search

daid / LegacyCura

Read this, it's important! NEW CURA DEVELOPMENT IS HAPPENING AT https://github.com/Ultimaker/Cura, this is the Cura 15.04 archive. Cura 2.1 and newer is on the Ultimaker github.
https://www.ultimaker.com/pages/our-software
584 stars 429 forks source link

Cura will not build supports where the support is needed #1431

Open Rdrost17 opened 8 years ago

Rdrost17 commented 8 years ago

I am trying to print a specific file that has an overhang on both sides about 0.125in from the base. One side will build supports the other will not. I have adjusted the support angles and everything but cannot make the software create supports. Any ideas?

Rdrost17 commented 8 years ago

part partnosupport

Rdrost17 commented 8 years ago

Does not work with "grid" supports either

BagelOrb commented 8 years ago

This problem is addressed in the next big Cura release. Op 10 mrt. 2016 21:59 schreef "Rdrost17" notifications@github.com:

I am trying to print a specific file that has an overhang on both sides about 0.125in from the base. One side will build supports the other will not. I have adjusted the support angles and everything but cannot make the software create supports. Any ideas?

— Reply to this email directly or view it on GitHub https://github.com/daid/Cura/issues/1431.

Rdrost17 commented 8 years ago

Do you know when this will be released?

BagelOrb commented 8 years ago

Could be a couple of weeks, could be a couple of months... Op 10 mrt. 2016 22:38 schreef "Rdrost17" notifications@github.com:

Do you know when this will be released?

— Reply to this email directly or view it on GitHub https://github.com/daid/Cura/issues/1431#issuecomment-195060268.

Ghostkeeper commented 8 years ago

Closed beta is going on right now. Public beta will be soon. Release is currently set for the end of the month.

fiberbug commented 8 years ago

I am having similar problems trying to print a spool and asking for supports? If I just print one side of the spool, the supports work good but when I try to print the entire spool and ask for supports, there are none?

BagelOrb commented 8 years ago

Try out the new beta release! The support system has had a total overhaul. Now it will place support in many places it wouldn't before. Op 3 mei 2016 16:55 schreef "fiberbug" notifications@github.com:

I am having similar problems trying to print a spool and asking for supports? If I just print one side of the spool, the supports work good but when I try to print the entire spool and ask for supports, there are none?

— You are receiving this because you commented. Reply to this email directly or view it on GitHub https://github.com/daid/Cura/issues/1431#issuecomment-216554513

fiberbug commented 8 years ago

Where do I go to get the New beta release?

fiberbug commented 8 years ago

Hi Tim,

Thanks for the response. Could you tell me how or where I should go to try the new beta release?

Tim Kuipers mailto:notifications@github.com Tuesday, May 03, 2016 3:42 PM Try out the new beta release! The support system has had a total overhaul. Now it will place support in many places it wouldn't before. Op 3 mei 2016 16:55 schreef "fiberbug" notifications@github.com:

I am having similar problems trying to print a spool and asking for supports? If I just print one side of the spool, the supports work good but when I try to print the entire spool and ask for supports, there are none?

— You are receiving this because you commented. Reply to this email directly or view it on GitHub https://github.com/daid/Cura/issues/1431#issuecomment-216554513

— You are receiving this because you commented. Reply to this email directly or view it on GitHub https://github.com/daid/Cura/issues/1431#issuecomment-216642900

nallath commented 8 years ago

http://software.ultimaker.com/Cura_open_beta/

Ghostkeeper commented 8 years ago

You can get it from the Ultimaker website with the smaller text below the main download button ("Download Cura 2.1.0 (beta)"). Or just download it from our open beta page.

fiberbug commented 8 years ago

Thank you!!

On May 4, 2016, at 3:50 AM, Ghostkeeper notifications@github.com wrote:

You can get it from the Ultimaker website with the smaller text below the main download button ("Download Cura 2.1.0 (beta)"). Or just download it from our open beta page.

— You are receiving this because you commented. Reply to this email directly or view it on GitHub