新三能获取到IP，但登录不了界面bad gateway，

反馈bug/问题模板，提建议请删除

1.关于你要提交的问题

Q：是否搜索了issue (使用 "x" 选择)

[x] 没有类似的issue

2. 详细叙述

(1) 具体问题

刷新页面无限[ 83.350283] jffs2: warning: (4496) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76

登录IP 显示 bad gateway

The process did not produce any response 编译了2次都是一样的情况，

(2) 路由器型号和固件版本

新三 D2 A：

(3) 详细日志

DRAM: 512MB Platform: MediaTek MT7621A ver 1, eco 3 Board: Newifi D2 Clocks: CPU: 880MHz, DDR: 1040MHz, Bus: 220MHz, Ref: 40MHz Flash: Winbond W25Q256 (32MB) on mt7621-spi.0 rt2880-eth: MAC address from EEPROM is invalid, using default settings. rt2880-eth: Using MAC address 00:0c:43:00:00:01 eth0: MediaTek MT7530 Gigabit switch

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 2 Autoboot aborted due to button press.

Starting breed built-in shell

breed> Erase completed. Upgrade completed. Rebooting in 2 seconds ... Resetting ...

Network started on eth0, inet addr 192.168.1.1, netmask 255.255.255.0

Press any key to interrupt autoboot ... 0

Trying to boot firmware from 0x00050000 in flash bank 0 ... Reading data into memory ... U-Boot firmware image header detected. Image Name: MIPS OpenWrt Linux-5.4.195 Data Size: 2539494 Bytes Load Address: 80001000 Entry Point: 80001000 Flushing cache ... done.

Starting kernel at 0x80001000...

