Power toggle in top navigation missing options

ReinBentdal commented 2 years ago

Fluidd Version

1.19.0

Browser

Safari

Device

Laptop

Operating System

macOS

What happened

There is no option to turn on the navigation menu power toggle, the only option is none. Am I missing something or is it a bug? Just updated from 1.18.2.

What did you expect to happen

Expected there to be an option to turn it on, maybe a new config option which is missing due to upgrading?

How to reproduce

Might encounter the issue if upgrading from a previous fluid version

Additional information

No response

kerbilg commented 2 years ago

Hi, do you see an element like this?

ReinBentdal commented 2 years ago

I am currently in a house-moving process, might be able to check in a couple of days

ReinBentdal commented 2 years ago

i dont

matmen commented 2 years ago

Can you share your power device configuration (/ config files)?

ReinBentdal commented 2 years ago

not sure if I understand which files you mean. Could you elaborate?

ReinBentdal commented 2 years ago

not sure if I understand which files you mean. Could you elaborate?

matmen commented 2 years ago

Both your printer.cfg as well as moonraker.conf

ReinBentdal commented 2 years ago

printer.cfg

# This file contains common pin mappings for the BigTreeTech Octopus V1.
# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference

# after running "make", copy the generated "klipper/out/klipper.bin" file to a
# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.

# See docs/Config_Reference.md for a description of parameters.

## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config

[include macros.cfg]
[include fluidd.cfg]

[include stealthburner.cfg]

[include klicky/klicky-probe.cfg]

[mcu rpi]
serial: /tmp/klipper_host_mcu

[adxl345]
cs_pin: rpi:None

[resonance_tester]
accel_chip: adxl345
probe_points:
   125, 125, 20  # an example

#[input_shaper]
#shaper_freq_x: 58.6
#shaper_type_x: mzv
#shaper_freq_y: 45.0
#shaper_type_y: mzv

[mcu]
##  Obtain definition by "ls -l /dev/serial/by-id/" then unplug to verify
##--------------------------------------------------------------------
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_130047000350534E4E313020-if00
restart_method: command
##--------------------------------------------------------------------

[printer]
kinematics: corexy
max_velocity: 800
max_accel: 6000            
max_accel_to_decel: 6000
max_z_velocity: 20          #Max 15 for 12V TMC Drivers, can increase for 24V
max_z_accel: 350
square_corner_velocity: 5.0

#####################################################################
#   X/Y Stepper Settings
#####################################################################

##  B Stepper - Left
##  Connected to MOTOR_0
##  Endstop connected to DIAG_0
[stepper_x]
step_pin: PF13
dir_pin: PF12
enable_pin: !PF14
rotation_distance: 40
microsteps: 128
full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
endstop_pin: !PG6
position_min: 0
##--------------------------------------------------------------------

##  Uncomment below for 250mm build
position_endstop: 250
position_max: 250

##--------------------------------------------------------------------
homing_speed: 25   #Max 100
homing_retract_dist: 5
homing_positive_dir: true

##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_x]
uart_pin: PC4
interpolate: false
run_current: 0.8
sense_resistor: 0.110
#stealthchop_threshold: 999999

##  A Stepper - Right
##  Connected to MOTOR_1
##  Endstop connected to DIAG_1
[stepper_y]
step_pin: PG0
dir_pin: PG1
enable_pin: !PF15
rotation_distance: 40
microsteps: 128
full_steps_per_rotation:200  #set to 400 for 0.9 degree stepper
endstop_pin: !PG9
position_min: 5
##--------------------------------------------------------------------

##  Uncomment for 250mm build
position_endstop: 260
position_max: 260

##--------------------------------------------------------------------
homing_speed: 25  #Max 100
homing_retract_dist: 5
homing_positive_dir: true

##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_y]
uart_pin: PD11
interpolate: false
run_current: 0.8
sense_resistor: 0.110
#stealthchop_threshold: 999999

#####################################################################
#   Z Stepper Settings
#####################################################################

## Z0 Stepper - Front Left
##  Connected to MOTOR_2
##  Endstop connected to DIAG_2
[stepper_z]
step_pin: PF11
dir_pin: PG3
enable_pin: !PG5
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32
endstop_pin: PG10
##  Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
##  (+) value = endstop above Z0, (-) value = endstop below
##  Increasing position_endstop brings nozzle closer to the bed
##  After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
#position_endstop: 2
##--------------------------------------------------------------------

