search

cubieplayer / Cubian

Debian for Cubieboard
http://cubian.org
271 stars 49 forks source link

Booting failure with Cubian-desktop-x1-a20-cubietruck-vga.img image #368

Open yshsu168 opened 9 years ago

yshsu168 commented 9 years ago

Here comes the UART console log.

U-Boot SPL 2014.01-rc1-09161-g108ec3f (Jan 20 2014 - 05:50:52) Board: Cubietruck DRAM: 2048 MiB CPU: 960000000Hz, AXI/AHB/APB: 3/2/2 spl: not an uImage at 1600

U-Boot 2014.01-rc1-09161-g108ec3f (Jan 20 2014 - 05:50:52) Allwinner Technology

CPU: Allwinner A20 (SUN7I) Board: Cubietruck I2C: ready DRAM: 2 GiB WARNING: Caches not enabled MMC: SUNXI SD/MMC: 0 *\ Warning - bad CRC, using default environment

In: serial Out: serial Err: serial Net: mii0 Warning: failed to set MAC address

Hit any key to stop autoboot: 1  0 \ Unrecognized filesystem type \ File not found boot/uEnv.txt 150 bytes read in 13 ms (10.7 KiB/s) Loaded environment from uEnv.txt \ Unrecognized filesystem type \ File not found boot/boot.scr \ File not found boot.scr \ File not found /boot/script.bin \ Unrecognized filesystem type ** 50028 bytes read in 15 ms (3.2 MiB/s) 5912576 bytes read in 430 ms (13.1 MiB/s)

Booting kernel from Legacy Image at 48000000 ...

Image Name: Linux-3.4.79-sun7i Created: 2014-07-02 22:40:15 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5912512 Bytes = 5.6 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK

Starting kernel ...