[ 0.000000] Linux version 5.4.195 (bbb@ubuntu) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r4479-2a91c7245)) #0 SMP Thu Jun 9 15:18:30 2022 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Newifi-D2 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem [mem 0x0000000010000000-0x0000000023ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000001bffffff] [ 0.000000] node 0: [mem 0x0000000020000000-0x0000000023ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000023ffffff] [ 0.000000] percpu: Embedded 14 pages/cpu s26992 r8192 d22160 u57344 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130496 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00031840 [ 0.000000] Readback ErrCtl register=00031840 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 509412K/524288K available (6147K kernel code, 255K rwdata, 1292K rodata, 1252K init, 238K bss, 14876K reserved, 0K cma-reserved, 262144K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x36c/0x584 with crng_init=0 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.000009] sched_clock: 32 bits at 440MHz, resolution 2ns, wraps every 4880645118ns [ 0.007818] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.073976] pid_max: default: 32768 minimum: 301 [ 0.078786] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.085986] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.096676] rcu: Hierarchical SRCU implementation. [ 0.102044] smp: Bringing up secondary CPUs ... [ 0.530273] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.530283] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.530296] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.530409] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.166838] Synchronize counters for CPU 1: done. [ 9.680414] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 9.680424] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 9.680432] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 9.680490] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.257620] Synchronize counters for CPU 2: done. [ 3.318209] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 3.318217] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 3.318225] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 3.318292] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.342805] Synchronize counters for CPU 3: done. [ 0.372678] smp: Brought up 1 node, 4 CPUs [ 0.381391] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.391163] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.398255] pinctrl core: initialized pinctrl subsystem [ 0.405220] NET: Registered protocol family 16 [ 0.415530] sysfs: cannot create duplicate filename '/bus/platform/devices/1e000000.syscon' [ 0.423818] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.195 #0 [ 0.429741] Stack : 807b3e18 80080504 80710000 80711814 80780000 807117dc 80710678 8fc41c34 [ 0.438027] 808c0000 8fc383a8 8075cd63 8069fb84 00000001 00000001 8fc41bd8 a9ca3092 [ 0.446324] 00000000 00000000 80900000 00000000 00000030 00000047 342e3520 3539312e [ 0.454618] 00000000 00000000 00000000 0006778a 00000000 80780000 00000000 8fcd9000 [ 0.462913] 00000001 00000000 00000000 00000000 00000003 00000010 00000004 808c0004 [ 0.471206] ... [ 0.473627] Call Trace: [ 0.476082] [<8000ce5c>] show_stack+0x30/0x100 [ 0.480476] [<805de95c>] dump_stack+0xa4/0xdc [ 0.484785] [<802072b0>] sysfs_warn_dup+0x64/0x80 [ 0.489450] [<80207724>] sysfs_do_create_link_sd.isra.2+0xc8/0x118 [ 0.495594] [<803a3c38>] bus_add_device+0x68/0x150 [ 0.500335] [<803a0a18>] device_add+0x3a0/0x60c [ 0.504836] [<804390e0>] of_platform_device_create_pdata+0xb4/0x10c [ 0.511047] [<80439278>] of_platform_bus_create+0x134/0x224 [ 0.516572] [<804394e4>] of_platform_populate+0x78/0xec [ 0.521780] [<8078aa10>] __dt_register_buses+0xbc/0xec [ 0.526854] [<80789cb0>] plat_of_setup+0x1c/0x34 [ 0.531437] [<800015f8>] do_one_initcall+0x7c/0x1dc [ 0.536271] [<80787f0c>] kernel_init_freeable+0x1ec/0x2d0 [ 0.541650] [<805fa7a8>] kernel_init+0x10/0xf8 [ 0.546034] [<800070d8>] ret_from_kernel_thread+0x14/0x1c [ 0.560620] sysfs: cannot create duplicate filename '/bus/platform/devices/1e000000.syscon' [ 0.568875] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.4.195 #0 [ 0.574825] Stack : 807b3e50 80080504 80710000 80711814 80780000 807117dc 80710678 8fc41c54 [ 0.583115] 808c0000 8fc383a8 8075cd63 8069fb84 00000000 00000001 8fc41bf8 a9ca3092 [ 0.591409] 00000000 00000000 80900000 00000000 00000030 00000060 342e3520 3539312e [ 0.599704] 00000000 00000000 00000000 0008ae2b 00000000 80780000 