liwenjie119
commented
2 years ago cr660x，正常刷入，作为ap，有线可用，无线网无法获取dns，ip直连可用 我再重复测试测试
kernel日志
[ 0.000000] Linux version 5.4.195 (liwenjie@localhost) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r0-04f39ae)) #0 SMP Sun May 29 11:39:21 2022
[ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3
[ 0.000000] printk: bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc)
[ 0.000000] MIPS: machine is Xiaomi Mi Router CR660x
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] VPE topology {2,2} total 4
[ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff]
[ 0.000000] On node 0 totalpages: 65536
[ 0.000000] Normal zone: 576 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 65536 pages, LIFO batch:15
[ 0.000000] percpu: Embedded 14 pages/cpu s27056 r8192 d22096 u57344
[ 0.000000] pcpu-alloc: s27056 r8192 d22096 u57344 alloc=14*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960
[ 0.000000] Kernel command line: console=ttyS0,115200n8 rootfstype=squashfs,jffs2
[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear)
[ 0.000000] Writing ErrCtl register=00056b00
[ 0.000000] Readback ErrCtl register=00056b00
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 249892K/262144K available (6331K kernel code, 269K rwdata, 1320K rodata, 1280K init, 237K bss, 12252K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 256
[ 0.000000] random: get_random_bytes called from start_kernel+0x36c/0x584 with crng_init=0
[ 0.000000] CPU Clock: 880MHz
[ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns
[ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns
[ 0.007805] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688)
[ 0.073978] pid_max: default: 32768 minimum: 301
[ 0.078775] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.085975] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
[ 0.096550] rcu: Hierarchical SRCU implementation.
[ 0.101895] smp: Bringing up secondary CPUs ...
[ 3.284789] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 3.284800] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 3.284812] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 3.284920] CPU1 revision is: 0001992f (MIPS 1004Kc)
[ 0.166692] Synchronize counters for CPU 1: done.
[ 3.378128] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 3.378136] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 3.378144] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 3.378200] CPU2 revision is: 0001992f (MIPS 1004Kc)
[ 0.257450] Synchronize counters for CPU 2: done.
[ 3.465483] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[ 3.465491] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 3.465499] MIPS secondary cache 256kB, 8-way, linesize 32 bytes.
[ 3.465566] CPU3 revision is: 0001992f (MIPS 1004Kc)
[ 0.342638] Synchronize counters for CPU 3: done.
[ 0.372507] smp: Brought up 1 node, 4 CPUs
[ 0.381421] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.391218] futex hash table entries: 1024 (order: 3, 32768 bytes, linear)
[ 0.398217] pinctrl core: initialized pinctrl subsystem
[ 0.404969] NET: Registered protocol family 16
[ 0.422077] FPU Affinity set after 11720 emulations
[ 0.440041] random: fast init done
[ 0.440085] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512
[ 0.454740] clocksource: Switched to clocksource GIC
[ 0.461322] thermal_sys: Registered thermal governor 'step_wise'
[ 0.461827] NET: Registered protocol family 2
[ 0.472242] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.481314] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear)
[ 0.489634] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear)
[ 0.497277] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.504336] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.510783] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.517255] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.524388] NET: Registered protocol family 1
[ 0.528700] PCI: CLS 0 bytes, default 32
[ 0.764662] 4 CPUs re-calibrate udelay(lpj = 2924544)
[ 0.771372] workingset: timestamp_bits=14 max_order=16 bucket_order=2
[ 0.789445] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.795219] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.808721] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.814478] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.820354] mt7621_gpio 1e000600.gpio: registering 32 gpios
[ 0.826829] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled
[ 0.834385] printk: console [ttyS0] disabled
[ 0.838673] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A
[ 0.847651] printk: console [ttyS0] enabled
[ 0.855905] printk: bootconsole [early0] disabled
[ 0.867558] mt7621-nand 1e003000.nand: Using programmed access timing: 31c07388
[ 0.875119] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1
[ 0.881439] nand: ESMT PSU1GA30DT
[ 0.884768] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.892311] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits
[ 0.898862] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[ 0.906154] mt7621-nand 1e003000.nand: Using programmed access timing: 21005134
[ 0.913430] Scanning device for bad blocks
[ 2.887445] 8 fixed-partitions partitions found on MTD device mt7621-nand
[ 2.894202] Creating 8 MTD partitions on "mt7621-nand":
[ 2.899424] 0x000000000000-0x000000080000 : "Bootloader"
[ 2.906097] 0x000000080000-0x0000000c0000 : "Nvram"
[ 2.912209] 0x0000000c0000-0x000000100000 : "Bdata"
[ 2.918237] 0x000000100000-0x000000180000 : "Factory"
[ 2.924386] 0x000000180000-0x0000001c0000 : "crash"
[ 2.930408] 0x0000001c0000-0x000000200000 : "crash_log"
[ 2.936745] 0x000000200000-0x000000600000 : "kernel"
[ 2.942793] 0x000000600000-0x000007f80000 : "ubi"
[ 2.951684] [mtk_hw_init] reset_lock:0, force:0
[ 2.956243] [mtk_hw_init] execute fe cold reset
[ 2.972405] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 2.980301] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22
[ 2.988657] (unnamed net_device) (dummy): netif_napi_add() called with weight 256
[ 2.998399] mt7621-pci 1e140000.pcie: Parsing DT failed
[ 3.006200] NET: Registered protocol family 10
[ 3.012115] Segment Routing with IPv6
[ 3.015952] NET: Registered protocol family 17
[ 3.020481] Bridge firewalling registered
[ 3.024757] 8021q: 802.1Q VLAN Support v1.8
[ 3.032387] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module
[ 3.052294] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY]
