Is the TP Link Archer T4U V3 supports AP mode???

I'm having doubt since I bought this device and was testing Evil Twin attack but DHCP service was not getting started. I searched and somewhere written its a driver issue and somewhere that adapter might not support AP mode.

I'm giving output of iw list command. please check and let me know if it support AP mode.?

PS: Phy1 is TP link archer V3 and Phy0 is my laptop internal wireless card.

└─# iw list Wiphy phy2 wiphy index: 2 max # scan SSIDs: 9 max scan IEs length: 2304 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Supported Ciphers:

WEP40 (00-0f-ac:1)
WEP104 (00-0f-ac:5)
TKIP (00-0f-ac:2)
CCMP-128 (00-0f-ac:4)
CMAC (00-0f-ac:6) Available Antennas: TX 0 RX 0 Supported interface modes:
- IBSS
- managed
- AP
- monitor
- P2P-client
- P2P-GO Band 1: Capabilities: 0x1963 RX LDPC HT20/HT40 Static SM Power Save RX HT20 SGI RX HT40 SGI RX STBC 1-stream Max AMSDU length: 7935 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT Max RX data rate: 300 Mbps HT TX/RX MCS rate indexes supported: 0-15 Bitrates (non-HT):
  - 1.0 Mbps
  - 2.0 Mbps
  - 5.5 Mbps
  - 11.0 Mbps
  - 6.0 Mbps
  - 9.0 Mbps
  - 12.0 Mbps
  - 18.0 Mbps
  - 24.0 Mbps
  - 36.0 Mbps
  - 48.0 Mbps
  - 54.0 Mbps Frequencies:
  - 2412 MHz [1] (30.0 dBm)
  - 2417 MHz [2] (30.0 dBm)
  - 2422 MHz [3] (30.0 dBm)
  - 2427 MHz [4] (30.0 dBm)
  - 2432 MHz [5] (30.0 dBm)
  - 2437 MHz [6] (30.0 dBm)
  - 2442 MHz [7] (30.0 dBm)
  - 2447 MHz [8] (30.0 dBm)
  - 2452 MHz [9] (30.0 dBm)
  - 2457 MHz [10] (30.0 dBm)
  - 2462 MHz [11] (30.0 dBm)
  - 2467 MHz [12] (disabled)
  - 2472 MHz [13] (disabled)
  - 2484 MHz [14] (disabled) Band 2: Capabilities: 0x1863 RX LDPC HT20/HT40 Static SM Power Save RX HT20 SGI RX HT40 SGI No RX STBC Max AMSDU length: 7935 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT Max RX data rate: 300 Mbps HT TX/RX MCS rate indexes supported: 0-15 VHT Capabilities (0x03d071b2): Max MPDU length: 11454 Supported Channel Width: neither 160 nor 80+80 RX LDPC short GI (80 MHz) TX STBC SU Beamformee MU Beamformee +HTC-VHT VHT RX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT RX highest supported: 867 Mbps VHT TX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT TX highest supported: 867 Mbps Bitrates (non-HT):
  - 6.0 Mbps
  - 9.0 Mbps
  - 12.0 Mbps
  - 18.0 Mbps
  - 24.0 Mbps
  - 36.0 Mbps
  - 48.0 Mbps
  - 54.0 Mbps Frequencies:
  - 5180 MHz [36] (23.0 dBm)
  - 5200 MHz [40] (23.0 dBm)
  - 5220 MHz [44] (23.0 dBm)
  - 5240 MHz [48] (23.0 dBm)
  - 5260 MHz [52] (23.0 dBm) (radar detection)
  - 5280 MHz [56] (23.0 dBm) (radar detection)
  - 5300 MHz [60] (23.0 dBm) (radar detection)
  - 5320 MHz [64] (23.0 dBm) (radar detection)
  - 5500 MHz [100] (23.0 dBm) (radar detection)
  - 5520 MHz [104] (23.0 dBm) (radar detection)
  - 5540 MHz [108] (23.0 dBm) (radar detection)
  - 5560 MHz [112] (23.0 dBm) (radar detection)
  - 5580 MHz [116] (23.0 dBm) (radar detection)
  - 5600 MHz [120] (disabled)
  - 5620 MHz [124] (disabled)
  - 5640 MHz [128] (disabled)
  - 5660 MHz [132] (23.0 dBm) (radar detection)
  - 5680 MHz [136] (23.0 dBm) (radar detection)
  - 5700 MHz [140] (23.0 dBm) (radar detection)
  - 5720 MHz [144] (disabled)
  - 5745 MHz [149] (30.0 dBm)
  - 5765 MHz [153] (30.0 dBm)
  - 5785 MHz [157] (30.0 dBm)
  - 5805 MHz [161] (30.0 dBm)
  - 5825 MHz [165] (30.0 dBm)
  - 5845 MHz [169] (disabled)
  - 5865 MHz [173] (disabled)
  - 5885 MHz [177] (disabled) Supported commands:
- new_interface
- set_interface
- new_key
- start_ap
- new_station
