Open coyan opened 1 year ago
dangowrt
commented
1 year ago Most likely you are missing firmware files. If you were are using snapshot builds, this can happen because the firmware was previously included in kmod-mt7915e package and now was moved into a separate package kmod-mt7915-firmware. Installing kmod-mt7915-firmware should fix it.
coyan
commented
1 year ago I think that the package is installed by default:
Or you suggest that I install the "_openwrt-22.03.3-mediatek-mt7622-linksyse8450-squashfs-sysupgrade.bin" file located here? https://openwrt.org/toh/linksys/e8450
Sorry but I don't know where is the installer for kmod-mt7915-firmware :(
dangowrt
commented
1 year ago If you use OpenWrt 22.03 the firmware for MT7915 is part of kmod-mt7915e which you have installed.
Please share the complete system log, so I can see why the 5 GHz wifi is not detected.
Or you suggest that I install the "_openwrt-22.03.3-mediatek-mt7622-linksyse8450-squashfs-sysupgrade.bin" file located here?
No, using a non-UBI firmware file on the device after the bootloader has been switched to the UBI-aware version will brick your device. Don't do it.
coyan
commented
1 year ago I restarted the device (usin LuCi) and here are both logs:
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: started, version 2.86 cachesize 150
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: DNS service limited to local subnets
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq-dhcp[1]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for test
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for local
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: reading /tmp/resolv.conf.d/resolv.conf.auto
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using nameserver 1.1.1.1#53
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using nameserver 8.8.8.8#53
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for test
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for local
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: read /etc/hosts - 4 addresses
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 8 addresses
Tue Feb 21 20:45:25 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Tue Feb 21 20:45:25 2023 daemon.notice netifd: Wireless device 'radio0' is now up
Tue Feb 21 20:45:25 2023 kern.info kernel: [ 15.511109] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
Tue Feb 21 20:45:25 2023 kern.info kernel: [ 15.518658] br-lan: port 1(lan1) entered blocking state
Tue Feb 21 20:45:25 2023 kern.info kernel: [ 15.523894] br-lan: port 1(lan1) entered forwarding state
Tue Feb 21 20:45:25 2023 daemon.notice netifd: Network device 'lan1' link is up
Tue Feb 21 20:45:29 2023 daemon.info dnsmasq-dhcp[1]: DHCPDISCOVER(br-lan) 192.168.1.110 a5:47:f8:6e:55:10
Tue Feb 21 20:45:29 2023 daemon.info dnsmasq-dhcp[1]: DHCPOFFER(br-lan) 192.168.1.110 a5:47:f8:6e:55:10
Tue Feb 21 20:45:29 2023 daemon.info dnsmasq-dhcp[1]: DHCPREQUEST(br-lan) 192.168.1.110 a5:47:f8:6e:55:10
Tue Feb 21 20:45:29 2023 daemon.info dnsmasq-dhcp[1]: DHCPACK(br-lan) 192.168.1.110 a5:47:f8:6e:55:10 computer
Tue Feb 21 20:45:32 2023 daemon.notice hostapd: wlan0: ACS-COMPLETED freq=2427 channel=4
Tue Feb 21 20:45:32 2023 kern.info kernel: [ 22.292186] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Tue Feb 21 20:45:32 2023 kern.info kernel: [ 22.298674] br-lan: port 5(wlan0) entered blocking state
Tue Feb 21 20:45:32 2023 kern.info kernel: [ 22.304017] br-lan: port 5(wlan0) entered forwarding state
Tue Feb 21 20:45:32 2023 daemon.notice netifd: Network device 'wlan0' link is up
Tue Feb 21 20:45:32 2023 daemon.notice hostapd: wlan0: interface state ACS->ENABLED
Tue Feb 21 20:45:32 2023 daemon.notice hostapd: wlan0: AP-ENABLED
Tue Feb 21 20:45:33 2023 daemon.info dnsmasq-dhcp[1]: {Redacted some DHCP discoveries}
Tue Feb 21 20:46:23 2023 user.info : luci: accepted login on / for root from 192.168.1.112[ 0.000000] Linux version 5.10.146 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 11.2.0 r19777-2853b6d652) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Fri Oct 7 23:34:56 2022
[ 0.000000] Machine model: Linksys E8450 (UBI)
[ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
[ 0.000000] printk: bootconsole [uart8250] enabled
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
[ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
[ 0.000000] node 0: [mem 0x0000000043030000-0x000000005fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] DMA zone: 2048 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 131072 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.2
[ 0.000000] percpu: Embedded 20 pages/cpu s43992 r8192 d29736 u81920
[ 0.000000] pcpu-alloc: s43992 r8192 d29736 u81920 alloc=20*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
[ 0.000000] CPU features: detected: ARM erratum 843419
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024
[ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512
[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[ 0.000000] Memory: 494120K/524288K available (8254K kernel code, 894K rwdata, 1444K rodata, 448K init, 299K bss, 30168K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: GICv2 detected, but range too small and irqchip.gicv2_force_probe not set
[ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
[ 0.000003] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
[ 0.008521] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
[ 0.019252] pid_max: default: 32768 minimum: 301
[ 0.024110] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.031689] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
[ 0.040741] rcu: Hierarchical SRCU implementation.
[ 0.045842] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build
[ 0.054084] smp: Bringing up secondary CPUs ...
[ 0.059135] Detected VIPT I-cache on CPU1
[ 0.059143] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000000bebc20, CPU1: 0x00000000000000
[ 0.059160] CPU features: Unsupported CPU feature variation detected.
[ 0.059192] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.059259] smp: Brought up 1 node, 2 CPUs
[ 0.093243] SMP: Total of 2 processors activated.
[ 0.098110] CPU features: detected: 32-bit EL0 Support
[ 0.103430] CPU features: detected: CRC32 instructions
[ 0.108862] CPU: All CPU(s) started at EL2
[ 0.113105] alternatives: patching kernel code
[ 0.121190] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.131410] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
[ 0.138524] pinctrl core: initialized pinctrl subsystem
[ 0.145259] NET: Registered protocol family 16
[ 0.150190] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.157542] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.165580] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.174129] thermal_sys: Registered thermal governor 'fair_share'
[ 0.174136] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.180448] thermal_sys: Registered thermal governor 'step_wise'
[ 0.186699] thermal_sys: Registered thermal governor 'user_space'
[ 0.193197] ASID allocator initialised with 65536 entries
[ 0.205628] pstore: Registered ramoops as persistent store backend
[ 0.212066] ramoops: using 0x10000@0x42ff0000, ecc: 0
[ 0.247465] cryptd: max_cpu_qlen set to 1000
[ 0.254289] SCSI subsystem initialized
[ 0.258873] libata version 3.00 loaded.
[ 0.263098] usbcore: registered new interface driver usbfs
[ 0.268822] usbcore: registered new interface driver hub
[ 0.274414] usbcore: registered new device driver usb
[ 0.281694] clocksource: Switched to clocksource arch_sys_counter
[ 0.288695] NET: Registered protocol family 2
[ 0.293386] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
[ 0.302082] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.310760] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.318826] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 0.326281] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.332951] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.339721] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.347063] NET: Registered protocol family 1
[ 0.351588] PCI: CLS 0 bytes, default 64
[ 0.358307] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[ 0.367601] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.373674] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.415148] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.423361] mtk-tphy 1a0c4000.usb-phy: failed to get ref_clk(id-1)
[ 0.435383] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
[ 0.457282] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
[ 0.465956] printk: console [ttyS0] disabled
[ 0.490586] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 22, base_baud = 1562500) is a ST16650V2
[ 0.500086] printk: console [ttyS0] enabled
[ 0.508455] printk: bootconsole [uart8250] disabled
[ 0.539019] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 23, base_baud = 1562500) is a ST16650V2
[ 0.549019] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 27, base_baud = 17499995) is a MediaTek BTIF
[ 0.558756] serial serial0: tty port ttyS2 registered
[ 0.564632] mtk_rng 1020f000.rng: registered RNG driver
[ 0.564808] random: crng init done
[ 0.570110] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.582486] loop: module loaded
[ 0.585632] Loading iSCSI transport class v2.0-870.