[ 3.062032] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY]
[ 3.071715] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY]
[ 3.081727] mt7530 mdio-bus:1f wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY]
[ 3.091527] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode
[ 3.102661] DSA: tree 0 setup
[ 3.105971] rt2880-pinmux pinctrl: pcie is already enabled
[ 3.111573] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1)
[ 3.119173] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0)
[ 3.126618] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22
[ 3.233739] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz
[ 3.239318] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz
[ 3.344777] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK)
[ 3.351709] mt7621-pci 1e140000.pcie: PCIE0 enabled
[ 3.356574] mt7621-pci 1e140000.pcie: PCIE1 enabled
[ 3.361434] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002
[ 3.370894] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00
[ 3.377247] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff]
[ 3.384089] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff]
[ 3.390945] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 3.396459] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400
[ 3.402470] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 3.408732] pci 0000:00:00.0: reg 0x14: [mem 0x60600000-0x6060ffff]
[ 3.415053] pci 0000:00:00.0: supports D1
[ 3.419044] pci 0000:00:00.0: PME# supported from D0 D1 D3hot
[ 3.425154] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400
[ 3.431161] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff]
[ 3.437425] pci 0000:00:01.0: reg 0x14: [mem 0x60610000-0x6061ffff]
[ 3.443721] pci 0000:00:01.0: supports D1
[ 3.447724] pci 0000:00:01.0: PME# supported from D0 D1 D3hot
[ 3.455087] pci 0000:01:00.0: [14c3:7916] type 00 class 0x000280
[ 3.461130] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 3.468352] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 3.475569] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 3.482878] pci 0000:01:00.0: supports D1 D2
[ 3.487139] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 3.493759] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 3.508936] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 3.514146] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff]
[ 3.520230] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 3.527004] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 3.534197] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 3.541009] pci 0000:02:00.0: [14c3:7915] type 00 class 0x000280
[ 3.547064] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 3.554267] pci 0000:02:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 3.561482] pci 0000:02:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 3.568805] pci 0000:02:00.0: supports D1 D2
[ 3.573055] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 3.579684] pci 0000:02:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:01.0 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[ 3.594914] pci 0000:00:01.0: PCI bridge to [bus 02-ff]
[ 3.600127] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff]
[ 3.606207] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 3.612965] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 3.620168] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02
[ 3.626814] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000]
[ 3.633396] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000]
[ 3.640341] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000]
[ 3.646937] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000]
[ 3.653870] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff]
[ 3.660642] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref]
[ 3.667853] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff]
[ 3.674611] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x605fffff pref]
[ 3.681815] pci 0000:00:00.0: BAR 1: assigned [mem 0x60600000-0x6060ffff]
[ 3.688593] pci 0000:00:01.0: BAR 1: assigned [mem 0x60610000-0x6061ffff]
[ 3.695367] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff]
[ 3.702123] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff]
[ 3.708903] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref]
[ 3.716639] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref]
[ 3.724357] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref]
[ 3.732088] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 3.737045] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff]
[ 3.743803] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff]
[ 3.750572] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref]
[ 3.757783] pci 0000:02:00.0: BAR 0: assigned [mem 0x60400000-0x604fffff 64bit pref]
[ 3.765519] pci 0000:02:00.0: BAR 2: assigned [mem 0x60500000-0x60503fff 64bit pref]
[ 3.773238] pci 0000:02:00.0: BAR 4: assigned [mem 0x60504000-0x60504fff 64bit pref]
[ 3.780968] pci 0000:00:01.0: PCI bridge to [bus 02]
[ 3.785923] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff]
[ 3.792680] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff]
[ 3.799454] pci 0000:00:01.0: bridge window [mem 0x60400000-0x605fffff pref]
[ 3.807224] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx
[ 3.808358] UBI: auto-attach mtd7
[ 3.817629] ubi0: attaching mtd7
[ 5.071284] ubi0: scanning is finished
[ 5.092637] ubi0: attached mtd7 (name "ubi", size 121 MiB)
[ 5.098143] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 5.105003] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 5.111756] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 5.118694] ubi0: good PEBs: 972, bad PEBs: 0, corrupted PEBs: 0
[ 5.124672] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128
[ 5.131880] ubi0: max/mean erase counter: 8/5, WL threshold: 4096, image sequence number: 1640453085
[ 5.140978] ubi0: available PEBs: 0, total reserved PEBs: 972, PEBs reserved for bad PEB handling: 20
[ 5.150191] ubi0: background thread "ubi_bgt0d" started, PID 460
[ 5.154243] block ubiblock0_0: created from ubi0:0(rootfs)
[ 5.161720] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem
[ 5.168676] hctosys: unable to open rtc device (rtc0)
[ 5.181582] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
[ 5.193186] Freeing unused kernel memory: 1280K
[ 5.197741] This architecture does not have kernel memory protection.
