JasperRowan commented 6 years ago

Hardware:

Board: ESP32 DEVKIT V1 (www.doit.am) Based on ESP-WROOM-32 Module
Core Installation/update date: 18/jul/2018 IDE name: Arduino IDE 1.8.5 (windows store 1.8.10.0) (Windoes 10) Flash Frequency: 80Mhz Upload Speed: 115200

Description:

I am trying to use DeepSleep to help with power consumption in a battery power project where I am using esp32s to monitor a sensor and report data back to a receiving esp32 using the ESP NOW protocol. I tried to use the 3 examples under ESP32/DeepSleep to get an understanding of how DeepSleep works. I thought the most simple example was the TimerWakeUp, but once I uploaded it and checked the serial monitor I realized that none of the serial prints were being called. The board reset successfully every five seconds and the current dropped every sleep cycle from around 50 mA to 9mA so it seems to be partially working.

(I have 5 of these ESP32 DEVKIT V1 boards (ordered altogether from Amazon) and I got the same result on all five... was also able to get ESP NOW working on them with no problem)

Thanks for your help

-Jasper

Sketch:

/* Simple Deep Sleep with Timer Wake Up

ESP32 offers a deep sleep mode for effective power saving as power is an important factor for IoT applications. In this mode CPUs, most of the RAM, and all the digital peripherals which are clocked from APB_CLK are powered off. The only parts of the chip which can still be powered on are: RTC controller, RTC peripherals ,and RTC memories

This code displays the most basic deep sleep with a timer to wake it up and how to store data in RTC memory to use it over reboots

This code is under Public Domain License.

Author: Pranav Cherukupalli cherukupallip@gmail.com */

define uS_TO_S_FACTOR 1000000 / Conversion factor for micro seconds to seconds /

define TIME_TO_SLEEP 5 / Time ESP32 will go to sleep (in seconds) /

RTC_DATA_ATTR int bootCount = 0;

/ Method to print the reason by which ESP32 has been awaken from sleep / void print_wakeup_reason(){ esp_sleep_wakeup_cause_t wakeup_reason;

wakeup_reason = esp_sleep_get_wakeup_cause();

switch(wakeup_reason) { case 1 : Serial.println("Wakeup caused by external signal using RTC_IO"); break; case 2 : Serial.println("Wakeup caused by external signal using RTC_CNTL"); break; case 3 : Serial.println("Wakeup caused by timer"); break; case 4 : Serial.println("Wakeup caused by touchpad"); break; case 5 : Serial.println("Wakeup caused by ULP program"); break; default : Serial.println("Wakeup was not caused by deep sleep"); break; } }

void setup(){ Serial.begin(115200); delay(1000); //Take some time to open up the Serial Monitor

//Increment boot number and print it every reboot ++bootCount; Serial.println("Boot number: " + String(bootCount));

//Print the wakeup reason for ESP32 print_wakeup_reason();

/ First we configure the wake up source We set our ESP32 to wake up every 5 seconds / esp_sleep_enable_timer_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR); Serial.println("Setup ESP32 to sleep for every " + String(TIME_TO_SLEEP) + " Seconds");

/ Next we decide what all peripherals to shut down/keep on By default, ESP32 will automatically power down the peripherals not needed by the wakeup source, but if you want to be a poweruser this is for you. Read in detail at the API docs http://esp-idf.readthedocs.io/en/latest/api-reference/system/deep_sleep.html Left the line commented as an example of how to configure peripherals. The line below turns off all RTC peripherals in deep sleep. / //esp_deep_sleep_pd_config(ESP_PD_DOMAIN_RTC_PERIPH, ESP_PD_OPTION_OFF); //Serial.println("Configured all RTC Peripherals to be powered down in sleep");

/ Now that we have setup a wake cause and if needed setup the peripherals state in deep sleep, we can now start going to deep sleep. In the case that no wake up sources were provided but deep sleep was started, it will sleep forever unless hardware reset occurs. / Serial.println("Going to sleep now"); esp_deep_sleep_start(); Serial.println("This will never be printed"); }

void loop(){ //This is not going to be called }

Debug Messages:

ets Jun 8 2016 00:22:57

rst:0x5 (DEEPSLEEP_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:808 load:0x40078000,len:6084 load:0x40080000,len:6696 entry 0x400802e4 Boot ets Jun 8 2016 00:22:57

This just loops forever

tonu42 commented 6 years ago

The board reset successfully every five seconds and the current dropped every sleep cycle from around 50 mA to 9mA so it seems to be partially working.

So the sketch is working.

This just loops forever

This is being called in the code each time the device wakes up: print_wakeup_reason();

Although I think the messages you are seeing over and over again are merely the initial prints that the chip always does.

rst:0x5 (DEEPSLEEP_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)

Shows you that the device is being reset by the deepsleep reset proccess.

