Closed kai-morich closed 6 months ago
Was ist hier die Fehlerbeschreibung?
Es schaltet nicht von 3 Phasen auf 1 Phase runter, sondern wechselt periodisch zwischen 3 Phasen und Aus. Das Problem tritt nicht immer, aber doch häufig auf.
Wenn für 1p nicht genug Leistung da ist- warum sollte er dann auf 1p gehen? "Aus" ist in diesem Fall richtig.
/cc @MarkusGH
Es ist genügend Leistung für 1p vorhanden, wie im Grafana Chart zu sehen (linke Achse ist Watt, grün ist PV-Ertrag und blau Linie = hellgrüne Fläche die Wallbox)
Evcc ist wohl der Annahme das es gleich wieder auf 3p hochschalten soll, und die Easee ist dann erst mal ein paar Minuten beleidigt, weil die Umschaltung zu oft wäre.
[lp-1 ] DEBUG 2024/03/09 14:06:18 available power 7068W > 4140W min 3p threshold
@andig: Ich glaube nicht, dass das mit https://github.com/evcc-io/evcc/pull/11878 zu tun hat.
Das Log sieht seltsam aus. evcc scheint das richtige tun zu wollen:
[lp-1 ] DEBUG 2024/03/09 14:05:14 phase scale1p in 27s
[lp-1 ] DEBUG 2024/03/09 14:05:44 phase scale1p in 0s
[lp-1 ] DEBUG 2024/03/09 14:05:44 switched phases: 1p
[lp-1 ] DEBUG 2024/03/09 14:05:44 phase timer inactive
[lp-1 ] DEBUG 2024/03/09 14:05:44 projected site power 1008W >= 0W disable threshold
[lp-1 ] DEBUG 2024/03/09 14:05:44 pv disable timer start: 3m0s
[lp-1 ] DEBUG 2024/03/09 14:05:44 pv disable in 3m0s
[lp-1 ] DEBUG 2024/03/09 14:06:14 charger status: B
[lp-1 ] INFO 2024/03/09 14:06:14 stop charging <-
Aber die Easee bzw. die Anbindung führt es nicht richtig aus. Habe einen Verdacht - schaue gleich mal nach.
Irgendwie sehen die Messwerte komisch aus.
[site ] DEBUG 2024/03/09 14:06:14 site power: -2831W
...
[lp-1 ] DEBUG 2024/03/09 14:06:18 available power 7068W > 4140W min 3p threshold
Die Site sieht 2.8kW verfügbaren Überschuss, und der Loadpoint 7kW. Oder sehe ich das falsch?
@GrimmiMeloni: Mach Dir keine Gedanken - ich denke ich weiß an was es liegt.
@GrimmiMeloni, @andig: Ich hatte schon ein schlechtes Gefühl wegen https://github.com/evcc-io/evcc/pull/9075, dachte aber solange sich keiner beschwert wird es schon passen...
Die Site sieht 2.8kW verfügbaren Überschuss, und der Loadpoint 7kW. Oder sehe ich das falsch?
@GrimmiMeloni: Unabhängig von der Ursache des Bugs hier ist das tatsächlich seltsam.
Describe the bug
um 14:05 schaltet evcc auf 1 Phase runter
kurze Zeit später glaubt evcc, das genug Energie für 3 Phasen zu 16A vorhanden wäre, und schaltet wieder zurück auf 3 Phasen, aber ohne die übliche Wartezeit
Wahrscheinlich wegen Schaltschutz führt die Easee dies deutlich später aus. Warum nur 6A statt 16A ist mir rätselhaft, aber wahrscheinlich nur ein Folgefehler
Danach wiederholt sich das Spiel.
Wird ein zu häufiges Umschalten wie um 14:06 nicht eigentlich verhindert?
Steps to reproduce
weniger Sonne
Configuration details
Log details
What type of operating system are you running?
Linux
Version
0.124.8