from start_kernel+0x340/0x4ec with crng_init=0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000021] Switching to timer-based delay loop, resolution 160ns Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000269] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000288] pid_max: default: 32768 minimum: 301 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000487] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.000505] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.001551] CPU: Testing write buffer coherency: ok Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.002681] Setting up static identity map for 0x42300000 - 0x42300060 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.002857] rcu: Hierarchical SRCU implementation. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.003350] smp: Bringing up secondary CPUs ... Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.005283] smp: Brought up 1 node, 2 CPUs Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.005298] SMP: Total of 2 processors activated (25.00 BogoMIPS). Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.005308] CPU: All CPU(s) started in SVC mode. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.017476] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.017642] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.017671] futex hash table entries: 512 (order: 3, 32768 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.017802] pinctrl core: initialized pinctrl subsystem Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.018952] NET: Registered protocol family 16 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.019249] DMA: preallocated 256 KiB pool for atomic coherent allocations Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.020818] cpuidle: using governor ladder Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.020883] cpuidle: using governor menu Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.056752] usbcore: registered new interface driver usbfs Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.056839] usbcore: registered new interface driver hub Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.056904] usbcore: registered new device driver usb Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.056964] pps_core: LinuxPPS API ver. 1 registered Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.056976] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.057008] PTP clock support registered Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 0.057892] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.059045] clocksource: Switched to clocksource dg_timer Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.059937] thermal_sys: Registered thermal governor 'step_wise' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.062678] NET: Registered protocol family 2 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.062836] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.063689] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.063728] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.063767] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.063821] TCP: Hash tables configured (established 4096 bind 4096) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.063923] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.063956] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.064209] NET: Registered protocol family 1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.064260] PCI: CLS 0 bytes, default 64 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.065593] workingset: timestamp_bits=14 max_order=17 bucket_order=3 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.073229] squashfs: version 4.0 (2009/01/31) Phillip Lougher Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.073245] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 0.111918] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 0.112062] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 0.112172] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.112443] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.112469] qcom-pcie 1b500000.pci: Parsing ranges property... Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.112511] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff -> 0x0fe00000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.112547] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff -> 0x08000000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.334720] qcom-pcie 1b500000.pci: Link up Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.334902] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.334924] pci_bus 0000:00: root bus resource [bus 00-ff] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.334943] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.334959] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.334975] pci_bus 0000:00: scanning bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.335024] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.335193] pci 0000:00:00.0: supports D1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.335207] pci 0000:00:00.0: PME# supported from D0 D1 D3hot Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.335227] pci 0000:00:00.0: PME# disabled Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.339733] pci_bus 0000:00: fixups for bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.339758] PCI: bus0: Fast back to back transfers disabled Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.339779] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.339930] pci_bus 0000:01: scanning bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.340110] pci 0000:01:00.0: [168c:0046] type 00 class 0x028000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.340464] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.341608] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.341653] pci 0000:01:00.0: PME# disabled Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.346176] pci_bus 0000:01: fixups for bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.346248] PCI: bus1: Fast back to back transfers disabled Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.346265] pci_bus 0000:01: bus scan returning with max=01 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.346282] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.346299] pci_bus 0000:00: bus scan returning with max=ff Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.346333] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x081fffff] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.346357] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.346487] pci 0000:00:00.0: PCI bridge to [bus 01-ff] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.346511] pci 0000:00:00.0: bridge window [mem 0x08000000-0x081fffff] Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.346723] pcieport 0000:00:00.0: assign IRQ: got 39 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.347277] pcieport 0000:00:00.0: AER: enabled with IRQ 40 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 0.347858] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 0.347991] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 0.348117] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.348367] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.348388] qcom-pcie 1b700000.pci: Parsing ranges property... Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.348429] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff -> 0x31e00000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.348461] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff -> 0x2e000000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.576420] qcom-pcie 1b700000.pci: Link up Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.576593] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.576612] pci_bus 0001:00: root bus resource [bus 00-ff] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.576627] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.576642] pci_bus 0001:00: scanning bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.576686] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.576831] pci 0001:00:00.0: supports D1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.576845] pci 0001:00:00.0: PME# supported from D0 D1 D3hot Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.576865] pci 0001:00:00.0: PME# disabled Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.581328] pci_bus 0001:00: fixups for bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.581349] PCI: bus0: Fast back to back transfers disabled Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.581368] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.581507] pci_bus 0001:01: scanning bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.581698] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.582075] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.583306] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.583355] pci 0001:01:00.0: PME# disabled Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.583611] pci 0001:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0001:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.587944] pci_bus 0001:01: fixups for bus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.588020] PCI: bus1: Fast back to back transfers disabled Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.588035] pci_bus 0001:01: bus scan returning with max=01 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.588052] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.588068] pci_bus 0001:00: bus scan returning with max=ff Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.588093] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.588117] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.588249] pci 0001:00:00.0: PCI bridge to [bus 01-ff] Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.588270] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 0.588460] pcieport 0001:00:00.0: assign IRQ: got 41 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.589109] pcieport 0001:00:00.0: AER: enabled with IRQ 42 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.591934] L2 @ QSB rate. Forcing new rate. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.592161] L2 @ 384000 KHz Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.592346] CPU0 @ 800000 KHz Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.592359] CPU1 @ QSB rate. Forcing new rate. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.592486] CPU1 @ 384000 KHz Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.596415] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.598701] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.599680] msm_serial 16340000.serial: msm_serial: detected port #0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.599735] msm_serial 16340000.serial: uartclk = 7372800 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.599817] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 43, base_baud = 460800) is a MSM Mon Jan 10 21:20:04 2022 kern.info kernel: [ 0.599856] msm_serial: console setup on port #0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.383021] printk: console [ttyMSM0] enabled Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.388033] msm_serial: driver initialized Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.397596] loop: module loaded Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.399203] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.399657] nand: AMD/Spansion S34MS01G2 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.406144] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.410219] 8 fixed-partitions partitions found on MTD device qcom_nand.0 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.417430] Creating 8 MTD partitions on "qcom_nand.0": Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.424374] 0x000000000000-0x000000c80000 : "qcadata" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.434611] random: fast init done Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.451044] 0x000000c80000-0x000001180000 : "APPSBL" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.460351] 0x000001180000-0x000001200000 : "APPSBLENV" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.462180] 0x000001200000-0x000001340000 : "art" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.467395] 0x000001340000-0x000001480000 : "artbak" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.472314] 0x000001480000-0x000001880000 : "kernel" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.481850] 0x000001880000-0x000007900000 : "ubi" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 1.641029] 0x000007900000-0x000008000000 : "reserve" Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.655223] libphy: ipq8064_mdio_bus: probed Mon Jan 10 21:20:04 2022 kern.info kernel: [ 1.670528] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii Mon Jan 10 21:20:04 2022 kern.err kernel: [ 2.515739] ar8327: qca,phy-rgmii-en is not specified Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.516344] libphy: Fixed MDIO Bus: probed Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.520418] i2c /dev entries driver Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 2.526758] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 2.527277] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.535168] sdhci: Secure Digital Host Controller Interface driver Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.541817] sdhci: Copyright(c) Pierre Ossman Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.547980] sdhci-pltfm: SDHCI platform and OF driver helper Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.554912] NET: Registered protocol family 10 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.559461] Segment Routing with IPv6 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.562479] NET: Registered protocol family 17 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 2.566223] Bridge firewalling registered Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.570755] 8021q: 802.1Q VLAN Support v1.8 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 2.574580] Registering SWP/SWPB emulation handler Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.604958] qcom_rpm 108000.rpm: RPM firmware 3.0.16777364 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.618648] s1a: Bringing 0uV into 1050000-1050000uV Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.618931] s1a: supplied by regulator-dummy Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.622925] s1b: Bringing 0uV into 1050000-1050000uV Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.627154] s1b: supplied by regulator-dummy Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.632079] s2a: Bringing 0uV into 775000-775000uV Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.636348] s2a: supplied by regulator-dummy Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.640973] s2b: Bringing 0uV into 775000-775000uV Mon Jan 10 21:20:04 2022 kern.info kernel: [ 2.645406] s2b: supplied by regulator-dummy Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 2.661554] UBI: auto-attach mtd6 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 2.661575] ubi0: attaching mtd6 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 2.724435] random: crng init done Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.348483] ubi0: scanning is finished Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.357931] ubi0: attached mtd6 (name "ubi", size 96 MiB) Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.357952] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.362368] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.369069] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.375982] ubi0: good PEBs: 772, bad PEBs: 0, corrupted PEBs: 0 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.382762] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.388949] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 1641625246 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.396038] ubi0: available PEBs: 0, total reserved PEBs: 772, PEBs reserved for bad PEB handling: 20 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.405459] ubi0: background thread "ubi_bgt0d" started, PID 68 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 3.406601] block ubiblock0_0: created from ubi0:0(rootfs) Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 3.420188] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem Mon Jan 10 21:20:04 2022 kern.info kernel: [ 3.425670] hctosys: unable to open rtc device (rtc0) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 3.436154] VFS: Mounted root (squashfs filesystem) readonly on device 259:0. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 3.436772] Freeing unused kernel memory: 1024K Mon Jan 10 21:20:04 2022 kern.info kernel: [ 3.469732] Run /sbin/init as init process Mon Jan 10 21:20:04 2022 user.info kernel: [ 4.760540] init: Console is alive Mon Jan 10 21:20:04 2022 user.info kernel: [ 4.760831] init: - watchdog - Mon Jan 10 21:20:04 2022 user.info kernel: [ 8.533068] kmodloader: loading kernel modules from /etc/modules-boot.d/ Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.220169] ANTFS Module: Version 07.19-b41ba529 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.222657] raid6: using algorithm neonx8 gen() 0 MB/s Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.223851] raid6: .... xor() 0 MB/s, rmw enabled Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.228905] raid6: using neon recovery algorithm Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.234991] xor: measuring software checksum speed Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.329395] arm4regs : 1707.600 MB/sec Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.429392] 8regs : 1114.000 MB/sec Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.529391] 32regs : 1078.800 MB/sec Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.629388] neon : 3576.800 MB/sec Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.629404] xor: using function: neon (3576.800 MB/sec) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.692184] Btrfs loaded, crc32c=crc32c-generic Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 9.693686] exfat: module is from the staging directory, the quality is unknown, you have been warned. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.696839] exFAT: Version 1.3.0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.721359] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 9.724204] SCSI subsystem initialized Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 9.730624] libata version 3.00 loaded. Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 9.732575] ahci 29000000.sata: 29000000.sata supply ahci not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 9.732651] ahci 29000000.sata: 29000000.sata supply phy not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 9.739855] ahci 29000000.sata: 29000000.sata supply target not found, using dummy regulator Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.748764] ahci 29000000.sata: forcing port_map 0x0 -> 0x1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.756559] ahci 29000000.sata: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.761852] ahci 29000000.sata: flags: ncq sntf pm led clo only pmp pio slum part ccc apst Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.770938] scsi host0: ahci Mon Jan 10 21:20:04 2022 kern.info kernel: [ 9.778797] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 26 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.112210] ata1: SATA link down (SStatus 0 SControl 300) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.116711] ehci-fsl: Freescale EHCI Host controller driver Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.118046] ehci-platform: EHCI generic platform driver Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.130140] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.131097] ohci-platform: OHCI generic platform driver Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.138044] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.140436] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.146238] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.152400] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.160310] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.163945] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.169762] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.175752] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.184479] dwc3 11000000.dwc3: Failed to get clk 'ref': -2 Mon Jan 10 21:20:04 2022 kern.err kernel: [ 10.248842] dwc3 10000000.dwc3: Failed to get clk 'ref': -2 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.326174] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.326287] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.330978] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.338235] xhci-hcd xhci-hcd.0.auto: irq 47, io mem 0x11000000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.349736] hub 1-0:1.0: USB hub found Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.353512] hub 1-0:1.0: 1 port detected Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.357912] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.361479] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.366614] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.377160] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.381605] hub 2-0:1.0: USB hub found Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.389029] hub 2-0:1.0: 1 port detected Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.393301] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.396643] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.402199] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.409611] xhci-hcd xhci-hcd.1.auto: irq 48, io mem 0x10000000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.421617] hub 3-0:1.0: USB hub found Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.424810] hub 3-0:1.0: 1 port detected Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.428853] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.432708] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.437948] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.445811] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.452754] hub 4-0:1.0: USB hub found Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.460425] hub 4-0:1.0: 1 port detected Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.466923] usbcore: registered new interface driver usb-storage Mon Jan 10 21:20:04 2022 kern.info kernel: [ 10.468848] usbcore: registered new interface driver uas Mon Jan 10 21:20:04 2022 user.info kernel: [ 10.474183] kmodloader: done loading kernel modules from /etc/modules-boot.d/ Mon Jan 10 21:20:04 2022 user.info kernel: [ 10.484841] init: - preinit - Mon Jan 10 21:20:04 2022 user.info kernel: [ 20.699716] mount_root: loading kmods from internal overlay Mon Jan 10 21:20:04 2022 user.info kernel: [ 20.775845] kmodloader: loading kernel modules from //etc/modules-boot.d/ Mon Jan 10 21:20:04 2022 user.info kernel: [ 20.784805] kmodloader: done loading kernel modules from //etc/modules-boot.d/ Mon Jan 10 21:20:04 2022 user.info kernel: [ 26.812713] block: attempting to load /etc/config/fstab Mon Jan 10 21:20:04 2022 user.err kernel: [ 26.814451] block: unable to load configuration (fstab: Entry not found) Mon Jan 10 21:20:04 2022 user.err kernel: [ 26.816870] block: no usable configuration Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 26.829388] UBIFS (ubi0:1): Mounting in unauthenticated mode Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 26.839897] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 158 Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 27.179910] UBIFS (ubi0:1): recovery needed Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 28.149422] UBIFS (ubi0:1): recovery completed Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 28.149512] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 28.152749] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 28.160704] UBIFS (ubi0:1): FS size: 67805184 bytes (64 MiB, 534 LEBs), journal size 3428352 bytes (3 MiB, 27 LEBs) Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 28.170608] UBIFS (ubi0:1): reserved for root: 3202606 bytes (3127 KiB) Mon Jan 10 21:20:04 2022 kern.notice kernel: [ 28.180861] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 127F2FF0-40A6-4396-94A2-15C44A4E8317, small LPT model Mon Jan 10 21:20:04 2022 user.info kernel: [ 28.249696] mount_root: loading kmods from internal overlay Mon Jan 10 21:20:04 2022 user.info kernel: [ 28.301513] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/ Mon Jan 10 21:20:04 2022 user.info kernel: [ 28.303494] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/ Mon Jan 10 21:20:04 2022 user.info kernel: [ 29.340599] block: attempting to load /etc/config/fstab Mon Jan 10 21:20:04 2022 user.err kernel: [ 29.340706] block: unable to load configuration (fstab: Entry not found) Mon Jan 10 21:20:04 2022 user.err kernel: [ 29.344672] block: no usable configuration Mon Jan 10 21:20:04 2022 user.info kernel: [ 29.352881] mount_root: switching to ubifs overlay Mon Jan 10 21:20:04 2022 user.warn kernel: [ 29.374904] urandom-seed: Seeding with /etc/urandom.seed Mon Jan 10 21:20:04 2022 user.info kernel: [ 33.555557] procd: - early - Mon Jan 10 21:20:04 2022 user.info kernel: [ 33.555873] procd: - watchdog - Mon Jan 10 21:20:04 2022 user.info kernel: [ 34.485197] procd: - watchdog - Mon Jan 10 21:20:04 2022 user.info kernel: [ 34.490530] procd: - ubus - Mon Jan 10 21:20:04 2022 user.info kernel: [ 34.675282] procd: - init - Mon Jan 10 21:20:04 2022 user.info kernel: [ 35.731012] kmodloader: loading kernel modules from /etc/modules.d/* Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.750711] NET: Registered protocol family 38 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.768243] NET: Registered protocol family 15 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.770656] Initializing XFRM netlink socket Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.773867] tun: Universal TUN/TAP device driver, 1.6 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.781292] ** Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.781359] Driver :NSS GMAC Driver - RTL v(3.72a) Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.787374] Version :1.0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.792567] * Copyright :Copyright (c) 2013-2018 The Linux Foundation. All rights reserved. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.795657] ** Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.850570] nss_driver - fw of size 536324 bytes copied to load addr: 40000000, nss_id : 0 Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.850993] nss_driver - Turbo Support 1 Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.857713] Supported Frequencies - Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.857715] 800Mhz Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.861956] 800Mhz Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.865434] 800Mhz Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.867259] Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.871619] c747bc4c: meminfo init succeed Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.882156] nss_driver - fw of size 218224 bytes copied to load addr: 40800000, nss_id : 1 Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.882373] 22963d58: meminfo init succeed Mon Jan 10 21:20:04 2022 kern.err kernel: [ 35.889433] debugfs: File 'n2h' in directory 'stats' already present! Mon Jan 10 21:20:04 2022 kern.err kernel: [ 35.893472] debugfs: File 'qrfs' in directory 'stats' already present! Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.899928] node size 1 # items 2 Mon Jan 10 21:20:04 2022 kern.err kernel: [ 35.900041] debugfs: File 'c2c_tx' in directory 'stats' already present! Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.906400] memory: 0 0 (avl 487276544) items 2 active_cores 2 Mon Jan 10 21:20:04 2022 kern.err kernel: [ 35.909849] debugfs: File 'c2c_rx' in directory 'stats' already present! Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.916560] c747bc4c: nss core 0 booted successfully Mon Jan 10 21:20:04 2022 kern.err kernel: [ 35.922251] debugfs: File 'unaligned' in directory 'stats' already present! Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.935843] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.936790] node size 1 # items 2 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.946085] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.946624] memory: 0 0 (avl 487276544) items 2 active_cores 2 Mon Jan 10 21:20:04 2022 kern.alert kernel: [ 35.956520] 22963d58: nss core 1 booted successfully Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.993317] cryptodev: driver 1.12 loaded. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.996768] PPP generic driver version 2.4.2 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 35.999328] NET: Registered protocol family 24 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.008242] GACT probability on Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.008925] Mirror/redirect action on Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.015402] u32 classifier Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.015421] input device check on Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.016992] Actions configured Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.029728] usbcore: registered new interface driver cdc_wdm Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.031583] Loading modules backported from Linux version v5.10.42-0-g65859eca4dff Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.034446] Backport generated by backports.git v5.10.42-1-0-gbee5c545 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.051253] hso: drivers/net/usb/hso.c: Option Wireless Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.051350] usbcore: registered new interface driver hso Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.057208] usbcore: registered new interface driver ipheth Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.072670] usbcore: registered new interface driver kaweth Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.118093] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.118187] usbcore: registered new interface driver pegasus Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.126792] PPP MPPE Compression module registered Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.140998] usbcore: registered new interface driver rtl8150 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.144526] usbcore: registered new interface driver ums-alauda Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.146778] usbcore: registered new interface driver ums-cypress Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.157035] usbcore: registered new interface driver ums-datafab Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.158631] usbcore: registered new interface driver ums-freecom Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.164759] usbcore: registered new interface driver ums-isd200 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.170899] usbcore: registered new interface driver ums-jumpshot Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.176400] usbcore: registered new interface driver ums-karma Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.192738] usbcore: registered new interface driver ums-sddr09 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.193939] usbcore: registered new interface driver ums-sddr55 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.198684] usbcore: registered new interface driver ums-usbat Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.207450] usbcore: registered new interface driver usblp Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.233905] xt_time: kernel timezone is -0000 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.234699] usbcore: registered new interface driver aqc111 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.238352] usbcore: registered new interface driver asix Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.243653] usbcore: registered new interface driver ax88179_178a Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.248906] usbcore: registered new interface driver cdc_eem Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.255427] usbcore: registered new interface driver cdc_ether Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.261675] usbcore: registered new interface driver cdc_ncm Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.266334] usbcore: registered new