00000000 8fcd9000 [ 0.607998] 00000001 00000000 00000000 00000000 00000003 00000010 00000000 808c0000 [ 0.616292] ... [ 0.618715] Call Trace: [ 0.621168] [<8000ce5c>] show_stack+0x30/0x100 [ 0.625558] [<805de95c>] dump_stack+0xa4/0xdc [ 0.629872] [<802072b0>] sysfs_warn_dup+0x64/0x80 [ 0.634530] [<80207724>] sysfs_do_create_link_sd.isra.2+0xc8/0x118 [ 0.640679] [<803a3c38>] bus_add_device+0x68/0x150 [ 0.645415] [<803a0a18>] device_add+0x3a0/0x60c [ 0.649923] [<804390e0>] of_platform_device_create_pdata+0xb4/0x10c [ 0.656130] [<80439278>] of_platform_bus_create+0x134/0x224 [ 0.661659] [<804394e4>] of_platform_populate+0x78/0xec [ 0.666869] [<807a2abc>] of_platform_default_populate_init+0xac/0xcc [ 0.673150] [<800015f8>] do_one_initcall+0x7c/0x1dc [ 0.677998] [<80787f0c>] kernel_init_freeable+0x1ec/0x2d0 [ 0.683358] [<805fa7a8>] kernel_init+0x10/0xf8 [ 0.687751] [<800070d8>] ret_from_kernel_thread+0x14/0x1c [ 0.709959] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.721433] clocksource: Switched to clocksource GIC [ 0.728362] NET: Registered protocol family 2 [ 0.732816] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.740654] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.748992] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.756744] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.763831] TCP: Hash tables configured (established 2048 bind 2048) [ 0.770260] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.776762] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.783938] NET: Registered protocol family 1 [ 0.788231] PCI: CLS 0 bytes, default 32 [ 1.031381] 4 CPUs re-calibrate udelay(lpj = 2924544) [ 1.038323] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 1.045364] random: fast init done [ 1.058129] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.063930] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 1.075566] bounce: pool size: 64 pages [ 1.080806] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.086657] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.092525] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 1.098869] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 1.106715] printk: console [ttyS0] disabled [ 1.110979] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 1.120008] printk: console [ttyS0] enabled [ 1.120008] printk: console [ttyS0] enabled [ 1.128267] printk: bootconsole [early0] disabled [ 1.128267] printk: bootconsole [early0] disabled [ 1.140717] spi-mt7621 1e000b00.spi: sys_freq: 220000000 [ 1.155626] spi-nor spi0.0: w25q256 (32768 Kbytes) [ 1.160471] 4 fixed-partitions partitions found on MTD device spi0.0 [ 1.166810] Creating 4 MTD partitions on "spi0.0": [ 1.171616] 0x000000000000-0x000000030000 : "u-boot" [ 1.177780] 0x000000030000-0x000000040000 : "u-boot-env" [ 1.184337] 0x000000040000-0x000000050000 : "factory" [ 1.190522] 0x000000050000-0x000002000000 : "firmware" [ 1.197108] 2 uimage-fw partitions found on MTD device firmware [ 1.203085] Creating 2 MTD partitions on "firmware": [ 1.208043] 0x000000000000-0x00000026c026 : "kernel" [ 1.214322] 0x00000026c026-0x000001fb0000 : "rootfs" [ 1.220504] mtd: device 5 (rootfs) set to be root filesystem [ 1.226288] 1 squashfs-split partitions found on MTD device rootfs [ 1.232486] 0x000001f60000-0x000001fb0000 : "rootfs_data" [ 2.717332] ralink_soc_eth 1e100000.ethernet: loaded mt7530 driver [ 2.724445] ralink_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22 [ 2.735377] mt7621-pci 1e140000.pcie: Parsing DT failed [ 2.743398] NET: Registered protocol family 10 [ 2.749359] Segment Routing with IPv6 [ 2.753236] NET: Registered protocol family 17 [ 2.757974] 8021q: 802.1Q VLAN Support v1.8 [ 2.766214] gpio-export gpio_export: 1 gpio(s) exported [ 2.771887] rt2880-pinmux pinctrl: pcie is already enabled [ 2.777514] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 2.785118] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 2.792587] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22 [ 2.899772] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 2.905354] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 3.010861] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 3.017813] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 3.022689] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 3.027551] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 3.037037] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 3.043415] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 3.050260] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 