[ 5.204149] Run /sbin/init as init process
[ 6.510235] init: Console is alive
[ 6.513971] init: - watchdog -
[ 8.313001] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 8.649636] usbcore: registered new interface driver usbfs
[ 8.655263] usbcore: registered new interface driver hub
[ 8.660650] usbcore: registered new device driver usb
[ 8.668276] exfat: module is from the staging directory, the quality is unknown, you have been warned.
[ 8.679360] exFAT: Version 1.3.0
[ 8.718590] SCSI subsystem initialized
[ 8.731883] usbcore: registered new interface driver usb-storage
[ 8.738638] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 8.755182] init: - preinit -
[ 11.524051] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 11.532574] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 11.541086] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.351949] random: jshn: uninitialized urandom read (4 bytes read)
[ 12.428664] random: jshn: uninitialized urandom read (4 bytes read)
[ 12.472704] random: jshn: uninitialized urandom read (4 bytes read)
[ 16.212492] mount_root: loading kmods from internal overlay
[ 16.265703] kmodloader: loading kernel modules from //etc/modules-boot.d/*
[ 16.275238] kmodloader: done loading kernel modules from //etc/modules-boot.d/*
[ 17.150271] block: attempting to load /etc/config/fstab
[ 17.159232] block: unable to load configuration (fstab: Entry not found)
[ 17.166171] block: no usable configuration
[ 17.173395] UBIFS (ubi0:1): Mounting in unauthenticated mode
[ 17.179304] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 597
[ 17.261132] UBIFS (ubi0:1): recovery needed
[ 17.447414] UBIFS (ubi0:1): recovery completed
[ 17.452026] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data"
[ 17.459845] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 17.469728] UBIFS (ubi0:1): FS size: 77963264 bytes (74 MiB, 614 LEBs), journal size 3936256 bytes (3 MiB, 31 LEBs)
[ 17.480124] UBIFS (ubi0:1): reserved for root: 3682397 bytes (3596 KiB)
[ 17.486724] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 8FB01538-6229-47E4-A86D-4F9B62C72A77, small LPT model
[ 17.506470] mount_root: loading kmods from internal overlay
[ 17.557568] kmodloader: loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 17.569171] kmodloader: done loading kernel modules from /tmp/overlay/upper/etc/modules-boot.d/*
[ 17.899126] block: attempting to load /etc/config/fstab
[ 17.904550] block: unable to load configuration (fstab: Entry not found)
[ 17.911417] block: no usable configuration
[ 17.919283] mount_root: switching to ubifs overlay
[ 17.943547] urandom-seed: Seeding with /etc/urandom.seed
[ 18.200861] procd: - early -
[ 18.203972] procd: - watchdog -
[ 18.954914] procd: - watchdog -
[ 19.142278] procd: - ubus -
[ 19.551519] procd: - init -
[ 21.434775] kmodloader: loading kernel modules from /etc/modules.d/*
[ 21.539927] NET: Registered protocol family 38
[ 21.571893] NET: Registered protocol family 15
[ 21.580604] Initializing XFRM netlink socket
[ 21.619486] tun: Universal TUN/TAP device driver, 1.6
[ 21.649381] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 21.748470] cryptodev: driver 1.12 loaded.
