CPU: Allwinner R40 (SUN8I 1701)
Model: Banana Pi BPI-M2-Ultra
I2C: ready
DRAM: 2 GiB
MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... *** Warning - bad CRC, using default environment
In: serial@1c28000
Out: serial@1c28000
Err: serial@1c28000
Net: phy interface7
eth0: ethernet@1c50000
starting USB...
Bus usb@1c19000: failed to get usb phy
Port not available.
Bus usb@1c19400: failed to get usb phy
Port not available.
Bus usb@1c1c000: failed to get usb phy
Port not available.
Bus usb@1c1c400: failed to get usb phy
Port not available.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
377 bytes read in 2 ms (183.6 KiB/s)
Executing script at 43100000
3272896 bytes read in 149 ms (20.9 MiB/s)
17640 bytes read in 3 ms (5.6 MiB/s)
Booting kernel from Legacy Image at 42000000 ...
Image Name: ARM OpenWrt Linux-5.4.172
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3272832 Bytes = 3.1 MiB
Load Address: 40008000
Entry Point: 40008000
Verifying Checksum ... OK
Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000
Loading Kernel Image
Using Device Tree in place at 43000000, end 430074e7
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 5.4.172 (yu@yu-n3455) (gcc version 8.4.0 (OpenWrt G CC 8.4.0 r4106-ddb86302d)) #0 SMP Mon Jan 17 14:31:40 2022
[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=30c5387d
[ 0.000000] CPU: div instructions available: patching division code
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache
[ 0.000000] OF: fdt: Machine model: Banana Pi BPI-M2-Ultra
[ 0.000000] Memory policy: Data cache writealloc
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: Using PSCI v0.1 Function IDs from DT
[ 0.000000] percpu: Embedded 15 pages/cpu s30924 r8192 d22324 u61440
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560
[ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk root=/dev/m mcblk0p2 rootwait
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, li near)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 2064616K/2097152K available (6671K kernel code, 426K rwda ta, 1820K rodata, 2048K init, 246K bss, 32536K reserved, 0K cma-reserved, 131070 8K highmem)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2force probe not set
[ 0.000000] random: get_random_bytes called from start_kernel+0x2fc/0x4ac wit h crng_init=0
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns
[ 0.000016] Switching to timer-based delay loop, resolution 41ns
[ 0.000125] Console: colour dummy device 80x30
[ 0.000175] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=240000)
[ 0.000187] pid_max: default: 32768 minimum: 301
[ 0.000357] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linea r)
[ 0.000372] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.001259] CPU: Testing write buffer coherency: ok
[ 0.001629] /cpus/cpu@0 missing clock-frequency property
[ 0.001646] /cpus/cpu@1 missing clock-frequency property
[ 0.001660] /cpus/cpu@2 missing clock-frequency property
[ 0.001673] /cpus/cpu@3 missing clock-frequency property
[ 0.001683] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.002162] Setting up static identity map for 0x40200000 - 0x40200060
[ 0.002272] rcu: Hierarchical SRCU implementation.
[ 0.002748] smp: Bringing up secondary CPUs ...
[ 0.013454] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.024237] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002
[ 0.034968] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003
[ 0.035052] smp: Brought up 1 node, 4 CPUs
[ 0.035069] SMP: Total of 4 processors activated (192.00 BogoMIPS).
[ 0.035075] CPU: All CPU(s) started in HYP mode.
[ 0.035080] CPU: Virtualization extensions available.
[ 0.039530] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[ 0.039754] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.039774] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[ 0.040030] pinctrl core: initialized pinctrl subsystem
[ 0.041108] NET: Registered protocol family 16
[ 0.041789] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.042832] No ATAGs?
[ 0.058030] SCSI subsystem initialized
[ 0.058561] usbcore: registered new interface driver usbfs
[ 0.058622] usbcore: registered new interface driver hub
[ 0.058678] usbcore: registered new device driver usb
[ 0.058838] pps_core: LinuxPPS API ver. 1 registered
[ 0.058848] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti giometti@linux.it
[ 0.058880] PTP clock support registered
[ 0.059208] Advanced Linux Sound Architecture Driver Initialized.