##  Uncomment below for 250mm build
position_max: 230

##  Uncomment below for 300mm build
#position_max: 280

##  Uncomment below for 350mm build
#position_max: 330

##--------------------------------------------------------------------
position_min: -5
homing_speed: 8
second_homing_speed: 3
homing_retract_dist: 3

##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z]
uart_pin: PC6
interpolate: false
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 999999

##  Z1 Stepper - Rear Left
##  Connected to MOTOR_3
[stepper_z1]
step_pin: PG4
dir_pin: !PC1
enable_pin: !PA0
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32

##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z1]
uart_pin: PC7
interpolate: false
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 999999

##  Z2 Stepper - Rear Right
##  Connected to MOTOR_4
[stepper_z2]
step_pin: PF9
dir_pin: PF10
enable_pin: !PG2
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32

##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z2]
uart_pin: PF2
interpolate: false
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 999999

##  Z3 Stepper - Front Right
##  Connected to MOTOR_5
[stepper_z3]
step_pin: PC13
dir_pin: !PF0
enable_pin: !PF1
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32

##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z3]
uart_pin: PE4
interpolate: false
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 999999

#####################################################################
#   Extruder
#####################################################################

##  Connected to MOTOR_6
##  Heater - HE0
##  Thermistor - T0
[extruder]
step_pin: PE2
dir_pin: !PE3
enable_pin: !PD4
##  Update value below when you perform extruder calibration
##  If you ask for 100mm of filament, but in reality it is 98mm:
##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
##  22.6789511 is a good starting point
rotation_distance: 22.6789511   #Bondtech 5mm Drive Gears
##  Update Gear Ratio depending on your Extruder Type
##  Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
##  Use 80:20 for M4, M3.1
gear_ratio: 50:10               #BMG Gear Ratio
microsteps: 32
full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.400
filament_diameter: 1.75
heater_pin: PA2
##  Validate the following thermistor type to make sure it is correct
##  See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
sensor_type: ATC Semitec 104GT-2
sensor_pin: PF4
min_temp: 10
max_temp: 270
max_power: 1.0
min_extrude_temp: 170
max_extrude_cross_section: 30
##  Try to keep pressure_advance below 1.0
pressure_advance: 0.06
##  Default is 0.040, leave stock
#pressure_advance_smooth_time: 0.040

##  E0 on MOTOR6
##  Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 extruder]
uart_pin: PE1
interpolate: false
run_current: 0.3
hold_current: 0.2
sense_resistor: 0.110
#stealthchop_threshold: 999999

#####################################################################
#   Bed Heater
#####################################################################

[heater_bed]
##  SSR Pin - HE1
##  Thermistor - TB
heater_pin: PA1
##  Validate the following thermistor type to make sure it is correct
##  See https://www.klipper3d.org/Config_Reference.html#common-thermistors for additional options
sensor_type: Generic 3950
sensor_pin: PF3
##  Adjust Max Power so your heater doesn't warp your bed. Rule of thumb is 0.4 watts / cm^2 .
max_power: 0.75
min_temp: 0
max_temp: 120
#control: pid
#pid_kp: 58.437
#pid_ki: 2.347
#pid_kd: 363.769

#####################################################################
#   Probe
#####################################################################

[probe]
##  Inductive Probe
##  This probe is not used for Z height, only Quad Gantry Leveling

## Select the probe port by type:
## For the PROBE port. Will not work with Diode. May need pull-up resistor from signal to 24V.
pin: ^PG15
## For the DIAG_7 port. NEEDS BAT85 DIODE! Change to !PG15 if probe is NO.
#pin: PG15
## For Octopus Pro PROBE port; NPN and PNP proximity switch types can be set by jumper
#pin: ~!PC5

#--------------------------------------------------------------------

x_offset: 0
y_offset: 25.0
z_offset: 0
speed: 10.0
samples: 3
samples_result: median
sample_retract_dist: 3.0
samples_tolerance: 0.006
samples_tolerance_retries: 3

#####################################################################
#   Fan Control
#####################################################################

[fan]
# 4-pin computer PWM exhaust fan - FAN5
pin: !PD15
# control: pid
# pid_Kp: 40
# pid_Ki: 0.2
# pid_Kd: 0.1
max_power: 1.0
# min_speed: 0
# max_speed: 1
# shutdown_speed: 0.0
kick_start_time: 0.5

# The official PC fan spec calls for 21-28kHz PWM frequency, but my Noctua at least was happy with the default 100Hz software PWM. So if your controller doesn't support hardware_pwm then try leaving these two lines out:
hardware_pwm: True
cycle_time: 0.0001666667 # 6 kHz

# OLD
##  Print Cooling Fan - FAN0
# pin: PA8
# kick_start_time: 0.5
##  Depending on your fan, you may need to increase this value
##  if your fan will not start. Can change cycle_time (increase)
##  if your fan is not able to slow down effectively
# off_below: 0.10

[heater_fan hotend_fan]
##  Hotend Fan - FAN1
pin: PE5
max_power: 1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
##  If you are experiencing back flow, you can reduce fan_speed
# fan_speed: 0.75

[multi_pin controller_fan_pins]
pins: PD12, PD13

[controller_fan controller_fan]
##  Controller fan - FAN2
pin: multi_pin:controller_fan_pins
# kick_start_time: 0.5
max_power: 1.0
fan_speed: 0.15

#hardware_pwm: True
cycle_time: 0.024 # 40 Hz

#heater: heater_bed, extruder
stepper: stepper_x, stepper_y, stepper_z, extruder

[delayed_gcode controller_fan_start]
initial_duration: 1
gcode: SET_FAN_SPEED FAN=controller_fan SPEED=0.9

#[heater_fan exhaust_fan]
##  Exhaust fan - FAN3
#pin: PD13
#max_power: 1.0
#shutdown_speed: 0.0
#kick_start_time: 5.0
#heater: heater_bed
#heater_temp: 60
#fan_speed: 1.0

#####################################################################
#   Thermals
#####################################################################
[temperature_sensor raspberry_pi]
sensor_type: temperature_host
max_temp: 100

[temperature_sensor MCU]
sensor_type: temperature_mcu
max_temp: 100

#[temperature_sensor chamber]
#sensor_type: HTU21D
#i2c_address:
#   Default is 64 (0x40).
#i2c_mcu: rpi
#i2c_bus: i2c.1
#i2c_speed: 100000
#   See the "common I2C settings" section for a description of the
#   above parameters.
#htu21d_hold_master:
#   If the sensor can hold the I2C buf while reading. If True no other
#   bus communication can be performed while reading is in progress.
#   Default is False.
#htu21d_resolution: TEMP14_HUM12
#   The resolution of temperature and humidity reading.
#   Valid values are:
#    'TEMP14_HUM12' -> 14bit for Temp and 12bit for humidity
#    'TEMP13_HUM10' -> 13bit for Temp and 10bit for humidity
#    'TEMP12_HUM08' -> 12bit for Temp and 08bit for humidity
#    'TEMP11_HUM11' -> 11bit for Temp and 11bit for humidity
#   Default is: "TEMP11_HUM11"
#htu21d_report_time:

#####################################################################
#   LED Control
#####################################################################

## Chamber Lighting - HE2 Connector (Optional)
#[output_pin caselight]
#pin: PB10
#pwm:true
#shutdown_value: 0
#value:1
#cycle_time: 0.01

#####################################################################
#   Homing and Gantry Adjustment Routines
#####################################################################

[idle_timeout]
timeout: 1800

#[safe_z_home]
##  XY Location of the Z Endstop Switch
##  Update -10,-10 to the XY coordinates of your endstop pin 
##  (such as 157,305) after going through Z Endstop Pin
##  Location Definition step.
#home_xy_position:187,260
#speed:100
#z_hop:10

[quad_gantry_level]
##  Use QUAD_GANTRY_LEVEL to level a gantry.
##  Min & Max gantry corners - measure from nozzle at MIN (0,0) and 
##  MAX (250, 250), (300,300), or (350,350) depending on your printer size
##  to respective belt positions

#--------------------------------------------------------------------
##  Gantry Corners for 250mm Build
gantry_corners:
   -60,-10
   310, 320
##  Probe points
points:
   25,25
   25,200
   225,200
   225,25

#--------------------------------------------------------------------
speed: 300
horizontal_move_z: 10
retries: 5
retry_tolerance: 0.0075
max_adjust: 10

[bed_mesh]
speed: 120
horizontal_move_z: 10
mesh_min: 35, 60
mesh_max: 225, 190
probe_count: 5, 3

########################################
# EXP1 / EXP2 (display) pins
########################################

[board_pins]
aliases:
    # EXP1 header
    EXP1_1=PE8, EXP1_2=PE7,
    EXP1_3=PE9, EXP1_4=PE10,
    EXP1_5=PE12, EXP1_6=PE13,    # Slot in the socket on this side
    EXP1_7=PE14, EXP1_8=PE15,
    EXP1_9=<GND>, EXP1_10=<5V>,

    # EXP2 header
    EXP2_1=PA6, EXP2_2=PA5,
    EXP2_3=PB1, EXP2_4=PA4,
    EXP2_5=PB2, EXP2_6=PA7,      # Slot in the socket on this side
    EXP2_7=PC15, EXP2_8=<RST>,
    EXP2_9=<GND>, EXP2_10=<5V>

#####################################################################
#   Displays
#####################################################################

##  Uncomment the display that you have

[display]
#  mini12864 LCD Display
lcd_type: uc1701
cs_pin: EXP1_3
a0_pin: EXP1_4
rst_pin: EXP1_5
encoder_pins: ^EXP2_5, ^EXP2_3
click_pin: ^!EXP1_2
contrast: 63
spi_software_miso_pin: EXP2_1
spi_software_mosi_pin: EXP2_6
spi_software_sclk_pin: EXP2_2

[neopixel btt_mini12864]
#  To control Neopixel RGB in mini12864 display
pin: EXP1_6
chain_count: 3
initial_RED: 0.0
initial_GREEN: 0.0
initial_BLUE: 0.0
color_order: RGB

#  Set RGB values on boot up for each Neopixel. 
#  Index 3 = display, Index 1 and 2 = Knob
[delayed_gcode setdisplayneopixel]
initial_duration: 1
gcode:
        SET_LED LED=btt_mini12864 RED=0 GREEN=0 BLUE=0 INDEX=1 TRANSMIT=0
        SET_LED LED=btt_mini12864 RED=0 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
        SET_LED LED=btt_mini12864 RED=0.2 GREEN=0.2 BLUE=0.2 INDEX=3 
#--------------------------------------------------------------------

#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 29.593
#*# pid_ki = 1.617
#*# pid_kd = 135.387
#*#
#*# [heater_bed]
#*# control = pid
#*# pid_kp = 40.695
#*# pid_ki = 1.833
#*# pid_kd = 225.859
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*#       6.073441, 6.093441, 6.098441, 6.093441, 6.093441
#*#       6.014691, 6.025941, 6.043441, 6.049691, 6.049691
#*#       6.045941, 6.063441, 6.065941, 6.054691, 6.065941
#*# tension = 0.2
#*# min_x = 35.0
#*# algo = lagrange
#*# y_count = 3
#*# mesh_y_pps = 2
#*# min_y = 60.0
#*# x_count = 5
#*# max_y = 190.0
#*# mesh_x_pps = 2
#*# max_x = 225.0
#*#
#*# [stepper_z]
#*# position_endstop = 2.578
#*#
#*# [input_shaper]
#*# shaper_type_x = mzv
#*# shaper_freq_x = 60.0
#*# shaper_type_y = 2hump_ei
#*# shaper_freq_y = 61.0

Moonraker.conf

[server]
host: 0.0.0.0
port: 7125
enable_debug_logging: False

[authorization]
force_logins: True
cors_domains:
  *.local
  *.lan
  *://app.fluidd.xyz

trusted_clients:
  **removed**

[file_manager]
config_path: ~/klipper_config
log_path: ~/klipper_logs

[data_store]
temperature_store_size: 600
gcode_store_size: 1000

# enables partial support of Octoprint API
[octoprint_compat]

# enables moonraker to track and store print history.
[history]

# this enables moonraker's update manager
[update_manager]
enable_auto_refresh: True

# this enabled fluidd updates
[update_manager client fluidd]
type: web
repo: cadriel/fluidd
path: ~/fluidd

matmen commented 2 years ago

Well, what device are you expecting to show up? I don't see any configured in your configs

ReinBentdal commented 2 years ago

Then it might be on me. I was looking for a way to turn on the button added in #736. Do I then have to add something manually to the configs?

matmen commented 2 years ago

This is intended as a power toggle for the printer (or any other moonraker power device, really). You will need to add a power device to your moonraker config for it to show up

ReinBentdal commented 2 years ago

i see, then it should be all good. Thanks!

fluidd-core / fluidd