search

derekperrin / rt-n56u

Automatically exported from code.google.com/p/rt-n56u
0 stars 0 forks source link

CY-SW1100 Build Target "invalid image file" #761

Open GoogleCodeExporter opened 9 years ago

GoogleCodeExporter commented 9 years ago 
I have a samsung CY-SWR1100 router - upon doing a build of your firmware to the 
SWR1100 target I receive a TRX file.

When I upload the TRX file to the router via the web interface I get the error 
"Invalid Image File".

Any idea what the cause is?

Original issue reported on code.google.com by harri...@isabarwon.com on 17 Mar 2013 at 11:44

GoogleCodeExporter commented 9 years ago 
CY-SWR1100 original firmware used different image header. 

First flash firmware possible only via emergency utility (TFTP) or via UART 
console. Any next custom firmware updates will be available via WebGUI.

Original comment by andy.pad...@gmail.com on 18 Mar 2013 at 6:47

GoogleCodeExporter commented 9 years ago 
Is there a particular process to getting the SWR1100 to flash from TFTP?

I've used the Linksys TFTP2 program and offered it a TRX file but it does not 
flash. Suggestions?

Original comment by harri...@isabarwon.com on 19 Mar 2013 at 12:12

GoogleCodeExporter commented 9 years ago 
Try to use ASUS Firmware Restoration Utility (TFTP client for Ralink uboot) 
from N56U utilites.

Original comment by andy.pad...@gmail.com on 21 Mar 2013 at 10:50

GoogleCodeExporter commented 9 years ago 
What IP address should I be setting my NIC to, and which port should I plug the 
LAN cable into?

192.168.0.10 and 192.168.1.10 both don't work.

Original comment by harri...@isabarwon.com on 22 Mar 2013 at 2:54

GoogleCodeExporter commented 9 years ago 
Turn off SWR-1100. Press and hold reset button and turn on router. Wait 5 
second and relase reset button. Router now "Emergency Mode" and IP adress 
10.10.10.123.

Connect router to network cable. Close Firewall & Anti Virus program in your 
PC. Turn off wireless network adapter.  Change your Ethernet Card settings ; ip 
10.10.10.224 Subnet Mask : 255.255.255.0 Default Gateway : Empty

In your internet browser, router now reachable via 10.10.10.123 "Emergency Mode"

It's what I know. I can't find any emergency rom and tftp updater for SWR-1100.

Can you give me information about your work?

Original comment by euphori...@gmail.com on 31 Mar 2013 at 6:28

GoogleCodeExporter commented 9 years ago 
[deleted comment]
GoogleCodeExporter commented 9 years ago 
Thanks for the reply, that's exactly the info I needed.

I have no work as yet, I was merely wanting to install this firmware on my 
device to improve it's wireless capabilities and provide feedback, and 
potentially contribute some basic bugfixes.

Is the firmware in a working condition on the device as yet?

I have two of these routers.

Original comment by harri...@isabarwon.com on 4 Apr 2013 at 1:46

GoogleCodeExporter commented 9 years ago 
Interestingly enough I am unable to even reach the router via the above 
settings... the router remains unreachable. Is there a specific port number I 
should plug into?

Original comment by harri...@isabarwon.com on 4 Apr 2013 at 1:57

GoogleCodeExporter commented 9 years ago 
Please visit this pages ; 

https://www.box.com/s/2wxyv4cjdgd52m4a1wzd  
https://www.box.com/s/2wxyv4cjdgd52m4a1wzd#/s/2wxyv4cjdgd52m4a1wzd/1/322627961/5
796404238/1

I still can not upload any firmware.

Original comment by euphori...@gmail.com on 6 Apr 2013 at 2:47

GoogleCodeExporter commented 9 years ago 
Same problem here. I tried using the "Emergency Mode" to upload the TRX file 
but it still saying "Invalid Image File"

Original comment by skigel...@gmail.com on 27 Apr 2013 at 1:34

GoogleCodeExporter commented 9 years ago 
On my SWR1100, the emergency mode webserver is 192.168.0.1 probed using the 
serial connection.