[ 0.059280] workqueue: max_active 576 requested for napi_workq is out of rang e, clamping between 1 and 512
[ 0.060313] clocksource: Switched to clocksource arch_sys_counter
[ 0.065786] thermal_sys: Registered thermal governor 'step_wise'
[ 0.066130] NET: Registered protocol family 2
[ 0.066321] IP idents hash table entries: 16384 (order: 5, 131072 bytes, line ar)
[ 0.067145] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.067176] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[ 0.067248] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.067363] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.067474] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.067538] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[ 0.067759] NET: Registered protocol family 1
[ 0.068548] kvm [1]: Hyp mode initialized successfully
[ 0.069693] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[ 0.075837] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.075994] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.077163] bounce: pool size: 64 pages
[ 0.078268] sun4i-usb-phy 1c13400.phy: failed to get clock usb0_phy
[ 0.080100] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pi not found, using dummy regulator
[ 0.086287] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.092491] loop: module loaded
[ 0.093798] libphy: Fixed MDIO Bus: probed
[ 0.094926] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.094939] ehci-platform: EHCI generic platform driver
[ 0.095437] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.095470] ohci-platform: OHCI generic platform driver
[ 0.095874] usbcore: registered new interface driver usb-storage
[ 0.096116] mousedev: PS/2 mouse device common for all mice
[ 0.096511] i2c /dev entries driver
[ 0.097191] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, now ayout=0)
[ 0.099758] NET: Registered protocol family 10
[ 0.100719] Segment Routing with IPv6
[ 0.100793] NET: Registered protocol family 17
[ 0.100848] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.100855] can: controller area network core (rev 20170425 abi 9)
[ 0.100907] NET: Registered protocol family 29
[ 0.100916] 8021q: 802.1Q VLAN Support v1.8
[ 0.101023] Registering SWP/SWPB emulation handler
[ 0.113033] sun4i-usb-phy 1c13400.phy: Couldn't get regulator usb1_vbus... De ferring probe
[ 0.114690] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pi not found, using dummy regulator
[ 0.116113] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.117522] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator
[ 0.117904] printk: console [ttyS0] disabled
[ 0.138183] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 32, base_baud = 15 00000) is a U6_16550A
[ 0.824490] printk: console [ttyS0] enabled
[ 0.829257] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator
[ 0.836068] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 198
[ 0.842688] sun4i-pinctrl 1c20800.pinctrl: pin-198 (1c28c00.serial) status -5 17
[ 0.849990] sun4i-pinctrl 1c20800.pinctrl: could not request pin 198 (PG6) fr om group PG6 on device 1c20800.pinctrl
[ 0.860509] dw-apb-uart 1c28c00.serial: Error applying setting, reverse thing s back
[ 0.868549] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator
[ 0.875350] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0
[ 0.881801] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -5 17
[ 0.889103] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl
[ 0.899444] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse thi ngs back
[ 0.909286] axp20x-i2c 0-0034: AXP20x variant AXP221 found
[ 0.930557] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-00 34/axp221-pek/input/input0
[ 0.941057] vcc-3v3: supplied by regulator-dummy
[ 0.946794] vdd-cpu: supplied by regulator-dummy
[ 0.952103] vdd-sys: supplied by regulator-dummy
[ 0.957483] dcdc4: supplied by regulator-dummy
[ 0.962458] vcc-dram: supplied by regulator-dummy
[ 0.967373] vcc-gmac-phy: failed to get the current voltage(-517)
[ 0.973501] vcc-gmac-phy: supplied by vcc-3v3
[ 0.978616] dc5ldo: supplied by vcc-dram
[ 0.982947] random: fast init done
[ 0.986508] aldo1: supplied by regulator-dummy
[ 0.991623] vcc-pa: supplied by regulator-dummy
[ 0.996681] avcc: supplied by regulator-dummy
[ 1.002238] eldo1: supplied by regulator-dummy
[ 1.007345] eldo2: supplied by regulator-dummy
[ 1.012460] vdd1v2-sata: supplied by regulator-dummy
[ 1.017907] vcc-wifi-io: Bringing 700000uV into 1800000-1800000uV
[ 1.024916] vcc-wifi-io: supplied by regulator-dummy
[ 1.030368] vcc-wifi: Bringing 700000uV into 3300000-3300000uV
[ 1.036524] vcc-wifi: supplied by regulator-dummy
[ 1.042177] vcc-wifi-2: Bringing 700000uV into 3300000-3300000uV
[ 1.048509] vcc-wifi-2: supplied by regulator-dummy
[ 1.054492] vdd2v5-sata: supplied by regulator-dummy
[ 1.059562] rtc_ldo: supplied by regulator-dummy
[ 1.064969] ldo_io0: supplied by regulator-dummy
[ 1.070216] ldo_io1: supplied by regulator-dummy