interface driver cdc_subset Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.285887] usbcore: registered new interface driver dm9601 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.286407] usbcore: registered new interface driver huawei_cdc_ncm Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.292079] usbcore: registered new interface driver kalmia Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.318237] usbcore: registered new interface driver MOSCHIP usb-ethernet driver Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.318938] usbcore: registered new interface driver plusb Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.325797] usbcore: registered new interface driver qmi_wwan Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.331334] usbcore: registered new interface driver rndis_host Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.336831] usbcore: registered new interface driver sierra_net Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.358119] usbcore: registered new interface driver smsc95xx Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.359148] usbcore: registered new interface driver sr9700 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.365071] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.368218] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld Jason@zx2c4.com. All Rights Reserved. Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 36.399768] ath10k_pci 0000:01:00.0: assign IRQ: got 39 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.399789] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.400251] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 36.406649] ath10k_pci 0000:01:00.0: enabling bus mastering Mon Jan 10 21:20:04 2022 kern.info kernel: [ 36.407184] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 218.365356] ath10k_pci 0000:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe Mon Jan 10 21:20:04 2022 kern.info kernel: [ 218.365405] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 218.377910] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 220.757173] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 224.295840] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 224.295864] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.377803] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.378655] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.666728] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761220] ath: EEPROM regdomain sanitized Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761236] ath: EEPROM regdomain: 0x64 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761247] ath: EEPROM indicates we should expect a direct regpair map Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761270] ath: Country alpha2 being used: 00 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.761282] ath: Regpair used: 0x64 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.765948] wlan0: Created a NSS virtual interface. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.766001] wlan0: RX-Q and tasklet initialized. Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.775958] ath10k_pci 0001:01:00.0: assign IRQ: got 41 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.776002] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.777929] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 224.783019] ath10k_pci 0001:01:00.0: enabling bus mastering Mon Jan 10 21:20:04 2022 kern.info kernel: [ 224.783745] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 226.338208] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe Mon Jan 10 21:20:04 2022 kern.info kernel: [ 226.338266] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 226.352910] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 7ea63dc5 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 228.680126] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 232.234380] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 Mon Jan 10 21:20:04 2022 kern.warn kernel: [ 232.234405] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.318305] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.319179] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.761854] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851203] ath: EEPROM regdomain sanitized Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851219] ath: EEPROM regdomain: 0x64 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851229] ath: EEPROM indicates we should expect a direct regpair map Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851254] ath: Country alpha2 being used: 00 Mon Jan 10 21:20:04 2022 kern.debug kernel: [ 232.851264] ath: Regpair used: 0x64 Mon Jan 10 21:20:04 2022 kern.err kernel: [ 232.853810] debugfs: File 'virt_if' in directory 'stats' already present! Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.854121] wlan1: Created a NSS virtual interface. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.859705] wlan1: RX-Q and tasklet initialized. Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.876248] batman_adv: B.A.T.M.A.N. advanced 2021.4-openwrt-1 (compatibility version 15) loaded Mon Jan 10 21:20:04 2022 kern.info kernel: [ 232.878083] usbcore: registered new interface driver cdc_mbim Mon Jan 10 21:20:04 2022 user.info kernel: [ 232.884550] kmodloader: done loading kernel modules from /etc/modules.d/* Mon Jan 10 21:20:04 2022 daemon.notice procd: /etc/rc.d/S15cpu_freq: vm.min_free_kbytes = 65536 Mon Jan 10 21:20:04 2022 daemon.notice procd: /etc/rc.d/S15cpu_freq: net.netfilter.nf_conntrack_max = 65535 Mon Jan 10 21:20:05 2022 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses! Mon Jan 10 21:20:05 2022 user.notice dnsmasq: Allowing 127.0.0.0/8 responses Mon Jan 10 21:20:07 2022 kern.info kernel: [ 237.724759] ECM init Mon Jan 10 21:20:07 2022 kern.info kernel: [ 237.724821] ECM database jhash random seed: 0xa8b9dafc Mon Jan 10 21:20:07 2022 kern.info kernel: [ 237.727978] ECM init complete Mon Jan 10 21:20:07 2022 daemon.notice procd: /etc/rc.d/S19qca-nss-ecm: net.bridge.bridge-nf-call-ip6tables = 1 Mon Jan 10 21:20:07 2022 daemon.notice procd: /etc/rc.d/S19qca-nss-ecm: net.bridge.bridge-nf-call-iptables = 1 Mon Jan 10 21:20:07 2022 daemon.notice procd: /etc/rc.d/S19qca-nss-ecm: dev.nss.general.redirect = 1 Mon Jan 10 21:20:09 2022 daemon.notice wpa_supplicant[1430]: Successfully initialized wpa_supplicant Mon Jan 10 21:20:09 2022 user.notice : Added device handler type: 8021ad Mon Jan 10 21:20:09 2022 user.notice : Added device handler type: 8021q Mon Jan 10 21:20:09 2022 user.notice : Added device