Open Zicmu69 opened 3 years ago
Did u swap rx tx?
Also, connect SIGNAL GROUND from dji to fc gnd. It helps for some people.
What kind of buzzer signals u get? Could be no radio alarm.
/FC
On 7 Oct 2020, at 11:00, Zicmu69 notifications@github.com wrote:
Hello,
I've connected UART from Caddx Vista to RX1 and TX1 on my FC via connector. I've tried to connect Vista to UART3 also, but no effect. When I use advanced serial configuration in GUI and set DJI-MSP to UART coresponding to connected one- nothing happened either- besides some more option about DJI OSD comes out in GUI. Also when I plug in the battery with advanced serial configuration on- there are 3 buzzer singnals after standard boot sequence. Can you tell me how DJI- MSP should be configured and connected? My Custom OSD in goggles is turned on.
— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub https://github.com/flyduino/kiss-gui/issues/19, or unsubscribe https://github.com/notifications/unsubscribe-auth/AAQBCCTDDCXPBPR737Z7AVTSJQU4LANCNFSM4SHDL2EQ.
Yes, I did swap RX and TX. Buzzer.zip That is the signal. My radio is ON, and I'm able to arm the quad. I'm using CRSF. In advanced serial configuration default Serial 2 is receiver and serial 5 is VTX + ESC TLM is that correct for Fettec FC? Should I disable UART3 if it is not used?
I'll try to connect SIG GND... update in a minute.
its normal sound - gyro calibrated.
On 7 Oct 2020, at 11:12, Zicmu69 notifications@github.com wrote:
Yes, I did swap RX and TX. Buzzer.zip https://github.com/flyduino/kiss-gui/files/5339414/Buzzer.zip That is the signal. My radio is ON, and I'm able to arm the quad. I'm using CRSF. In advanced serial configuration default Serial 2 is receiver and serial 5 is VTX + ESC TLM is that correct for Fettec FC? Should I disable UART3 if it is not used?
I'll try to connect SIG GND... update in a minute.
— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/flyduino/kiss-gui/issues/19#issuecomment-704803689, or unsubscribe https://github.com/notifications/unsubscribe-auth/AAQBCCWH6OHEESIRY46OKFDSJQWILANCNFSM4SHDL2EQ.
Ground connected to FC so let's check...
Aaaaaaaaand done! Thank you Comander! You are the best! Can I turn off all unused UARTS? Is there any manual where you can see that TLM pad is UART 2 or something like that? I found Serial 1 and 3 in manual, but nowhere to find info about 2 and 5.
keep unused ports as default - kiss protocol. thats it. enjoy braza.
Cheers, Alex
On 7 Oct 2020, at 11:50, Zicmu69 notifications@github.com wrote:
Ground connected to FC so let's check...
Aaaaaaaaand done! Thank you Comander! You are the best! Can I turn off all unused UARTS? Is there any manual where you can see that TLM pad is UART 2 or something like that? I found Serial 1 and 3 in manual, but nowhere to find info about 2 and 5.
— You are receiving this because you commented. Reply to this email directly, view it on GitHub, or unsubscribe.
Hello! I have followed this and nothing, no OSD. 🫤
It's trash. Buy ultra. Full osd on everything like it should be
On Fri, Nov 17, 2023, 8:04 AM Malf20035 @.***> wrote:
Hello! I have followed this and nothing, no OSD. 🫤
— Reply to this email directly, view it on GitHub https://github.com/flyduino/kiss-gui/issues/19#issuecomment-1816387204, or unsubscribe https://github.com/notifications/unsubscribe-auth/AKDU7JWZIYEZFKIMXSYSESTYE5OETAVCNFSM4SHDL2E2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGYZTQNZSGA2A . You are receiving this because you are subscribed to this thread.Message ID: @.***>
thats really sums it up. ;)---Cheers,AlexOn 17 Nov 2023, at 14:14, krunked-fpv @.***> wrote: It's trash. Buy ultra. Full osd on everything like it should be
On Fri, Nov 17, 2023, 8:04 AM Malf20035 @.***> wrote:
Hello! I have followed this and nothing, no OSD. 🫤
—
Reply to this email directly, view it on GitHub
https://github.com/flyduino/kiss-gui/issues/19#issuecomment-1816387204,
or unsubscribe
.
You are receiving this because you are subscribed to this thread.Message
ID: @.***>
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you commented.Message ID: @.***>
😅 Soldered the osd disable jumpers and it works, kind of. At least I can see the voltage. It is on Fettec G4.
sorry to hear about that.. kiss-ultra.com is what you want. youve painted yourself into a corner using fettec. its too bad ,really. https://discord.gg/kissultra
On Fri, Nov 17, 2023 at 8:53 AM Malf20035 @.***> wrote:
😅 Soldered the osd disable jumpers and it works, kind of. At least I can see the voltage. It is on Fettec G4.
— Reply to this email directly, view it on GitHub https://github.com/flyduino/kiss-gui/issues/19#issuecomment-1816472097, or unsubscribe https://github.com/notifications/unsubscribe-auth/AKDU7JRMT3RBCNILYNFBTF3YE5T55AVCNFSM4SHDL2E2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGY2DOMRQHE3Q . You are receiving this because you commented.Message ID: @.***>
;)---Cheers,AlexOn 17 Nov 2023, at 14:53, Malf20035 @.***> wrote: 😅 Soldered the osd disable jumpers and it works, kind of. At least I can see the voltage. It is on Fettec G4.
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you commented.Message ID: @.***>
Thanks! An other fpv pilot I know is trying out Kiss Ultra soon. I just have bought the Fettec G4 just to try out, and I kind of like it. I will definitely buy a Kiss Ultra, but not now, my budget is limited.
Ultra is many orders of magnitude better. Sorry not sorry. You fucked up buying fettec. Once u realize that you will thank me.. they always do.
On Fri, Nov 17, 2023, 12:36 PM Malf20035 @.***> wrote:
Thanks! An other fpv pilot I know is trying out Kiss Ultra soon. I just have bought the Fettec G4 just to try out, and I kind of like it. I will definitely buy a Kiss Ultra, but not now, my budget is limited.
— Reply to this email directly, view it on GitHub https://github.com/flyduino/kiss-gui/issues/19#issuecomment-1816828411, or unsubscribe https://github.com/notifications/unsubscribe-auth/AKDU7JXWAE2K76NGQQCXUFDYE6ODTAVCNFSM4SHDL2E2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGY4DEOBUGEYQ . You are receiving this because you commented.Message ID: @.***>
totally agree with alex on this one. ---Cheers,AlexOn 17 Nov 2023, at 18:38, krunked-fpv @.***> wrote: Ultra is many orders of magnitude better. Sorry not sorry. You fucked up
buying fettec. Once u realize that you will thank me.. they always do.
On Fri, Nov 17, 2023, 12:36 PM Malf20035 @.***> wrote:
Thanks! An other fpv pilot I know is trying out Kiss Ultra soon. I just
have bought the Fettec G4 just to try out, and I kind of like it. I will
definitely buy a Kiss Ultra, but not now, my budget is limited.
—
Reply to this email directly, view it on GitHub
https://github.com/flyduino/kiss-gui/issues/19#issuecomment-1816828411,
or unsubscribe
.
You are receiving this because you commented.Message ID:
@.***>
—Reply to this email directly, view it on GitHub, or unsubscribe.You are receiving this because you commented.Message ID: @.***>
Hello,
I've connected UART from Caddx Vista to RX1 and TX1 on my FC via connector. I've tried to connect Vista to UART3 also, but no effect. When I use advanced serial configuration in GUI and set DJI-MSP to UART coresponding to connected one- nothing happened either- besides some more option about DJI OSD comes out in GUI. Also when I plug in the battery with advanced serial configuration on- there are 3 buzzer singnals after standard boot sequence. Can you tell me how DJI- MSP should be configured and connected? My Custom OSD in goggles is turned on.