nsk
commented
7 months ago resolved with : echo 'dtoverlay=pi3-miniuart-bt' | sudo tee -a /boot/config.txt
this information should be highlighted more
Closed nsk closed 7 months ago
nsk
commented
7 months ago resolved with : echo 'dtoverlay=pi3-miniuart-bt' | sudo tee -a /boot/config.txt
this information should be highlighted more
Hi ,
Impossible to connect the raspbee II, it is not recognized by the docker image, nor by the new version of debian previously it detected it in ttyS0, now in ttyAMA1 or tty1 and not ttyAMA0 moreover the docker image cannot do this connected to the network, do I need to update the firmware?? is it possible to connect the raspbee II via a USB tool -->> Serial to flash??
thank you for any help that could be given
PRETTY_NAME="Debian GNU/Linux 12 (bookworm)" NAME="Debian GNU/Linux"
dmesg | grep serial [ 1.670104] uart-pl011 fe201000.serial: there is not valid maps for state default [ 1.671077] uart-pl011 fe201000.serial: cts_event_workaround enabled [ 1.671255] fe201000.serial: ttyAMA1 at MMIO 0xfe201000 (irq = 36, base_baud = 0) is a PL011 rev2 [ 1.671536] serial serial0: tty port ttyAMA1 registered [ 1.679910] bcm2835-aux-uart fe215040.serial: there is not valid maps for state default [ 1.681011] fe215040.serial: ttyS0 at MMIO 0xfe215040 (irq = 37, base_baud = 62500000) is a 16550 [ 8.790017] hci_uart_bcm serial0-0: supply vbat not found, using dummy regulator [ 8.790310] hci_uart_bcm serial0-0: supply vddio not found, using dummy regulator [ 8.909098] uart-pl011 fe201000.serial: no DMA platform data
cat /sys/devices/virtual/tty/console/active tty1
gpioinfo gpiochip0 - 58 lines: line 0: "ID_SDA" unused input active-high line 1: "ID_SCL" unused input active-high line 2: "SDA1" unused input active-high line 3: "SCL1" unused input active-high line 4: "GPIO_GCLK" unused input active-high line 5: "GPIO5" unused input active-high line 6: "GPIO6" unused input active-high line 7: "SPI_CE1_N" "spi0 CS1" output active-low [used] line 8: "SPI_CE0_N" "spi0 CS0" output active-low [used] line 9: "SPI_MISO" unused input active-high line 10: "SPI_MOSI" unused input active-high line 11: "SPI_SCLK" unused input active-high line 12: "GPIO12" unused input active-high line 13: "GPIO13" unused input active-high line 14: "TXD1" unused input active-high line 15: "RXD1" unused input active-high line 16: "GPIO16" unused input active-high line 17: "GPIO17" unused input active-high line 18: "GPIO18" unused input active-high line 19: "GPIO19" unused input active-high line 20: "GPIO20" unused input active-high line 21: "GPIO21" unused input active-high line 22: "GPIO22" unused input active-high line 23: "GPIO23" unused input active-high line 24: "GPIO24" unused input active-high line 25: "GPIO25" unused input active-high line 26: "GPIO26" unused input active-high line 27: "GPIO27" unused input active-high line 28: "RGMII_MDIO" unused input active-high line 29: "RGMIO_MDC" unused input active-high line 30: "CTS0" unused input active-high line 31: "RTS0" unused input active-high line 32: "TXD0" unused input active-high line 33: "RXD0" unused input active-high line 34: "SD1_CLK" unused input active-high line 35: "SD1_CMD" unused input active-high line 36: "SD1_DATA0" unused input active-high line 37: "SD1_DATA1" unused input active-high line 38: "SD1_DATA2" unused input active-high line 39: "SD1_DATA3" unused input active-high line 40: "PWM0_MISO" unused input active-high line 41: "PWM1_MOSI" unused input active-high line 42: "STATUS_LED_G_CLK" "ACT" output active-high [used] line 43: "SPIFLASH_CE_N" unused input active-high line 44: "SDA0" unused input active-high line 45: "SCL0" unused input active-high line 46: "RGMII_RXCLK" unused input active-high line 47: "RGMII_RXCTL" unused input active-high line 48: "RGMII_RXD0" unused input active-high line 49: "RGMII_RXD1" unused input active-high line 50: "RGMII_RXD2" unused input active-high line 51: "RGMII_RXD3" unused input active-high line 52: "RGMII_TXCLK" unused input active-high line 53: "RGMII_TXCTL" unused input active-high line 54: "RGMII_TXD0" unused input active-high line 55: "RGMII_TXD1" unused input active-high line 56: "RGMII_TXD2" unused input active-high line 57: "RGMII_TXD3" unused input active-high gpiochip1 - 8 lines: line 0: "BT_ON" "shutdown" output active-high [used] line 1: "WL_ON" unused output active-high line 2: "PWR_LED_OFF" "PWR" output active-low [used] line 3: "GLOBAL_RESET" unused output active-high line 4: "VDD_SD_IO_SEL" "vdd-sd-io" output active-high [used] line 5: "CAM_GPIO" "cam1_regulator" output active-high [used] line 6: "SD_PWR_ON" "sd_vcc_reg" output active-high [used] line 7: "SD_OC_N" unused input active-high pi@Chester:~ $ ps -l