[ 0.592437] mtk-snand 1100d000.snfi: chip is FM35Q1GA, size 128MB, page size 2048, oob size 64
[ 0.601256] 4 fixed-partitions partitions found on MTD device 1100d000.snfi
[ 0.608269] OF: Bad cell count for /snfi@1100d000/partitions
[ 0.613941] OF: Bad cell count for /snfi@1100d000/partitions
[ 0.620035] Creating 4 MTD partitions on "1100d000.snfi":
[ 0.625454] 0x000000000000-0x000000080000 : "bl2"
[ 0.631042] 0x000000080000-0x0000001c0000 : "fip"
[ 0.637406] 0x0000001c0000-0x0000002c0000 : "factory"
[ 0.643912] 0x000000300000-0x000008000000 : "ubi"
[ 0.775823] blk_update_request: I/O error, dev mtdblock2, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 0.786198] Buffer I/O error on dev mtdblock2, logical block 0, async page read
[ 0.793665] blk_update_request: I/O error, dev mtdblock2, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 0.804012] Buffer I/O error on dev mtdblock2, logical block 0, async page read
[ 0.811452] blk_update_request: I/O error, dev mtdblock2, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0
[ 0.821808] Buffer I/O error on dev mtdblock2, logical block 0, async page read
[ 0.829109] mtdblock2: unable to read partition table
[ 0.863891] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc011ca0000, irq 37
[ 0.874711] i2c /dev entries driver
[ 0.879483] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
[ 0.890902] NET: Registered protocol family 10
[ 0.896112] Segment Routing with IPv6
[ 0.899815] NET: Registered protocol family 17
[ 0.904311] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
[ 0.917417] 8021q: 802.1Q VLAN Support v1.8
[ 0.922812] pstore: Using crash dump compression: deflate
[ 0.938054] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
[ 0.944613] mtk-pcie 1a143000.pcie: Parsing ranges property...
[ 0.950448] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
[ 0.975029] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
[ 0.981218] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.986713] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
[ 0.993588] pci_bus 0000:00: scanning bus
[ 0.997634] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
[ 1.003668] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
[ 1.012556] pci_bus 0000:00: fixups for bus
[ 1.016744] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
[ 1.023448] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 1.031456] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
[ 1.038293] pci_bus 0000:01: scanning bus
[ 1.042525] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280
[ 1.048704] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
[ 1.056028] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
[ 1.063352] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
[ 1.071313] pci 0000:01:00.0: supports D1 D2
[ 1.075579] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 1.082215] pci 0000:01:00.0: PME# disabled
[ 1.086700] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
[ 1.133083] pci_bus 0000:01: fixups for bus
[ 1.137271] pci_bus 0000:01: bus scan returning with max=01
[ 1.142854] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[ 1.149465] pci_bus 0000:00: bus scan returning with max=01
[ 1.155052] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
[ 1.162704] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
[ 1.170699] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
[ 1.177486] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
[ 1.185312] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
[ 1.193138] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
[ 1.200954] pci 0000:00:00.0: PCI bridge to [bus 01]
[ 1.205920] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
[ 1.212800] pcieport 0000:00:00.0: of_irq_parse_pci: failed with rc=-22
[ 1.219404] pcieport 0000:00:00.0: assign IRQ: got 0
[ 1.224377] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
[ 1.230480] pcieport 0000:00:00.0: enabling bus mastering
[ 1.236422] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges:
[ 1.242975] mtk-pcie 1a145000.pcie: Parsing ranges property...
[ 1.248809] mtk-pcie 1a145000.pcie: MEM 0x0028000000..0x002fffffff -> 0x0028000000
[ 1.357000] mtk-pcie 1a145000.pcie: Port1 link down
[ 1.362019] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00
[ 1.368196] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 1.373687] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff]
[ 1.380554] pci_bus 0001:00: scanning bus
[ 1.385777] pci_bus 0001:00: fixups for bus
[ 1.389954] pci_bus 0001:00: bus scan returning with max=00
[ 1.395868] mtk_hsdma 1b007000.dma-controller: Using 3 as missing dma-requests property
[ 1.404141] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
[ 1.461795] mt7530 mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=145)
[ 1.481645] mt7530 mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=146)
[ 1.501515] mt7530 mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=147)
[ 1.521395] mt7530 mdio-bus:00 lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=148)
[ 1.541456] mt7530 mdio-bus:00 wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=149)
[ 1.553182] mt7530 mdio-bus:00: configuring for fixed/2500base-x link mode
[ 1.560255] DSA: tree 0 setup
[ 1.560431] mt7530 mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 1.564066] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 1.575735] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1
[ 1.584843] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010
[ 1.593932] xhci-mtk 1a0c0000.usb: irq 31, io mem 0x1a0c0000
[ 1.600070] hub 1-0:1.0: USB hub found
[ 1.603869] hub 1-0:1.0: 2 ports detected
[ 1.608158] xhci-mtk 1a0c0000.usb: xHCI Host Controller
[ 1.613409] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2
[ 1.620808] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed
[ 1.627117] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.635540] hub 2-0:1.0: USB hub found
[ 1.639311] hub 2-0:1.0: 1 port detected
[ 1.644370] UBI: auto-attach mtd3
[ 1.647696] ubi0: attaching mtd3
[ 2.034282] ubi0: scanning is finished
[ 2.042363] ubi0: attached mtd3 (name "ubi", size 125 MiB)
[ 2.047851] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[ 2.054742] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[ 2.061521] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[ 2.068481] ubi0: good PEBs: 1000, bad PEBs: 0, corrupted PEBs: 0
[ 2.074569] ubi0: user volume: 6, internal volumes: 1, max. volumes count: 128
[ 2.081787] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 411290390
[ 2.090822] ubi0: available PEBs: 0, total reserved PEBs: 1000, PEBs reserved for bad PEB handling: 20
[ 2.100184] ubi0: background thread "ubi_bgt0d" started, PID 852
[ 2.107163] FIT: Default configuration: "config-1" (OpenWrt linksys_e8450-ubi)
[ 2.114425] FIT: kernel sub-image 0x00001000..0x004da08d "kernel-1" (ARM64 OpenWrt Linux-5.10.146)
[ 2.124348] FIT: flat_dt sub-image 0x004db000..0x004e2578 "fdt-1" (ARM64 OpenWrt linksys_e8450-ubi device tree blob)
[ 2.135745] FIT: filesystem sub-image 0x004e3000..0x009cafff "rootfs-1" (ARM64 OpenWrt linksys_e8450-ubi rootfs)
[ 2.146531] FIT: selecting configured loadable "rootfs-1" to be root filesystem
[ 2.153839] ubiblock0_4: p1(rootfs-1)
[ 2.154169] block ubiblock0_4: created from ubi0:4(fit)
[ 2.166875] VFS: Mounted root (squashfs filesystem) readonly on device 259:1.