- set_bss
- join_ibss
- set_pmksa
- del_pmksa
- flush_pmksa
- remain_on_channel
- frame
- set_wiphy_netns
- set_channel
- connect
- disconnect WoWLAN support:
- wake up on anything (device continues operating normally) software interface modes (can always be added):
- monitor interface combinations are not supported Device supports SAE with AUTHENTICATE command Device supports scan flush. max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Supported TX frame types:
- IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types:
- IBSS: 0xd0
- managed: 0x40 0xb0 0xd0
- AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- P2P-client: 0x40 0xd0
- P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0 Supported extended features: Wiphy phy0 wiphy index: 0 max # scan SSIDs: 4 max scan IEs length: 2243 bytes max # sched scan SSIDs: 0 max # match sets: 0 Retry short limit: 7 Retry long limit: 4 Coverage class: 0 (up to 0m) Device supports T-DLS. Supported Ciphers:
WEP40 (00-0f-ac:1)
WEP104 (00-0f-ac:5)
TKIP (00-0f-ac:2)
CCMP-128 (00-0f-ac:4)
CCMP-256 (00-0f-ac:10)
GCMP-128 (00-0f-ac:8)
GCMP-256 (00-0f-ac:9)
CMAC (00-0f-ac:6)
CMAC-256 (00-0f-ac:13)
GMAC-128 (00-0f-ac:11)
GMAC-256 (00-0f-ac:12) Available Antennas: TX 0x3 RX 0x3 Configured Antennas: TX 0x3 RX 0x3 Supported interface modes:
- IBSS
- managed
- AP
- AP/VLAN
- monitor
- mesh point Band 1: Capabilities: 0x196f RX LDPC HT20/HT40 SM Power Save disabled RX HT20 SGI RX HT40 SGI RX STBC 1-stream Max AMSDU length: 7935 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT Max RX data rate: 300 Mbps HT TX/RX MCS rate indexes supported: 0-15, 32 Bitrates (non-HT):
  - 1.0 Mbps
  - 2.0 Mbps
  - 5.5 Mbps
  - 11.0 Mbps
  - 6.0 Mbps
  - 9.0 Mbps
  - 12.0 Mbps
  - 18.0 Mbps
  - 24.0 Mbps
  - 36.0 Mbps
  - 48.0 Mbps
  - 54.0 Mbps Frequencies:
  - 2412 MHz [1] (30.0 dBm)
  - 2417 MHz [2] (30.0 dBm)
  - 2422 MHz [3] (30.0 dBm)
  - 2427 MHz [4] (30.0 dBm)
  - 2432 MHz [5] (30.0 dBm)
  - 2437 MHz [6] (30.0 dBm)
  - 2442 MHz [7] (30.0 dBm)
  - 2447 MHz [8] (30.0 dBm)
  - 2452 MHz [9] (30.0 dBm)
  - 2457 MHz [10] (30.0 dBm)
  - 2462 MHz [11] (30.0 dBm)
  - 2467 MHz [12] (30.0 dBm)
  - 2472 MHz [13] (30.0 dBm)
  - 2484 MHz [14] (disabled) Band 2: Capabilities: 0x196f RX LDPC HT20/HT40 SM Power Save disabled RX HT20 SGI RX HT40 SGI RX STBC 1-stream Max AMSDU length: 7935 bytes DSSS/CCK HT40 Maximum RX AMPDU length 65535 bytes (exponent: 0x003) Minimum RX AMPDU time spacing: 16 usec (0x07) HT Max RX data rate: 300 Mbps HT TX/RX MCS rate indexes supported: 0-15, 32 VHT Capabilities (0x03d071b2): Max MPDU length: 11454 Supported Channel Width: neither 160 nor 80+80 RX LDPC short GI (80 MHz) TX STBC SU Beamformee MU Beamformee +HTC-VHT VHT RX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT RX highest supported: 780 Mbps VHT TX MCS set: 1 streams: MCS 0-9 2 streams: MCS 0-9 3 streams: not supported 4 streams: not supported 5 streams: not supported 6 streams: not supported 7 streams: not supported 8 streams: not supported VHT TX highest supported: 780 Mbps Bitrates (non-HT):
  - 6.0 Mbps
  - 9.0 Mbps
  - 12.0 Mbps
  - 18.0 Mbps
  - 24.0 Mbps
  - 36.0 Mbps
  - 48.0 Mbps
  - 54.0 Mbps Frequencies:
  - 5180 MHz [36] (23.0 dBm)
  - 5200 MHz [40] (23.0 dBm)
  - 5220 MHz [44] (23.0 dBm)
  - 5240 MHz [48] (23.0 dBm)
  - 5260 MHz [52] (23.0 dBm) (radar detection)
  - 5280 MHz [56] (23.0 dBm) (radar detection)
  - 5300 MHz [60] (23.0 dBm) (radar detection)
  - 5320 MHz [64] (23.0 dBm) (radar detection)
  - 5500 MHz [100] (23.0 dBm) (radar detection)