<6>Booting Linux on physical CPU 0 <6>Initializing cgroup subsys cpuset <6>Initializing cgroup subsys cpu <5>Linux version 3.4.79-sun7i (root@ubtu) (gcc version 4.8.2 20130603 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2013.06 - Linaro GCC 2013.06) ) #14 SMP PREEMPT Thu Jul 3 06:39:51 CST 2014 CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: sun7i <6>Memory Reserved: <6> SYS : 0x43000000 - 0x4300ffff ( 64 kB) <6> G2D : 0x50000000 - 0x50ffffff ( 16 MB) <6> LCD : 0x51000000 - 0x52ffffff ( 32 MB) <7>cma: dma_contiguous_reserve(limit 4fffffff) <7>cma: dma_contiguous_reserve: reserving 192 MiB for global area <7>cma: dma_declare_contiguous(size c000000, base 00000000, limit 4fffffff) <6>cma: CMA: reserved 192 MiB at 43c00000 Memory policy: ECC disabled, Data cache writealloc <6>sunxi: Allwinner A20 (AW1651/sun7i) detected. <7>On node 0 totalpages: 524288 <7>free_area_init_node: node 0, pgdat c0b30500, node_mem_map d3000000 <7> DMA zone: 512 pages used for memmap <7> DMA zone: 0 pages reserved <7> DMA zone: 65024 pages, LIFO batch:15 <7> Normal zone: 1008 pages used for memmap <7> Normal zone: 128016 pages, LIFO batch:31 <7> HighMem zone: 2576 pages used for memmap <7> HighMem zone: 327152 pages, LIFO batch:31 <6>PERCPU: Embedded 7 pages/cpu @d400e000 s7616 r8192 d12864 u32768 <7>pcpu-alloc: s7616 r8192 d12864 u32768 alloc=8*4096 <7>pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520192 <5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 console=tty2 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:0 consoleblank=0 loglevel=0 <6>PID hash table entries: 4096 (order: 2, 16384 bytes) <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>allocated 4194304 bytes of page_cgroup <6>please try 'cgroup_disable=memory' option if you don't want memory cgroups <6>Memory: 2048MB = 2048MB total <5>Memory: 1816100k/1816100k available, 281052k reserved, 1318912K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) lowmem : 0xc0000000 - 0xef800000 ( 760 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0a7b204 (10701 kB) .init : 0xc0a7c000 - 0xc0ab8dc0 ( 244 kB) .data : 0xc0aba000 - 0xc0b39398 ( 509 kB) .bss : 0xc0b393bc - 0xc0d21cd8 (1955 kB) <6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>Preemptible hierarchical RCU implementation. <6> RCU dyntick-idle grace-period acceleration is enabled. <6>NR_IRQS:192 <6>Architected local timer running at 24.00MHz. <6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms <2>start_kernel(): bug: interrupts were enabled early <6>Console: colour dummy device 80x30 <6>console [tty2] enabled <6>Calibrating delay loop... 1908.73 BogoMIPS (lpj=9543680) <6>pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 512 <6>Initializing cgroup subsys cpuacct <6>Initializing cgroup subsys memory <6>Initializing cgroup subsys devices <6>Initializing cgroup subsys freezer <6>Initializing cgroup subsys blkio <6>Initializing cgroup subsys perf_event <6>CPU: Testing write buffer coherency: ok <6>CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available <6>Setting up static identity map for 0x40788798 - 0x407887f0 CPU1: Booted secondary processor <6>CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>Brought up 2 CPUs <6>SMP: Total of 2 processors activated (3824.02 BogoMIPS). <6>devtmpfs: initialized <6>xor: measuring software checksum speed <6> arm4regs : 1332.000 MB/sec <6> 8regs : 705.600 MB/sec <6> 32regs : 798.000 MB/sec <6>xor: using function: arm4regs (1332.000 MB/sec) <6>dummy: <7>cma: cma_init_reserved_areas() <7>cma: cma_create_area(base 00043c00, count c000) <7>cma: cma_create_area: returned ef0ab1c0 <6>NET: Registered protocol family 16 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 64, align 6) <7>cma: dma_alloc_from_contiguous(): returned d3078000 <6>DMA: preallocated 256 KiB pool for atomic coherent allocations <6>hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ccu-inf] aw clock manager init <6>[ccu-inf] aw_ccu_init <6>[ccu-inf] script config pll3 to 297MHz <6>[ccu-inf] script config pll4 to 300MHz <6>[ccu-inf] script config pll6 to 600MHz <6>[ccu-inf] script config pll7 to 297MHz <6>[ccu-inf] script config pll8 to 336MHz <6>Init eGon pin module V2.0 <6>bio: create slab at 0 raid6: int32x1 151 MB/s raid6: int32x2 189 MB/s raid6: int32x4 209 MB/s raid6: int32x8 196 MB/s raid6: using algorithm int32x4 (209 MB/s) <5>SCSI subsystem initialized <7>libata version 3.00 loaded. <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>Linux media interface: v0.10 <6>Linux video capture interface: v2.00 <6>Advanced Linux Sound Architecture Driver Version 1.0.25. <6>cfg80211: Calling CRDA to update world regulatory domain <6>Switching to clocksource arch_sys_counter <5>FS-Cache: Loaded <6>CacheFiles: Loaded WRN:L287(drivers/usb/sunxi_usb/manager/usb_manager.c):ERR: det_vbus pin is invaild WRN:L426(drivers/usb/sunxi_usb/manager/usb_manager.c):ERR: check_usb_board_info failed WRN:L480(drivers/usb/sunxi_usb/manager/usb_manager.c):ERR: get_usb_cfg failed <6>NET: Registered protocol family 2 <6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes) <6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes) <6>TCP bind hash table entries: 65536 (order: 7, 786432 bytes) <6>TCP: Hash tables configured (established 131072 bind 65536) <6>TCP: reno registered <6>UDP hash table entries: 512 (order: 2, 16384 bytes) <6>UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>NET: Registered protocol family 1 <6>RPC: Registered named UNIX socket transport module. <6>RPC: Registered udp transport module. <6>RPC: Registered tcp transport module. <6>RPC: Registered tcp NFSv4.1 backchannel transport module. pm: select wifi: ap6210 <6>ap6xxx: config 32k clock [wifi_pm]: wifi gpio init is OK !! [rfkill]: rfkill set power 0 <6>audit: initializing netlink socket (disabled) <5>type=2000 audit(1.410:1): initialized highmem bounce pool size: 64 pages <5>VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <5>NFS: Registering the id_resolver key type <6>nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>NTFS driver 2.1.30 [Flags: R/W]. <6>fuse init (API version 7.18) <6>OCFS2 1.5.0 <6>ocfs2: Registered cluster interface o2cb <6>OCFS2 DLMFS 1.5.0 OCFS2 User DLM kernel interface loaded <6>OCFS2 Node Manager 1.5.0 <6>OCFS2 DLM 1.5.0 <6>Btrfs loaded <6>msgmni has been set to 1355 <3>alg: comp: Compression test 1 failed for lzo-generic: output len = 57 <6>alg: No test for stdrng (krng) <6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) <6>io scheduler noop registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <6>sunxi disp driver loaded (/dev/disp api 1.0) <6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled <6>[uart]: used uart info.: 0x05 <6>[uart]: serial probe 0 irq 33 mapbase 0x01c28000 <6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A <6>console [ttyS0] enabled <6>[uart]: serial probe 2 irq 35 mapbase 0x01c28800 <6>sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A <7>G2D: drv_g2d_init <6>G2D: g2dmem: g2d_start=50000000, g2d_size=1000000 <6>G2D: head:d0000000,tail:d1000000 <6>G2D: Module initialized.major:250 <6>brd: module loaded <6>loop: module loaded [NAND] nand driver version: 0x2 0x9 <4>Dev Sunxi softw311 nand magic does not match for MBR 1: softw411 <4>Dev Sunxi softw311 nand magic does not match for MBR 2: <4>Dev Sunxi softw311 nand magic does not match for MBR 3: <4>Dev Sunxi softw311 nand magic does not match for MBR 4: <4>Dev Sunxi softw311 nand header bad for all MBR copies, MBR corrupted or not present. <4>Dev Sunxi softw411 nand: part 1, start 128, size 2048 <4>Dev Sunxi softw411 nand: part 2, start 2176, size 15038336 <6> nand: nanda nandb [NAND]nand driver, ok. <6>sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP <4>sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1 <6>sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 23, align 5) <7>cma: dma_alloc_from_contiguous(): returned d3078800 <6>scsi0 : sw_ahci_platform <6>ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 <3>[spi-err] Get spi devices number failed <3>[spi-err] register spi devices board info failed <4>spi: cannot find any using configuration for all 4 spi controllers, return directly! <4>emac_init fetch emac using configuration failed <6>emac driver is disabled <6>gmac: use mac address from chipid <6>eth%d: device MAC address 02:0c:0a:41:75:44 [gmac]: sun6i_gmac platform driver registration completed <6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [sw-ehci1]: open clock [sw-ehci1]: Set USB Power ON <6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 1 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078ae0 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b00 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b20 <6>sw-ehci sw-ehci.1: irq 71, io mem 0x01c14000 <6>sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00 <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 1 port detected [sw-ohci1]: open clock <6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 2 <6>sw-ohci sw-ohci.1: irq 96, io mem 0x01c14400 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b40 ehci_irq: port change detect <6>hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 1 port detected [sw-ehci2]: open clock [sw-ehci2]: Set USB Power ON <6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 3 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b60 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b80 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078ba0 <6>sw-ehci sw-ehci.2: irq 72, io mem 0x01c1c000 <6>ata1: SATA link down (SStatus 0 SControl 300) <6>sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00 ehci_irq: port change detect ehci_irq: port change detect <6>hub 3-0:1.0: USB hub found <6>hub 3-0:1.0: 1 port detected [sw-ohci2]: open clock <6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 4 <6>sw-ohci sw-ohci.2: irq 97, io mem 0x01c1c400 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) The port change to OHCI now! <7>cma: dma_alloc_from_contiguous(): returned d3078bc0 <6>hub 4-0:1.0: USB hub found <6>hub 4-0:1.0: 1 port detected <6>Initializing USB Mass Storage driver... <6>usbcore: registered new interface driver usb-storage <6>USB Mass Storage support registered. <6>usbcore: registered new interface driver ums-alauda <6>usbcore: registered new interface driver ums-cypress <6>usbcore: registered new interface driver ums-datafab <6>usbcore: registered new interface driver ums_eneub6250 <6>usbcore: registered new interface driver ums-freecom <6>usbcore: registered new interface driver ums-isd200 <6>usbcore: registered new interface driver ums-jumpshot <6>usbcore: registered new interface driver ums-karma <6>usbcore: registered new interface driver ums-onetouch <6>usbcore: registered new interface driver ums-realtek <6>usbcore: registered new interface driver ums-sddr09 <6>usbcore: registered new interface driver ums-sddr55 <6>usbcore: registered new interface driver ums-usbat <6>usbcore: registered new interface driver usbserial <6>usbcore: registered new interface driver usbserial_generic <6>USB Serial support registered for generic <6>usb 2-1: new low-speed USB device number 2 using sw-ohci ehci_irq: port change detect The port change to OHCI now! <6>usbserial: USB Serial Driver core <6>mousedev: PS/2 mouse device common for all mice <6>sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 <6>i2c /dev entries driver config i2c gpio with gpio_config api <6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected <6>axp_mfd 0-0034: AXP internal temperature monitoring enabled [AXP]axp driver uning configuration failed(342) [AXP]power_start = 0 <6>I2C: i2c-0: AW16XX I2C adapter <6>lirc_dev: IR Remote Control driver registered, major 249 <6>IR NEC protocol handler initialized <6>IR RC5(x) protocol handler initialized <6>IR RC6 protocol handler initialized <6>IR JVC protocol handler initialized <6>IR Sony protocol handler initialized <6>IR RC5 (streamzap) protocol handler initialized <6>IR SANYO protocol handler initialized <6>IR MCE Keyboard/mouse protocol handler initialized <6>IR LIRC bridge handler initialized [ace_drv] start!!! [ace_drv] init end!!! [pa_drv] start!!! [pa_drv] init end!!! <6>axp20_ldo1: 1300 mV <6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV <6>axp20_ldo3: 700 <--> 3500 mV at 2800 mV <6>axp20_ldo4: 1250 <--> 3300 mV at 2800 mV <6>axp20_buck2: 700 <--> 2275 mV at 1450 mV <6>axp20_buck3: 700 <--> 3500 mV at 1300 mV <6>axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV <6>input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0 <4>axp20_ldo2: Failed to create debugfs directory <6>md: linear personality registered for level -1 <6>md: raid0 personality registered for level 0 <6>md: raid1 personality registered for level 1 <6>md: raid10 personality registered for level 10 <6>md: raid6 personality registered for level 6 <6>md: raid5 personality registered for level 5 <6>md: raid4 personality registered for level 4 <6>md: multipath personality registered for level -4 <6>md: faulty personality registered for level -5 <6>device-mapper: uevent: version 1.0.3 <6>device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com <6>device-mapper: multipath: version 1.3.0 loaded <6>device-mapper: multipath round-robin: version 1.0.0 loaded <6>device-mapper: multipath queue-length: version 0.1.0 loaded <6>device-mapper: multipath service-time: version 0.2.0 loaded <6>device-mapper: dm-log-userspace: version 1.1.0 loaded <6>cpuidle: using governor ladder <6>cpuidle: using governor menu <6>usbcore: registered new interface driver ushc <6>[mmc-msg] sw_mci_init <6>[mmc-msg] get mmc2's IO(det) failed <6>[mmc-msg] Not using mmc2 due to script.bin parse failure <6>[mmc-msg] MMC host used card: 0xb, boot card: 0x0, io_card 8 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078be0 <6>[mmc-msg] sdc0 set round clock 400000, src 24000000 <6>[mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 Probe: base:0xf00de000 irq:64 sg_cpu:c3c5f000(43c5f000) ret 0. <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c00 <6>[mmc-msg] sdc1 set round clock 400000, src 24000000 <6>usb 4-1: new low-speed USB device number 2 using sw-ohci <6>[mmc-msg] sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] mmc 0 detect change, present 1 <3>[mmc-err] update clock timeout, fatal error <6>[mmc-msg] sdc1 Probe: base:0xf00e0000 irq:65 sg_cpu:c3c60000(43c60000) ret 0. <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c20 <6>[mmc-msg] sdc3 set round clock 400000, src 24000000 <6>[mmc-msg] sdc3 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 Probe: base:0xf00e2000 irq:67 sg_cpu:c3c61000(43c61000) ret 0. [mmc_pm]: failed to fetch sdio card configuration! <6>sunxi_leds driver init <7>Registered led device: green:ph20:led1 <7>Registered led device: blue:ph21:led2 <6>ledtrig-cpu: registered to indicate activity on CPUs <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c40 <6>input: USB OPTICAL MOUSE as /devices/platform/sw-ohci.1/usb2/2-1/2-1:1.0/input/input1 <6>generic-usb 0003:15D9:0A4D.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-sw-ohci-1/input0 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c60 <6>input: Dell Dell USB Keyboard as /devices/platform/sw-ohci.2/usb4/4-1/4-1:1.0/input/input2 <6>generic-usb 0003:413C:2003.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-sw-ohci-1/input0 <6>usbcore: registered new interface driver usbhid <6>usbhid: USB HID core driver <6>logger: created 256K log 'log_main' <6>logger: created 256K log 'log_events' <6>logger: created 256K log 'log_radio' <6>logger: created 256K log 'log_system' <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 8, align 3) <7>cma: dma_alloc_from_contiguous(): returned d3078d00 <6>IPv4 over IPv4 tunneling driver <6>TCP: bic registered <6>TCP: cubic registered <6>TCP: westwood registered <6>TCP: highspeed registered <6>TCP: hybla registered <6>TCP: htcp registered <6>TCP: vegas registered <6>TCP: veno registered <6>TCP: scalable registered <6>TCP: lp registered <6>TCP: yeah registered <6>TCP: illinois registered <6>Initializing XFRM netlink socket <6>NET: Registered protocol family 10 <6>NET: Registered protocol family 17 <6>NET: Registered protocol family 15 [mmc_pm]: No sdio card, please check your config !! <5>Registering the dns_resolver key type <6>VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4 <5>Registering SWP/SWPB emulation handler <4>axp20_buck2: Failed to create debugfs directory <6>[cpu_freq] INF:-------------------V-F Table------------------- <6>[cpu_freq] INF: voltage = 1500mv frequency = 1056MHz <6>[cpu_freq] INF: voltage = 1450mv frequency = 1008MHz <6>[cpu_freq] INF: voltage = 1350mv frequency = 912MHz <6>[cpu_freq] INF: voltage = 1300mv frequency = 864MHz <6>[cpu_freq] INF: voltage = 1100mv frequency = 528MHz <6>[cpu_freq] INF: voltage = 1050mv frequency = 312MHz <6>[cpu_freq] INF: voltage = 1050mv frequency = 144MHz <6>[cpu_freq] INF: voltage = 1000mv frequency = 0MHz <6>[cpu_freq] INF:----------------------------------------------- <3>[cpu_freq] ERR:cpu max or min