[ 2.174270] Freeing unused kernel memory: 448K
[ 2.231764] Run /sbin/init as init process
[ 2.235852] with arguments:
[ 2.238810] /sbin/init
[ 2.241506] with environment:
[ 2.244645] HOME=/
[ 2.246995] TERM=linux
[ 2.420542] init: Console is alive
[ 2.424144] init: - watchdog -
[ 2.696405] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.715076] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 2.730005] init: - preinit -
[ 2.989518] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 2.998086] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 3.007101] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 3.014059] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
[ 3.021159] 8021q: adding VLAN 0 to HW filter on device lan1
[ 4.461961] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 4.469646] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
[ 7.079554] UBIFS (ubi0:5): Mounting in unauthenticated mode
[ 7.085351] UBIFS (ubi0:5): background thread "ubifs_bgt0_5" started, PID 931
[ 7.108794] UBIFS (ubi0:5): recovery needed
[ 7.167455] UBIFS (ubi0:5): recovery completed
[ 7.171987] UBIFS (ubi0:5): UBIFS: mounted UBI device 0, volume 5, name "rootfs_data"
[ 7.179814] UBIFS (ubi0:5): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[ 7.189737] UBIFS (ubi0:5): FS size: 92438528 bytes (88 MiB, 728 LEBs), journal size 4571136 bytes (4 MiB, 36 LEBs)
[ 7.200167] UBIFS (ubi0:5): reserved for root: 4366099 bytes (4263 KiB)
[ 7.206780] UBIFS (ubi0:5): media format: w5/r0 (latest is w5/r0), UUID 5BF2FBF3-7772-41B7-B4DB-DD095B1BD1F1, small LPT model
[ 7.220100] mount_root: switching to ubifs overlay
[ 7.227627] overlayfs: "xino" feature enabled using 2 upper inode bits.
[ 7.237550] urandom-seed: Seeding with /etc/urandom.seed
[ 7.307417] mt7530 mdio-bus:00 lan1: Link is Down
[ 7.316695] procd: - early -
[ 7.319653] procd: - watchdog -
[ 7.869942] procd: - watchdog -
[ 7.873966] procd: - ubus -
[ 7.928200] procd: - init -
[ 8.164305] urngd: v1.0.2 started.
[ 8.214986] kmodloader: loading kernel modules from /etc/modules.d/*
[ 8.231527] Loading modules backported from Linux version v5.15.58-0-g7d8048d4e064
[ 8.239126] Backport generated by backports.git v5.15.58-1-0-g42a95ce7
[ 8.295292] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 8.307829] mt7915e 0000:01:00.0: assign IRQ: got 150
[ 8.312994] pci 0000:00:00.0: enabling bus mastering
[ 8.317977] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
[ 8.324119] mt7915e 0000:01:00.0: enabling bus mastering
[ 8.348814] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
[ 8.348814]
[ 8.435484] mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834
[ 8.525121] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20211222184017a
[ 8.525121]
[ 8.652499] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20211222184052
[ 8.713939] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20211222184111
[ 8.830075] mtk-snand 1100d000.snfi: ECC: Uncorrectable bitflips in page 907 sect 3
[ 8.837751] mt7915e 0000:01:00.0: reading EEPROM from mtd factory failed: -74
[ 8.881036] mt7915e 0000:01:00.0: eeprom load fail, use default bin
[ 8.887388] mt7915e 0000:01:00.0: Direct firmware load for mediatek/mt7915_eeprom.bin failed with error -2
[ 8.897043] mt7915e 0000:01:00.0: Falling back to sysfs fallback for: mediatek/mt7915_eeprom.bin
[ 8.912507] mt7915e: probe of 0000:01:00.0 failed with error -12
[ 8.938094] PPP generic driver version 2.4.2
[ 8.943238] NET: Registered protocol family 24
[ 8.951988] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 12.418159] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
[ 12.427142] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
[ 12.435680] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
[ 12.444438] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 12.453575] mt7530 mdio-bus:00 lan1: configuring for phy/gmii link mode
[ 12.462993] 8021q: adding VLAN 0 to HW filter on device lan1
[ 12.473790] br-lan: port 1(lan1) entered blocking state
[ 12.479028] br-lan: port 1(lan1) entered disabled state
[ 12.485039] device lan1 entered promiscuous mode
[ 12.489659] device eth0 entered promiscuous mode
[ 12.503312] mt7530 mdio-bus:00 lan2: configuring for phy/gmii link mode
[ 12.510493] 8021q: adding VLAN 0 to HW filter on device lan2
[ 12.523058] br-lan: port 2(lan2) entered blocking state
[ 12.528287] br-lan: port 2(lan2) entered disabled state
[ 12.535459] mt7530 mdio-bus:00 lan2: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.543402] device lan2 entered promiscuous mode
[ 12.550941] br-lan: port 2(lan2) entered blocking state
[ 12.556240] br-lan: port 2(lan2) entered forwarding state
[ 12.566816] mt7530 mdio-bus:00 lan3: configuring for phy/gmii link mode
[ 12.575863] 8021q: adding VLAN 0 to HW filter on device lan3
[ 12.586152] mt7530 mdio-bus:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
[ 12.596162] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 12.605162] br-lan: port 3(lan3) entered blocking state
[ 12.610400] br-lan: port 3(lan3) entered disabled state
[ 12.618556] device lan3 entered promiscuous mode
[ 12.625704] br-lan: port 3(lan3) entered blocking state
[ 12.630937] br-lan: port 3(lan3) entered forwarding state
[ 12.642141] mt7530 mdio-bus:00 lan4: configuring for phy/gmii link mode
[ 12.649914] 8021q: adding VLAN 0 to HW filter on device lan4
[ 12.660342] mt7530 mdio-bus:00 lan4: Link is Up - 1Gbps/Full - flow control off
[ 12.670189] br-lan: port 4(lan4) entered blocking state
[ 12.675482] br-lan: port 4(lan4) entered disabled state
[ 12.682703] device lan4 entered promiscuous mode
[ 12.689722] br-lan: port 4(lan4) entered blocking state
[ 12.695003] br-lan: port 4(lan4) entered forwarding state
[ 12.708338] mt7530 mdio-bus:00 wan: configuring for phy/gmii link mode
[ 12.715597] 8021q: adding VLAN 0 to HW filter on device wan
[ 12.729508] mt7530 mdio-bus:00 wan: Link is Up - 1Gbps/Full - flow control off
[ 12.736847] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
[ 14.423534] br-lan: port 5(wlan0) entered blocking state
[ 14.428857] br-lan: port 5(wlan0) entered disabled state
[ 14.434508] device wlan0 entered promiscuous mode
[ 15.511109] mt7530 mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
[ 15.518658] br-lan: port 1(lan1) entered blocking state
[ 15.523894] br-lan: port 1(lan1) entered forwarding state
[ 22.292186] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 22.298674] br-lan: port 5(wlan0) entered blocking state
[ 22.304017] br-lan: port 5(wlan0) entered forwarding stateI changed the MAC for a fake one and deleted the DHCP assigments.
dangowrt
commented
1 year ago [ 8.830075] mtk-snand 1100d000.snfi: ECC: Uncorrectable bitflips in page 907 sect 3
[ 8.837751] mt7915e 0000:01:00.0: reading EEPROM from mtd factory failed: -74
[ 8.881036] mt7915e 0000:01:00.0: eeprom load fail, use default bin
[ 8.887388] mt7915e 0000:01:00.0: Direct firmware load for mediatek/mt7915_eeprom.bin failed with error -2
[ 8.897043] mt7915e 0000:01:00.0: Falling back to sysfs fallback for: mediatek/mt7915_eeprom.bin
[ 8.912507] mt7915e: probe of 0000:01:00.0 failed with error -12This is a symptom of the updated SPI-NAND driver and was discussed in https://github.com/dangowrt/owrt-ubi-installer/issues/27
Please also share your U-Boot version using fw_printenv ver, as that will tell the version of the installer which you were using originally. If the version is older than U-Boot 2021.10, the easiest way to fix the issue is to re-run the (now updated) installer which will take care of fixing this issue:
sysupgrade -F https://github.com/dangowrt/owrt-ubi-installer/releases/download/v1.0.1/openwrt-22.03.1-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery-installer.itbIf you are already on U-Boot 2021.10 or newer then we are dealing with a different problem and in this case please dump the EEPROM data from flash using hexdump -C /dev/mtdblock2 and we shall analyze if it still looks good despite the supposed bit-flips and if so re-write it to fix them.
nazarewk
commented
1 year ago @dangowrt I had similar issue: over the last few days/weeks I've observed degraded internet performance (most likely WIFI-only) until it stopped working after i came back from holiday. I remember some error about PHY not present in system logs after attempting reboot to fix the issue first.