Still haven't managed to update the firmware.

Original comment by euan.kir...@gmail.com on 20 Sep 2013 at 11:24

GoogleCodeExporter commented 9 years ago 
Boot logs for normal boot, emergency mode, and entering uboot

U-Boot 1.1.3 (Oct 11 2010 - 14:10:10) (ALPHA)

SVN revision: 432

Target board: WRG-ND10

Board: Ralink APSoC DRAM:  64 MB

Flash: Bank 0, ID:00032228, Size 8388608 (0x00800000)

============================================ 

Ralink UBoot Version: 3.3

-------------------------------------------- 

ASIC 3883_MP (MAC to REALTEK Mode)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Total memory: 64 MBytes

Flash component: NOR Flash

Date:Oct 11 2010  Time:14:10:10

============================================ 

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768 

gpio_init: write 0x0000185f to GPIOMODE(0xb0000060)

 Initializing RTL8367 GbE switch ...

 Setting RTL8367R RGMII Delay time 0x08(TX:01,RX:00)

Please choose the operation: 

   1: Load system code to SDRAM via TFTP. 

   2: Load system code then write to Flash via TFTP. 

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   7: Load Boot Loader code then write to Flash via Serial. 

   9: Load Boot Loader code then write to Flash via TFTP. 

 0 

3: System Boot system code via Flash.

## Booting image at bc050000 ...

We have SEAMA, Image Size = 5877792

Verifying Checksum ...

Uncompressing SEAMA linux.lzma ... OK

## Transferring control to Linux (at address bc05000c) ...

## Giving linux memsize in MB, 64

Starting kernel ...

LINUX started...

 THIS IS ASIC
Linux version 2.6.33.2 (joely@enzo) (gcc version 4.3.3 (GCC) ) #1 Tue Apr 19 
15:07:03 CST 2011

 The CPU feqenuce set to 500 MHz
bootconsole [early0] enabled
CPU revision is: 0001974c (MIPS 74Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)

init started: BusyBox v1.14.1 (2011-04-19 15:07:11 CST)

starting pid 334, tty '': '/etc/init.d/rcS'
[/etc/init.d/S10init.sh]
[/etc/init.d/S15udevd.sh]
[/etc/init.d/S16ipv6.sh]
[/etc/init.d/S19devfs.sh]
[/etc/init.d/S19init.sh]
[/etc/init.d/S20init.sh]
  DEFNODE[/etc/defnodes/S11devdata.xml]
  DEFNODE[/etc/defnodes/S12flashspeed.php]
  DEFNODE[/etc/defnodes/S14setchlist.php]
  DEFNODE[/etc/defnodes/S20device.xml]
  DEFNODE[/etc/defnodes/S22timezone.php]
[/etc/scripts/setdate.sh] 01/01/2000 ...
Sat Jan  1 19:00:03 EST 2000
  DEFNODE[/etc/defnodes/S30device.php]
  DEFNODE[/etc/defnodes/S30device.sh]
  DEFNODE[/etc/defnodes/S30device.xml]
  DEFNODE[/etc/defnodes/S31diagnostic.xml]
  DEFNODE[/etc/defnodes/S31locale.php]
  DEFNODE[/etc/defnodes/S33wifi.php]
  DEFNODE[/etc/defnodes/S40device.xml]
  DEFNODE[/etc/defnodes/S40links.php]
  DEFNODE[/etc/defnodes/S90sessions.php]
  DEFNODE[/etc/defnodes/S90upnpigd.php]
  DEFNODE[/etc/defnodes/S90upnpwfa.php]
debug = 0
 [/etc/init.d/S20interfaces.sh]
[/etc/init.d/S21rdm.sh]
[/etc/init.d/S23udevd.sh]
[/etc/init.d/S45gpiod.sh]
[/etc/init.d/S45rtstad.sh]
Factory reset time : 5 secs
00: WPSLED Blue LED using GPIO #0, output mode.
01: WPS button using GPIO #3, input mode.
02: FRESET button using GPIO #6, input mode.
03: USB Blue LED using GPIO #25, output mode.
[/etc/init.d/rcS] done!
rtstad: not found
 [/etc/init0.d/S21layout.sh]: start ...
 [/etc/init0.d/S40event.sh]: start ...
                                        [/etc/init0.d/S40gpioevent.sh]: start ...
  SEAMA: '/dev/mtdblock/5' is not a seama file !
               [/etc/init0.d/S41autowan.sh]: start ...
  [/etc/init0.d/S41event.sh]: start ...
 [/etc/init0.d/S41inf.sh]: start ...
       [/etc/init0.d/S42pthrough.sh]: start ...
 [/etc/init0.d/S51wlan.sh]: start ...
  [/etc/init0.d/S65ddnsd.sh]: start ...
[/etc/init0.d/S80telnetd.sh]: start ...
bind br0 fail try again
/etc/script/dbsave.sh: can't open
[/etc/init0.d/rcS] done!