3.057128] pci_bus 0000:00: root bus resource [bus 00-ff] [ 3.062657] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 3.068670] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 3.074931] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 3.081243] pci 0000:00:00.0: supports D1 [ 3.085257] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 3.091483] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 3.097495] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 3.103756] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 3.110053] pci 0000:00:01.0: supports D1 [ 3.114064] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 3.121310] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.129327] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.137553] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [ 3.143626] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 3.150420] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 3.157215] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 3.164815] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 3.170028] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 3.176125] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 3.182915] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 3.190112] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 3.196971] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000 [ 3.203034] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 3.209409] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 3.216993] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 3.222237] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 3.228304] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 3.235080] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref] [ 3.242299] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 3.248936] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 3.255539] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.262496] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 3.269079] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 3.276030] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 3.282816] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 3.290007] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 3.296785] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 3.304002] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 3.310765] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 3.317549] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 3.324334] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 3.331101] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 3.338409] pci 0000:01:00.0: BAR 6: assigned [mem 0x60100000-0x6010ffff pref] [ 3.345624] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.350568] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 3.357344] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 3.364127] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 3.371324] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff] [ 3.378104] pci 0000:00:01.0: PCI bridge to [bus 02] [ 3.383071] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 3.389829] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 3.396604] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 3.404671] hctosys: unable to open rtc device (rtc0) [ 3.415407] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 3.427371] Freeing unused kernel memory: 1252K [ 3.431951] This architecture does not have kernel memory protection. [ 3.438360] Run /sbin/init as init process [ 4.532091] init: Console is alive [ 4.535872] init: - watchdog - [ 4.946426] ralink_soc_eth 1e100000.ethernet eth0: port 1 link up [ 6.205076] kmodloader: loading kernel modules from /etc/modules-boot.d/ [ 6.594886] usbcore: registered new interface driver usbfs [ 6.600504] usbcore: registered new interface driver hub [ 6.605959] usbcore: registered new device driver usb [ 6.623409] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vbus not found, using dummy regulator [ 6.632200] xhci-mtk 1e1c0000.xhci: 1e1c0000.xhci supply vusb33 not found, using dummy regulator [ 6.641155] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 6.646496] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 6.661606] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 6.670781] xhci-mtk 1e1c0000.xhci: irq 20, io mem 0x1e1c0000 [ 6.677914] hub 1-0:1.0: USB hub found [ 6.681816] hub 1-0:1.0: 2 ports detected [ 6.686551] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 