Closed JustCauseWhyNot closed 5 days ago
can you paste the output of sensors
?
Despite zenpower being loaded it doesn't seem to show. I don't know if it's cause I'm using a zen4 cpu or not, but it uses the same kernel socket if my understanding is correct as k10temp which covers zen4.
Despite zenpower being loaded it doesn't seem to show. I don't know if it's cause I'm using a zen4 cpu or not, but it uses the same kernel socket if my understanding is correct as k10temp which covers zen4. sensors
nvme-pci-0d00 Adapter: PCI adapter Composite: +26.9°C (low = -0.1°C, high = +82.8°C) (crit = +83.8°C) Sensor 1: +19.9°C (low = -273.1°C, high = +65261.8°C) Sensor 2: +24.9°C (low = -273.1°C, high = +65261.8°C) nct6799-isa-0290 Adapter: ISA adapter in0: 1.05 V (min = +0.00 V, max = +1.74 V) in1: 1.83 V (min = +0.00 V, max = +0.00 V) ALARM in2: 3.42 V (min = +0.00 V, max = +0.00 V) ALARM in3: 3.30 V (min = +0.00 V, max = +0.00 V) ALARM in4: 1.67 V (min = +0.00 V, max = +0.00 V) ALARM in5: 1.05 V (min = +0.00 V, max = +0.00 V) in6: 1.47 V (min = +0.00 V, max = +0.00 V) ALARM in7: 3.42 V (min = +0.00 V, max = +0.00 V) ALARM in8: 3.25 V (min = +0.00 V, max = +0.00 V) ALARM in9: 1.81 V (min = +0.00 V, max = +0.00 V) ALARM in10: 1.30 V (min = +0.00 V, max = +0.00 V) ALARM in11: 1.12 V (min = +0.00 V, max = +0.00 V) ALARM in12: 1.02 V (min = +0.00 V, max = +0.00 V) ALARM in13: 896.00 mV (min = +0.00 V, max = +0.00 V) ALARM in14: 1.36 V (min = +0.00 V, max = +0.00 V) ALARM in15: 1.12 V (min = +0.00 V, max = +0.00 V) ALARM in16: 1.81 V (min = +0.00 V, max = +0.00 V) ALARM in17: 184.00 mV (min = +0.00 V, max = +0.00 V) fan1: 0 RPM (min = 0 RPM) fan2: 1066 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 1044 RPM (min = 0 RPM) fan5: 1498 RPM (min = 0 RPM) fan7: 1075 RPM (min = 0 RPM) SYSTIN: +19.0°C (high = +80.0°C, hyst = +75.0°C) (crit = +127.0°C) sensor = thermistor CPUTIN: +24.0°C (high = +80.0°C, hyst = +75.0°C) (crit = +80.0°C) sensor = thermistor AUXTIN0: +1.0°C (high = +127.0°C, hyst = +110.0°C) (crit = +0.0°C) sensor = thermistor AUXTIN1: +10.0°C (high = +80.0°C, hyst = +75.0°C) (crit = +80.0°C) sensor = thermistor AUXTIN2: +19.0°C (high = +80.0°C, hyst = +75.0°C) (crit = +80.0°C) sensor = thermistor AUXTIN3: +7.0°C (high = +80.0°C, hyst = +75.0°C) (crit = +100.0°C) sensor = thermistor SMBUSMASTER 0: +41.5°C (high = +80.0°C, hyst = +75.0°C) AUXTIN4: +23.0°C (high = +80.0°C, hyst = +75.0°C) (crit = +80.0°C) AUXTIN5: +113.0°C PCH_CHIP_CPU_MAX_TEMP: +0.0°C PCH_CHIP_TEMP: +0.0°C PCH_CPU_TEMP: +0.0°C TSI0_TEMP: +41.8°C intrusion0: ALARM intrusion1: ALARM beep_enable: disabled
use zenergy, not zenpower
Ok I'll try. I was just using zenergy since there was an already existing ebuild for it.
Reopen if this hasn't been resolved
I've not tried to resolve. I'll reopen if it fails after I finally install zenergy.
Describe the bug cpu_power is displaying 0W
List relevant hardware/software information
To Reproduce Steps to reproduce the behavior:
Expected behavior Wattage usage from cpu
Screenshots