Please press Enter to activate this console.          BRIDGE: The device is not 
in the bridge mode.
                                                    [/var/servd/INET.LAN-1_start.sh]: starting LAN-1...
 [/var/servd/INET.LAN-1_start.sh]: starting LAN-1 done !!!
 [/var/servd/INET.LAN-2_start.sh]: starting LAN-2...
 [/var/servd/INET.LAN-2_start.sh]: starting LAN-2 done !!!
 [/var/servd/INET.LAN-3_start.sh]: starting LAN-3...
LAN-3 a is link local interface.
  [/var/servd/INET.LAN-3_start.sh]: starting LAN-3 done !!!
#!/bin/sh
# No inet profile!!
exit 9

[/var/servd/INET.WAN-1_start.sh]: starting WAN-1...
    [/var/servd/INET.WAN-1_start.sh]: starting WAN-1 done !!!
ifsetup: (WAN-2) not active.
[/var/servd/INET.WAN-3_start.sh]: starting WAN-3...
WAN-3 a is link local interface.
  [/var/servd/INET.WAN-3_start.sh]: starting WAN-3 done !!!
ifsetup: (WAN-4) not active.
IPTDMZ: cnt= 1
                                              updatewifistats -s /etc/scripts/upwifistatshlper_A_band.sh  -m RT2800 -i ra0 -x /phyinf:6 -r /runtime/phyinf:4  &
    updatewifistats -s /etc/scripts/upwifistatshlper_G_band.sh  -m RT2800 -i rai0 -x /phyinf:4 -r /runtime/phyinf:5  &
    Reading topology file /var/topology.conf ...
ralink_init: Initiating ralink_wireless_event_init...
ralink_init: Initiating ralink_wireless_event_init...
Using interface ra0 with hwaddr 1c:7e:e5:96:97:78 and ssid 'Brutus and Oscars 
house'
      Using interface rai0 with hwaddr 1c:7e:e5:96:97:7a and ssid 'Brutus and Oscars house'
   LAN-1 Start Traffic Control system ...
LAN-1 Traffic Control is disabled.
httpsetup: (LAN-2) not active.
     httpsetup: (WAN-3) not active.

U-Boot 1.1.3 (Oct 11 2010 - 14:10:10) (ALPHA)

SVN revision: 432

Target board: WRG-ND10

Board: Ralink APSoC DRAM:  64 MB

Flash: Bank 0, ID:00032228, Size 8388608 (0x00800000)

============================================ 

Ralink UBoot Version: 3.3

-------------------------------------------- 

ASIC 3883_MP (MAC to REALTEK Mode)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Total memory: 64 MBytes

Flash component: NOR Flash

Date:Oct 11 2010  Time:14:10:10

============================================ 

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768 

gpio_init: write 0x0000185f to GPIOMODE(0xb0000060)

 Initializing RTL8367 GbE switch ...