[ 1.075968] axp20x-usb-power-supply axp20x-usb-power-supply: DMA mask not set
[ 1.083182] axp20x-i2c 0-0034: AXP20X driver loaded
[ 1.089860] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator
[ 1.099573] sunxi-mmc 1c0f000.mmc: Got CD GPIO
[ 1.140468] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.150509] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq
[ 1.190325] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB, uses new timings mode
[ 1.240327] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, u ses new timings mode
[ 1.271867] 1c28c00.serial: ttyS1 at MMIO 0x1c28c00 (irq = 33, base_baud = 15 00000) is a U6_16550A
[ 1.281527] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found
[ 1.287881] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found
[ 1.293906] dwmac-sun8i 1c50000.ethernet: PTP uses main clock
[ 1.299967] dwmac-sun8i 1c50000.ethernet: Current syscon value is not the def ault 6 (expect 0)
[ 1.308643] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supporte d
[ 1.315870] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supporte d
[ 1.323095] dwmac-sun8i 1c50000.ethernet: COE Type 2
[ 1.328054] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported
[ 1.334844] dwmac-sun8i 1c50000.ethernet: Normal descriptors
[ 1.340504] dwmac-sun8i 1c50000.ethernet: Chain mode enabled
[ 1.346354] libphy: stmmac: probed
[ 1.358740] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 1.367233] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.372828] mmc0: host does not support reading read-only switch, assuming wr ite-enable
[ 1.383246] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 1.388915] mmc0: new high speed SDHC card at address aaaa
[ 1.395920] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
[ 1.401317] ehci-platform 1c19000.usb: EHCI Host Controller
[ 1.406915] ehci-platform 1c19000.usb: new USB bus registered, assigned bus n umber 1
[ 1.414817] ehci-platform 1c19000.usb: irq 26, io mem 0x01c19000
[ 1.425620] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 1.431392] mmcblk0: p1 p2
[ 1.450334] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00
[ 1.456661] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 5.04
[ 1.464948] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 1.472181] usb usb1: Product: EHCI Host Controller
[ 1.477053] usb usb1: Manufacturer: Linux 5.4.172 ehci_hcd
[ 1.482543] usb usb1: SerialNumber: 1c19000.usb
[ 1.487511] hub 1-0:1.0: USB hub found
[ 1.491513] hub 1-0:1.0: 1 port detected
[ 1.496268] ehci-platform 1c1c000.usb: EHCI Host Controller
[ 1.501894] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus n umber 2
[ 1.509764] ehci-platform 1c1c000.usb: irq 28, io mem 0x01c1c000
[ 1.540315] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
[ 1.546590] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 5.04
[ 1.554878] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 1.562104] usb usb2: Product: EHCI Host Controller
[ 1.566976] usb usb2: Manufacturer: Linux 5.4.172 ehci_hcd
[ 1.572464] usb usb2: SerialNumber: 1c1c000.usb
[ 1.577405] hub 2-0:1.0: USB hub found
[ 1.581238] hub 2-0:1.0: 1 port detected
[ 1.585957] ohci-platform 1c19400.usb: Generic Platform OHCI controller
[ 1.592610] ohci-platform 1c19400.usb: new USB bus registered, assigned bus n umber 3
[ 1.600485] ohci-platform 1c19400.usb: irq 27, io mem 0x01c19400
[ 1.633525] mmc2: new DDR MMC card at address 0001
[ 1.639150] mmcblk2: mmc2:0001 8GTF4R 7.28 GiB
[ 1.644208] mmcblk2boot0: mmc2:0001 8GTF4R partition 1 4.00 MiB
[ 1.650631] mmcblk2boot1: mmc2:0001 8GTF4R partition 2 4.00 MiB
[ 1.657373] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.663905] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.670323] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.680716] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.687159] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.693632] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 5.04
[ 1.701918] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 1.709133] usb usb3: Product: Generic Platform OHCI controller
[ 1.715057] usb usb3: Manufacturer: Linux 5.4.172 ohci_hcd
[ 1.720544] usb usb3: SerialNumber: 1c19400.usb
[ 1.725535] hub 3-0:1.0: USB hub found
[ 1.729347] hub 3-0:1.0: 1 port detected
[ 1.734220] ohci-platform 1c1c400.usb: Generic Platform OHCI controller
[ 1.740886] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus n umber 4
[ 1.748758] ohci-platform 1c1c400.usb: irq 29, io mem 0x01c1c400
[ 1.824501] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 5.04
[ 1.832790] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1
[ 1.840004] usb usb4: Product: Generic Platform OHCI controller
[ 1.845929] usb usb4: Manufacturer: Linux 5.4.172 ohci_hcd
[ 1.851417] usb usb4: SerialNumber: 1c1c400.usb
[ 1.856362] hub 4-0:1.0: USB hub found
[ 1.860254] hub 4-0:1.0: 1 port detected
[ 1.864650] hctosys: unable to open rtc device (rtc0)
[ 1.870115] ALSA device list:
[ 1.873100] No soundcards found.