[ 21.759954] mediatek_soc_hnat 1e100000.hnat: wan = wan
[ 21.765203] mediatek_soc_hnat 1e100000.hnat: lan = lan
[ 21.770338] mediatek_soc_hnat 1e100000.hnat: ppd = lan
[ 21.775508] mediatek_soc_hnat 1e100000.hnat: gmac num = 1
[ 21.780893] mediatek_soc_hnat 1e100000.hnat: wan dsa port = 4
[ 21.786648] mediatek_soc_hnat 1e100000.hnat: ppe num = 1
[ 21.792336] mediatek_soc_hnat 1e100000.hnat: ext devices = apcli0
[ 21.798452] mediatek_soc_hnat 1e100000.hnat: ext devices = apclii0
[ 21.804611] mediatek_soc_hnat 1e100000.hnat: ext devices = apclix0
[ 21.810797] mediatek_soc_hnat 1e100000.hnat: ext devices = ra0
[ 21.816636] mediatek_soc_hnat 1e100000.hnat: ext devices = rai0
[ 21.822539] mediatek_soc_hnat 1e100000.hnat: ext devices = rax0
[ 21.828471] mediatek_soc_hnat 1e100000.hnat: ext devices = wlan0
[ 21.834455] mediatek_soc_hnat 1e100000.hnat: ext devices = wlan1
[ 21.844492] mediatek_soc_hnat 1e100000.hnat: PPE0 entry number = 16384
[ 21.864088] mediatek_soc_hnat 1e100000.hnat: PPE0 hwnat start
[ 21.869998] hnat roaming work enable
[ 21.888940] Loading modules backported from Linux version v5.15.8-0-g43e577d7a2cb
[ 21.896509] Backport generated by backports.git v5.15.8-1-0-g83f664bb
[ 21.912047] mtk-eip93 1e004000.crypto: EIP93 Crypto Engine Initialized.
[ 22.045785] ntfs3: Index binary search
[ 22.049539] ntfs3: Hot fix free clusters
[ 22.053438] ntfs3: Max link count 1024
[ 22.057199] ntfs3: Activated 32 bits per cluster
[ 22.070725] appfilter version:5.0.1
[ 22.074281] open feature file failed
[ 22.077870] error, feature buf is null
[ 22.081603] load feature failed
[ 22.315784] usbcore: registered new interface driver ums-alauda
[ 22.324256] usbcore: registered new interface driver ums-cypress
[ 22.332787] usbcore: registered new interface driver ums-datafab
[ 22.341216] usbcore: registered new interface driver ums-freecom
[ 22.349769] usbcore: registered new interface driver ums-isd200
[ 22.358397] usbcore: registered new interface driver ums-jumpshot
[ 22.366911] usbcore: registered new interface driver ums-karma
[ 22.375838] usbcore: registered new interface driver ums-sddr09
[ 22.384276] usbcore: registered new interface driver ums-sddr55
[ 22.393108] usbcore: registered new interface driver ums-usbat
[ 22.458470] xt_time: kernel timezone is -0000
[ 22.588003] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23
[ 22.593445] pci 0000:00:00.0: enabling device (0006 -> 0007)
[ 22.599182] mt7915e_hif 0000:01:00.0: enabling device (0000 -> 0002)
[ 22.606181] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24
[ 22.611657] pci 0000:00:01.0: enabling device (0006 -> 0007)
[ 22.617427] mt7915e 0000:02:00.0: enabling device (0000 -> 0002)
[ 22.789697] mt7915e 0000:02:00.0: HW/SW Version: 0x8a108a10, Build Time: 20201105222230a
[ 22.789697]
[ 23.311335] mt7915e 0000:02:00.0: WM Firmware Version: ____000000, Build Time: 20201105222304
[ 23.350881] mt7915e 0000:02:00.0: WA Firmware Version: DEV_000000, Build Time: 20201105222323
[ 25.754878] crng init done
[ 25.757605] random: 7 urandom warning(s) missed due to ratelimiting
[ 28.776717] PPP generic driver version 2.4.2
[ 28.783639] PPP MPPE Compression module registered
[ 28.790474] NET: Registered protocol family 24
[ 28.801445] wireguard: WireGuard 1.0.0 loaded. See www.wireguard.com for information.
[ 28.809349] wireguard: Copyright (C) 2015-2019 Jason A. Donenfeld . All Rights Reserved.
[ 28.834653] appfilter version:5.0.1
[ 28.838445] open feature file failed
[ 28.842030] error, feature buf is null
[ 28.845788] load feature failed
[ 28.975515] kmodloader: 1 module could not be probed
[ 28.980921] kmodloader: - oaf - 0
[ 30.532876] mtk_soc_eth 1e100000.ethernet eth0: TX vlan offload cannot be enabled when dsa is attached.