6.691925] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 6.699391] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 6.705964] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.715040] hub 2-0:1.0: USB hub found [ 6.718870] hub 2-0:1.0: 1 port detected [ 6.732250] kmodloader: done loading kernel modules from /etc/modules-boot.d/ [ 6.751866] init: - preinit - [ 8.346272] crng init done [ 8.818094] ralink_soc_eth 1e100000.ethernet: PPE started Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level sendto(): Network unreachable sendto(): Network unreachable [ 16.326694] mount_root: loading kmods from internal overlay [ 16.364964] kmodloader: loading kernel modules from //etc/modules-boot.d/ [ 16.373981] kmodloader: done loading kernel modules from //etc/modules-boot.d/ [ 16.598640] block: attempting to load /etc/config/fstab [ 16.607692] block: unable to load configuration (fstab: Entry not found) [ 16.614612] block: no usable configuration [ 16.619797] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 16.635997] urandom-seed: Seed file not found (/etc/urandom.seed) [ 16.912513] register mt7603_drv [ 16.915783] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=25 [ 16.921181] pci 0000:00:01.0: enabling device (0004 -> 0007) [ 16.926909] mt7603_drv 0000:02:00.0: enabling device (0000 -> 0002) [ 16.939516] [ 16.939516] [ 16.939516] === pAd = e5f6220d, size = 1648296 === [ 16.939516] [ 16.949201] <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x [ 16.955872] <-- RTMPAllocAdapterBlock, Status=0 [ 16.960384] pAd->CSRBaseAddress =0xc0900000, csr_addr=0xc0900000! [ 16.966478] device_id =0x7603 [ 16.969437] MT7603 AP Driver version 4.1.2.0 [ 16.973706] mt7603_init()--> [ 16.976577] mt_bcn_buf_init(224): Not support for HIF_MT yet! [ 16.982320] <--mt7603_init() [ 16.985189] load_dev_l1profile()--> [ 16.990600] match_index_by_chipname() MT7603 found as INDEX0 [ 16.996325] l1set_profile_path() profile update from /etc/Wireless/RT2860/RT2860AP.dat to /etc/wireless/mt7615/mt7615.1.dat [ 17.007455] l1set_eeprom_offset() eeprom offset remain 0x0 [ 17.012951] l1set_eeprom_size() eeprom size update from 0x200 to 0x400 [ 17.019461] l1set_ifname() ifname rename from ra0 to ra [ 17.024675] l1set_ifname() ifname remain ra [ 17.028852] l1set_ifname() ifname remain ra [ 17.033048] l1set_ifname() ifname remain apcli [ 17.115723] register rtpci [ 17.118563] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=24 [ 17.124015] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 17.129658] rtpci 0000:01:00.0: enabling device (0000 -> 0002) [ 17.140803] [ 17.140803] [ 17.140803] === pAd = ca6b6852, size = 1403632 === [ 17.140803] [ 17.150543] <-- RTMPAllocTxRxRingMemory, Status=0 [ 17.156067] <-- RTMPAllocAdapterBlock, Status=0 [ 17.160578] pAd->CSRBaseAddress =0xc0d00000, csr_addr=0xc0d00000! [ 17.166666] device_id =0x7662 [ 17.169629] ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a [ 17.179248] MT76x2 AP Driver version: 3.0.5.0 [ 17.183629] ====> mt76x2_ePA_per_rate_compensate_init: 5944 is_ePA: 1 [ 17.190039] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 [ 17.195419] RtmpEepromGetDefault::e2p_default=2 [ 17.199922] NVM is FLASH mode [ 17.202895] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=rai [ 17.210671] WiFi PCI Startup Time: 0.080s [ 17.243544] ralink_soc_eth 1e100000.ethernet: 0x100 = 0x6060000c, 0x10c = 0x80818 [ 17.330548] procd: - early - [ 17.333853] procd: - watchdog - [ 18.111702] procd: - watchdog - [ 18.116978] procd: - ubus - [ 18.296793] procd: - init - Please press Enter to activate this console. [ 18.991197] kmodloader: loading kernel modules from /etc/modules.d/ [ 19.017750] NET: Registered protocol family 38 [ 19.033858] tun: Universal TUN/TAP device driver, 1.6 [ 19.096623] cryptodev: driver 1.12 loaded. [ 19.119556] mtk-eip93 1e004000.crypto: EIP93 Crypto Engine Initialized. [ 19.155307] usbcore: registered new interface driver usblp [ 19.184398] xt_time: kernel timezone is -0000 [ 19.237560] PPP generic driver version 2.4.2 [ 19.243869] PPP MPPE Compression module registered [ 19.250167] NET: Registered protocol family 24 [ 19.279493] kmodloader: done loading kernel modules from /etc/modules.d/ [ 43.053920] ralink_soc_eth 1e100000.ethernet: PPE started [ 43.059447] debugfs: Directory 'mtk_ppe' with parent '/' already present! [ 43.073385] br-lan: port 1(eth0.1) entered blocking state [ 43.078811] br-lan: port 1(eth0.1) entered disabled state [ 43.084860] device eth0.1 entered promiscuous mode [ 43.089698] device eth0 entered promiscuous mode [ 