Re-installing firmware and reloading backup fixed the issue with inactive radios.
wallrik
commented
1 year ago Anyone coming to this issue with 5G not working after an update. I just had this issue as well. However, my error seemed to be different from this issue author. My kernel log:
[ 7.425237] mt7915e 0000:01:00.0: assign IRQ: got 146
[ 7.430379] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
[ 7.436473] mt7915e 0000:01:00.0: enabling bus mastering
[ 7.558408] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44e3d0c0
[ 7.578530] mt7915e 0000:01:00.0: Direct firmware load for mediatek/mt7915_rom_patch.bin failed with error -2
[ 7.588492] mt7915e 0000:01:00.0: Falling back to sysfs fallback for: mediatek/mt7915_rom_patch.bin
[ 7.874302] mt7915e: probe of 0000:01:00.0 failed with error -12I was able to fix this by installing kmod-mt7915-firmware from software packages and rebooting 👌
wit-know
commented
9 months ago I too have the very same problem outlined by the OP. I have a brand new E8450 that I unwrapped yesterday and tested. Then, after reading all the text on the UBI installer, I uploaded the installer and then flashed the current 23.05.0 firmware. I'll admit that I uploaded the wrong installer initially (using the newest 1.1.1 version), but then reread everything and attempted to install the 23.05.0 firmware again. I am now confident I have the 23.05.0 firmware installed correctly.
HOWEVER, just like OP's screenshot above, I only have radio0 available, and the 5GHz radio1 is not being detected. My log looks like this:
root@OpenWrt:~# logread
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.000000] Linux version 5.15.134 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r23497-6637af95aa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Mon Oct 9 21:45:35 2023
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Machine model: Linksys E8450 (UBI)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] earlycon: uart8250 at MMIO32 0x0000000011002000 (options '')
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] printk: bootconsole [uart8250] enabled
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Zone ranges:
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] DMA32 empty
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Normal empty
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Movable zone start for each node
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Early memory node ranges
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000042ffffff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000043000000-0x000000004302ffff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] node 0: [mem 0x0000000043030000-0x000000005fffffff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] psci: probing for conduit method from DT.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] psci: PSCIv1.1 detected in firmware.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] psci: Using standard PSCI v0.2 function IDs
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] psci: SMC Calling Convention v1.4
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] percpu: Embedded 17 pages/cpu s30040 r8192 d31400 u69632
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 0.000000] pcpu-alloc: s30040 r8192 d31400 u69632 alloc=17*4096
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Detected VIPT I-cache on CPU0
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] CPU features: kernel page table isolation disabled by kernel configuration
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] CPU features: detected: ARM erratum 843419
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 129024
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.000000] Kernel command line: earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Memory: 502064K/524288K available (8384K kernel code, 904K rwdata, 1416K rodata, 448K init, 308K bss, 22224K reserved, 0K cma-reserved)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] rcu: Hierarchical RCU implementation.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Tracing variant of Tasks RCU enabled.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] Root IRQ handler: 0xffffffc008423cb4
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] GIC: Using split EOI/Deactivate mode
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] arch_timer: cp15 timer(s) running at 12.50MHz (phys).
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x2e2049cda, max_idle_ns: 440795202628 ns
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.000001] sched_clock: 56 bits at 12MHz, resolution 80ns, wraps every 4398046511080ns
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.008238] Calibrating delay loop (skipped), value calculated using timer frequency.. 25.00 BogoMIPS (lpj=125000)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.018637] pid_max: default: 32768 minimum: 301
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.023550] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.030896] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.040024] rcu: Hierarchical SRCU implementation.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.045299] smp: Bringing up secondary CPUs ...
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.050200] Detected VIPT I-cache on CPU1
Mon Oct 9 21:45:37 2023 kern.warn kernel: [ 0.050210] CPU features: SANITY CHECK: Unexpected variation in SYS_CNTFRQ_EL0. Boot CPU: 0x00000000bebc20, CPU1: 0x00000000000000
Mon Oct 9 21:45:37 2023 kern.warn kernel: [ 0.050230] CPU features: Unsupported CPU feature variation detected.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.050260] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.050330] smp: Brought up 1 node, 2 CPUs
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.083254] SMP: Total of 2 processors activated.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.087970] CPU features: detected: 32-bit EL0 Support
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.093126] CPU features: detected: CRC32 instructions
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.098310] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.106754] CPU: All CPU(s) started at EL2
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.110866] alternatives: patching kernel code
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.119763] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.129667] futex hash table entries: 512 (order: 3, 32768 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.136627] pinctrl core: initialized pinctrl subsystem
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.142743] NET: Registered PF_NETLINK/PF_ROUTE protocol family
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.149018] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.156151] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.163941] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.172177] thermal_sys: Registered thermal governor 'fair_share'
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.172180] thermal_sys: Registered thermal governor 'bang_bang'
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.178292] thermal_sys: Registered thermal governor 'step_wise'
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.184323] thermal_sys: Registered thermal governor 'user_space'
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.190551] ASID allocator initialised with 65536 entries
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.202455] pstore: Registered ramoops as persistent store backend
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.208665] ramoops: using 0x10000@0x42ff0000, ecc: 0
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.235332] cryptd: max_cpu_qlen set to 1000
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.242289] SCSI subsystem initialized
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 0.246256] libata version 3.00 loaded.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.251393] clocksource: Switched to clocksource arch_sys_counter
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.258135] NET: Registered PF_INET protocol family
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.263180] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.270917] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.279352] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.287137] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.294938] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.302149] TCP: Hash tables configured (established 4096 bind 4096)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.308613] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.315180] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.322331] NET: Registered PF_UNIX/PF_LOCAL protocol family
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.328027] PCI: CLS 0 bytes, default 64
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.334571] workingset: timestamp_bits=46 max_order=17 bucket_order=0
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.344687] squashfs: version 4.0 (2009/01/31) Phillip Lougher
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.350553] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.392750] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
Mon Oct 9 21:45:37 2023 kern.err kernel: [ 0.401337] mt7622-pinctrl 10211000.pinctrl: invalid group "pwm_ch7_2" for function "pwm"
Mon Oct 9 21:45:37 2023 kern.err kernel: [ 0.414121] mt-pmic-pwrap 10001000.pwrap: unexpected interrupt int=0x1
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.429097] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.437812] printk: console [ttyS0] disabled
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.462302] 11002000.serial: ttyS0 at MMIO 0x11002000 (irq = 125, base_baud = 1562500) is a ST16650V2
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.471631] printk: console [ttyS0] enabled
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.479995] printk: bootconsole [uart8250] disabled
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.510567] 11004000.serial: ttyS1 at MMIO 0x11004000 (irq = 126, base_baud = 1562500) is a ST16650V2
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.520682] 1100c000.serial: ttyS2 at MMIO 0x1100c000 (irq = 130, base_baud = 17499995) is a MediaTek BTIF
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.530508] serial serial0: tty port ttyS2 registered
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.536318] mtk_rng 1020f000.rng: registered RNG driver
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.536517] random: crng init done
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.548432] loop: module loaded
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.551639] Loading iSCSI transport class v2.0-870.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.557746] mtk-ecc 1100e000.ecc: probed
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.565552] spi-nand spi2.0: Winbond SPI NAND was found.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.570874] spi-nand spi2.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.579052] mtk-snand 1100d000.spi: ECC strength: 4 bits per 512 bytes
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.585886] 4 fixed-partitions partitions found on MTD device spi2.0
Mon Oct 9 21:45:37 2023 kern.err kernel: [ 0.592397] OF: Bad cell count for /spi@1100d000/flash@0/partitions
Mon Oct 9 21:45:37 2023 kern.err kernel: [ 0.598685] OF: Bad cell count for /spi@1100d000/flash@0/partitions
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.605212] Creating 4 MTD partitions on "spi2.0":
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.609998] 0x000000000000-0x000000080000 : "bl2"
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.615740] 0x000000080000-0x0000001c0000 : "fip"
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.622408] 0x0000001c0000-0x0000002c0000 : "factory"
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 0.629007] 0x000000300000-0x000008000000 : "ubi"
Mon Oct 9 21:45:37 2023 kern.err kernel: [ 0.892781] mtk_soc_eth 1b100000.ethernet: generated random MAC address d2:22:b9:50:86:cb
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.903219] mtk_soc_eth 1b100000.ethernet eth0: mediatek frame engine at 0xffffffc0093c0000, irq 141
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.913132] i2c_dev: i2c /dev entries driver
Mon Oct 9 21:45:37 2023 kern.err kernel: [ 0.918675] mtk-wdt 10212000.watchdog: IRQ index 0 not found
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.924534] mtk-wdt 10212000.watchdog: Watchdog enabled (timeout=31 sec, nowayout=0)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.934609] NET: Registered PF_INET6 protocol family
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.940404] Segment Routing with IPv6
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.944240] In-situ OAM (IOAM) with IPv6
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.948200] NET: Registered PF_PACKET protocol family
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.953290] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.966468] 8021q: 802.1Q VLAN Support v1.8
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.971920] pstore: Using crash dump compression: deflate
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 0.988369] mtk-pcie 1a143000.pcie: host bridge /pcie@1a143000 ranges:
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 0.994961] mtk-pcie 1a143000.pcie: Parsing ranges property...