[ 1.880269] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.886637] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ ) flags 0x0 phys_seg 1 prio class 0
[ 1.896817] Buffer I/O error on dev mmcblk2, logical block 0, async page read
[ 1.904261] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.910718] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.917129] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.923563] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.929974] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.936408] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 1.942735] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ ) flags 0x0 phys_seg 1 prio class 0
[ 1.952913] Buffer I/O error on dev mmcblk2, logical block 0, async page read
[ 1.960062] mmcblk2: unable to read partition table
[ 1.976116] VFS: Mounted root (squashfs filesystem) readonly on device 179:2.
[ 1.985420] Freeing unused kernel memory: 2048K
[ 1.993832] mmc1: new high speed SDIO card at address 0001
[ 2.020551] Run /sbin/init as init process
[ 2.693226] init: Console is alive
[ 2.696870] init: - watchdog -
[ 3.904685] kmodloader: loading kernel modules from /etc/modules-boot.d/
[ 4.182935] Key type encrypted registered
[ 4.190647] raid6: using algorithm neonx8 gen() 0 MB/s
[ 4.195790] raid6: .... xor() 0 MB/s, rmw enabled
[ 4.200522] raid6: using neon recovery algorithm
[ 4.210599] xor: measuring software checksum speed
[ 4.310306] arm4regs : 1262.400 MB/sec
[ 4.410292] 8regs : 876.800 MB/sec
[ 4.510290] 32regs : 808.000 MB/sec
[ 4.610291] neon : 1282.800 MB/sec
[ 4.614470] xor: using function: neon (1282.800 MB/sec)
[ 4.638140] Btrfs loaded, crc32c=crc32c-generic
[ 4.647885] ahci-sunxi 1c18000.sata: 1c18000.sata supply target not found, us ing dummy regulator
[ 4.750335] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP _PMP
[ 4.757816] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
[ 4.763705] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0 x1 impl platform mode
[ 4.772668] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
[ 4.781400] scsi host0: ahci-sunxi
[ 4.785219] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x1 00 irq 25
[ 5.130349] ata1: SATA link down (SStatus 0 SControl 300)
[ 5.136396] kmodloader: done loading kernel modules from /etc/modules-boot.d/
[ 5.160540] init: - preinit -
[ 6.416827] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.443475] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.464533] random: jshn: uninitialized urandom read (4 bytes read)
[ 6.580332] dwmac-sun8i 1c50000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8 211E Gigabit Ethernet]
[ 6.590412] dwmac-sun8i 1c50000.ethernet eth0: No Safety Features support fou nd
[ 6.597720] dwmac-sun8i 1c50000.ethernet eth0: No MAC Management Counters ava ilable
[ 6.605380] dwmac-sun8i 1c50000.ethernet eth0: PTP not supported by HW
[ 6.611915] dwmac-sun8i 1c50000.ethernet eth0: configuring for phy/rgmii-id l ink mode
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 10.967279] mount_root: loading kmods from internal overlay
[ 10.992346] kmodloader: loading kernel modules from //etc/modules-boot.d/
[ 11.000667] kmodloader: done loading kernel modules from //etc/modules-boot.d/
[ 11.561665] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.568138] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.574589] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.581014] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.587418] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.593834] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.600137] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0
[ 11.610931] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.617337] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.623763] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.630164] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.636574] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.642980] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.649277] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 11.659445] Buffer I/O error on dev mmcblk2, logical block 0, async page read
[ 11.667455] sunxi-mmc 1c11000.mmc: data error, sending stop command
[ 11.673739] sunxi-mmc 1c11000.mmc: send stop command failed
Plume-yu
commented
2 years ago
反馈bug/问题模板，提建议请删除
1.关于你要提交的问题
Q：是否搜索了issue (使用 "x" 选择) 没有类似的issue
2. 详细叙述
固件正常编译出来了上机跑不起来
(2) 路由器型号和固件版
banana-pi-m2u
(3) 详细日志
U-Boot SPL 2020.04 (Jan 17 2022 - 14:31:40 +0000) DRAM: 2048 MiB Trying to boot from MMC1
U-Boot 2020.04 (Jan 17 2022 - 14:31:40 +0000) Allwinner Technology
CPU: Allwinner R40 (SUN8I 1701) Model: Banana Pi BPI-M2-Ultra I2C: ready DRAM: 2 GiB MMC: Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000' mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1 Loading Environment from FAT... *** Warning - bad CRC, using default environment
In: serial@1c28000 Out: serial@1c28000 Err: serial@1c28000 Net: phy interface7 eth0: ethernet@1c50000 starting USB... Bus usb@1c19000: failed to get usb phy Port not available. Bus usb@1c19400: failed to get usb phy Port not available. Bus usb@1c1c000: failed to get usb phy Port not available. Bus usb@1c1c400: failed to get usb phy Port not available. Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc0 is current device Scanning mmc 0:1... Found U-Boot script /boot.scr 377 bytes read in 2 ms (183.6 KiB/s)
Executing script at 43100000
3272896 bytes read in 149 ms (20.9 MiB/s) 17640 bytes read in 3 ms (5.6 MiB/s)
Booting kernel from Legacy Image at 42000000 ...
