emilioamores ardupilot-mega issues

emilioamores / ardupilot-mega

Automatically exported from code.google.com/p/ardupilot-mega

0 stars 0 forks source link

issues

Newest

Newest Most commented Recently updated Oldest Least commented Least recently updated

Error build ArduCopter in elcipse

#981 GoogleCodeExporter opened 9 years ago
0
Simplified and geofence

#980 GoogleCodeExporter opened 9 years ago
0
Use google map elevations to establisk landing altitude when landing at other elevation

#979 GoogleCodeExporter opened 9 years ago
1
cli no longer accessible with Mission Planner 1.3.15

#978 GoogleCodeExporter opened 9 years ago
0
"Load settings" is breaking up communication in air of 3DR Radio

#977 GoogleCodeExporter opened 9 years ago
0
Stop at "Got param RC6_TRIM"

#976 GoogleCodeExporter opened 9 years ago
0
Enhancement request

#975 GoogleCodeExporter opened 9 years ago
0
Arduino installation damaged version 1.0.3 OSX

#974 GoogleCodeExporter opened 9 years ago
0
No CH6-8 options for tuning etc. in Arduplane

#973 GoogleCodeExporter opened 9 years ago
0
Suggested FAA Ban on ANY Weapon aboard ANY RC Model.

#972 GoogleCodeExporter opened 9 years ago
0
Motors arm in Stability mode and spin but no throttle response above minimum rpm

#971 GoogleCodeExporter opened 9 years ago
0
condition change alt just not working

#970 GoogleCodeExporter opened 9 years ago
0
Mission Planner reports NO GPS while secondary GPS is up and reporting.

#969 GoogleCodeExporter opened 9 years ago
0
SoftwareSerial.h

#968 GoogleCodeExporter opened 9 years ago
0
Waypoints garbled in Mission Planner when reading from the ground with a mission onscreen

#967 GoogleCodeExporter opened 9 years ago
0
Heli-setup, cannot correctly adjust values

#966 GoogleCodeExporter opened 9 years ago
0
Can't connect to MP with usb or 3dr-wireless

#965 GoogleCodeExporter opened 9 years ago
0
Tail spin

#964 GoogleCodeExporter opened 9 years ago
0
debugg arducopter code modification by printing to serial port

#963 GoogleCodeExporter opened 9 years ago
0
NMEA COM-Output wrong?

#962 GoogleCodeExporter opened 9 years ago
0
How about jets?

#961 GoogleCodeExporter opened 9 years ago
0
wrong display in MP

#960 GoogleCodeExporter opened 9 years ago
0
RC channel [SBUS] of Pixhawk in mission planner has no respose to transmitter

#959 GoogleCodeExporter opened 9 years ago
1
Planner takes a long time/hangs to download the plane parameters if the baud rate is low.

#958 GoogleCodeExporter opened 9 years ago
0
Misson planner forgets Telemetry rates if you disconnect from remote unit, and re-connect.

#957 GoogleCodeExporter opened 9 years ago
0
Wizard accelerometer calibration cannot be corrected after fail

#956 GoogleCodeExporter opened 9 years ago
0
Wiki link in FailSafe setup not working

#955 GoogleCodeExporter opened 9 years ago
0
'Calibrate Level' completion indication is confusing

#954 GoogleCodeExporter opened 9 years ago
0
Auto Grid Ui issue

#953 GoogleCodeExporter opened 9 years ago
0
WP list incorrectly read from APM by MissionPlanner

#952 GoogleCodeExporter opened 9 years ago
0
Coordinated Flight WP_YAW_BEHAVIOR

#951 GoogleCodeExporter opened 9 years ago
0
internal gpx log is no longer collecting data

#950 GoogleCodeExporter opened 9 years ago
0
Issues with EM-506 GPS

#949 GoogleCodeExporter opened 9 years ago
0
Mission Planner cant open BT serial port

#948 GoogleCodeExporter opened 9 years ago
1
Ability to set speed between waypoints

#947 GoogleCodeExporter opened 9 years ago
0
QGroundControl build error.

#946 GoogleCodeExporter opened 9 years ago
0
建議加入也可設攝影鏡頭/無人機前方固定何一座標

#945 GoogleCodeExporter opened 9 years ago
0
Mission Planner not working with non-US locale

#944 GoogleCodeExporter opened 9 years ago
1
Grid UI tool won't accept leg spacing greater than 500M

#943 GoogleCodeExporter opened 9 years ago
0
LED_MODE available in APM:Plane

#942 GoogleCodeExporter opened 9 years ago
0
Enhancement request

#941 GoogleCodeExporter opened 9 years ago
0
Servo postion log APM

#940 GoogleCodeExporter opened 9 years ago
0
boot up probs

#939 GoogleCodeExporter opened 9 years ago
0
what battery info. should I enter with Power module used when clicking for verbal alert box?

#938 GoogleCodeExporter opened 9 years ago
0
DS1820 temperature measurement

#937 GoogleCodeExporter opened 9 years ago
0
Compass Orientation Screen 1.2.65

#936 GoogleCodeExporter opened 9 years ago
0
Arduplane 2.74b no logs !

#935 GoogleCodeExporter opened 9 years ago
0
Plot vertical speed on the mission planer map

#934 GoogleCodeExporter opened 9 years ago
0
VB error in Mission Planner

#933 GoogleCodeExporter opened 9 years ago
1
Arduplane V2.74b problem

#932 GoogleCodeExporter opened 9 years ago
2