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.000801] mtk-pcie 1a143000.pcie: MEM 0x0020000000..0x0027ffffff -> 0x0020000000
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.147815] mtk-pcie 1a143000.pcie: PCI host bridge to bus 0000:00
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.154026] pci_bus 0000:00: root bus resource [bus 00-ff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.159512] pci_bus 0000:00: root bus resource [mem 0x20000000-0x27ffffff]
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.166398] pci_bus 0000:00: scanning bus
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.170613] pci 0000:00:00.0: [14c3:3258] type 01 class 0x060400
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.176806] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x1ffffffff 64bit pref]
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.186770] pci_bus 0000:00: fixups for bus
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.190965] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 0
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.197684] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.205764] pci 0000:00:00.0: scanning [bus 00-00] behind bridge, pass 1
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.212895] pci_bus 0000:01: scanning bus
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.217119] pci 0000:01:00.0: [14c3:7915] type 00 class 0x000280
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.223314] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.230642] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.237975] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.245948] pci 0000:01:00.0: supports D1 D2
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.250213] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.256859] pci 0000:01:00.0: PME# disabled
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.261360] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.304743] pci_bus 0000:01: fixups for bus
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.308953] pci_bus 0000:01: bus scan returning with max=01
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.314564] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.321203] pci_bus 0000:00: bus scan returning with max=01
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.326799] pci 0000:00:00.0: BAR 0: no space for [mem size 0x200000000 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.334454] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x200000000 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.342467] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.349252] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.357080] pci 0000:01:00.0: BAR 2: assigned [mem 0x20100000-0x20103fff 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.364908] pci 0000:01:00.0: BAR 4: assigned [mem 0x20104000-0x20104fff 64bit pref]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.372734] pci 0000:00:00.0: PCI bridge to [bus 01]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.377696] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff]
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.384628] pcieport 0000:00:00.0: assign IRQ: got 146
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.389773] pcieport 0000:00:00.0: enabling device (0000 -> 0002)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.395886] pcieport 0000:00:00.0: enabling bus mastering
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.401321] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44d6d0c0
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.408727] pcieport 0000:00:00.0: PME: Signaling with IRQ 146
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.414667] pcieport 0000:00:00.0: saving config space at offset 0x0 (reading 0x325814c3)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.422862] pcieport 0000:00:00.0: saving config space at offset 0x4 (reading 0x100006)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.430862] pcieport 0000:00:00.0: saving config space at offset 0x8 (reading 0x6040000)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.438950] pcieport 0000:00:00.0: saving config space at offset 0xc (reading 0x10000)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.446864] pcieport 0000:00:00.0: saving config space at offset 0x10 (reading 0xc)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.454520] pcieport 0000:00:00.0: saving config space at offset 0x14 (reading 0x0)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.462174] pcieport 0000:00:00.0: saving config space at offset 0x18 (reading 0x40010100)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.470430] pcieport 0000:00:00.0: saving config space at offset 0x1c (reading 0x4200000)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.478605] pcieport 0000:00:00.0: saving config space at offset 0x20 (reading 0x20102000)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.486869] pcieport 0000:00:00.0: saving config space at offset 0x24 (reading 0x0)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.494522] pcieport 0000:00:00.0: saving config space at offset 0x28 (reading 0x0)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.502175] pcieport 0000:00:00.0: saving config space at offset 0x2c (reading 0x0)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.509824] pcieport 0000:00:00.0: saving config space at offset 0x30 (reading 0x0)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.517476] pcieport 0000:00:00.0: saving config space at offset 0x34 (reading 0x50)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.525215] pcieport 0000:00:00.0: saving config space at offset 0x38 (reading 0x0)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.532869] pcieport 0000:00:00.0: saving config space at offset 0x3c (reading 0x20192)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.541425] mtk-pcie 1a145000.pcie: host bridge /pcie@1a145000 ranges:
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.547979] mtk-pcie 1a145000.pcie: Parsing ranges property...
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.553819] mtk-pcie 1a145000.pcie: MEM 0x0028000000..0x002fffffff -> 0x0028000000
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.781465] mtk-pcie 1a145000.pcie: Port1 link down
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.786546] mtk-pcie 1a145000.pcie: PCI host bridge to bus 0001:00
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.792754] pci_bus 0001:00: root bus resource [bus 00-ff]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.798242] pci_bus 0001:00: root bus resource [mem 0x28000000-0x2fffffff]
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.805124] pci_bus 0001:00: scanning bus
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.810844] pci_bus 0001:00: fixups for bus
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 1.815034] pci_bus 0001:00: bus scan returning with max=00
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.821208] mtk_hsdma 1b007000.dma-controller: MediaTek HSDMA driver registered
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.871778] mt7530-mdio mdio-bus:00: configuring for fixed/2500base-x link mode
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.881908] mt7530-mdio mdio-bus:00: Link is Up - 2.5Gbps/Full - flow control rx/tx
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.890102] mt7530-mdio mdio-bus:00 lan1 (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7531 PHY] (irq=147)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.911096] mt7530-mdio mdio-bus:00 lan2 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7531 PHY] (irq=148)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.931452] mt7530-mdio mdio-bus:00 lan3 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7531 PHY] (irq=149)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.951785] mt7530-mdio mdio-bus:00 lan4 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7531 PHY] (irq=150)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.972314] mt7530-mdio mdio-bus:00 wan (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7531 PHY] (irq=151)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 1.983615] DSA: tree 0 setup
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 1.987503] UBI: auto-attach mtd3
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 1.990833] ubi0: default fastmap pool size: 50
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 1.995472] ubi0: default fastmap WL pool size: 25
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.000255] ubi0: attaching mtd3
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.302363] ubi0: scanning is finished
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.311900] ubi0: attached mtd3 (name "ubi", size 125 MiB)
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.317404] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.324301] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.331087] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.338047] ubi0: good PEBs: 1000, bad PEBs: 0, corrupted PEBs: 0
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.344145] ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.351360] ubi0: max/mean erase counter: 7/4, WL threshold: 4096, image sequence number: 1503897896
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.360495] ubi0: available PEBs: 0, total reserved PEBs: 1000, PEBs reserved for bad PEB handling: 20
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 2.369812] ubi0: background thread "ubi_bgt0d" started, PID 517
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.371443] FIT: Selected configuration: "config-1" (OpenWrt linksys_e8450-ubi)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.383143] FIT: kernel sub-image 0x00001000..0x004e68d7 "kernel-1" (ARM64 OpenWrt Linux-5.15.134)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.393070] FIT: flat_dt sub-image 0x004e7000..0x004ee712 "fdt-1" (ARM64 OpenWrt linksys_e8450-ubi device tree blob)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.404467] FIT: filesystem sub-image 0x004ef000..0x00967fff "rootfs-1" (ARM64 OpenWrt linksys_e8450-ubi rootfs)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.415252] FIT: selecting configured loadable "rootfs-1" to be root filesystem
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 2.422555] ubiblock0_5: p1(rootfs-1)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 2.422754] block ubiblock0_5: created from ubi0:5(fit)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 2.435162] VFS: Mounted root (squashfs filesystem) readonly on device 259:0.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 2.442543] Freeing unused kernel memory: 448K
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 2.501535] Run /sbin/init as init process
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.505640] with arguments:
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.508604] /sbin/init
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.511308] with environment:
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.514478] HOME=/
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 2.516836] TERM=linux
Mon Oct 9 21:45:37 2023 user.info kernel: [ 2.692688] init: Console is alive
Mon Oct 9 21:45:37 2023 user.info kernel: [ 2.696241] init: - watchdog -
Mon Oct 9 21:45:37 2023 user.info kernel: [ 3.076198] kmodloader: loading kernel modules from /etc/modules-boot.d/*
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.101301] usbcore: registered new interface driver usbfs
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.106881] usbcore: registered new interface driver hub
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.112249] usbcore: registered new device driver usb
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.122716] xhci-mtk 1a0c0000.usb: xHCI Host Controller
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.127982] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 1
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.137086] xhci-mtk 1a0c0000.usb: hcc params 0x01403198 hci version 0x96 quirks 0x0000000000210010
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.146291] xhci-mtk 1a0c0000.usb: irq 135, io mem 0x1a0c0000
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.152168] xhci-mtk 1a0c0000.usb: xHCI Host Controller
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.157398] xhci-mtk 1a0c0000.usb: new USB bus registered, assigned bus number 2
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.164812] xhci-mtk 1a0c0000.usb: Host supports USB 3.0 SuperSpeed
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.171563] hub 1-0:1.0: USB hub found
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.175359] hub 1-0:1.0: 2 ports detected
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.179742] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.188262] hub 2-0:1.0: USB hub found
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.192106] hub 2-0:1.0: 1 port detected
Mon Oct 9 21:45:37 2023 user.info kernel: [ 3.200130] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
Mon Oct 9 21:45:37 2023 user.info kernel: [ 3.209195] init: - preinit -
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.494004] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.502615] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 3.512313] mt7530-mdio mdio-bus:00 lan1: configuring for phy/gmii link mode
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 5.163293] mt7530-mdio mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 5.171284] IPv6: ADDRCONF(NETDEV_CHANGE): lan1: link becomes ready
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.613981] UBIFS (ubi0:7): default file-system created
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.619524] UBIFS (ubi0:7): Mounting in unauthenticated mode
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.625362] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 632
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.654497] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "rootfs_data"
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.662374] UBIFS (ubi0:7): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.672309] UBIFS (ubi0:7): FS size: 94724096 bytes (90 MiB, 746 LEBs), max 757 LEBs, journal size 4698112 bytes (4 MiB, 37 LEBs)
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.683967] UBIFS (ubi0:7): reserved for root: 4474052 bytes (4369 KiB)
Mon Oct 9 21:45:37 2023 kern.notice kernel: [ 5.690577] UBIFS (ubi0:7): media format: w5/r0 (latest is w5/r0), UUID 71996F7B-B430-41EF-B16F-21F56C5DB42C, small LPT model
Mon Oct 9 21:45:37 2023 user.info kernel: [ 5.703283] mount_root: overlay filesystem has not been fully initialized yet
Mon Oct 9 21:45:37 2023 user.info kernel: [ 5.710637] mount_root: switching to ubifs overlay
Mon Oct 9 21:45:37 2023 kern.warn kernel: [ 5.717610] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
Mon Oct 9 21:45:37 2023 user.debug kernel: [ 5.729166] urandom-seed: Seed file not found (/etc/urandom.seed)
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 5.774458] mt7530-mdio mdio-bus:00 lan1: Link is Down
Mon Oct 9 21:45:37 2023 user.info kernel: [ 5.783508] procd: - early -
Mon Oct 9 21:45:37 2023 user.info kernel: [ 5.786479] procd: - watchdog -
Mon Oct 9 21:45:37 2023 user.info kernel: [ 6.328277] procd: - watchdog -
Mon Oct 9 21:45:37 2023 user.info kernel: [ 6.332024] procd: - ubus -
Mon Oct 9 21:45:37 2023 user.info kernel: [ 6.388727] procd: - init -
Mon Oct 9 21:45:37 2023 user.info kernel: [ 6.647959] kmodloader: loading kernel modules from /etc/modules.d/*
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 6.657929] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 6.665488] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 6.741532] mt7622-wmac 18000000.wmac: Invalid MAC address, using random address de:9c:f0:18:e9:76
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 6.752357] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 6.765368] mt7915e 0000:01:00.0: assign IRQ: got 146
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 6.770485] mt7915e 0000:01:00.0: enabling device (0000 -> 0002)
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 6.776654] mt7915e 0000:01:00.0: enabling bus mastering
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 6.831587] mt7622-wmac 18000000.wmac: HW/SW Version: 0x8a108a10, Build Time: 20190801210006a
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 6.831587]
Mon Oct 9 21:45:37 2023 user.info kernel: [ 6.856304] urngd: v1.0.2 started.
Mon Oct 9 21:45:37 2023 kern.debug kernel: [ 6.908334] mtk-pcie 1a143000.pcie: msi#0 address_hi 0x0 address_lo 0x44d6d0c0
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 6.969199] mt7622-wmac 18000000.wmac: N9 Firmware Version: _reserved_, Build Time: 20220630094834
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 7.005004] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20220929104113a
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 7.005004]
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 7.201929] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20220929104145
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 7.254751] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20220929104205
Mon Oct 9 21:45:37 2023 kern.warn kernel: [ 7.371350] mt7915e 0000:01:00.0: eeprom load fail, use default bin
Mon Oct 9 21:45:37 2023 kern.warn kernel: [ 7.377846] mt7915e 0000:01:00.0: Direct firmware load for mediatek/mt7915_eeprom.bin failed with error -2
Mon Oct 9 21:45:37 2023 kern.warn kernel: [ 7.387537] mt7915e 0000:01:00.0: Falling back to sysfs fallback for: mediatek/mt7915_eeprom.bin
Mon Oct 9 21:45:37 2023 kern.warn kernel: [ 7.403893] mt7915e: probe of 0000:01:00.0 failed with error -12
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 7.433512] PPP generic driver version 2.4.2
Mon Oct 9 21:45:37 2023 kern.info kernel: [ 7.439099] NET: Registered PF_PPPOX protocol family
Mon Oct 9 21:45:37 2023 user.info kernel: [ 7.447938] kmodloader: done loading kernel modules from /etc/modules.d/*
Mon Oct 9 21:45:38 2023 user.notice dnsmasq: DNS rebinding protection is active, will discard upstream RFC1918 responses!
Mon Oct 9 21:45:38 2023 user.notice dnsmasq: Allowing 127.0.0.0/8 responses
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: started, version 2.89 cachesize 1000
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: DNS service limited to local subnets
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: using only locally-known addresses for test
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: using only locally-known addresses for local
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Mon Oct 9 21:45:38 2023 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Mon Oct 9 21:45:38 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 0 names
Mon Oct 9 21:45:43 2023 authpriv.info dropbear[1556]: Not backgrounding
Mon Oct 9 21:45:44 2023 daemon.notice wpa_supplicant[1666]: Successfully initialized wpa_supplicant
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: bonding
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: 8021ad
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: 8021q
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: macvlan
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: veth
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: bridge
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: Network device
Mon Oct 9 21:45:44 2023 user.notice : Added device handler type: tunnel
Mon Oct 9 21:45:44 2023 daemon.notice procd: /etc/rc.d/S25packet_steering: uci: Entry not found
Mon Oct 9 21:45:44 2023 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/network
Mon Oct 9 21:45:44 2023 user.notice ucitrack: Setting up /etc/config/network reload dependency on /etc/config/wireless
Mon Oct 9 21:45:44 2023 user.notice ucitrack: Setting up /etc/config/luci-splash reload dependency on /etc/config/firewall
Mon Oct 9 21:45:44 2023 user.notice ucitrack: Setting up /etc/config/qos reload dependency on /etc/config/firewall
Mon Oct 9 21:45:44 2023 user.notice ucitrack: Setting up /etc/config/miniupnpd reload dependency on /etc/config/firewall
Mon Oct 9 21:45:45 2023 user.notice ucitrack: Setting up /etc/config/odhcpd reload dependency on /etc/config/dhcp
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.594879] mtk_soc_eth 1b100000.ethernet eth0: Link is Down
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.607626] mtk_soc_eth 1b100000.ethernet eth0: configuring for fixed/2500base-x link mode
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.617986] mtk_soc_eth 1b100000.ethernet eth0: Link is Up - 2.5Gbps/Full - flow control rx/tx
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.623010] mt7530-mdio mdio-bus:00 lan1: configuring for phy/gmii link mode
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.635236] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.641857] br-lan: port 1(lan1) entered blocking state
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.647098] br-lan: port 1(lan1) entered disabled state
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.660417] device lan1 entered promiscuous mode
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.665120] device eth0 entered promiscuous mode
Mon Oct 9 21:45:45 2023 user.notice ucitrack: Setting up non-init /etc/config/fstab reload handler: /sbin/block mount
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'lan' is enabled
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'lan' is setting up now
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'lan' is now up
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.684896] mt7530-mdio mdio-bus:00 lan2: configuring for phy/gmii link mode
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.697070] br-lan: port 2(lan2) entered blocking state
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.702397] br-lan: port 2(lan2) entered disabled state
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.710076] device lan2 entered promiscuous mode
Mon Oct 9 21:45:45 2023 user.notice ucitrack: Setting up /etc/config/system reload trigger for non-procd /etc/init.d/led
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.723599] mt7530-mdio mdio-bus:00 lan3: configuring for phy/gmii link mode
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.736446] br-lan: port 3(lan3) entered blocking state
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.741708] br-lan: port 3(lan3) entered disabled state
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.749939] device lan3 entered promiscuous mode
Mon Oct 9 21:45:45 2023 user.notice ucitrack: Setting up /etc/config/luci_statistics reload dependency on /etc/config/system
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.769277] mt7530-mdio mdio-bus:00 lan4: configuring for phy/gmii link mode
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.780159] br-lan: port 4(lan4) entered blocking state
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.785463] br-lan: port 4(lan4) entered disabled state
Mon Oct 9 21:45:45 2023 user.notice ucitrack: Setting up /etc/config/dhcp reload dependency on /etc/config/system
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.793499] device lan4 entered promiscuous mode
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'loopback' is enabled
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'loopback' is setting up now
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'loopback' is now up
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'wan' is enabled
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'wan6' is enabled
Mon Oct 9 21:45:45 2023 kern.info kernel: [ 16.809003] mt7530-mdio mdio-bus:00 wan: configuring for phy/gmii link mode
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Network device 'eth0' link is up
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Network device 'lo' link is up
Mon Oct 9 21:45:45 2023 daemon.notice netifd: Interface 'loopback' has link connectivity
Mon Oct 9 21:45:45 2023 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
Mon Oct 9 21:45:45 2023 daemon.notice procd: /etc/rc.d/S96led: setting up led WAN
Mon Oct 9 21:45:45 2023 daemon.info procd: - init complete -
Mon Oct 9 21:45:45 2023 daemon.info urandom_seed[2431]: Seed saved (/etc/urandom.seed)
Mon Oct 9 21:45:48 2023 kern.info kernel: [ 20.313865] mt7530-mdio mdio-bus:00 lan1: Link is Up - 1Gbps/Full - flow control rx/tx
Mon Oct 9 21:45:48 2023 kern.info kernel: [ 20.321885] br-lan: port 1(lan1) entered blocking state
Mon Oct 9 21:45:48 2023 kern.info kernel: [ 20.327122] br-lan: port 1(lan1) entered forwarding state
Mon Oct 9 21:45:48 2023 daemon.notice netifd: Network device 'lan1' link is up
Mon Oct 9 21:45:48 2023 kern.info kernel: [ 20.334777] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
Mon Oct 9 21:45:48 2023 daemon.notice netifd: bridge 'br-lan' link is up
Mon Oct 9 21:45:48 2023 daemon.notice netifd: Interface 'lan' has link connectivity
Mon Oct 9 21:45:49 2023 kern.info kernel: [ 20.668628] mt7530-mdio mdio-bus:00 lan3: Link is Up - 1Gbps/Full - flow control rx/tx
Mon Oct 9 21:45:49 2023 kern.info kernel: [ 20.676655] br-lan: port 3(lan3) entered blocking state
Mon Oct 9 21:45:49 2023 kern.info kernel: [ 20.681920] br-lan: port 3(lan3) entered forwarding state
Mon Oct 9 21:45:49 2023 daemon.notice netifd: Network device 'lan3' link is up
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: exiting on receipt of SIGTERM
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: started, version 2.89 cachesize 1000
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: DNS service limited to local subnets
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: compile time options: IPv6 GNU-getopt no-DBus UBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-nftset no-auth no-cryptohash no-DNSSEC no-ID loop-detect inotify dumpfile
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: UBus support enabled: connected to system bus
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq-dhcp[1]: DHCP, IP range 192.168.1.100 -- 192.168.1.249, lease time 12h
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: using only locally-known addresses for test
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: using only locally-known addresses for onion
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: using only locally-known addresses for localhost
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: using only locally-known addresses for local
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: using only locally-known addresses for invalid
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: using only locally-known addresses for bind
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: using only locally-known addresses for lan
Mon Oct 9 21:45:49 2023 daemon.warn dnsmasq[1]: no servers found in /tmp/resolv.conf.d/resolv.conf.auto, will retry
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Mon Oct 9 21:45:49 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Mon Oct 9 21:45:50 2023 daemon.err odhcpd[1833]: Failed to send to fe80::df56:7ff:1dc1:a342%lan@br-lan (Address not available)
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 0 names
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 0 names
Mon Oct 9 21:45:50 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Mon Oct 9 21:45:51 2023 daemon.warn odhcpd[1833]: No default route present, overriding ra_lifetime!
Mon Oct 9 21:45:52 2023 daemon.info dnsmasq[1]: read /etc/hosts - 12 names
Mon Oct 9 21:45:52 2023 daemon.info dnsmasq[1]: read /tmp/hosts/dhcp.cfg01411c - 4 names
Mon Oct 9 21:45:52 2023 daemon.info dnsmasq[1]: read /tmp/hosts/odhcpd - 2 names
Mon Oct 9 21:45:52 2023 daemon.info dnsmasq-dhcp[1]: read /etc/ethers - 0 addresses
Mon Oct 9 21:46:04 2023 daemon.err uhttpd[1018]: [info] luci: accepted login on / for root from 192.168.1.254
Mon Oct 9 21:46:05 2023 daemon.warn odhcpd[1833]: No default route present, overriding ra_lifetime!
Mon Oct 9 21:46:21 2023 daemon.warn odhcpd[1833]: No default route present, overriding ra_lifetime!
Mon Oct 9 21:46:42 2023 authpriv.info dropbear[2982]: Child connection from 192.168.1.254:62903
Mon Oct 9 21:46:49 2023 authpriv.notice dropbear[2982]: Auth succeeded with blank password for 'root' from 192.168.1.254:62903
root@OpenWrt:~#As others have suggested in past posts, I have also checked that the kmod-mt7915-firmware is installed. I've also tried force-reinstalling it to no avail.
Where do I go from here? I am still newish to OpenWRT, and did not expect this device to be so troublesome.
wit-know
commented
9 months ago Also, here is the hexdump info:
root@OpenWrt:~# hexdump -C /dev/mtdblock2
00000000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
00000010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
00000020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
00020000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
00020010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
00020020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00020030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
00020040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
00040000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
00040010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
00040020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00040030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
00040040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
00060000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
00060010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
00060020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00060030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
00060040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
00080000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
00080010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
00080020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00080030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
00080040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
000a0000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
000a0010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
000a0020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000a0030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
000a0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
000c0000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
000c0010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
000c0020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000c0030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
000c0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
000e0000 55 42 49 23 01 00 00 00 00 00 00 00 00 00 00 00 |UBI#............|
000e0010 00 00 08 00 00 00 10 00 59 a3 a9 28 00 00 00 00 |........Y..(....|
000e0020 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
000e0030 00 00 00 00 00 00 00 00 00 00 00 00 8f 90 c1 70 |...............p|
000e0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
*
00100000
root@OpenWrt:~#@wit-know your issue can be seen in your kernel log:
[ 7.005004] mt7915e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20220929104113a
[ 7.005004]
[ 7.201929] mt7915e 0000:01:00.0: WM Firmware Version: ____000000, Build Time: 20220929104145
[ 7.254751] mt7915e 0000:01:00.0: WA Firmware Version: DEV_000000, Build Time: 20220929104205
[ 7.371350] mt7915e 0000:01:00.0: eeprom load fail, use default bin
[ 7.377846] mt7915e 0000:01:00.0: Direct firmware load for mediatek/mt7915_eeprom.bin failed with error -2
[ 7.387537] mt7915e 0000:01:00.0: Falling back to sysfs fallback for: mediatek/mt7915_eeprom.bin
[ 7.403893] mt7915e: probe of 0000:01:00.0 failed with error -12Just searching for mt7915e on GitHub shows lots of people having issues with this driver. I don't think this is necessarily related to this installer repository. Here's someone with your exact error message: openwrt/openwrt#14207
dangowrt
commented
8 months ago @wit-know What you are seeing is the (expected) result of having used the v1.1.x installer and then trying to use an older OpenWrt release. That can't work. And it's not related to the original issue, but actually another issue.
Where do I go from here? I am still newish to OpenWRT, and did not expect this device to be so troublesome.
After using the v1.1.x installer there is no going back, or at least it is not trivial. You cannot use 23.05.x then, unless you first completely restore the device to factory state and then run the pre-v1.1.x installer.
If you want to do that, you will need the backup files from the boot_backup UBI volume and write them to the appropriate MTD partitions. If you are not sure what you are doing, probably the best for now is to just use snapshot images until there will be the next stable release.
dangowrt
commented
8 months ago @wallrik Neither kmod-mt7915e nor missing firmware files are the problem here. The problem is that OP has moved the factory data into a UBI volume (instead of a raw flash partition) and is trying to run an OpenWrt which still expects it in a raw MTD partition. Simple as that.
wit-know
commented
8 months ago @wit-know What you are seeing is the (expected) result of having used the v1.1.x installer and then trying to use an older OpenWrt release. That can't work. And it's not related to the original issue, but actually another issue.
Where do I go from here? I am still newish to OpenWRT, and did not expect this device to be so troublesome.
After using the v1.1.x installer there is no going back, or at least it is not trivial. You cannot use 23.05.x then, unless you first completely restore the device to factory state and then run the pre-v1.1.x installer.
If you want to do that, you will need the backup files from the
boot_backupUBI volume and write them to the appropriate MTD partitions. If you are not sure what you are doing, probably the best for now is to just use snapshot images until there will be the next stable release.
Thank you, Dan, for all your help. I was able to revert to revert back to the Linksys firmware 1.0.01.101415, and then proceeded to upload the 23.05.0 installer. However, while flashing the the 23.05.0 sysupgrade, the unit bricked! I don't know how that happened, but now I have a USB UART adapter on the way and then will proceed from there.
As a side note, if I can recall correctly, after I accidentally installed the v1.1.1 installer (my fault), I was still never able to install the v1.1.1 sysupgrade successfully. That is how I ended up flashing the 23.05.0 sysupgrade instead. Regardless, I was a bit green in rushing about while installing those releases, and probably did not fully read your instructions on Github. Your detailed instructions are actually written quite clearly.
dangowrt
commented
8 months ago @wit-know Strange, but hard to tell what happened before connecting the serial. Feel free to reach out should you need more assistance.
zow2023
commented
6 months ago Can you tell me the details of the process of restoring the factory firmware from the latest installer？ @dangowrt
kratanat
commented
4 months ago I also have the same issue where I ran the 1.1.2, then install the latest UBI SNAPSHOT from the OpenWRT website. I'm using Linksys e8450. After comparing configuration with Belkin 3200. I was able to find out what causing the radios to show generic. My kernel log does not have any error with firmware. Firmware mt7622 and 7915e were loaded without issue.
When I run command "iw phy" on the snapshot, and the wifi was listed under "phy0" and "phy1", while under previous stable release, iw command returned "wl0" and "wl1"
So I edited "/etc/config/wireless"
under
wifi-device 'radio0'
option phy 'wl0' changed to option phy 'phy0'
under radio1 section, I change from 'wl1' to 'phy1'
After refresh wifi page on luci, I am able to see the correct name
However, it seems like there is an automatic generation of wireless config that it added a wl0 and wl1 entries back under radio2 and radio 3, but it did work. If somebody can find out how the autogenerate work, this issue can be solve. It is either the "iw" command issue or the template incompatibility with the iw.
Additionally, it seems that the automatic generation has something to do with /etc/board.json So I change the name of the section "wl0" and "wl1" to "phy0" and "phy1" respectively, then I removed section of wifi-device 'radio2' and wifi-device 'radio3' out from /etc/config/wireless
After rebooting the router, it seems that wifi page has no new generated generic radio anymore. Conclusion, it definitely has something to do with "phy" name change that caused the pre configuration to fail. I do not know what command used to generate config but I suspected "wifi config" command according to this link or iw command.
john-clark
commented
3 days ago What is the solution for the generic 5ghz wifi not loading wth the 23.05.05 and installer 1.1.1?
My router also will not keep its dhcp lan and requests a new ip every reboot with the same mac address.
I don't remember when 5G disappeared or what update triggered it, probably about 2 year ago. But now a new device is on the network and want this frequency.
I saw the advices at #114 and I did this steps (the is last called "mediatek-mt7622-linksys_e8450-ubi-squashfs-sysupgrade.itb" located at https://github.com/dangowrt/owrt-ubi-installer/releases/ ):
Wait to restart and login on luci, gone to WiFi section and obtain the same result:
Can I do something to fix it or the 5G is broken forever?