Image Name: ARM OpenWrt Linux-5.4.172 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 3272832 Bytes = 3.1 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK
Flattened Device Tree blob at 43000000
Booting using the fdt blob at 0x43000000 Loading Kernel Image Using Device Tree in place at 43000000, end 430074e7
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.172 (yu@yu-n3455) (gcc version 8.4.0 (OpenWrt G CC 8.4.0 r4106-ddb86302d)) #0 SMP Mon Jan 17 14:31:40 2022 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=30c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio n cache [ 0.000000] OF: fdt: Machine model: Banana Pi BPI-M2-Ultra [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: Using PSCI v0.1 Function IDs from DT [ 0.000000] percpu: Embedded 15 pages/cpu s30924 r8192 d22324 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 522560 [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk root=/dev/m mcblk0p2 rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, li near) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 2064616K/2097152K available (6671K kernel code, 426K rwda ta, 1820K rodata, 2048K init, 246K bss, 32536K reserved, 0K cma-reserved, 131070 8K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jif fies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2force probe not set [ 0.000000] random: get_random_bytes called from start_kernel+0x2fc/0x4ac wit h crng_init=0 [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 43980 46511097ns [ 0.000016] Switching to timer-based delay loop, resolution 41ns [ 0.000125] Console: colour dummy device 80x30 [ 0.000175] Calibrating delay loop (skipped), value calculated using timer fr equency.. 48.00 BogoMIPS (lpj=240000) [ 0.000187] pid_max: default: 32768 minimum: 301 [ 0.000357] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linea r) [ 0.000372] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.001259] CPU: Testing write buffer coherency: ok [ 0.001629] /cpus/cpu@0 missing clock-frequency property [ 0.001646] /cpus/cpu@1 missing clock-frequency property [ 0.001660] /cpus/cpu@2 missing clock-frequency property [ 0.001673] /cpus/cpu@3 missing clock-frequency property [ 0.001683] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.002162] Setting up static identity map for 0x40200000 - 0x40200060 [ 0.002272] rcu: Hierarchical SRCU implementation. [ 0.002748] smp: Bringing up secondary CPUs ... [ 0.013454] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.024237] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.034968] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.035052] smp: Brought up 1 node, 4 CPUs [ 0.035069] SMP: Total of 4 processors activated (192.00 BogoMIPS). [ 0.035075] CPU: All CPU(s) started in HYP mode. [ 0.035080] CPU: Virtualization extensions available. [ 0.039530] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.039754] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns [ 0.039774] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.040030] pinctrl core: initialized pinctrl subsystem [ 0.041108] NET: Registered protocol family 16 [ 0.041789] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.042832] No ATAGs? [ 0.058030] SCSI subsystem initialized [ 0.058561] usbcore: registered new interface driver usbfs [ 0.058622] usbcore: registered new interface driver hub [ 0.058678] usbcore: registered new device driver usb [ 0.058838] pps_core: LinuxPPS API ver. 1 registered [ 0.058848] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome tti giometti@linux.it [ 0.058880] PTP clock support registered [ 0.059208] Advanced Linux Sound Architecture Driver Initialized. [ 0.059280] workqueue: max_active 576 requested for napi_workq is out of rang e, clamping between 1 and 512 [ 0.060313] clocksource: Switched to clocksource arch_sys_counter [ 0.065786] thermal_sys: Registered thermal governor 'step_wise' [ 0.066130] NET: Registered protocol family 2 [ 0.066321] IP idents hash table entries: 16384 (order: 5, 131072 bytes, line ar) [ 0.067145] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.067176] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.067248] TCP bind hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.067363] TCP: Hash tables configured (established 8192 bind 8192) [ 0.067474] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.067538] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.067759] NET: Registered protocol family 1 [ 0.068548] kvm [1]: Hyp mode initialized successfully [ 