 Setting RTL8367R RGMII Delay time 0x08(TX:01,RX:00)

Please choose the operation: 

   1: Load system code to SDRAM via TFTP. 

   2: Load system code then write to Flash via TFTP. 

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   7: Load Boot Loader code then write to Flash via Serial. 

   9: Load Boot Loader code then write to Flash via TFTP. 

 0 

FRESET button pressed, force into HTTP server.

Entering HTTP server.

Using Eth0 (10/100-M) device

Start HTTP server on port 80, 192.168.0.1

Running ...

checksum bad

checksum bad

U-Boot 1.1.3 (Oct 11 2010 - 14:10:10) (ALPHA)

SVN revision: 432

Target board: WRG-ND10

Board: Ralink APSoC DRAM:  64 MB

Flash: Bank 0, ID:00032228, Size 8388608 (0x00800000)

============================================ 

Ralink UBoot Version: 3.3

-------------------------------------------- 

ASIC 3883_MP (MAC to REALTEK Mode)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Total memory: 64 MBytes

Flash component: NOR Flash

Date:Oct 11 2010  Time:14:10:10

============================================ 

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768 

gpio_init: write 0x0000185f to GPIOMODE(0xb0000060)

 Initializing RTL8367 GbE switch ...

 Setting RTL8367R RGMII Delay time 0x08(TX:01,RX:00)

Please choose the operation: 

   1: Load system code to SDRAM via TFTP. 

   2: Load system code then write to Flash via TFTP. 

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   7: Load Boot Loader code then write to Flash via Serial. 

   9: Load Boot Loader code then write to Flash via TFTP. 

You choosed 4

 0 

4: System Enter Boot Command Line Interface.

U-Boot 1.1.3 (Oct 11 2010 - 14:10:10) (ALPHA)

RT3883 # help

?       - alias for 'help'

bootm   - boot application image from memory

cp      - memory copy

erase   - erase FLASH memory

go      - start application at address 'addr'

help    - print online help

httpsvr - Start HTTP server to load image

loadb   - load binary file over serial line (kermit mode)

md      - memory display

mm      - memory modify (auto-incrementing)

mw      - memory write (fill)

nm      - memory modify (constant address)

printenv- print environment variables

protect - enable or disable FLASH write protection

reset   - Perform RESET of the CPU

saveenv - save environment variables to persistent storage

setenv  - set environment variables

spicmd  - read/write data from/to eeprom or vtss

tftpboot- boot image via network using TFTP protocol

version - print monitor version

RT3883 # version

U-Boot 1.1.3 (Oct 11 2010 - 14:10:10) (ALPHA)

RT3883 # printev nv

bootcmd=tftp

bootdelay=1

baudrate=57600

ramargs=setenv bootargs root=/dev/ram rw

addip=setenv bootargs $(bootargs) 
ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname):$(netdev):off

addmisc=setenv bootargs $(bootargs) console=ttyS0,$(baudrate) 
ethaddr=$(ethaddr) panic=1

flash_self=run ramargs addip addmisc;bootm $(kernel_addr) $(ramdisk_addr)

kernel_addr=BFC40000

u-boot=u-boot.bin

load=tftp 8A100000 $(u-boot)

u_b=protect off 1:0-1;era 1:0-1;cp.b 8A100000 BC400000 $(filesize)

loadfs=tftp 8A100000 root.cramfs

u_fs=era bc540000 bc83ffff;cp.b 8A100000 BC540000 $(filesize)

test_tftp=tftp 8A100000 root.cramfs;run test_tftp

ethact=Eth0 (10/100-M)

ethaddr=1c:7e:e5:96:97:77

ipaddr=192.168.0.1

serverip=1.1.1.67

bootfile=david/tftp_wrgnd07_bravo_bwg4200.bin

stdin=serial

stdout=serial

stderr=serial

Environment size: 806/4092 bytes

RT3883 #

Original comment by euan.kir...@gmail.com on 21 Sep 2013 at 2:15

GoogleCodeExporter commented 9 years ago 
I tried sending a trx to the emergency webserver, it just fails and reboots.  
Tried removing the first 32 bytes and renaming *.bin.  Also fails.