frequency from sysconfig is more than range <3>[cpu_freq] ERR:sunxi_cpufreq_initcall, use default cpu max/min frequency, max freq: 1008MHz, min freq: 60MHz <6>registered taskstats version 1 <4>[DISP] Invalid mode string: EDID:0, ignoring <6>[mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 power on <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set round clock 400000, src 24000000 <3>[mmc-err] smc 0 err, cmd 52, RTO <3>[mmc-err] smc 0 err, cmd 52, RTO <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <3>[mmc-err] smc 0 err, cmd 5, RTO <3>[mmc-err] smc 0 err, cmd 5, RTO <3>[mmc-err] smc 0 err, cmd 5, RTO <3>[mmc-err] smc 0 err, cmd 5, RTO <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc0 set round clock 42857143, src 600000000 <6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B <6>mmc0: new high speed SDHC card at address 0002 <6>mmcblk0: mmc0:0002 7.52 GiB <6> mmcblk0: p1 p2 <6>Console: switching to colour frame buffer device 128x48 <6>I2C: i2c-1: HDMI I2C adapter <4>axp20_buck3: incomplete constraints, leaving on <4>axp20_buck2: incomplete constraints, leaving on <4>axp20_ldo4: incomplete constraints, leaving on <4>axp20_ldo3: incomplete constraints, leaving on <4>axp20_ldo2: incomplete constraints, leaving on <4>axp20_ldo1: incomplete constraints, leaving on <6>sunxi-rtc sunxi-rtc: setting system clock to 2014-10-09 04:40:03 UTC (1412829603) <6>ALSA device list: <6> #0: sunxi-CODEC Audio Codec <6>md: Waiting for all devices to be available before autodetect <6>md: If you don't use raid, use raid=noautodetect <6>md: Autodetecting RAID arrays. <6>md: Scanned 0 and added 0 devices. <6>md: autorun ... <6>md: ... autorun DONE. <3>EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240) <3>EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (244) <6>EXT4-fs (mmcblk0p2): recovery complete <6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) <6>VFS: Mounted root (ext4 filesystem) on device 179:2. <6>devtmpfs: mounted <6>Freeing init memory: 240K <30>udevd[177]: starting version 175 <6>EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) <6>EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) <6>sunxi_gpio driver init ver 1.3 <6>gpiochip_add: registered GPIOs 1 to 67 on device: A1X_GPIO UMP<2>: Inserting UMP device driver. Compiled: May 25 2014, time: 09:11:38 UMP<2>: Using OS memory backend, allocation limit: 134217728 UMP: UMP device driver loaded Mali: permit MALI_IOC_MEM_MAP_EXT ioctl for framebuffer (paddr=0x51000000, size=33554432) <6>mali: use config clk_div 1 <6>mali: clk_div 1 Mali: mali clock set completed, clock is 312000000 Hz <6>mali: use config clk_div 1 <6>mali: clk_div 1 Mali: mali clock set completed, clock is 312000000 Hz <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 64, align 6) <7>cma: dma_alloc_from_contiguous(): returned d3079000 Mali: Mali device driver loaded <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 20480, align 8) <7>cma: dma_alloc_from_contiguous(): returned d307a000 [cedar dev]: install start!!! [cedar dev]: install end!!! <6>bcmdhd: got gpio2, mapped to irqno170 dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to turn on WL_REG_ON <6>sdio wifi power state: on <6>[mmc-msg] sdc3 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 power on <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 set round clock 400000, src 24000000 <3>[mmc-err] smc 3 err, cmd 52, RTO <3>[mmc-err] smc 3 err, cmd 52, RTO <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <3>[mmc-err] smc 3 err, cmd 8, RTO <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <4>mmc2: queuing unknown CIS tuple 0x80 (2 bytes) <4>mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>mmc2: queuing unknown CIS tuple 0x80 (7 bytes) <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc3 set round clock 42857143, src 600000000 =========== WLAN placed in POWER ON ======== <6>[mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B <6>mmc2: new high speed SDIO card at address 0001 Linux Kernel SDIO/MMC Driver Dongle Host Driver, version 1.28.23.3 (r) Compiled in drivers/net/wireless/bcmdhd on May 25 2014 at 09:19:43 <6>bcmdhd: irq=170, flags=0x00000414 dhdsdio_probe : no mutex held. set lock F1 signature read @0x18000000=0x1591a962 bcmsdh_config_hw_oob_intr: Enter DHD: dongle ram size is set to 245760(orig 245760) dhd_attach, firmware path wl_create_event_handler thr:29b created wl_create_event_handler thr:29b started p2p0: P2P Interface Registered dhd_attach thr:29d created dhd_attach thr:29d started dhd_attach thr:29e created dhd_attach thr:29e started <3>bcm4330: exports duplicate symbol bcmsdh_probe (owned by bcmdhd) <3>bcm4330: exports duplicate symbol bcmsdh_probe (owned by bcmdhd) dhd_attach thr:29f created dhd_attach thr:29f started Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33 dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to insert WLAN RESET dhdsdio_probe : the lock is released. <6>sdio wifi power state: off =========== WLAN placed in RESET ======== <6>EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null) <6>Bluetooth: Core ver 2.16 <6>NET: Registered protocol family 31 <6>Bluetooth: HCI device and connection manager initialized <6>Bluetooth: HCI socket layer initialized <6>Bluetooth: L2CAP socket layer initialized <6>Bluetooth: SCO socket layer initialized <6>Bluetooth: RFCOMM TTY layer initialized <6>Bluetooth: RFCOMM socket layer initialized <6>Bluetooth: RFCOMM ver 1.11 <6>sunxi-rtc sunxi-rtc: actually set time to 2014-10-9 4:40:50 <6>EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) <6>[sw-ohci2]: shutdown start [sw-ohci2]: close clock <6>[sw-ohci2]: shutdown end <6>[sw-ehci2]: shutdown start [sw-ehci2]: Set USB Power OFF [sw-ehci2]: close clock <6>[sw-ehci2]: shutdown end <6>[sw-ohci1]: shutdown start [sw-ohci1]: close clock <6>[sw-ohci1]: shutdown end <6>[sw-ehci1]: shutdown start [sw-ehci1]: Set USB Power OFF [sw-ehci1]: close clock <6>[sw-ehci1]: shutdown end [NAND]shutdown nand try to shutdown 0 time Nand flash shutdown ok! <0>Restarting system. <6>[hotplug]: cpu(0) try to kill cpu(1) <3>[hotplug]: try to kill cpu:1 failed! U-Boot SPL 2014.01-rc1-09161-g108ec3f (Jan 20 2014 - 05:50:52) Board: Cubietruck DRAM: 2048 MiB CPU: 960000000Hz, AXI/AHB/APB: 3/2/2 spl: not an uImage at 1600 U-Boot 2014.01-rc1-09161-g108ec3f (Jan 20 2014 - 05:50:52) Allwinner Technology CPU: Allwinner A20 (SUN7I) Board: Cubietruck I2C: ready DRAM: 2 GiB WARNING: Caches not enabled MMC: SUNXI SD/MMC: 0 **\* Warning - bad CRC, using default environment In: serial Out: serial Err: serial Net: mii0 Warning: failed to set MAC address Hit any key to stop autoboot: 1  0 *\* Unrecognized filesystem type ** *\* File not found boot/uEnv.txt ** 150 bytes read in 13 ms (10.7 KiB/s) Loaded environment from uEnv.txt *\* Unrecognized filesystem type ** *\* File not found boot/boot.scr ** *\* File not found boot.scr ** *\* File not found /boot/script.bin ** *\* Unrecognized filesystem type ** 50028 bytes read in 16 ms (3 MiB/s) 5912576 bytes read in 430 ms (13.1 MiB/s) ## Booting kernel from Legacy Image at 48000000 ... Image Name: Linux-3.4.79-sun7i Created: 2014-07-02 22:40:15 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 5912512 Bytes = 5.6 MiB Load Address: 40008000 Entry Point: 40008000 Verifying Checksum ... OK Loading Kernel Image ... OK Starting kernel ... <6>Booting Linux on physical CPU 0 <6>Initializing cgroup subsys cpuset <6>Initializing cgroup subsys cpu <5>Linux version 3.4.79-sun7i (root@ubtu) (gcc version 4.8.2 20130603 (prerelease) (crosstool-NG linaro-1.13.1-4.8-2013.06 - Linaro GCC 2013.06) ) #14 SMP PREEMPT Thu Jul 3 06:39:51 CST 2014 CPU: ARMv7 Processor [410fc074] revision 4 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine: sun7i <6>Memory Reserved: <6> SYS : 0x43000000 - 0x4300ffff ( 64 kB) <6> G2D : 0x50000000 - 0x50ffffff ( 16 MB) <6> LCD : 0x51000000 - 0x52ffffff ( 32 MB) <7>cma: dma_contiguous_reserve(limit 4fffffff) <7>cma: dma_contiguous_reserve: reserving 192 MiB for global area <7>cma: dma_declare_contiguous(size c000000, base 00000000, limit 4fffffff) <6>cma: CMA: reserved 192 MiB at 43c00000 Memory policy: ECC disabled, Data cache writealloc <6>sunxi: Allwinner A20 (AW1651/sun7i) detected. <7>On node 0 totalpages: 524288 <7>free_area_init_node: node 0, pgdat c0b30500, node_mem_map d3000000 <7> DMA zone: 512 pages used for memmap <7> DMA zone: 0 pages reserved <7> DMA zone: 65024 pages, LIFO batch:15 <7> Normal zone: 1008 pages used for memmap <7> Normal zone: 128016 pages, LIFO batch:31 <7> HighMem zone: 2576 pages used for memmap <7> HighMem zone: 327152 pages, LIFO batch:31 <6>PERCPU: Embedded 7 pages/cpu @d400e000 s7616 r8192 d12864 u32768 <7>pcpu-alloc: s7616 r8192 d12864 u32768 alloc=8*4096 <7>pcpu-alloc: [0] 0 [0] 1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 520192 <5>Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 console=tty2 hdmi.audio=EDID:0 disp.screen0_output_mode=EDID:0 consoleblank=0 loglevel=0 <6>PID hash table entries: 4096 (order: 2, 16384 bytes) <6>Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) <6>Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) <6>allocated 4194304 bytes of page_cgroup <6>please try 'cgroup_disable=memory' option if you don't want memory cgroups <6>Memory: 2048MB = 2048MB total <5>Memory: 1816100k/1816100k available, 281052k reserved, 1318912K highmem <5>Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xf0000000 - 0xff000000 ( 240 MB) lowmem : 0xc0000000 - 0xef800000 ( 760 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0008000 - 0xc0a7b204 (10701 kB) .init : 0xc0a7c000 - 0xc0ab8dc0 ( 244 kB) .data : 0xc0aba000 - 0xc0b39398 ( 509 kB) .bss : 0xc0b393bc - 0xc0d21cd8 (1955 kB) <6>SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 <6>Preemptible hierarchical RCU implementation. <6> RCU dyntick-idle grace-period acceleration is enabled. <6>NR_IRQS:192 <6>Architected local timer running at 24.00MHz. <6>sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms <2>start_kernel(): bug: interrupts were enabled early <6>Console: colour dummy device 80x30 <6>console [tty2] enabled <6>Calibrating delay loop... 1915.28 BogoMIPS (lpj=9576448) <6>pid_max: default: 32768 minimum: 301 <6>Mount-cache hash table entries: 512 <6>Initializing cgroup subsys cpuacct <6>Initializing cgroup subsys memory <6>Initializing cgroup subsys devices <6>Initializing cgroup subsys freezer <6>Initializing cgroup subsys blkio <6>Initializing cgroup subsys perf_event <6>CPU: Testing write buffer coherency: ok <6>CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 <6>hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available <6>Setting up static identity map for 0x40788798 - 0x407887f0 CPU1: Booted secondary processor <6>CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 <6>Brought up 2 CPUs <6>SMP: Total of 2 processors activated (3830.57 BogoMIPS). <6>devtmpfs: initialized <6>xor: measuring software checksum speed <6> arm4regs : 1332.000 MB/sec <6> 8regs : 705.600 MB/sec <6> 32regs : 798.000 MB/sec <6>xor: using function: arm4regs (1332.000 MB/sec) <6>dummy: <7>cma: cma_init_reserved_areas() <7>cma: cma_create_area(base 00043c00, count c000) <7>cma: cma_create_area: returned ef0ab1c0 <6>NET: Registered protocol family 16 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 64, align 6) <7>cma: dma_alloc_from_contiguous(): returned d3078000 <6>DMA: preallocated 256 KiB pool for atomic coherent allocations <6>hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. <6>hw-breakpoint: maximum watchpoint size is 8 bytes. <6>[ccu-inf] aw clock manager init <6>[ccu-inf] aw_ccu_init <6>[ccu-inf] script config pll3 to 297MHz <6>[ccu-inf] script config pll4 to 300MHz <6>[ccu-inf] script config pll6 to 600MHz <6>[ccu-inf] script config pll7 to 297MHz <6>[ccu-inf] script config pll8 to 336MHz <6>Init eGon pin module V2.0 <6>bio: create slab at 0 raid6: int32x1 151 MB/s raid6: int32x2 189 MB/s raid6: int32x4 209 MB/s raid6: int32x8 196 MB/s raid6: using algorithm int32x4 (209 MB/s) <5>SCSI subsystem initialized <7>libata version 3.00 loaded. <6>usbcore: registered new interface driver usbfs <6>usbcore: registered new interface driver hub <6>usbcore: registered new device driver usb <6>Linux media interface: v0.10 <6>Linux video capture interface: v2.00 <6>Advanced Linux Sound Architecture Driver Version 1.0.25. <6>cfg80211: Calling CRDA to update world regulatory domain <6>Switching to clocksource arch_sys_counter <5>FS-Cache: Loaded <6>CacheFiles: Loaded WRN:L287(drivers/usb/sunxi_usb/manager/usb_manager.c):ERR: det_vbus pin is invaild WRN:L426(drivers/usb/sunxi_usb/manager/usb_manager.c):ERR: check_usb_board_info failed WRN:L480(drivers/usb/sunxi_usb/manager/usb_manager.c):ERR: get_usb_cfg failed <6>NET: Registered protocol family 2 <6>IP route cache hash table entries: 32768 (order: 5, 131072 bytes) <6>TCP established hash table entries: 131072 (order: 8, 1048576 bytes) <6>TCP bind hash table entries: 65536 (order: 7, 786432 bytes) <6>TCP: Hash tables configured (established 131072 bind 65536) <6>TCP: reno registered <6>UDP hash table entries: 512 (order: 2, 16384 bytes) <6>UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) <6>NET: Registered protocol family 1 <6>RPC: Registered named UNIX socket transport module. <6>RPC: Registered udp transport module. <6>RPC: Registered tcp transport module. <6>RPC: Registered tcp NFSv4.1 backchannel transport module. pm: select wifi: ap6210 <6>ap6xxx: config 32k clock [wifi_pm]: wifi gpio init is OK !! [rfkill]: rfkill set power 0 <6>audit: initializing netlink socket (disabled) <5>type=2000 audit(1.380:1): initialized highmem bounce pool size: 64 pages <5>VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) <5>NFS: Registering the id_resolver key type <6>nfs4filelayout_init: NFSv4 File Layout Driver Registering... <6>NTFS driver 2.1.30 [Flags: R/W]. <6>fuse init (API version 7.18) <6>OCFS2 1.5.0 <6>ocfs2: Registered cluster interface o2cb <6>OCFS2 DLMFS 1.5.0 OCFS2 User DLM kernel interface loaded <6>OCFS2 Node Manager 1.5.0 <6>OCFS2 DLM 1.5.0 <6>Btrfs loaded <6>msgmni has been set to 1355 <3>alg: comp: Compression test 1 failed for lzo-generic: output len = 57 <6>alg: No test for stdrng (krng) <6>Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) <6>io scheduler noop registered <6>io scheduler deadline registered <6>io scheduler cfq registered (default) <6>sunxi disp driver loaded (/dev/disp api 1.0) <6>Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled <6>[uart]: used uart info.: 0x05 <6>[uart]: serial probe 0 irq 33 mapbase 0x01c28000 <6>sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 33) is a U6_16550A <6>console [ttyS0] enabled <6>[uart]: serial probe 2 irq 35 mapbase 0x01c28800 <6>sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 35) is a U6_16550A <7>G2D: drv_g2d_init <6>G2D: g2dmem: g2d_start=50000000, g2d_size=1000000 <6>G2D: head:d0000000,tail:d1000000 <6>G2D: Module initialized.major:250 <6>brd: module loaded <6>loop: module loaded [NAND] nand driver version: 0x2 0x9 <4>Dev Sunxi softw311 nand magic does not match for MBR 1: softw411 <4>Dev Sunxi softw311 nand magic does not match for MBR 2: <4>Dev Sunxi softw311 nand magic does not match for MBR 3: <4>Dev Sunxi softw311 nand magic does not match for MBR 4: <4>Dev Sunxi softw311 nand header bad for all MBR copies, MBR corrupted or not present. <4>Dev Sunxi softw411 nand: part 1, start 128, size 2048 <4>Dev Sunxi softw411 nand: part 2, start 2176, size 15038336 <6> nand: nanda nandb [NAND]nand driver, ok. <6>sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP <4>sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1 <6>sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode <6>sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 23, align 5) <7>cma: dma_alloc_from_contiguous(): returned d3078800 <6>scsi0 : sw_ahci_platform <6>ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 88 <3>[spi-err] Get spi devices number failed <3>[spi-err] register spi devices board info failed <4>spi: cannot find any using configuration for all 4 spi controllers, return directly! <4>emac_init fetch emac using configuration failed <6>emac driver is disabled <6>gmac: use mac address from chipid <6>eth%d: device MAC address 02:0c:0a:41:75:44 [gmac]: sun6i_gmac platform driver registration completed <6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver <6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [sw-ehci1]: open clock [sw-ehci1]: Set USB Power ON <6>sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 1 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078ae0 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b00 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b20 <6>sw-ehci sw-ehci.1: irq 71, io mem 0x01c14000 <6>sw-ehci sw-ehci.1: USB 2.0 started, EHCI 1.00 <6>hub 1-0:1.0: USB hub found <6>hub 1-0:1.0: 1 port detected [sw-ohci1]: open clock <6>sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 2 <6>sw-ohci sw-ohci.1: irq 96, io mem 0x01c14400 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b40 