Library's Non-declared variables & too many arguments to function issues.

[QnBarb]

Version/revision of the library used

2.8.6

Describe the bug

Variables not declared: timerAlarmEnable; timerAlarmWrite; timerAlarmDisable(timer); gpio_intr_disable((gpio_num_t)params.recvpin); gpio_intr_enable((gpio_num_t)params.recvpin)

Too many arguments to function: timer = timerBegin(_timer_num, 80, true); timerAttachInterrupt(timer, &read_timeout, false)

To Reproduce

Compile/Upload

Example code used

include

include

include

include

// an IR detector/demodulator is connected to GPIO pin 2 uint16_t RECV_PIN = 2;

IRrecv irrecv(RECV_PIN);

decode_results results;

void setup() { Serial.begin(115200); irrecv.enableIRIn(); // Start the receiver }

void dump(decode_results *results) { // Dumps out the decode_results structure. // Call this after IRrecv::decode() uint16_t count = results->rawlen; if (results->decode_type == UNKNOWN) { Serial.print("Unknown encoding: "); } else if (results->decode_type == NEC) { Serial.print("Decoded NEC: "); } else if (results->decode_type == SONY) { Serial.print("Decoded SONY: "); } else if (results->decode_type == RC5) { Serial.print("Decoded RC5: "); } else if (results->decode_type == RC5X) { Serial.print("Decoded RC5X: "); } else if (results->decode_type == RC6) { Serial.print("Decoded RC6: "); } else if (results->decode_type == RCMM) { Serial.print("Decoded RCMM: "); } else if (results->decode_type == PANASONIC) { Serial.print("Decoded PANASONIC - Address: "); Serial.print(results->address, HEX); Serial.print(" Value: "); } else if (results->decode_type == LG) { Serial.print("Decoded LG: "); } else if (results->decode_type == JVC) { Serial.print("Decoded JVC: "); } else if (results->decode_type == AIWA_RC_T501) { Serial.print("Decoded AIWA RC T501: "); } else if (results->decode_type == WHYNTER) { Serial.print("Decoded Whynter: "); } else if (results->decode_type == NIKAI) { Serial.print("Decoded Nikai: "); } serialPrintUint64(results->value, 16); Serial.print(" ("); Serial.print(results->bits, DEC); Serial.println(" bits)"); Serial.print("Raw ("); Serial.print(count, DEC); Serial.print("): {");

for (uint16_t i = 1; i < count; i++) { if (i % 100 == 0) yield(); // Preemptive yield every 100th entry to feed the WDT. if (i & 1) { Serial.print(results->rawbuf[i] kRawTick, DEC); } else { Serial.print(", "); Serial.print((uint32_t) results->rawbuf[i] kRawTick, DEC); } } Serial.println("};"); }

void loop() { if (irrecv.decode(&results)) { dump(&results); Serial.println("DEPRECATED: Please use IRrecvDumpV2.ino instead!"); irrecv.resume(); // Receive the next value } }

Expected behaviour

1. Compile.
2. Expect compile.

Output of raw data from [IRrecvDumpV2.ino]

c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp: In function 'void gpio_intr()': c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:246:3: error: 'timerAlarmEnable' was not declared in this scope; did you mean 'timerAlarm'? 246 | timerAlarmEnable(timer); | ^~~~ | timerAlarm c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp: In member function 'void IRrecv::enableIRIn(bool)': c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:362:21: error: too many arguments to function 'hw_timer_t timerBegin(uint32_t)' 362 | timer = timerBegin(_timer_num, 80, true); | ~~^~~~~~ In file included from C:\Users\QuangPC\AppData\Local\Arduino15\packages\esp32\hardware\esp32\3.0.0-alpha3\cores\esp32/esp32-hal.h:84, from C:\Users\QuangPC\AppData\Local\Arduino15\packages\esp32\hardware\esp32\3.0.0-alpha3\cores\esp32/Arduino.h:36, from c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.h:10, from c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:6: C:\Users\QuangPC\AppData\Local\Arduino15\packages\esp32\hardware\esp32\3.0.0-alpha3\cores\esp32/esp32-hal-timer.h:35:14: note: declared here 35 | hw_timer_t timerBegin(uint32_t frequency); | ^~~~~~ c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:371:3: error: 'timerAlarmWrite' was not declared in this scope; did you mean 'timerWrite'? 371 | timerAlarmWrite(timer, MS_TO_USEC(params.timeout), ONCE); | ^~~~~~~ | timerWrite c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:375:23: error: too many arguments to function 'void timerAttachInterrupt(hw_timer_t, void ()())' 375 | timerAttachInterrupt(timer, &read_timeout, false); | ~~~~^~~~~~~~~ C:\Users\QuangPC\AppData\Local\Arduino15\packages\esp32\hardware\esp32\3.0.0-alpha3\cores\esp32/esp32-hal-timer.h:50:6: note: declared here 50 | void timerAttachInterrupt(hw_timer_t timer, void (userFunc)(void)); | ^~~~~~~~ c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp: In member function 'void IRrecv::disableIRIn()': c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:401:3: error: 'timerAlarmDisable' was not declared in this scope 401 | timerAlarmDisable(timer); | ^~~~~ c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp: In member function 'void IRrecv::pause()': c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:416:3: error: 'gpio_intr_disable' was not declared in this scope; did you mean 'esp_intr_disable'? 416 | gpio_intr_disable((gpio_num_t)params.recvpin); | ^~~~~ | esp_intr_disable c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp: In member function 'void IRrecv::resume()': c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:429:3: error: 'timerAlarmDisable' was not declared in this scope 429 | timerAlarmDisable(timer); | ^~~~~ c:\Users\QuangPC\Documents\Arduino\libraries\IRremoteESP8266\src\IRrecv.cpp:430:3: error: 'gpio_intr_enable' was not declared in this scope; did you mean 'esp_intr_enable'? 430 | gpio_intr_enable((gpio_num_t)params.recvpin); | ^~~~ | esp_intr_enable

exit status 1

Compilation error: exit status 1

What brand/model IR demodulator are you using?

Vishay TSSP93056.

Circuit diagram and hardware used (if applicable)

Board used: ESP32C3DevKitM-1

I have followed the steps in the Troubleshooting Guide & read the FAQ

_Yes

Has this library/code previously worked as expected for you?

_No

Other useful information

-

[NiKiZe]

This seems to be related to C3 and features in the Arduino framework that has changed, see already existing issues.