Sent the trx to bootloader as option 1 copy to sdram and execute, it works with 
the trx file, but fails to boot sucessfully. 

Log as follows:

U-Boot 1.1.3 (Oct 11 2010 - 14:10:10) (ALPHA)

SVN revision: 432

Target board: WRG-ND10

Board: Ralink APSoC DRAM:  64 MB

Flash: Bank 0, ID:00032228, Size 8388608 (0x00800000)

============================================ 

Ralink UBoot Version: 3.3

-------------------------------------------- 

ASIC 3883_MP (MAC to REALTEK Mode)

DRAM component: 512 Mbits DDR, width 16

DRAM bus: 16 bit

Total memory: 64 MBytes

Flash component: NOR Flash

Date:Oct 11 2010  Time:14:10:10

============================================ 

icache: sets:512, ways:4, linesz:32 ,total:65536

dcache: sets:256, ways:4, linesz:32 ,total:32768 

gpio_init: write 0x0000185f to GPIOMODE(0xb0000060)

 Initializing RTL8367 GbE switch ...

 Setting RTL8367R RGMII Delay time 0x08(TX:01,RX:00)

Please choose the operation: 

   1: Load system code to SDRAM via TFTP. 

   2: Load system code then write to Flash via TFTP. 

   3: Boot system code via Flash (default).

   4: Entr boot command line interface.

   7: Load Boot Loader code then write to Flash via Serial. 

   9: Load Boot Loader code then write to Flash via TFTP. 

You choosed 1

 0 

1: System Load Linux to SDRAM via TFTP. 

 Please Input new ones /or Ctrl-C to discard

    Input device IP (192.168.0.1) ==:192.168.0.1

    Input server IP (192.168.0.19) ==:192.168.0.19

    Input Linux Kernel filename (SWR1100_3.4.3.6-066.trx) ==:SWR1100_3.4.3.6-066.trx     8.trx

Using Eth0 (10/100-M) device

TFTP from server 192.168.0.19; our IP address is 192.168.0.1

Filename 'SWR1100_3.4.3.6-068.trx'.

Loading: *#################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################################

     #################################################Got ARP REQUEST, return our IP

###  done

Bytes transferred = 7254408 (6eb188 hex)

Prepare config sector: ADDR[0xbc030000], SIZE[0x00010000], CONFIG 
SIZE[0x00001000]

Protect off BC030000 ... BC03FFFF

Un-Protected 1 sectors

Erasing Flash...

 done ret=0

Erased 1 sectors

Writing to Flash... done

Protected 1 sectors

Automatic boot of image at addr 0x80800000 ...

## Booting image at 80800000 ...

   Image Name:   SWR1100

   Created:      2013-09-03   6:26:19 UTC

   Image Type:   MIPS Linux Kernel Image (lzma compressed)

   Data Size:    7254344 Bytes =  6.9 MB

   Load Address: 80000000

   Entry Point:  802ccd20

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

Starting kernel ...

LINUX started...