handler type: macvlan Mon Jan 10 21:20:09 2022 user.notice : Added device handler type: veth Mon Jan 10 21:20:09 2022 user.notice : Added device handler type: bridge Mon Jan 10 21:20:09 2022 user.notice : Added device handler type: Network device Mon Jan 10 21:20:09 2022 user.notice : Added device handler type: tunnel Mon Jan 10 21:20:10 2022 daemon.err block: No "mount.ubi" utility available Mon Jan 10 21:20:10 2022 daemon.err block: mounting /dev/mtdblock6 (ubi) as /mnt/mtdblock6 failed (25) - Not a tty Mon Jan 10 21:20:10 2022 daemon.notice procd: /etc/rc.d/S50autoreboot: Command failed: Not found Mon Jan 10 21:20:10 2022 daemon.notice procd: /etc/rc.d/S50autoreboot: Auto REBOOT has started. Mon Jan 10 21:20:10 2022 kern.info kernel: [ 241.163237] ipq8064-mdio 37000000.mdio eth1: 1000 Mbps Full Duplex Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.254159] br-lan: port 1(eth1.1) entered blocking state Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.254201] br-lan: port 1(eth1.1) entered disabled state Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.259048] device eth1.1 entered promiscuous mode Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.264042] device eth1 entered promiscuous mode Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.273018] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.282168] br-lan: port 1(eth1.1) entered blocking state Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.282205] br-lan: port 1(eth1.1) entered forwarding state Mon Jan 10 21:20:11 2022 daemon.notice netifd: Interface 'lan' is enabled Mon Jan 10 21:20:11 2022 daemon.notice netifd: bridge 'br-lan' link is up Mon Jan 10 21:20:11 2022 daemon.notice netifd: Interface 'lan' has link connectivity Mon Jan 10 21:20:11 2022 daemon.notice netifd: Interface 'lan' is setting up now Mon Jan 10 21:20:11 2022 daemon.notice netifd: Interface 'lan' is now up Mon Jan 10 21:20:11 2022 daemon.notice netifd: VLAN 'eth1.1' link is up Mon Jan 10 21:20:11 2022 daemon.notice netifd: Interface 'loopback' is enabled Mon Jan 10 21:20:11 2022 daemon.notice netifd: Interface 'loopback' is setting up now Mon Jan 10 21:20:11 2022 daemon.notice netifd: Interface 'loopback' is now up Mon Jan 10 21:20:11 2022 kern.info kernel: [ 242.310389] ipq8064-mdio 37000000.mdio eth0: 1000 Mbps Full Duplex Mon Jan 10 21:20:13 2022 kern.info kernel: [ 243.458577] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready Mon Jan 10 21:20:13 2022 kern.info kernel: [ 243.458867] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Mon Jan 10 21:20:13 2022 kern.info kernel: [ 243.466305] device eth0 entered promiscuous mode Mon Jan 10 21:20:13 2022 daemon.notice netifd: Interface 'wan' is enabled Mon Jan 10 21:20:13 2022 daemon.notice netifd: Network device 'eth1' link is up Mon Jan 10 21:20:13 2022 daemon.notice netifd: Network device 'lo' link is up Mon Jan 10 21:20:13 2022 daemon.notice netifd: Interface 'loopback' has link connectivity Mon Jan 10 21:20:13 2022 daemon.notice netifd: Network device 'eth0' link is up Mon Jan 10 21:20:13 2022 daemon.notice netifd: VLAN 'eth0.2' link is up Mon Jan 10 21:20:13 2022 daemon.notice netifd: Interface 'wan' has link connectivity Mon Jan 10 21:20:13 2022 daemon.notice netifd: Interface 'wan' is setting up now Mon Jan 10 21:20:13 2022 daemon.err insmod: module is already loaded - slhc Mon Jan 10 21:20:13 2022 daemon.err insmod: module is already loaded - ppp_generic Mon Jan 10 21:20:13 2022 daemon.err insmod: module is already loaded - pppox Mon Jan 10 21:20:13 2022 daemon.err insmod: module is already loaded - pppoe Mon Jan 10 21:20:13 2022 authpriv.warn dropbear[2183]: Failed listening on '22': Error listening: Address not available Mon Jan 10 21:20:13 2022 authpriv.info dropbear[2183]: Not backgrounding Mon Jan 10 21:20:13 2022 daemon.info pppd[2161]: Plugin pppoe.so loaded. Mon Jan 10 21:20:13 2022 daemon.info pppd[2161]: PPPoE plugin from pppd 2.4.9 Mon Jan 10 21:20:13 2022 daemon.notice pppd[2161]: pppd 2.4.9 started by root, uid 0 Mon Jan 10 21:20:13 2022 kern.info kernel: [ 244.050577] wlan1: Destroyed NSS virtual interface Mon Jan 10 21:20:13 2022 kern.info kernel: [ 244.050600] wlan1: RX-Q purged. Mon Jan 10 21:20:13 2022 kern.info kernel: [ 244.130199] wlan0: Destroyed NSS virtual interface Mon Jan 10 21:20:13 2022 kern.info kernel: [ 244.130220] wlan0: RX-Q purged. Mon Jan 10 21:20:14 2022 daemon.err odhcpd[1564]: Failed to send to ff02::1%lan@br-lan (Address not available) Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486195] ath: EEPROM regdomain: 0x8348 Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486200] ath: EEPROM indicates we should expect a country code Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486204] ath: doing EEPROM country->regdmn map search Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486207] ath: country maps to regdmn code: 0x3a Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486210] ath: Country alpha2 being used: US Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486213] ath: Regpair used: 0x3a Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486216] ath: regdomain 0x8348 dynamically updated by user Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486234] ath: EEPROM regdomain: 0x8348 Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486236] ath: EEPROM indicates we should expect a country code Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486239] ath: doing EEPROM country->regdmn map search Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486242] ath: country maps to regdmn code: 0x3a Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486244] ath: Country alpha2 being used: US Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486246] ath: Regpair used: 0x3a Mon Jan 10 21:20:14 2022 kern.debug kernel: [ 244.486250] ath: regdomain 0x8348 dynamically updated by user Mon Jan 10 21:20:14 2022 user.notice mwan3[1794]: Using firewall mask 0x3F00 Mon Jan 10 21:20:14 2022 user.notice mwan3[1794]: Max interface count is 60 Mon Jan 10 21:20:15 2022 kern.err kernel: [ 246.096777] debugfs: File 'virt_if' in directory 'stats' already present! Mon Jan 10 21:20:15 2022 kern.info kernel: [ 246.097092] wlan0: Created a NSS virtual interface. Mon Jan 10 21:20:15 2022 kern.info kernel: [ 246.102672] wlan0: RX-Q and tasklet initialized. Mon Jan 10 21:20:15 2022 kern.err kernel: [ 246.110063] debugfs: File 'virt_if' in directory 'stats' already present! Mon Jan 10 21:20:15 2022 kern.info kernel: [ 246.112581] wlan1: Created a NSS virtual interface. Mon Jan 10 21:20:15 2022 kern.info kernel: [ 246.118832] wlan1: RX-Q and tasklet initialized. Mon Jan 10 21:20:15 2022 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy0.conf (phy wlan0) --> new PHY Mon Jan 10 21:20:16 2022 daemon.warn procd: Seccomp support for umdns::instance1 not available Mon Jan 10 21:20:16 2022 user.notice firewall: Reloading firewall due to ifup of lan (br-lan) Mon Jan 10 21:20:21 2022 kern.warn kernel: [ 252.096164] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 Mon Jan 10 21:20:21 2022 kern.warn kernel: [ 252.096190] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 Mon Jan 10 21:20:21 2022 kern.info kernel: [ 252.178277] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' Mon Jan 10 21:20:21 2022 kern.info kernel: [ 252.179115] ath10k_pci 0000:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' Mon Jan 10 21:20:22 2022 kern.info kernel: [ 252.561520] ath10k_pci 0000:01:00.0: rts threshold -1 Mon Jan 10 21:20:22 2022 kern.warn kernel: [ 252.561840] ath10k_pci 0000:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 Mon Jan 10 21:20:22 2022 kern.info kernel: [ 252.578551] br-lan: port 2(wlan0) entered blocking state Mon Jan 10 21:20:22 2022 kern.info kernel: [ 252.578618] br-lan: port 2(wlan0) entered disabled state Mon Jan 10 21:20:22 2022 kern.info kernel: [ 252.583480] device wlan0 entered promiscuous mode Mon Jan 10 21:20:22 2022 kern.info kernel: [ 252.588385] br-lan: port 2(wlan0) entered blocking state Mon Jan 10 21:20:22 2022 kern.info kernel: [ 252.592908] br-lan: port 2(wlan0) entered forwarding state Mon Jan 10 21:20:22 2022 daemon.notice hostapd: wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE Mon Jan 10 21:20:22 2022 daemon.notice hostapd: wlan0: interface state COUNTRY_UPDATE->HT_SCAN Mon Jan 10 21:20:22 2022 daemon.notice hostapd: Configuration file: /var/run/hostapd-phy1.conf (phy wlan1) --> new PHY Mon Jan 10 21:20:22 2022 kern.info kernel: [ 252.808580] ath10k_pci 0000:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 Mon Jan 10 21:20:22 2022 daemon.notice procd: /etc/rc.d/S90kms: KMS Server has started. Mon Jan 10 21:20:22 2022 daemon.notice procd: /etc/rc.d/S90turboacc: net.ipv4.tcp_congestion_control = cubic Mon Jan 10 21:20:22 2022 daemon.notice procd: /etc/rc.d/S90turboacc: killall: dnscache: no process killed Mon Jan 10 21:20:22 2022 daemon.notice procd: /etc/rc.d/S90turboacc: sh: you need to specify whom to kill Mon Jan 10 21:20:22 2022 daemon.notice procd: /etc/rc.d/S90turboacc: Stop DNS Caching Mon Jan 10 21:20:27 2022 daemon.info procd: Instance dnsmasq::cfg01411c pid 3437 not stopped on SIGTERM, sending SIGKILL instead Mon Jan 10 21:20:28 2022 kern.warn kernel: [ 258.672422] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 Mon Jan 10 21:20:28 2022 kern.warn kernel: [ 258.672454] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 Mon Jan 10 21:20:28 2022 kern.info kernel: [ 258.756602] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' Mon Jan 10 21:20:28 2022 kern.info kernel: [ 258.757486] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' Mon Jan 10 21:20:28 2022 daemon.warn pppd[2161]: Timeout waiting for PADO packets Mon Jan 10 21:20:28 2022 daemon.err pppd[2161]: Unable to complete PPPoE Discovery Mon Jan 10 21:20:28 2022 daemon.info pppd[2161]: Exit. Mon Jan 10 21:20:28 2022 kern.info kernel: [ 259.389623] ath10k_pci 0001:01:00.0: rts threshold -1 Mon Jan 10 21:20:28 2022 kern.warn kernel: [ 259.390457] ath10k_pci 0001:01:00.0: Firmware lacks feature flag indicating a retry limit of > 2 is OK, requested limit: 4 Mon Jan 10 21:20:29 2022 kern.info kernel: [ 259.394607] br-lan: port 2(wlan0) entered disabled state Mon Jan 10 21:20:29 2022 kern.info kernel: [ 259.426652] br-lan: port 3(wlan1) entered blocking state Mon Jan 10 21:20:29 2022 kern.info kernel: [ 259.426685] br-lan: port 3(wlan1) entered disabled state Mon Jan 10 21:20:29 2022 kern.info kernel: [ 259.431741] device wlan1 entered promiscuous mode Mon Jan 10 21:20:29 2022 daemon.err uhttpd[2893]: cat: can't open '/etc/bench.log': No such file or directory Mon Jan 10 21:20:29 2022 daemon.notice hostapd: wlan1: interface state UNINITIALIZED->COUNTRY_UPDATE Mon Jan 10 21:20:29 2022 kern.info kernel: [ 259.820741] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready Mon Jan 10 21:20:29 2022 kern.info kernel: [ 259.820976] br-lan: port 3(wlan1) entered blocking state Mon Jan 10 21:20:29 2022 kern.info kernel: [ 259.826217] br-lan: port 3(wlan1) entered forwarding state Mon Jan 10 21:20:29 2022 daemon.err uhttpd[2893]: cat: can't open '/etc/bench.log': No such file or directory Mon Jan 10 21:20:29 2022 daemon.notice hostapd: wlan1: interface state COUNTRY_UPDATE->ENABLED Mon Jan 10 21:20:29 2022 daemon.notice hostapd: wlan1: AP-ENABLED Mon Jan 10 21:20:29 2022 daemon.notice netifd: Interface 'wan' is now down Mon Jan 10 21:20:29 2022 kern.info kernel: [ 260.131115] device eth0 left promiscuous mode Mon Jan 10 21:20:29 2022 kern.info kernel: [ 260.141984] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Mon Jan 10 21:20:29 2022 kern.info kernel: [ 260.142223] br-lan: port 2(wlan0) entered blocking state Mon Jan 10 21:20:29 2022 kern.info kernel: [ 260.147438] br-lan: port 2(wlan0) entered forwarding state Mon Jan 10 21:20:29 2022 daemon.notice hostapd: wlan0: interface state HT_SCAN->ENABLED Mon Jan 10 21:20:29 2022 daemon.notice hostapd: wlan0: AP-ENABLED Mon Jan 10 21:20:30 2022 daemon.notice netifd: Interface 'wan' is disabled Mon Jan 10 21:20:30 2022 kern.info kernel: [ 260.462181] ipq8064-mdio 37000000.mdio eth0: 1000 Mbps Full Duplex Mon Jan 10 21:20:30 2022 daemon.notice netifd: Interface 'wan' is enabled Mon Jan 10 21:20:30 2022 daemon.notice netifd: Interface 'wan' is setting up now Mon Jan 10 21:20:30 2022 kern.info kernel: [ 260.470817] device eth0 entered promiscuous mode Mon Jan 10 21:20:30 2022 daemon.notice netifd: Network device 'wlan0' link is up Mon Jan 10 21:20:30 2022 daemon.err insmod: module is already loaded - slhc Mon Jan 10 21:20:30 2022 daemon.err insmod: module is already loaded - ppp_generic Mon Jan 10 21:20:30 2022 daemon.err insmod: module is already loaded - pppox Mon Jan 10 21:20:30 2022 daemon.err insmod: module is already loaded - pppoe Mon Jan 10 21:20:30 2022 daemon.info pppd[3848]: Plugin pppoe.so loaded. Mon Jan 10 21:20:30 2022 daemon.info pppd[3848]: PPPoE plugin from pppd 2.4.9 Mon Jan 10 21:20:30 2022 daemon.notice pppd[3848]: pppd 2.4.9 started by root, uid 0 Mon Jan 10 21:20:31 2022 daemon.notice netifd: Network device 'wlan1' link is up Mon Jan 10 21:20:31 2022 daemon.notice procd: /etc/rc.d/S90turboacc: DNSMASQ change

coolsnowwolf / lede