0.069693] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.075837] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.075994] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc. [ 0.077163] bounce: pool size: 64 pages [ 0.078268] sun4i-usb-phy 1c13400.phy: failed to get clock usb0_phy [ 0.080100] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pi not found, using dummy regulator [ 0.086287] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled [ 0.092491] loop: module loaded [ 0.093798] libphy: Fixed MDIO Bus: probed [ 0.094926] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 0.094939] ehci-platform: EHCI generic platform driver [ 0.095437] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 0.095470] ohci-platform: OHCI generic platform driver [ 0.095874] usbcore: registered new interface driver usb-storage [ 0.096116] mousedev: PS/2 mouse device common for all mice [ 0.096511] i2c /dev entries driver [ 0.097191] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, now ayout=0) [ 0.099758] NET: Registered protocol family 10 [ 0.100719] Segment Routing with IPv6 [ 0.100793] NET: Registered protocol family 17 [ 0.100848] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.100855] can: controller area network core (rev 20170425 abi 9) [ 0.100907] NET: Registered protocol family 29 [ 0.100916] 8021q: 802.1Q VLAN Support v1.8 [ 0.101023] Registering SWP/SWPB emulation handler [ 0.113033] sun4i-usb-phy 1c13400.phy: Couldn't get regulator usb1_vbus... De ferring probe [ 0.114690] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pi not found, using dummy regulator [ 0.116113] sun4i-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 0.117522] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-pb not found, using dummy regulator [ 0.117904] printk: console [ttyS0] disabled [ 0.138183] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 32, base_baud = 15 00000) is a U6_16550A [ 0.824490] printk: console [ttyS0] enabled [ 0.829257] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 0.836068] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 198 [ 0.842688] sun4i-pinctrl 1c20800.pinctrl: pin-198 (1c28c00.serial) status -5 17 [ 0.849990] sun4i-pinctrl 1c20800.pinctrl: could not request pin 198 (PG6) fr om group PG6 on device 1c20800.pinctrl [ 0.860509] dw-apb-uart 1c28c00.serial: Error applying setting, reverse thing s back [ 0.868549] sun4i-pinctrl 1c20800.pinctrl: Couldn't get bank PA regulator [ 0.875350] sun4i-pinctrl 1c20800.pinctrl: request() failed for pin 0 [ 0.881801] sun4i-pinctrl 1c20800.pinctrl: pin-0 (1c50000.ethernet) status -5 17 [ 0.889103] sun4i-pinctrl 1c20800.pinctrl: could not request pin 0 (PA0) from group PA0 on device 1c20800.pinctrl [ 0.899444] dwmac-sun8i 1c50000.ethernet: Error applying setting, reverse thi ngs back [ 0.909286] axp20x-i2c 0-0034: AXP20x variant AXP221 found [ 0.930557] input: axp20x-pek as /devices/platform/soc/1c2ac00.i2c/i2c-0/0-00 34/axp221-pek/input/input0 [ 0.941057] vcc-3v3: supplied by regulator-dummy [ 0.946794] vdd-cpu: supplied by regulator-dummy [ 0.952103] vdd-sys: supplied by regulator-dummy [ 0.957483] dcdc4: supplied by regulator-dummy [ 0.962458] vcc-dram: supplied by regulator-dummy [ 0.967373] vcc-gmac-phy: failed to get the current voltage(-517) [ 0.973501] vcc-gmac-phy: supplied by vcc-3v3 [ 0.978616] dc5ldo: supplied by vcc-dram [ 0.982947] random: fast init done [ 0.986508] aldo1: supplied by regulator-dummy [ 0.991623] vcc-pa: supplied by regulator-dummy [ 0.996681] avcc: supplied by regulator-dummy [ 1.002238] eldo1: supplied by regulator-dummy [ 1.007345] eldo2: supplied by regulator-dummy [ 1.012460] vdd1v2-sata: supplied by regulator-dummy [ 1.017907] vcc-wifi-io: Bringing 700000uV into 1800000-1800000uV [ 1.024916] vcc-wifi-io: supplied by regulator-dummy [ 1.030368] vcc-wifi: Bringing 700000uV into 3300000-3300000uV [ 1.036524] vcc-wifi: supplied by regulator-dummy [ 1.042177] vcc-wifi-2: Bringing 700000uV into 3300000-3300000uV [ 1.048509] vcc-wifi-2: supplied by regulator-dummy [ 1.054492] vdd2v5-sata: supplied by regulator-dummy [ 1.059562] rtc_ldo: supplied by regulator-dummy [ 1.064969] ldo_io0: supplied by regulator-dummy [ 1.070216] ldo_io1: supplied by regulator-dummy [ 1.075968] axp20x-usb-power-supply axp20x-usb-power-supply: DMA mask not set [ 1.083182] axp20x-i2c 0-0034: AXP20X driver loaded [ 1.089860] sun4i-pinctrl 1c20800.pinctrl: 1c20800.pinctrl supply vcc-ph not found, using dummy regulator [ 1.099573] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 1.140468] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 