[ 30.545003] mtk_soc_eth 1e100000.ethernet eth0: TX vlan offload cannot be enabled when dsa is attached.
[ 42.309668] mtk_soc_eth 1e100000.ethernet eth0: Link is Down
[ 42.353273] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode
[ 42.361532] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 42.370095] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 42.380389] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode
[ 42.387594] 8021q: adding VLAN 0 to HW filter on device lan1
[ 42.396969] br-lan: port 1(lan1) entered blocking state
[ 42.402219] br-lan: port 1(lan1) entered disabled state
[ 42.408354] device lan1 entered promiscuous mode
[ 42.413062] device eth0 entered promiscuous mode
[ 42.447034] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode
[ 42.454233] 8021q: adding VLAN 0 to HW filter on device lan2
[ 42.464679] br-lan: port 2(lan2) entered blocking state
[ 42.469994] br-lan: port 2(lan2) entered disabled state
[ 42.477097] device lan2 entered promiscuous mode
[ 42.496389] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode
[ 42.503588] 8021q: adding VLAN 0 to HW filter on device lan3
[ 42.513839] br-lan: port 3(lan3) entered blocking state
[ 42.519150] br-lan: port 3(lan3) entered disabled state
[ 42.526461] device lan3 entered promiscuous mode
[ 42.556163] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode
[ 42.563330] 8021q: adding VLAN 0 to HW filter on device wan
[ 46.525411] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 46.588224] extif_set_dev(wlan0)
[ 46.592344] br-lan: port 1(lan1) entered blocking state
[ 46.597731] br-lan: port 1(lan1) entered forwarding state
[ 46.604411] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 46.606295] mt7530 mdio-bus:1f lan2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 46.617085] br-lan: port 4(wlan0) entered blocking state
[ 46.623658] br-lan: port 4(wlan0) entered disabled state
[ 46.629838] device wlan0 entered promiscuous mode
[ 46.635414] br-lan: port 2(lan2) entered blocking state
[ 46.640716] br-lan: port 2(lan2) entered forwarding state
[ 46.667099] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 46.673943] br-lan: port 4(wlan0) entered blocking state
[ 46.679387] br-lan: port 4(wlan0) entered forwarding state
[ 46.687400] mt7530 mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 46.696121] br-lan: port 3(lan3) entered blocking state
[ 46.701469] br-lan: port 3(lan3) entered forwarding state
[ 46.930636] extif_set_dev(wlan1)
[ 46.937889] br-lan: port 5(wlan1) entered blocking state
[ 46.943256] br-lan: port 5(wlan1) entered disabled state
[ 46.950888] device wlan1 entered promiscuous mode
[ 46.956186] br-lan: port 5(wlan1) entered blocking state
[ 46.961522] br-lan: port 5(wlan1) entered forwarding state
[ 47.547233] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready
[ 47.584908] mediatek_soc_hnat 1e100000.hnat: hnat_ipv6_get_nexthop:No neigh (daddr=ff02:0000:0000:0000:0000:0000:0000:0016)
[ 62.257048] appfilter version:5.0.1
[ 62.267306] init oaf sysctl...ok
[ 62.997098] recv user msg
[ 62.999741] oaf msg handle, action = 0
[ 63.003509] module init.........
Hiyajomaho-num9
triatomic
NagaseKouichi
chobitsos
aiamadeus
britneyjeanspears
uniessey
misaka36
feng310
Stkrx
solarflows
eva2021hd
MageDelfador
VirtualboxWu
asiaon123
hcwang
Kuron88
windybird
modelsun
q397333
wuzhuang123
Weibin74
让大家久等了，首先非常感谢 @MeIsReallyBa 大佬带我玩。想必有些人已经看到恩山上大佬发的帖子了，但要让版本号党失望的是我并没有拿大佬已经搞好的 5.10 内核+ mt7621 sdk 来做[1] 。 此套代码基于 mtk 前些天刚放出的 mtk 820/830 开源代 (kernel 5.4)，并成功移植到了 mt7621 5.4 内核上。这套代码有个优点就是功能实现都集中在相关驱动里面 [2] (看注释)，不需要更改内核其它地方，整体驱动部分也更为简洁。还有个考虑就是不可能所有设备都改回 switch，所以 dsa hwnat 也是要尽量实现的[3]。移植过程中看到的几个 kernel panic 无限重启问题我均已修复，所以大家不必过于担心测试的时候路由器炸了（xD
测试源码地址：https://github.com/AmadeusGhost/lede/tree/ramips
测试要求：
注：
这是你们能做的：
暂时没想到这是你们不能做的：