ehci_irq: port change detect <6>hub 2-0:1.0: USB hub found <6>hub 2-0:1.0: 1 port detected [sw-ehci2]: open clock [sw-ehci2]: Set USB Power ON <6>sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver <6>sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 3 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b60 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078b80 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078ba0 <6>sw-ehci sw-ehci.2: irq 72, io mem 0x01c1c000 <6>ata1: SATA link down (SStatus 0 SControl 300) ehci_irq: port change detect <6>sw-ehci sw-ehci.2: USB 2.0 started, EHCI 1.00 ehci_irq: port change detect <6>hub 3-0:1.0: USB hub found <6>hub 3-0:1.0: 1 port detected [sw-ohci2]: open clock <6>sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver <6>sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 4 <6>sw-ohci sw-ohci.2: irq 97, io mem 0x01c1c400 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) The port change to OHCI now! <7>cma: dma_alloc_from_contiguous(): returned d3078bc0 <6>hub 4-0:1.0: USB hub found <6>hub 4-0:1.0: 1 port detected <6>Initializing USB Mass Storage driver... <6>usbcore: registered new interface driver usb-storage <6>USB Mass Storage support registered. <6>usbcore: registered new interface driver ums-alauda <6>usbcore: registered new interface driver ums-cypress <6>usbcore: registered new interface driver ums-datafab <6>usbcore: registered new interface driver ums_eneub6250 <6>usbcore: registered new interface driver ums-freecom <6>usbcore: registered new interface driver ums-isd200 <6>usbcore: registered new interface driver ums-jumpshot <6>usbcore: registered new interface driver ums-karma <6>usbcore: registered new interface driver ums-onetouch <6>usbcore: registered new interface driver ums-realtek <6>usbcore: registered new interface driver ums-sddr09 <6>usbcore: registered new interface driver ums-sddr55 <6>usbcore: registered new interface driver ums-usbat <6>usbcore: registered new interface driver usbserial <6>usbcore: registered new interface driver usbserial_generic <6>USB Serial support registered for generic <6>usb 2-1: new low-speed USB device number 2 using sw-ohci ehci_irq: port change detect The port change to OHCI now! <6>usbserial: USB Serial Driver core <6>mousedev: PS/2 mouse device common for all mice <6>sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0 <6>i2c /dev entries driver config i2c gpio with gpio_config api <6>axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected <6>axp_mfd 0-0034: AXP internal temperature monitoring enabled [AXP]axp driver uning configuration failed(342) [AXP]power_start = 0 <6>I2C: i2c-0: AW16XX I2C adapter <6>lirc_dev: IR Remote Control driver registered, major 249 <6>IR NEC protocol handler initialized <6>IR RC5(x) protocol handler initialized <6>IR RC6 protocol handler initialized <6>IR JVC protocol handler initialized <6>IR Sony protocol handler initialized <6>IR RC5 (streamzap) protocol handler initialized <6>IR SANYO protocol handler initialized <6>IR MCE Keyboard/mouse protocol handler initialized <6>IR LIRC bridge handler initialized [ace_drv] start!!! [ace_drv] init end!!! [pa_drv] start!!! [pa_drv] init end!!! <6>axp20_ldo1: 1300 mV <6>axp20_ldo2: 1800 <--> 3300 mV at 3000 mV <6>axp20_ldo3: 700 <--> 3500 mV at 2800 mV <6>axp20_ldo4: 1250 <--> 3300 mV at 2800 mV <6>axp20_buck2: 700 <--> 2275 mV at 1450 mV <6>axp20_buck3: 700 <--> 3500 mV at 1300 mV <6>axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV <6>input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.28/input/input0 <4>axp20_ldo2: Failed to create debugfs directory <6>md: linear personality registered for level -1 <6>md: raid0 personality registered for level 0 <6>md: raid1 personality registered for level 1 <6>md: raid10 personality registered for level 10 <6>md: raid6 personality registered for level 6 <6>md: raid5 personality registered for level 5 <6>md: raid4 personality registered for level 4 <6>md: multipath personality registered for level -4 <6>md: faulty personality registered for level -5 <6>device-mapper: uevent: version 1.0.3 <6>device-mapper: ioctl: 4.22.0-ioctl (2011-10-19) initialised: dm-devel@redhat.com <6>device-mapper: multipath: version 1.3.0 loaded <6>device-mapper: multipath round-robin: version 1.0.0 loaded <6>device-mapper: multipath queue-length: version 0.1.0 loaded <6>device-mapper: multipath service-time: version 0.2.0 loaded <6>device-mapper: dm-log-userspace: version 1.1.0 loaded <6>cpuidle: using governor ladder <6>cpuidle: using governor menu <6>usbcore: registered new interface driver ushc <6>[mmc-msg] sw_mci_init <6>[mmc-msg] get mmc2's IO(det) failed <6>[mmc-msg] Not using mmc2 due to script.bin parse failure <6>[mmc-msg] MMC host used card: 0xb, boot card: 0x0, io_card 8 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078be0 <6>[mmc-msg] sdc0 set round clock 400000, src 24000000 <6>[mmc-msg] sdc0 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 Probe: base:0xf00de000 irq:64 sg_cpu:c3c5f000(43c5f000) ret 0. <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c00 <6>[mmc-msg] sdc1 set round clock 400000, src 24000000 <6>usb 4-1: new low-speed USB device number 2 using sw-ohci <6>[mmc-msg] sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] mmc 0 detect change, present 1 <3>[mmc-err] update clock timeout, fatal error <6>[mmc-msg] sdc1 Probe: base:0xf00e0000 irq:65 sg_cpu:c3c60000(43c60000) ret 0. <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c20 <6>[mmc-msg] sdc3 set round clock 400000, src 24000000 <6>[mmc-msg] sdc3 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 Probe: base:0xf00e2000 irq:67 sg_cpu:c3c61000(43c61000) ret 0. [mmc_pm]: failed to fetch sdio card configuration! <6>sunxi_leds driver init <7>Registered led device: green:ph20:led1 <7>Registered led device: blue:ph21:led2 <6>ledtrig-cpu: registered to indicate activity on CPUs <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c40 <6>input: USB OPTICAL MOUSE as /devices/platform/sw-ohci.1/usb2/2-1/2-1:1.0/input/input1 <6>generic-usb 0003:15D9:0A4D.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-sw-ohci-1/input0 <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 1, align 0) <7>cma: dma_alloc_from_contiguous(): returned d3078c60 <6>input: Dell Dell USB Keyboard as /devices/platform/sw-ohci.2/usb4/4-1/4-1:1.0/input/input2 <6>generic-usb 0003:413C:2003.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Keyboard] on usb-sw-ohci-1/input0 <6>usbcore: registered new interface driver usbhid <6>usbhid: USB HID core driver <6>logger: created 256K log 'log_main' <6>logger: created 256K log 'log_events' <6>logger: created 256K log 'log_radio' <6>logger: created 256K log 'log_system' <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 8, align 3) <7>cma: dma_alloc_from_contiguous(): returned d3078d00 <6>IPv4 over IPv4 tunneling driver <6>TCP: bic registered <6>TCP: cubic registered <6>TCP: westwood registered <6>TCP: highspeed registered <6>TCP: hybla registered <6>TCP: htcp registered <6>TCP: vegas registered <6>TCP: veno registered <6>TCP: scalable registered <6>TCP: lp registered <6>TCP: yeah registered <6>TCP: illinois registered <6>Initializing XFRM netlink socket <6>NET: Registered protocol family 10 <6>NET: Registered protocol family 17 <6>NET: Registered protocol family 15 [mmc_pm]: No sdio card, please check your config !! <5>Registering the dns_resolver key type <6>VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 4 <5>Registering SWP/SWPB emulation handler <4>axp20_buck2: Failed to create debugfs directory <6>[cpu_freq] INF:-------------------V-F Table------------------- <6>[cpu_freq] INF: voltage = 1500mv frequency = 1056MHz <6>[cpu_freq] INF: voltage = 1450mv frequency = 1008MHz <6>[cpu_freq] INF: voltage = 1350mv frequency = 912MHz <6>[cpu_freq] INF: voltage = 1300mv frequency = 864MHz <6>[cpu_freq] INF: voltage = 1100mv frequency = 528MHz <6>[cpu_freq] INF: voltage = 1050mv frequency = 312MHz <6>[cpu_freq] INF: voltage = 1050mv frequency = 144MHz <6>[cpu_freq] INF: voltage = 1000mv frequency = 0MHz <6>[cpu_freq] INF:----------------------------------------------- <3>[cpu_freq] ERR:cpu max or min frequency from sysconfig is more than range <3>[cpu_freq] ERR:sunxi_cpufreq_initcall, use default cpu max/min frequency, max freq: 1008MHz, min freq: 60MHz <6>registered taskstats version 1 <4>[DISP] Invalid mode string: EDID:0, ignoring <6>[mmc-msg] sdc0 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 power on <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set round clock 400000, src 24000000 <3>[mmc-err] smc 0 err, cmd 52, RTO <3>[mmc-err] smc 0 err, cmd 52, RTO <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <3>[mmc-err] smc 0 err, cmd 5, RTO <3>[mmc-err] smc 0 err, cmd 5, RTO <3>[mmc-err] smc 0 err, cmd 5, RTO <3>[mmc-err] smc 0 err, cmd 5, RTO <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc0 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc0 set round clock 42857143, src 600000000 <6>[mmc-msg] sdc0 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B <6>mmc0: new high speed SDHC card at address 0002 <6>mmcblk0: mmc0:0002 7.52 GiB <6> mmcblk0: p1 p2 <6>Console: switching to colour frame buffer device 128x48 <6>I2C: i2c-1: HDMI I2C adapter <4>axp20_buck3: incomplete constraints, leaving on <4>axp20_buck2: incomplete constraints, leaving on <4>axp20_ldo4: incomplete constraints, leaving on <4>axp20_ldo3: incomplete constraints, leaving on <4>axp20_ldo2: incomplete constraints, leaving on <4>axp20_ldo1: incomplete constraints, leaving on <6>sunxi-rtc sunxi-rtc: setting system clock to 2014-10-09 04:41:11 UTC (1412829671) <6>ALSA device list: <6> #0: sunxi-CODEC Audio Codec <6>md: Waiting for all devices to be available before autodetect <6>md: If you don't use raid, use raid=noautodetect <6>md: Autodetecting RAID arrays. <6>md: Scanned 0 and added 0 devices. <6>md: autorun ... <6>md: ... autorun DONE. <3>EXT3-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240) <3>EXT2-fs (mmcblk0p2): error: couldn't mount because of unsupported optional features (240) <6>EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) <6>VFS: Mounted root (ext4 filesystem) on device 179:2. <6>devtmpfs: mounted <6>Freeing init memory: 240K <30>udevd[177]: starting version 175 <6>EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) <6>EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) <6>sunxi_gpio driver init ver 1.3 <6>gpiochip_add: registered GPIOs 1 to 67 on device: A1X_GPIO UMP<2>: Inserting UMP device driver. Compiled: May 25 2014, time: 09:11:38 UMP<2>: Using OS memory backend, allocation limit: 134217728 UMP: UMP device driver loaded Mali: permit MALI_IOC_MEM_MAP_EXT ioctl for framebuffer (paddr=0x51000000, size=33554432) <6>mali: use config clk_div 1 <6>mali: clk_div 1 Mali: mali clock set completed, clock is 312000000 Hz <6>mali: use config clk_div 1 <6>mali: clk_div 1 Mali: mali clock set completed, clock is 312000000 Hz <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 64, align 6) <7>cma: dma_alloc_from_contiguous(): returned d3079000 Mali: Mali device driver loaded <7>cma: dma_alloc_from_contiguous(cma ef0ab1c0, count 20480, align 8) <7>cma: dma_alloc_from_contiguous(): returned d307a000 [cedar dev]: install start!!! [cedar dev]: install end!!! <6>bcmdhd: got gpio2, mapped to irqno170 dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to turn on WL_REG_ON <6>sdio wifi power state: on <6>[mmc-msg] sdc3 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 power on <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 set round clock 400000, src 24000000 <3>[mmc-err] smc 3 err, cmd 52, RTO <3>[mmc-err] smc 3 err, cmd 52, RTO <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <3>[mmc-err] smc 3 err, cmd 8, RTO <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B <4>mmc2: queuing unknown CIS tuple 0x80 (2 bytes) <4>mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>mmc2: queuing unknown CIS tuple 0x80 (3 bytes) <4>mmc2: queuing unknown CIS tuple 0x80 (7 bytes) <6>[mmc-msg] sdc3 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B <6>[mmc-msg] sdc3 set round clock 42857143, src 600000000 <6>[mmc-msg] sdc3 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B <6>mmc2: new high speed SDIO card at address 0001 <3>bcm4330: exports duplicate symbol bcmsdh_probe (owned by bcmdhd) =========== WLAN placed in POWER ON ======== Linux Kernel SDIO/MMC Driver <6>bcmdhd: irq=170, flags=0x00000414 dhdsdio_probe : no mutex held. set lock F1 signature read @0x18000000=0x1591a962 bcmsdh_config_hw_oob_intr: Enter <3>bcm4330: exports duplicate symbol bcmsdh_probe (owned by bcmdhd) DHD: dongle ram size is set to 245760(orig 245760) dhd_attach, firmware path wl_create_event_handler thr:29c created wl_create_event_handler thr:29c started p2p0: P2P Interface Registered dhd_attach thr:29e created dhd_attach thr:29e started dhd_attach thr:2a0 created dhd_attach thr:2a0 started dhd_attach thr:2a3 created dhd_attach thr:2a3 started Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33 dhdsdio_probe : the lock is released. Dongle Host Driver, version 1.28.23.3 (r) Compiled in drivers/net/wireless/bcmdhd on May 25 2014 at 09:19:43 dhd_customer_gpio_wlan_ctrl: call customer specific GPIO to insert WLAN RESET <6>sdio wifi power state: off =========== WLAN placed in RESET ======== <4>------------[ cut here ]------------ <4>WARNING: at lib/list_debug.c:58 __list_del_entry+0x98/0xdc() list_del corruption. next->prev should be eeae9a8c, but was 0000009b Modules linked in: bcmdhd sunxi_cedar_mod mali ump gpio_sunxi [](unwind_backtrace+0x0/0x134) from [](warn_slowpath_common+0x54/0x64) [](warn_slowpath_common+0x54/0x64) from [](warn_slowpath_fmt+0x30/0x40) [](warn_slowpath_fmt+0x30/0x40) from [](__list_del_entry+0x98/0xdc) [](__list_del_entry+0x98/0xdc) from [](account_entity_dequeue+0x84/0x94) [](account_entity_dequeue+0x84/0x94) from [](dequeue_entity+0x94/0x240) [](dequeue_entity+0x94/0x240) from [](dequeue_task_fair+0x3c/0xe0) [](dequeue_task_fair+0x3c/0xe0) from [](__schedule+0x4fc/0x7d0) [](__schedule+0x4fc/0x7d0) from [](pipe_wait+0x64/0x8c) [](pipe_wait+0x64/0x8c) from [](pipe_read+0x3e4/0x584) [](pipe_read+0x3e4/0x584) from [](do_sync_read+0xc0/0x100) [](do_sync_read+0xc0/0x100) from [](vfs_read+0x98/0x174) [](vfs_read+0x98/0x174) from [](sys_read+0x38/0x78) [](sys_read+0x38/0x78) from [](ret_fast_syscall+0x0/0x30) <4>---[ end trace 00a884fd37e966bf ]--- <1>Unable to handle kernel NULL pointer dereference at virtual address 00000008 <1>pgd = ee7c8000 <1>[00000008] *pgd=6e61e831, *pte=00000000, *ppte=00000000 <0>Internal error: Oops: 17 [#1] PREEMPT SMP ARM Modules linked in: bcmdhd sunxi_cedar_mod mali ump gpio_sunxi CPU: 1 Tainted: G W (3.4.79-sun7i #14) PC is at rb_next+0x40/0x68 LR is at set_next_entity+0xb0/0xb8 pc : [] lr : [] psr: 20000093 sp : ee9a1d38 ip : 000004b8 fp : ee9a1e1c r10: c0ab86c0 r9 : ee9a0028 r8 : eeae9538 r7 : eeae9538 r6 : eeae9538 r5 : eeae9540 r4 : d4017710 r3 : 00000005 r2 : 00000004 r1 : eeae9538 r0 : eeae9540 Flags: nzCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment user Control: 10c5387d Table: 6e7c806a DAC: 00000015 PC: 0xc043a3e0: a3e0 15813004 e5902008 e3520000 15921000 12011003 11831001 15821000 e5902004 a400 e3520000 15921000 12011003 11831001 15821000 e8900007 e8830007 e12fff1e a420 e5903000 e3c32003 e1500002 0a000013 e5902004 e3520000 1a000001 ea000005 a440 e1a02003 e5923008 e3530000 1afffffb e1a00002 e12fff1e e1a02003 ea000004 a460 e5923004 e1500003 e1a00002 1afffff7 e5922000 e3d22003 1afffff8 eafffff3 a480 e3a00000 e12fff1e e92d4010 e1a04000 e5903004 e3530000 0a000008 e5902008 a4a0 e3520000 0a000003 ebffffdc e5903004 e3530000 0a000007 e1a00003 e8bd8010 a4c0 e5903008 e3530000 05903000 03c33003 e1a00003 e8bd8010 e5903000 e3c33003 LR: 0xc00634e0: 34e0 e5846030 e5962000 e5933038 e1530082 3a00000c e1c622d8 e1c603d8 e1c64ad8 3500 e0520000 e0c31001 e1510005 01500004 31a00004 31a01005 e1c60af8 e5862038 3520 e586303c e8bd8070 e5962028 e596302c eafffff9 ebfffa72 e594302c e2865008 3540 e1530005 0a000003 e1a00005 e2841028 eb0f5a83 eaffffdb e1a00005 eb0f5baf 3560 e584002c eafffff7 e92d43f8 e2806050 e5907058 e3570000 0a000046 e596802c 3580 e596703c e3580000 12488008 e1570008 11a07008 0a00002c e5961038 e3510000 35a0 0a00000d e1c823d0 e1c143d0 e0544002 e0c55003 e3540001 e2d53000 b1a07001 35c0 ba000005 e1a00008 ebfffe11 e3a01000 e1500004 e0d13005 a5967038 e5961034 SP: 0xee9a1cb8: 1cb8 c095e810 00000000 37e966bf 00a884fd d4017710 eeae9a8c 00000001 d40176c0 1cd8 c043a460 20000093 ffffffff ee9a1d24 eeae9538 c000e798 eeae9540 eeae9538 1cf8 00000004 00000005 d4017710 eeae9540 eeae9538 eeae9538 eeae9538 ee9a0028 1d18 c0ab86c0 ee9a1e1c 000004b8 ee9a1d38 c0063560 c043a460 20000093 ffffffff 1d38 eeae9a40 d40176c0 d4017710 c0063638 c0063568 eeae9a40 d40176c0 00000001 1d58 eeae9cd8 c0ab86c0 ee9a0028 c0786b74 d3fdd760 00000001 00000800 c00e4268 1d78 c0acc658 00000001 d3fdd760 c0ab86c0 00000001 00000001 c0ab86c0 c0ab86c0 1d98 c0ab86c0 c0ab86c0 00000000 c0787eb0 ee9a0028 c0ab86c0 00000040 