1.150509] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq [ 1.190325] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 1.240327] sunxi-mmc 1c11000.mmc: initialized, max. request size: 2048 KB, u ses new timings mode [ 1.271867] 1c28c00.serial: ttyS1 at MMIO 0x1c28c00 (irq = 33, base_baud = 15 00000) is a U6_16550A [ 1.281527] dwmac-sun8i 1c50000.ethernet: IRQ eth_wake_irq not found [ 1.287881] dwmac-sun8i 1c50000.ethernet: IRQ eth_lpi not found [ 1.293906] dwmac-sun8i 1c50000.ethernet: PTP uses main clock [ 1.299967] dwmac-sun8i 1c50000.ethernet: Current syscon value is not the def ault 6 (expect 0) [ 1.308643] dwmac-sun8i 1c50000.ethernet: No HW DMA feature register supporte d [ 1.315870] dwmac-sun8i 1c50000.ethernet: RX Checksum Offload Engine supporte d [ 1.323095] dwmac-sun8i 1c50000.ethernet: COE Type 2 [ 1.328054] dwmac-sun8i 1c50000.ethernet: TX Checksum insertion supported [ 1.334844] dwmac-sun8i 1c50000.ethernet: Normal descriptors [ 1.340504] dwmac-sun8i 1c50000.ethernet: Chain mode enabled [ 1.346354] libphy: stmmac: probed [ 1.358740] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 1.367233] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.372828] mmc0: host does not support reading read-only switch, assuming wr ite-enable [ 1.383246] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 1.388915] mmc0: new high speed SDHC card at address aaaa [ 1.395920] mmcblk0: mmc0:aaaa SL16G 14.8 GiB [ 1.401317] ehci-platform 1c19000.usb: EHCI Host Controller [ 1.406915] ehci-platform 1c19000.usb: new USB bus registered, assigned bus n umber 1 [ 1.414817] ehci-platform 1c19000.usb: irq 26, io mem 0x01c19000 [ 1.425620] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 1.431392] mmcblk0: p1 p2 [ 1.450334] ehci-platform 1c19000.usb: USB 2.0 started, EHCI 1.00 [ 1.456661] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 5.04 [ 1.464948] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 1.472181] usb usb1: Product: EHCI Host Controller [ 1.477053] usb usb1: Manufacturer: Linux 5.4.172 ehci_hcd [ 1.482543] usb usb1: SerialNumber: 1c19000.usb [ 1.487511] hub 1-0:1.0: USB hub found [ 1.491513] hub 1-0:1.0: 1 port detected [ 1.496268] ehci-platform 1c1c000.usb: EHCI Host Controller [ 1.501894] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus n umber 2 [ 1.509764] ehci-platform 1c1c000.usb: irq 28, io mem 0x01c1c000 [ 1.540315] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00 [ 1.546590] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bc dDevice= 5.04 [ 1.554878] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 1.562104] usb usb2: Product: EHCI Host Controller [ 1.566976] usb usb2: Manufacturer: Linux 5.4.172 ehci_hcd [ 1.572464] usb usb2: SerialNumber: 1c1c000.usb [ 1.577405] hub 2-0:1.0: USB hub found [ 1.581238] hub 2-0:1.0: 1 port detected [ 1.585957] ohci-platform 1c19400.usb: Generic Platform OHCI controller [ 1.592610] ohci-platform 1c19400.usb: new USB bus registered, assigned bus n umber 3 [ 1.600485] ohci-platform 1c19400.usb: irq 27, io mem 0x01c19400 [ 1.633525] mmc2: new DDR MMC card at address 0001 [ 1.639150] mmcblk2: mmc2:0001 8GTF4R 7.28 GiB [ 1.644208] mmcblk2boot0: mmc2:0001 8GTF4R partition 1 4.00 MiB [ 1.650631] mmcblk2boot1: mmc2:0001 8GTF4R partition 2 4.00 MiB [ 1.657373] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.663905] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.670323] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.680716] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.687159] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.693632] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 5.04 [ 1.701918] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 1.709133] usb usb3: Product: Generic Platform OHCI controller [ 1.715057] usb usb3: Manufacturer: Linux 5.4.172 ohci_hcd [ 1.720544] usb usb3: SerialNumber: 1c19400.usb [ 1.725535] hub 3-0:1.0: USB hub found [ 1.729347] hub 3-0:1.0: 1 port detected [ 1.734220] ohci-platform 1c1c400.usb: Generic Platform OHCI controller [ 1.740886] ohci-platform 1c1c400.usb: new USB bus registered, assigned bus n umber 4 [ 1.748758] ohci-platform 1c1c400.usb: irq 29, io mem 0x01c1c400 [ 1.824501] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bc dDevice= 5.04 [ 1.832790] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber= 1 [ 1.840004] usb usb4: Product: Generic Platform OHCI controller [ 1.845929] usb usb4: Manufacturer: Linux 5.4.172 ohci_hcd [ 1.851417] usb usb4: SerialNumber: 1c1c400.usb [ 1.856362] hub 4-0:1.0: USB hub found [ 