Web server not responding anymore in V3.6.0

[RonaldSpijk]

I've uploaded version 3.6.0 on a newly bought SmartEVSE. Before that it had 3.5.1 for a few days. It worked for a few days without any problems.

After some issues with the Wifi the web server stopped working. MQTT still works. I can also ping. When accessing port 80 the port is found, but the connection is dropped immediately.

A tried resetting a few times, doesn't help. A tried starting the Wifi Portal, this also doesn't work.

Fortunately, charging still works :-)

I'm stuck in the middle here, because when the web server doesn't work, I can't update, and get logs. I'm afraid to do anything else, because it might brick my SmartEVSE.

I think this needs good investigation because it might also occur at other users. And I like some help getting a working version on the SmartEVSE. Would uploading the bin file with the Espressif flash download tool work? Or should I try something else first.

[dingo35]

Dont be afraid, AFAIK you cannot brick your SmartEVSE, you can always flash a new version through the built in USB-C bus.

If the MQTT server is connected, it means your wifi is connected, which should mean your webserver is connected.

Are you sure you are surfing to http://ipaddress-of-your-smartevse? Some browsers try to redirect you to https, which will not work (not at 3.6.0, spoiler alert!)

You can also try to go to http://ip/update for direct update

Or try another browser?

[RonaldSpijk]

I tried the IP address, the SmartEVSE name, the DHCP name. I tried various browsers, chrome F12, curl. All with the same result.

Ping works fine, however when accessing port 80 the connection is dropped. When accessing another port (e.g. 81) the connection is never made.

When I use 'curl -X GET http://ipaddress-of-smartevse/settings' it replies 'Recv failure: Connection reset by peer.' I also tried to post some settings to see if the commands get there, but nothing changes.

[dingo35]

What always works is reflashing, instructions see bottom of page https://github.com/dingo35/SmartEVSE-3.5/blob/master/docs/configuration.md

[AndrejSNC]

What I have discovered today is, I replaced my old SmartEVSE version with V3 controller. It came with 3.0.1 SW version. I connected it to WiFi and set fixed IP address - works great. Then I updated it to 3.6.0 it connected back to the old dynamic IP address, which I don't like. I can start WiFi setup in menu, connect to access point but the configuration page does not open on my phone. How can I access this configuration, to set back static IP? Tried 192.168.4.1 and it did not connect.

[dingo35]

If you set "wifi" from "Enabled" to "Setup" on the LCD screen, you should be able to connect to the SmartEVSE AP via 192.168.4.1 and set a static IP.

If it for some reason that fails, you can always goto /erasesettings and repeat the wifi setup procedure.

[deekoowee]

Similar problem here. Controlled worked until I upgrade it to 3.6.0 Controller answer for ping at 192.168.4.1, but do not answer to browser. Tried with Chrome and Curl Also tried the /erasesettings, but no luck. I tried to flash the firmware with ESP32 flash download tool v3.9.6 , but nothing changed Connected serial cable and telnet shows; Any suggestions to fix the controller's firmware

[dingo35]

If you have these problems with 3.6.0, why dont you downgrade to 3.5.1 with USB-C cable? Link is posted in this thread....

[deekoowee]

Downgraded to 3.5.1 via USB-C cable, rebooted controller, the web page showup. Showed version 3.6.0 at left top corner of the screen After few minutes, the webserver has lost, no communication with any browser. Some mystery, which I don't catch up.

[dingo35]

Your downgrade obviously did not succeed...

EDIT: Make sure you add the -t upload parameter when compiling; you should see messages like 10% written, 20% , etc.

[deekoowee]

I tried to upload the firmware.bin file with ESP32 flash download tool v3.9.6 (downloaded from Espressif site) I used settings like this, only filename was changed. the bar at bottom on window runs ok.

[mstegen]

There are two partitions, the first one starts at 0x10000 The second one starts at 0x1c0000 Try flashing both partitions. That should do the trick.

[deekoowee]

Flashing those two partitions together fixed the webaccess problem

All settings were gone and have to reconfigure the controller

[dingo35]

The settings were gone because you did /erasesettings, not because of reflashing those two partitions...

[deekoowee]

Yes, I noticed that. It is not big deal to make new settings again

[dingo35]

This should solve the problem: 83adad145a90903.zip

[deekoowee]

I have tested more the 3.5.1 and 3.6.1 Both give Communication errors. LCD screen have "ERROR NO SERIAL COM CHECK CFG OR WIRING" and pushbuttton light blinks fast red. Wiring has not changed and config should be ok, because I downgrade to 1.8.0 and it doesn't give any errors.

[AlbertHakvoort]

This should solve the problem: 83adad145a90903.zip

I've had the same issue, the 83adad145a90903.zip is fixed the webserver issue

[dingo35]

Thanks for your reports guys, this should be solved in 3.6.1 .