00000001 FP: 0xee9a1d9c: 1d9c c0ab86c0 00000000 c0787eb0 ee9a0028 c0ab86c0 00000040 00000001 0000001f 1dbc ee61e000 eeb34734 ee61e07c 00000041 000000d0 00000000 00000001 c0b308c0 1ddc bf3c57df ee623898 0001f000 00000001 ee955800 00000000 c0788408 00000001 1dfc ee955800 eeae9a40 fffffdee 00000000 00000000 ee9a0000 ee955800 00000000 1e1c c00f271c bef51000 00000000 eeae9a40 c0052590 ee955808 ee955808 ee7c8000 1e3c eedbdb50 ee51e540 c00f2b28 00000001 eeb34740 ee9a1ea8 c0788408 00000000 1e5c 00000080 00000000 c005e5ec 00000000 ee51e540 eedbdbc0 ee955838 0000003b 1e7c ee9a1f88 ee51e540 fffffdee 00000000 00000000 eeae9a40 ffffffff 00000001 R0: 0xeeae94c0: 94c0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94e0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9500 00000000 ee7e4000 00000002 00400004 00000000 00000000 00000000 00000001 9520 00000078 00000078 00000078 00000000 c078be88 00000000 00000400 00400000 9540 00000005 00000000 00000000 00000000 0000009b 00000003 b6f49000 b6f2ed11 9560 00c7a99b 00000000 06f57010 00000001 00c6be18 00000000 00000000 00000000 9580 00000000 00000000 002318b4 00000000 00000004 00000000 002e402c 00000000 95a0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 R1: 0xeeae94b8: 94b8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94d8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94f8 00000000 00000000 00000000 ee7e4000 00000002 00400004 00000000 00000000 9518 00000000 00000001 00000078 00000078 00000078 00000000 c078be88 00000000 9538 00000400 00400000 00000005 00000000 00000000 00000000 0000009b 00000003 9558 b6f49000 b6f2ed11 00c7a99b 00000000 06f57010 00000001 00c6be18 00000000 9578 00000000 00000000 00000000 00000000 002318b4 00000000 00000004 00000000 9598 002e402c 00000000 00000000 00000000 00000000 00000000 00000000 00000000 R4: 0xd4017690: 7690 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 76b0 00000000 00000000 00000000 00000000 00000001 00000001 00000001 00000400 76d0 0000030c 00000241 0000026c 000002f5 ffff8fdf 00000000 00000000 00000000 76f0 00000000 00000000 00000400 00000000 0000029c 00000000 00001a59 00000000 7710 00000400 00000000 00000001 00000001 1260b952 00000001 06f57010 00000001 7730 06f57010 00000001 eeae9540 eeae9540 00000000 00000000 00000000 00000000 7750 00000146 d40176c0 00000001 d4017b50 d4017b50 c0bc9df0 00000400 00000000 7770 00000000 00000000 00000000 00000000 00000001 00000000 00000000 00000000 R5: 0xeeae94c0: 94c0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94e0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 9500 00000000 ee7e4000 00000002 00400004 00000000 00000000 00000000 00000001 9520 00000078 00000078 00000078 00000000 c078be88 00000000 00000400 00400000 9540 00000005 00000000 00000000 00000000 0000009b 00000003 b6f49000 b6f2ed11 9560 00c7a99b 00000000 06f57010 00000001 00c6be18 00000000 00000000 00000000 9580 00000000 00000000 002318b4 00000000 00000004 00000000 002e402c 00000000 95a0 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 R6: 0xeeae94b8: 94b8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94d8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94f8 00000000 00000000 00000000 ee7e4000 00000002 00400004 00000000 00000000 9518 00000000 00000001 00000078 00000078 00000078 00000000 c078be88 00000000 9538 00000400 00400000 00000005 00000000 00000000 00000000 0000009b 00000003 9558 b6f49000 b6f2ed11 00c7a99b 00000000 06f57010 00000001 00c6be18 00000000 9578 00000000 00000000 00000000 00000000 002318b4 00000000 00000004 00000000 9598 002e402c 00000000 00000000 00000000 00000000 00000000 00000000 00000000 R7: 0xeeae94b8: 94b8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94d8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94f8 00000000 00000000 00000000 ee7e4000 00000002 00400004 00000000 00000000 9518 00000000 00000001 00000078 00000078 00000078 00000000 c078be88 00000000 9538 00000400 00400000 00000005 00000000 00000000 00000000 0000009b 00000003 9558 b6f49000 b6f2ed11 00c7a99b 00000000 06f57010 00000001 00c6be18 00000000 9578 00000000 00000000 00000000 00000000 002318b4 00000000 00000004 00000000 9598 002e402c 00000000 00000000 00000000 00000000 00000000 00000000 00000000 R8: 0xeeae94b8: 94b8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94d8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 94f8 00000000 00000000 00000000 ee7e4000 00000002 00400004 00000000 00000000 9518 00000000 00000001 00000078 00000078 00000078 00000000 c078be88 00000000 9538 00000400 00400000 00000005 00000000 00000000 00000000 0000009b 00000003 9558 b6f49000 b6f2ed11 00c7a99b 00000000 06f57010 00000001 00c6be18 00000000 9578 00000000 00000000 00000000 00000000 002318b4 00000000 00000004 00000000 9598 002e402c 00000000 00000000 00000000 00000000 00000000 00000000 00000000 R9: 0xee99ffa8: ffa8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffc8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffe8 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000004 0008 00000000 eeae9a40 c0ad46c8 00000001 00000015 eeae9a40 d40176c0 eeae9500 0028 eeb34700 eeb35180 00000000 c0ab86c0 ee9a1e1c ee9a1d68 c0786da8 00000000 0048 00000000 00000000 00000000 00000000 01000000 00000000 b6f5d800 00000000 0068 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 0088 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 R10: 0xc0ab8640: 8640 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 8660 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 8680 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 86a0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 86c0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 86e0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 8700 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 8720 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 e7fddef0 <0>Process mountkernfs.sh (pid: 746, stack limit = 0xee9a02f0) <0>Stack: (0xee9a1d38 to 0xee9a2000) <0>1d20: eeae9a40 d40176c0 <0>1d40: d4017710 c0063638 c0063568 eeae9a40 d40176c0 00000001 eeae9cd8 c0ab86c0 <0>1d60: ee9a0028 c0786b74 d3fdd760 00000001 00000800 c00e4268 c0acc658 00000001 <0>1d80: d3fdd760 c0ab86c0 00000001 00000001 c0ab86c0 c0ab86c0 c0ab86c0 c0ab86c0 <0>1da0: 00000000 c0787eb0 ee9a0028 c0ab86c0 00000040 00000001 0000001f ee61e000 <0>1dc0: eeb34734 ee61e07c 00000041 000000d0 00000000 00000001 c0b308c0 bf3c57df <0>1de0: ee623898 0001f000 00000001 ee955800 00000000 c0788408 00000001 ee955800 <0>1e00: eeae9a40 fffffdee 00000000 00000000 ee9a0000 ee955800 00000000 c00f271c <0>1e20: bef51000 00000000 eeae9a40 c0052590 ee955808 ee955808 ee7c8000 eedbdb50 <0>1e40: ee51e540 c00f2b28 00000001 eeb34740 ee9a1ea8 c0788408 00000000 00000080 <0>1e60: 00000000 c005e5ec 00000000 ee51e540 eedbdbc0 ee955838 0000003b ee9a1f88 <0>1e80: ee51e540 fffffdee 00000000 00000000 eeae9a40 ffffffff 00000001 c00ea0d4 <0>1ea0: 00000000 00000000 bef4fde4 00000080 c0ab86c0 c00629c8 00000000 00000001 <0>1ec0: ffffffff ee51e540 00000000 00000000 00000000 00000000 eeae9a40 00000003 <0>1ee0: 00000000 00000000 00000000 00000000 00000000 c0ad14a8 00000080 ee9a1fb0 <0>1f00: 00000080 0001f2b4 01a47b44 c00083d4 c001cdc4 c0acf848 d400f6c0 d400f6c0 <0>1f20: c0acc658 eeaeadfc eeaeaa00 c0ab86c0 ee9a1f5c ee51e540 bef4fde4 ee9a0018 <0>1f40: ee9a1f88 00000080 ee9a0000 00000000 01a47b44 c00ea578 00000000 c0036614 <0>1f60: ee4c3540 00000000 00000000 ee51e540 bef4fde4 00000080 ee9a0000 c00eaa28 <0>1f80: 00000004 00000000 00000000 00000000 01a47c0f 0001f738 0001f42c 00000003 <0>1fa0: c000ed84 c000ec00 01a47c0f 0001f738 00000003 bef4fde4 00000080 00000001 <0>1fc0: 01a47c0f 0001f738 0001f42c 00000003 00000044 00015479 0001f2b4 01a47b44 <0>1fe0: 00000044 bef4fdc8 0000da99 b6eda3fc 60000010 00000003 ffff0021 0000008a [](rb_next+0x40/0x68) from [](set_next_entity+0xb0/0xb8) [](set_next_entity+0xb0/0xb8) from [](pick_next_task_fair+0xd0/0x138) [](pick_next_task_fair+0xd0/0x138) from [](__schedule+0x14c/0x7d0) [](__schedule+0x14c/0x7d0) from [](pipe_wait+0x64/0x8c) [](pipe_wait+0x64/0x8c) from [](pipe_read+0x3e4/0x584) [](pipe_read+0x3e4/0x584) from [](do_sync_read+0xc0/0x100) [](do_sync_read+0xc0/0x100) from [](vfs_read+0x98/0x174) [](vfs_read+0x98/0x174) from [](sys_read+0x38/0x78) [](sys_read+0x38/0x78) from [](ret_fast_syscall+0x0/0x30) <0>Code: e1a00002 e12fff1e e1a02003 ea000004 (e5923004)
nocolour commented 9 years ago

I facing same problem at first boot, system hang. After this I format the sd and burn again the image. 2nd try successful to boot it up.

michalliu commented 9 years ago

@nocolour Thank you for your clarification