  - 5520 MHz [104] (23.0 dBm) (radar detection)
  - 5540 MHz [108] (23.0 dBm) (radar detection)
  - 5560 MHz [112] (23.0 dBm) (radar detection)
  - 5580 MHz [116] (23.0 dBm) (radar detection)
  - 5600 MHz [120] (23.0 dBm) (radar detection)
  - 5620 MHz [124] (23.0 dBm) (radar detection)
  - 5640 MHz [128] (23.0 dBm) (radar detection)
  - 5660 MHz [132] (23.0 dBm) (radar detection)
  - 5680 MHz [136] (23.0 dBm) (radar detection)
  - 5700 MHz [140] (23.0 dBm) (radar detection)
  - 5745 MHz [149] (30.0 dBm)
  - 5765 MHz [153] (30.0 dBm)
  - 5785 MHz [157] (30.0 dBm)
  - 5805 MHz [161] (30.0 dBm)
  - 5825 MHz [165] (30.0 dBm) Supported commands:
- new_interface
- set_interface
- new_key
- start_ap
- new_station
- new_mpath
- set_mesh_config
- set_bss
- authenticate
- associate
- deauthenticate
- disassociate
- join_ibss
- join_mesh
- remain_on_channel
- set_tx_bitrate_mask
- frame
- frame_wait_cancel
- set_wiphy_netns
- set_channel
- set_wds_peer
- tdls_mgmt
- tdls_oper
- probe_client
- set_noack_map
- register_beacons
- start_p2p_device
- set_mcast_rate
- connect
- disconnect
- set_qos_map
- set_multicast_to_unicast software interface modes (can always be added):
- AP/VLAN
- monitor interface combinations are not supported HT Capability overrides:
- MCS: ff ff ff ff ff ff ff ff ff ff
- maximum A-MSDU length
- supported channel width
- short GI for 40 MHz
- max A-MPDU length exponent
- min MPDU start spacing Device supports TX status socket option. Device supports HT-IBSS. Device supports SAE with AUTHENTICATE command Device supports low priority scan. Device supports scan flush. Device supports AP scan. Device supports per-vif TX power setting Driver supports full state transitions for AP/GO clients Driver supports a userspace MPM Device supports configuring vdev MAC-addr on create. Device supports randomizing MAC-addr in scans. max # scan plans: 1 max scan plan interval: -1 max scan plan iterations: 0 Supported TX frame types:
- IBSS: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- managed: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- AP: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- AP/VLAN: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- mesh point: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- P2P-client: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- P2P-GO: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0
- P2P-device: 0x00 0x10 0x20 0x30 0x40 0x50 0x60 0x70 0x80 0x90 0xa0 0xb0 0xc0 0xd0 0xe0 0xf0 Supported RX frame types:
- IBSS: 0x40 0xb0 0xc0 0xd0
- managed: 0x40 0xb0 0xd0
- AP: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- AP/VLAN: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- mesh point: 0xb0 0xc0 0xd0
- P2P-client: 0x40 0xd0
- P2P-GO: 0x00 0x20 0x40 0xa0 0xb0 0xc0 0xd0
- P2P-device: 0x40 0xd0 Supported extended features:
[ FILS_STA ]: STA FILS (Fast Initial Link Setup)
[ CONTROL_PORT_OVER_NL80211 ]: control port over nl80211
[ TXQS ]: FQ-CoDel-enabled intermediate TXQs
[ SCAN_RANDOM_SN ]: use random sequence numbers in scans
[ SCAN_MIN_PREQ_CONTENT ]: use probe request with only rate IEs in scans
[ CAN_REPLACE_PTK0 ]: can safely replace PTK 0 when rekeying
[ CONTROL_PORT_NO_PREAUTH ]: disable pre-auth over nl80211 control port support
[ DEL_IBSS_STA ]: deletion of IBSS station support
[ SCAN_FREQ_KHZ ]: scan on kHz frequency support
[ CONTROL_PORT_OVER_NL80211_TX_STATUS ]: tx status for nl80211 control port support

fastoe / RTL8812BU

Is the TP Link Archer T4U V3 supports AP mode??? #15