43.100512] br-lan: port 1(eth0.1) entered blocking state [ 43.106063] br-lan: port 1(eth0.1) entered forwarding state [ 43.126866] load_dev_l1profile()--> [ 43.130600] l1set_profile_path() profile remain /etc/wireless/mt7615/mt7615.1.dat [ 43.138332] l1set_eeprom_offset() eeprom offset remain 0x0 [ 43.144250] l1set_eeprom_size() eeprom size remain 0x400 [ 43.149654] l1set_ifname() ifname rename from ra0 to ra [ 43.154969] l1set_ifname() ifname remain ra [ 43.159239] l1set_ifname() ifname remain ra [ 43.163608] l1set_ifname() ifname remain apcli [ 43.169198] TX_BCN DESC c0c9023d size = 320 [ 43.173725] RX[0] DESC dbcd3338 size = 2048 [ 43.178957] RX[1] DESC 91cfcb4f size = 2048 [ 43.370916] E2pAccessMode=2 [ 43.375217] cfg_mode=9 [ 43.377597] cfg_mode=9 [ 43.379975] wmode_band_equal(): Band Equal! [ 43.389479] APSDCapable[0]=1 [ 43.392465] APSDCapable[1]=1 [ 43.395367] APSDCapable[2]=1 [ 43.398249] APSDCapable[3]=1 [ 43.401128] APSDCapable[4]=1 [ 43.404053] APSDCapable[5]=1 [ 43.406952] APSDCapable[6]=1 [ 43.409840] APSDCapable[7]=1 [ 43.412771] APSDCapable[8]=1 [ 43.415664] APSDCapable[9]=1 [ 43.418542] APSDCapable[10]=1 [ 43.421614] APSDCapable[11]=1 [ 43.424595] APSDCapable[12]=1 [ 43.427567] APSDCapable[13]=1 [ 43.430539] APSDCapable[14]=1 [ 43.433564] APSDCapable[15]=1 [ 43.436545] default ApCliAPSDCapable[0]=1 [ 43.440552] default ApCliAPSDCapable[1]=1 [ 43.637251] Key1Str is Invalid key length(0) or Type(0) [ 43.642884] Key2Str is Invalid key length(0) or Type(0) [ 43.648478] Key3Str is Invalid key length(0) or Type(0) [ 43.654116] Key4Str is Invalid key length(0) or Type(0) [ 43.715757] [PMF]Set_PMFMFPC_Proc:: apidx=0, Desired MFPC=1 [ 43.721800] [PMF]Set_PMFMFPR_Proc:: apidx=0, Desired MFPR=0 [ 43.727725] [PMF]Set_PMFSHA256Proc:: apidx=0, Desired PMFSHA256=0 [ 43.735851] FW Version: [ 43.735868] C [ 43.738376] L [ 43.740090] 1 [ 43.741768] 7 [ 43.743462] 3 [ 43.745078] 7 [ 43.746690] 6 [ 43.748328] 6 [ 43.750074] [ 43.751785] R [ 43.753468] [ 43.756662] FW Build Date: [ 43.756676] 2 [ 43.759527] 0 [ 43.761164] 1 [ 43.762843] 7 [ 43.764463] 1 [ 43.766069] 1 [ 43.767668] 1 [ 43.769270] 0 [ 43.770871] 1 [ 43.772558] 0 [ 43.774193] 5 [ 43.775802] 9 [ 43.777401] 3 [ 43.779001] 2 [ 43.780605] [ 43.782287] [ 43.785882] CmdAddressLenReq:(ret = 0) [ 43.791146] CmdFwStartReq: override = 1, address = 1048576 [ 43.796990] CmdStartDLRsp: WiFI FW Download Success [ 43.816893] AsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) [ 43.822845] efuse_probe: efuse = 10000002 [ 43.827015] RtmpChipOpsEepromHook::e2p_type=2, inf_Type=5 [ 43.832573] RtmpEepromGetDefault::e2p_dafault=1 [ 43.837147] RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 1 [ 43.844775] NVM is FLASH mode, flash_offset = 0x0 [ 43.849634] 1. Phy Mode = 14 [ 43.854211] @@@ NICReadEEPROMParameters : pAd->FWLoad=0 [ 44.015132] Country Region from e2p = ffff [ 44.019279] tssi_1_target_pwr_g_band = 46 [ 44.023412] 2. Phy Mode = 14 [ 44.026461] 3. Phy Mode = 14 [ 44.029361] NICInitPwrPinCfg(14): Not support for HIF_MT yet! [ 44.035236] NICInitializeAsic(588): Not support rtmp_mac_sys_reset () for HIF_MT yet! [ 44.043094] mt_mac_init()--> [ 44.045978] mt7603_init_mac_cr()--> [ 44.049932] AsicSetMacMaxLen(1907): Set the Max RxPktLen=1024! [ 44.055848] <--mt_mac_init() [ 44.058930] WTBL Segment 1 info: [ 44.062290] MemBaseAddr/FID:0x28000/0 [ 44.066189] EntrySize/Cnt:32/128 [ 44.069603] WTBL Segment 2 info: [ 44.073002] MemBaseAddr/FID:0x40000/0 [ 44.076867] EntrySize/Cnt:64/128 [ 44.080270] WTBL Segment 3 info: [ 44.083640] MemBaseAddr/FID:0x42000/64 [ 44.087576] EntrySize/Cnt:64/128 [ 44.090977] WTBL Segment 4 info: [ 44.094363] MemBaseAddr/FID:0x44000/128 [ 44.098386] EntrySize/Cnt:32/128 [ 44.101887] AntCfgInit(2689): Not support for HIF_MT yet! [ 44.107563] MCS Set = ff ff 00 00 01 [ 46.002404] SYNC - BBP R4 to 20MHz.l [ 48.492538] SYNC - BBP R4 to 20MHz.l [ 50.992260] SYNC - BBP R4 to 20MHz.l [ 51.592359] SYNC - BBP R4 to 20MHz.l [ 52.192375] SYNC - BBP R4 to 20MHz.l [ 52.792370] SYNC - BBP R4 to 20MHz.l [ 53.392364] SYNC - BBP R4 to 20MHz.l [ 53.992466] SYNC - BBP R4 to 20MHz.l [ 54.592568] SYNC - BBP R4 to 20MHz.l [ 55.192410] SYNC - BBP R4 to 20MHz.l [ 55.792369] SYNC - BBP R4 to 20MHz.l [ 56.391470] [PMF]ap_pmf_init:: Security is not WPA2/WPA2PSK AES [ 56.397366] [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [ 56.403518] AsicSetRalinkBurstMode(4325): Not support for HIF_MT yet! [ 56.409926] RTMPSetPiggyBack(943): Not support for HIF_MT yet! [ 56.422023] AsicSetTxPreamble(4312): Not support for HIF_MT yet! [ 56.428048] The 4-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 4 [ 56.435717] AsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xa0 [ 56.441659] Main bssid = 20:76:93:48:a7:ba [ 56.445834] <==== rt28xx_init, Status=0 [ 56.453153] @@@ ed_monitor_exit : ===> [ 56.456935] @@@ ed_monitor_exit : <=== [ 56.460742] mt7603_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0x8564267c, EDCCA_Status=0 [ 56.468750] WiFi Startup Cost (ra0): 13.340s [ 56.474118] IPv6: ADDRCONF(NETDEVCHANGE): br-lan: link becomes ready [ 56.481152] br-lan: port 2(ra0) entered blocking state [ 56.486476] br-lan: port 2(ra0) entered disabled state [ 56.492363] device ra0 entered promiscuous mode [ 56.497316] br-lan: port 2(ra0) entered blocking state [ 56.502621] br-lan: port 2(ra0) entered forwarding state [ 56.511952] build time = [ 56.511963] 2 [ 56.514608] 0 [ 56.516302] 1 [ 56.517958] 4 [ 56.519567] 1 [ 56.521232] 1 [ 56.522992] 1 [ 56.524694] 5 [ 56.526371] 0 [ 56.528009] 6 [ 56.529620] 0 [ 56.531240] 6 [ 56.532906] 0 [ 56.534509] 6 [ 56.536194] a [ 56.537829] [ 56.541032] [ 56.542694] rom patch for E3 IC [ 56.545883] [ 56.547666] platform = [ 56.547678] A [ 56.550159] L [ 56.551827] P [ 56.553437] S [ 56.555034] [ 56.558213] hw/sw version = [ 56.558230] 8a [ 56.561145] 10 [ 56.562955] 8a [ 56.564663] 10 [ 56.566369] [ 56.569562] patch version = [ 56.569571] 0 [ 56.572517] 0 [ 56.574092] 0 [ 56.575662] 10 [ 56.577230] [ 56.593535] FW Version:0.0.00 [ 56.593546] Build:1 [ 56.599051] Build Time: [ 56.599057] 2 [ 56.601645] 0 [ 56.603355] 1 [ 56.604969] 6 [ 56.606557] 0 [ 56.608140] 7 [ 56.609731] 1 [ 56.611322] 1 [ 56.612999] 1 [ 56.614587] 4 [ 56.616182] 4 [ 56.617766] 3 [ 56.619365] [ 56.620944] [ 56.622566] [ 56.624144] _ [ 56.625718] [ 56.628766] fw for E3 IC [ 56.649096] RX[0] DESC 57d47084 size = 4096 [ 56.655132] RX[1] DESC dcd69e09 size = 512 [ 56.662281] E2pAccessMode=2 [ 56.665860] cfg_mode=14 [ 56.668331] cfg_mode=14 [ 56.670823] wmode_band_equal(): Band Not Equal! [ 56.815783] Key1Str is Invalid key length(0) or Type(0) [ 56.821304] Key2Str is Invalid key length(0) or Type(0) [ 56.826821] Key3Str is Invalid key length(0) or Type(0) [ 56.832331] Key4Str is Invalid key length(0) or Type(0) [ 56.855221] 1. Phy Mode = 49 [ 56.858436] Initialize MAC Address from E2PROM [ 56.863157] E2PROM MAC: 20:76:93:48:a7:bc [ 56.867160] Use the MAC address what is assigned from EEPROM. [ 56.873013] Current MAC: 20:76:93:48:a7:bc [ 56.877220] get_chl_grp:illegal channel (167) [ 56.881634] get_chl_grp:illegal channel (167) [ 56.886028] get_chl_grp:illegal channel (169) [ 56.890395] get_chl_grp:illegal channel (169) [ 56.894762] get_chl_grp:illegal channel (171) [ 56.899119] get_chl_grp:illegal channel (171) [ 56.903502] get_chl_grp:illegal channel (173) [ 56.907888] get_chl_grp:illegal channel (173) [ 56.912289] Country Region from e2p = ffff [ 56.916381] mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 [ 56.924299] mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=1 [ 56.931278] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9 [ 56.940072] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 [ 56.948765] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4 [ 56.957541] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 [ 56.966227] mt76x2_get_external_lna_gain::LNA type=0x1, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8f, ALNAGain1=0xffffff8f, ALNAGain2=0xffffff8f [ 56.978898] 2. Phy Mode = 49 [ 56.981852] 3. Phy Mode = 49 [ 56.984770] andes_pci_fw_init [ 56.987877] 0x1300 = 00073200 [ 57.022398] AntCfgInit: primary/secondary ant 0/1 [ 57.027145] andes_load_cr:cr_type(2) [ 57.043567] MCS Set = ff ff 00 00 01 [ 61.061439] ch40 bssid=dc:d8:7c:45:56:ff [ 61.065450] ch161 bssid=52:33:f0:3d:bd:06 [ 61.069521] ===================================================== [ 61.075612] Channel 36 : Dirty = 32, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.083596] Channel 40 : Dirty = 90, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.091581] Channel 44 : Dirty = 32, False CCA = 3, Busy Time = 0, Skip Channel = FALSE [ 61.099725] Channel 48 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.107769] Channel 149 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.115789] Channel 153 : Dirty = 0, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.123769] Channel 157 : Dirty = 32, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.131840] Channel 161 : Dirty = 80, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.139889] Channel 165 : Dirty = 32, False CCA = 0, Busy Time = 0, Skip Channel = FALSE [ 61.147953] ===================================================== [ 61.154176] Rule 1 CCA value : Min Dirtiness (Include extension channel) ==> Select Channel 149 [ 61.162939] Min Dirty = 112 [ 61.165714] ExChannel = 0 , 0 [ 61.168662] BW = 80 [ 61.171666] mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=149, HT-CentCh=151, VHT-CentCh=155 [ 61.226884] APStartUp(): AP Set CentralFreq at 155(Prim=149, HT-CentCh=151, VHT-CentCh=155, BBP_BW=2) [ 61.246205] mt76x2_calibration(channel = 155) [ 61.618750] Main bssid = 20:76:93:48:a7:bc [ 61.622864] mt76x2_reinit_agc_gain:original agc_vga0 = 0x42, agc_vga1 = 0x42 [ 61.629877] mt76x2_reinit_agc_gain:updated agc_vga0 = 0x42, agc_vga1 = 0x42 [ 61.636829] mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x36, hi_lna1 = 0x36 [ 61.643944] mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x36, hi_lna1 = 0x36 [ 61.650956] original vga value(chain0) = 42 [ 61.655136] original vga value(chain1) = 42 [ 61.659308] <==== rt28xx_init, Status=0 [ 61.663153] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wdsi [ 61.671087] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wdsi [ 61.679105] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wdsi [ 61.687025] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=wdsi [ 61.694913] get_dev_name_prefix(): dev_idx = 0, dev_name_prefix=apclii [ 61.702938] RTMPDrvOpen(1):Check if PDMA is idle! [ 61.707681] RTMPDrvOpen(2):Check if PDMA is idle! [ 61.712520] WiFi Interface Up Time (rai0): 5.200s [ 61.720245] br-lan: port 3(rai0) entered blocking state [ 61.725606] br-lan: port 3(rai0) entered disabled state [ 61.731536] device rai0 entered promiscuous mode [ 61.736594] br-lan: port 3(rai0) entered blocking state [ 61.741869] br-lan: port 3(rai0) entered forwarding state [ 68.001220] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 68.008185] jffs2_build_filesystem(): unlocking the mtd device... [ 68.008223] done. [ 68.016471] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 68.835658] done. [ 68.845079] jffs2: notice: (3809) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 69.487629] overlayfs: upper fs does not support tmpfile. [ 69.883601] jffs2: warning: (3812) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=28 [ 69.892401] jffs2: warning: (3812) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 69.900952] jffs2: warning: (3812) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 78.707550] jffs2: warning: (4400) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 78.716140] jffs2: warning: (4400) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 78.724767] jffs2: warning: (4400) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 78.795211] jffs2: warning: (4400) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 78.803724] jffs2: warning: (4400) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 78.812227] jffs2: warning: (4400) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 81.845153] jffs2: warning: (4494) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 81.853630] jffs2: warning: (4494) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 81.862091] jffs2: warning: (4494) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 81.929456] jffs2: warning: (4494) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 81.937920] jffs2: warning: (4494) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 81.946396] jffs2: warning: (4494) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 82.676662] jffs2: warning: (4495) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 82.685150] jffs2: warning: (4495) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 82.693619] jffs2: warning: (4495) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 82.760500] jffs2: warning: (4495) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 82.769010] jffs2: warning: (4495) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 82.777545] jffs2: warning: (4495) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 83.350283] jffs2: warning: (4496) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 83.358797] jffs2: warning: (4496) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 83.367271] jffs2: warning: (4496) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 83.434248] jffs2: warning: (4496) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 83.442723] jffs2: warning: (4496) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76 [ 83.451167] jffs2: warning: (4496) do_jffs2_setxattr: jffs2_reserve_space()=-28, request=76

coolsnowwolf / lede