 THIS IS ASIC
Linux version 3.4.60 (padavan@hms) (gcc version 4.4.7 (GCC) ) #1 Tue Sep 3 
10:15:24 MSK 2013

 The CPU frequency set to 500 MHz
CPU revision is: 0001974c (MIPS 74Kc)
Determined physical RAM map:
 memory: 04000000 @ 00000000 (usable)
Zone PFN ranges:
  Normal   0x00000000 -> 0x00004000
Movable zone start PFN for each node
Early memory PFN ranges
    0: 0x00000000 -> 0x00004000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock4 
rootfstype=squashfs
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
Writing ErrCtl register=00000000
Readback ErrCtl register=00000000
Memory: 61108k/65536k available (2899k kernel code, 4428k reserved, 553k data, 
188k init, 0k highmem)
NR_IRQS:65
calculating r4koff... 001e8480(2000000)
CPU frequency 500.00 MHz
console [ttyS1] enabled
Calibrating delay loop... 249.34 BogoMIPS (lpj=498688)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16

*************** Ralink PCIe RC mode *************
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff]
pci_bus 0000:00: root bus resource [io  0x10160000-0x1016ffff]
pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring
pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff]
pci 0000:00:00.0: BAR 1: assigned [mem 0x20100000-0x2010ffff]
pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x2000ffff]
pci 0000:00:00.0: PCI bridge to [bus 01-01]
pci 0000:00:00.0:   bridge window [mem 0x20000000-0x200fffff]
Switching to clocksource MIPS
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RT3xxx EHCI/OHCI init.
squashfs: version 4.0 (2009/01/31) Phillip Lougher
msgmni has been set to 119
alg: No test for stdrng (krng)
io scheduler noop registered (default)
pcieport 0000:00:00.0: device [1814:0802] has invalid IRQ; check vendor BIOS
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
Ralink gpio driver initialized
Number of GPIO: 52, GPIO mode: 0000185F
brd: module loaded
loop: module loaded
ralink flash device: 0x1000000 at 0x1c000000
Ralink SoC physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. 
Manufacturer ID 0x0000c2 Chip ID 0x00227e
Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.3.
number of CFI chips: 1
Creating 7 MTD partitions on "Ralink SoC physically mapped flash":
0x000000000000-0x000000030000 : "Bootloader"
0x000000030000-0x000000040000 : "Config"
0x000000040000-0x000000050000 : "Factory"
0x000000050000-0x000065050000 : "Kernel"
mtd: partition "Kernel" extends beyond the end of device "Ralink SoC physically 
mapped flash" -- size truncated to 0x7b0000
0x000000800000-0x00009bfa0000 : "RootFS"
mtd: partition "RootFS" is out of reach -- disabled
0x000000000000-0x000000010000 : "Storage"
0x000000050000-0x000000800000 : "Firmware_Stub"
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
PPP generic driver version 2.4.2
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPTP driver version 0.8.5
PROC INIT OK!
Ralink APSoC Ethernet Driver v3.0.5. Rx Ring: 256, Tx Ring: 256. Max packet 
size: 1536.
rtl8367 - hw bridge: W|LLLL
Realtek RTL8367 GigaPHY Switch Driver v1.9.
usbcore: registered new interface driver libusual
nf_conntrack version 0.5.0 (16384 buckets, 32768 max)
xt_time: kernel timezone is -0000
gre: GRE over IPv4 demultiplexor driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP: cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
Bridge firewalling registered
L2TP core driver, V2.0
PPPoL2TP kernel driver, V2.0
8021q: 802.1Q VLAN Support v1.8
ASUS NVRAM: initialized. Available NVRAM space: 61440
end_request: I/O error, dev mtdblock4, sector 0
SQUASHFS error: squashfs_read_data failed to read block 0x0
SQUASHFS error: unable to read squashfs_super_block
VFS: Cannot open root device "mtdblock4" or unknown-block(31,4): error -5
Please append a correct "root=" boot option; here are the available partitions:
1f00             192 mtdblock0  (driver?)
1f01              6

Original comment by euan.kir...@gmail.com on 21 Sep 2013 at 2:39

GoogleCodeExporter commented 9 years ago 
missing last section:

VFS: Cannot open root device "mtdblock4" or unknown-block(31,4): error -5
Please append a correct "root=" boot option; here are the available partitions:
1f00             192 mtdblock0  (driver?)
1f01              64 mtdblock1  (driver?)
1f02              64 mtdblock2  (driver?)
1f03            7872 mtdblock3  (driver?)
1f05              64 mtdblock5  (driver?)
1f06            7872 mtdblock6  (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,4)

Original comment by euan.kir...@gmail.com on 21 Sep 2013 at 2:40

GoogleCodeExporter commented 9 years ago 
Info on the serial debug terminal:

JP1 Pin 1: RX  (pin 1 is first pin on left further away from all the others, 
its also square which is the usual keying indicator)
JP1 Pin 2: 3.3vdc
JP1 Pin 1: GND
JP1 Pin 1: TX

Baud is 57600,8,N,1 no hardware handshake (obviously)

I used a TTL-3.3-USB converter from RS Components, a MAX232 IC type device 
would also work.

Part details:
429-303 $25.00  RS232 to USB converter cable,with wire ends,TTL-232R-3v3-WE

Original comment by euan.kir...@gmail.com on 21 Sep 2013 at 3:00

GoogleCodeExporter commented 9 years ago 
[deleted comment]
GoogleCodeExporter commented 9 years ago 
Hello, 

Do I need Linux machine in order to flash TRX file to CY-SWR1100 router serial 
debug terminal ?

I have TTL-3.3-USB converter. I need help with instructions on the flashing 
process please. 

Thank you!

Original comment by fma...@gmail.com on 29 Nov 2013 at 8:53

GoogleCodeExporter commented 9 years ago 
No, you don't need linux. Please read here 
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=82160&postdays=0&postorder=asc&star
t=0. Flashing procedure is about same.

Original comment by rad...@khadonov.ru on 29 Nov 2013 at 12:50

GoogleCodeExporter commented 9 years ago 
Thank you !!

Original comment by fma...@gmail.com on 29 Nov 2013 at 8:56

GoogleCodeExporter commented 9 years ago 
Sorry to bring this back.
Is this file SWR1100_3.4.3.7-078.trx the modified rt-n56u firmware?

I do tried both ways(WebGUI and Emergency Mode) to do it, both showed "Invalid 
Image File"

I am newbie to the console/serial part. Can anyone tell me what to do next?

Thanks

Original comment by MurphySt...@gmail.com on 12 Mar 2014 at 3:38

GoogleCodeExporter commented 9 years ago 
I read a lot of differences how to put the firmware on the swr1100 router. Can 
you please explain the best way how to get it work. I tried the last base-trx 
file. It will not flash. Even in Emergency Mode (IP is 192.168.0.1). The ASUS 
Firmware Restoration Utility can't connect te router. I'm looking forward tot 
use your firmware.

Original comment by fjchoeks...@gmail.com on 14 May 2014 at 7:17

GoogleCodeExporter commented 9 years ago 
[deleted comment]
GoogleCodeExporter commented 9 years ago 
Thanks for the work, but without detailed instructions on how to install the 
firmware on CY-SWR1100, the work is useless. It is like giving a starving child 
a locked box, which has foods in it, without the key.
Please give us the instructions.

Original comment by typing...@gmail.com on 4 Aug 2014 at 2:12

GoogleCodeExporter commented 9 years ago 
I have been unable to get it to flash either 12+ months down the track!

Original comment by harri...@isabarwon.com on 4 Aug 2014 at 2:56

GoogleCodeExporter commented 9 years ago 
Thanks harry... for the response. It seems the developers has abandoned 
CY-SWR1100. I have wasted a few hours today. I think I would rather buy a new 
router that are compatible with WRT softwares.

Original comment by typing...@gmail.com on 4 Aug 2014 at 3:24

GoogleCodeExporter commented 9 years ago 
http://www.dd-wrt.com/phpBB2/viewtopic.php?t=268169

Original comment by rad...@khadonov.ru on 4 Sep 2014 at 7:08