1.860254] hub 4-0:1.0: 1 port detected [ 1.864650] hctosys: unable to open rtc device (rtc0) [ 1.870115] ALSA device list: [ 1.873100] No soundcards found. [ 1.880269] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.886637] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ ) flags 0x0 phys_seg 1 prio class 0 [ 1.896817] Buffer I/O error on dev mmcblk2, logical block 0, async page read [ 1.904261] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.910718] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.917129] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.923563] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.929974] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.936408] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 1.942735] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ ) flags 0x0 phys_seg 1 prio class 0 [ 1.952913] Buffer I/O error on dev mmcblk2, logical block 0, async page read [ 1.960062] mmcblk2: unable to read partition table [ 1.976116] VFS: Mounted root (squashfs filesystem) readonly on device 179:2. [ 1.985420] Freeing unused kernel memory: 2048K [ 1.993832] mmc1: new high speed SDIO card at address 0001 [ 2.020551] Run /sbin/init as init process [ 2.693226] init: Console is alive [ 2.696870] init: - watchdog - [ 3.904685] kmodloader: loading kernel modules from /etc/modules-boot.d/ [ 4.182935] Key type encrypted registered [ 4.190647] raid6: using algorithm neonx8 gen() 0 MB/s [ 4.195790] raid6: .... xor() 0 MB/s, rmw enabled [ 4.200522] raid6: using neon recovery algorithm [ 4.210599] xor: measuring software checksum speed [ 4.310306] arm4regs : 1262.400 MB/sec [ 4.410292] 8regs : 876.800 MB/sec [ 4.510290] 32regs : 808.000 MB/sec [ 4.610291] neon : 1282.800 MB/sec [ 4.614470] xor: using function: neon (1282.800 MB/sec) [ 4.638140] Btrfs loaded, crc32c=crc32c-generic [ 4.647885] ahci-sunxi 1c18000.sata: 1c18000.sata supply target not found, us ing dummy regulator [ 4.750335] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP _PMP [ 4.757816] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1 [ 4.763705] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0 x1 impl platform mode [ 4.772668] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc [ 4.781400] scsi host0: ahci-sunxi [ 4.785219] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x1 00 irq 25 [ 5.130349] ata1: SATA link down (SStatus 0 SControl 300) [ 5.136396] kmodloader: done loading kernel modules from /etc/modules-boot.d/ [ 5.160540] init: - preinit - [ 6.416827] random: jshn: uninitialized urandom read (4 bytes read) [ 6.443475] random: jshn: uninitialized urandom read (4 bytes read) [ 6.464533] random: jshn: uninitialized urandom read (4 bytes read) [ 6.580332] dwmac-sun8i 1c50000.ethernet eth0: PHY [stmmac-0:01] driver [RTL8 211E Gigabit Ethernet] [ 6.590412] dwmac-sun8i 1c50000.ethernet eth0: No Safety Features support fou nd [ 6.597720] dwmac-sun8i 1c50000.ethernet eth0: No MAC Management Counters ava ilable [ 6.605380] dwmac-sun8i 1c50000.ethernet eth0: PTP not supported by HW [ 6.611915] dwmac-sun8i 1c50000.ethernet eth0: configuring for phy/rgmii-id l ink mode Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.967279] mount_root: loading kmods from internal overlay [ 10.992346] kmodloader: loading kernel modules from //etc/modules-boot.d/ [ 11.000667] kmodloader: done loading kernel modules from //etc/modules-boot.d/ [ 11.561665] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.568138] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.574589] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.581014] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.587418] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.593834] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.600137] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 [ 11.610931] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.617337] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.623763] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.630164] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.636574] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.642980] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.649277] blk_update_request: I/O error, dev mmcblk2, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 [ 11.659445] Buffer I/O error on dev mmcblk2, logical block 0, async page read [ 11.667455] sunxi-mmc 1c11000.mmc: data error, sending stop command [ 11.673739] sunxi-mmc 1c11000.mmc: send stop command failed
[ 32.490343] dc5ldo: disabling
A：