JasperRowan commented 6 years ago

Ok,

thank you for your quick response!

My understanding is that this each time the esp32 wakes up it will run the setup function. I am still confused about why the print_wakeup_reason(); and Serial.println("Going to sleep now"); are not printing to the serial monitor. In the print_wakeup_reason(); function each serial print begins with "Wakeup caused by..." or "Wakeup was not caused by..." but I never see that in the serial monitor. I'm sorry if I'm missing something very obvious, I'm new to microcontrollers in general but especially the esp32.

Thank you so much for your time.

-Jasper

On Thu, Aug 23, 2018 at 1:48 PM, tonu42 notifications@github.com wrote:

The board reset successfully every five seconds and the current dropped every sleep cycle from around 50 mA to 9mA so it seems to be partially working.

So the sketch is working.

This just loops forever

This is being called in the code each time the device wakes up: print_wakeup_reason();

Although I think the messages you are seeing over and over again are merely the initial prints that the chip always does.

rst:0x5 (DEEPSLEEP_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)

Shows you that the device is being reset by the deepsleep reset proccess.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/espressif/arduino-esp32/issues/1790#issuecomment-415565979, or mute the thread https://github.com/notifications/unsubscribe-auth/AisujzCoPwRVnnt87HlEEljsPwpWL7xIks5uTxUQgaJpZM4WKDSV .

lbernstone commented 6 years ago

Put in a delay(100) right before the sleep. There is not enough time to print everything to serial before it goes to sleep.

JasperRowan commented 6 years ago

Thank you so much for your fast response. That solved the problem!

JasperRowan commented 6 years ago

That was it! thank you.

On Thu, Aug 23, 2018 at 2:33 PM, lbernstone notifications@github.com wrote:

Put in a delay(100) right before the sleep. There is not enough time to print everything to serial before it goes to sleep.

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/espressif/arduino-esp32/issues/1790#issuecomment-415578133, or mute the thread https://github.com/notifications/unsubscribe-auth/Aisuj3-xI81s4cOSpgzoe3OSUQjwTxn0ks5uTx-dgaJpZM4WKDSV .

entropia1ac commented 6 years ago

It does not work for me-no wake up. (Board: TTGO LORA32) ........ void setup(){ Serial.begin(115200); delay(1000); //Take some time to open up the Serial Monitor ++bootCount; Serial.println("Boot number: " + String(bootCount)); print_wakeup_reason();

Serial.flush(); delay(1000); esp_sleep_enable_timer_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR); Serial.println("Setup ESP32 to sleep for every " + String(TIME_TO_SLEEP) + " Seconds"); }

.....

entropia1ac commented 6 years ago

not work -no going to sleep. (Board: TTGO LORA32 ,stable release 1.0.0) ........ void setup(){ Serial.begin(115200); delay(1000); //Take some time to open up the Serial Monitor ++bootCount; Serial.println("Boot number: " + String(bootCount)); print_wakeup_reason();

Serial.flush(); delay(1000); esp_sleep_enable_timer_wakeup(TIME_TO_SLEEP * uS_TO_S_FACTOR); Serial.println("Setup ESP32 to sleep for every " + String(TIME_TO_SLEEP) + " Seconds"); } void loop(){ Serial.println("Boot number in loop=" + String(bootCount)); delay(1000); } ..... debug:============== ets Jun 8 2016 00:22:57

rst:0x1 (POWERON_RESET),boot:0x17 (SPI_FAST_FLASH_BOOT) configsip: 0, SPIWP:0xee clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00 mode:DIO, clock div:1 load:0x3fff0018,len:4 load:0x3fff001c,len:808 load:0x40078000,len:6084 load:0x40080000,len:6696 entry 0x400802e4 Boot number: 1 Wakeup was not caused by deep sleep Setup ESP32 to sleep for every 5 Seconds Boot number in loop=1 Boot number in loop=1 Boot number in loop=1 Boot number in loop=1 Boot number in loop=1 Boot number in loop=1 Boot number in loop=1 Boot number in loop=1 Boot number in loop=1

Lejaco13 commented 5 years ago

You forget to put that:

esp_deep_sleep_start();

Lejaco13 commented 5 years ago

The better board for the low power consumption "DeepSleep" (10 μA) is from the manufacturer DFRobot. FireBeetle ESP32

https://www.dfrobot.com/product-1590.html

espressif / arduino-esp32

ESP32 Deep Sleep Examples not working as expected #1790

Hardware:

Description:

Sketch:

/* Simple Deep Sleep with Timer Wake Up

define uS_TO_S_FACTOR 1000000 / Conversion factor for micro seconds to seconds /

define TIME_TO_SLEEP 5 / Time ESP32 will go to sleep (in seconds) /

Debug Messages: