search

flyduino / kiss-gui

Multiplatform standalone Kiss GUI
42 stars 7 forks source link

Kiss v1, 24a Race ESC not able to flash firmware #21

Open Com4nd3r opened 4 years ago

Com4nd3r commented 4 years ago

Was not able to flash ESC in the kiss-gui_2.0.27. Kiss FC v1 is on rc45y. After using the ESC Flasher TAB it tolde me "no response from FC!"

Com4nd3r commented 4 years ago

it worked..all good installed RC39b. but check rc45y and 24a ESC flash

fedorcomander commented 4 years ago

fixed in 46c on patreon

Cheers, Alex

On 19 Nov 2020, at 21:02, Com4nd3r notifications@github.com wrote:

 Was not able to flash ESC in the kiss-gui_2.0.27. Kiss FC v1 is on rc45y. After using the ESC Flasher TAB it tolde me "no response from FC!"

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub, or unsubscribe.

fedorcomander commented 4 years ago

workaround. flash 40o. then program esc. then back to 45y

Cheers, Alex

On 19 Nov 2020, at 21:02, Com4nd3r notifications@github.com wrote:

 Was not able to flash ESC in the kiss-gui_2.0.27. Kiss FC v1 is on rc45y. After using the ESC Flasher TAB it tolde me "no response from FC!"

— You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub, or unsubscribe.

Com4nd3r commented 4 years ago

Thank you, i will try that workaround. Patreon i dont have so i must hold on with the older FW i guess. :-( I found another strange thing with kiss fc v1. hope its ok i say it here under this topic. i installed rc45y (rc40o is same problem) and there is something wrong with the PID. If i arm the quad the motors run not smooth and they sound scratchy. This problem only happen when i raise the PID´s over ...round 4,8 and higher at P pitch roll and D over 15-18 and more like this. if i touch the throttle stick it vanisch. if i rearm same happen.. do you know about this problem? i remounted fc different types and switched motors..always same problem.. Now im at the point to think downgrade even lower like rc3X Fw.

Greetings!

fedorcomander commented 4 years ago

that could be because adaptive filter kicks in when you move stick a little.

On 20 Nov 2020, at 12:08, Com4nd3r notifications@github.com wrote:

Thank you, i will try that workaround. Patreon i dont have so i must hold on with the older FW i guess. :-( I found another strange thing with kiss fc v1. hope its ok i say it here under this topic. i installed rc45y (rc40o is same problem) and there is something wrong with the PID. If i arm the quad the motors run not smooth and they sound scratchy. This problem only happen when i raise the PID´s over ...round 4,8 and higher at P pitch roll and D over 15-18 and more like this. if i touch the throttle stick it vanisch. if i rearm same happen.. do you know about this problem? i remounted fc different types and switched motors..always same problem.. Now im at the point to think downgrade even lower like rc3X Fw.

Greetings!

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/flyduino/kiss-gui/issues/21#issuecomment-731104647, or unsubscribe https://github.com/notifications/unsubscribe-auth/AAQBCCQHZADMQBXIDHBOPXTSQZEZ3ANCNFSM4T33NBYQ.

Com4nd3r commented 4 years ago

i made a movie so you can see what the problem is. it sounds not good til i move the stick. https://www.youtube.com/watch?v=H0sRtskNcqw (Kiss v1 rc45y installed) would be good if the adaptive filter could be active as soon as you plug the lipo in.

fedorcomander commented 4 years ago

its like this since day one for a reason. just arm and fly.

Cheers, Alex

On 20 Nov 2020, at 17:30, Com4nd3r notifications@github.com wrote:

 i made a movie so you can see what the problem is. it sounds not good til i move the stick. https://www.youtube.com/watch?v=H0sRtskNcqw (Kiss v1 rc45y installed) would be good if the adaptive filter could be active as soon as you plug the lipo in.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub, or unsubscribe.

Com4nd3r commented 4 years ago

OK. Thank you for helping!

Padillaz commented 3 years ago

Was not able to flash 25A ESC in the kiss-gui_2.0.29. Tried the "work around" by flashing the FC with 40i then back to 46 with no luck. It may have something to do with the chrome extensions. After the flash attempt and power cycling the ESC list would show up without any information next to each motor. Also would not save after selecting to reverse motors 1 and 3.

Com4nd3r commented 3 years ago

Flash RC40o bro. than try flash esc.

Padillaz commented 3 years ago

Tried that again with RC40o. No luck. For some reason any time I try to update/flash the ESC it will not save. Going to try RC39b.

Padillaz commented 3 years ago

Took it apart and figured out I had the 6pin wire harness in the wrong slot. I'm now updated to KISSFCV2F7-1.3-RC46i on FC and 121a Beep on the ESC. Thanks for the help!