Version 0.2.1 in NanoVNA-F Does Not Work work with NanoVNASaver 0.3.7

[cache4pat]

Sadly, NanoVNA-F, updated to Version 0.2.1 Does Not Work work with NanoVNASaver 0.3.7.

When I start up NanoVNASaver it reports this error immediately. "NanoVNASaver.Version - ERROR - Unable to parse version: 0-2-1"

What are my options ?? I have also reported this to the NanoVNASaver section of GitHub

[dsiminiuk]

There is a specific version of NanoVNA saver for the -f Model. See the Files area.

[ https://groups.io/g/nanovna-f/files/PC%20Software/nanovna-saver-0.3.4-bh5hnu.exe | nanovna-saver-0.3.4-bh5hnu.exe ]

From: "cache4pat" notifications@github.com To: "flyoob/NanoVNA-F" NanoVNA-F@noreply.github.com Cc: "Subscribed" subscribed@noreply.github.com Sent: Thursday, September 24, 2020 7:36:22 PM Subject: [flyoob/NanoVNA-F] Version 0.2.1 in NanoVNA-F Does Not Work work with NanoVNASaver 0.3.7 (#20)

Sadly, NanoVNA-F, updated to Version 0.2.1 Does Not Work work with NanoVNASaver 0.3.7.

When I start up NanoVNASaver it reports this error immediately. "NanoVNASaver.Version - ERROR - Unable to parse version: 0-2-1"

What are my options ?? I have also reported this to the NanoVNASaver section of GitHub

— You are receiving this because you are subscribed to this thread. Reply to this email directly, [ https://github.com/flyoob/NanoVNA-F/issues/20 | view it on GitHub ] , or [ https://github.com/notifications/unsubscribe-auth/ABLS5CY2D4UEMXX6EBUPBLTSHPQYNANCNFSM4RY5SMWA | unsubscribe ] .

[cache4pat]

Hello Danny Siminiuk notifications@github.comFlyoob/Nanovna-F

Thank you for your guidance.

I changed to the OLDER 0.3.5 version and it seems not to spawn that 'parse error'.

I had tried to ignore the version 0.3.7 parse error, and run a few tests, which 'seemed' to create results; while the error message was on the 'console' screen. I repeated the same antenna measurements with version 0.3.5; and the graphic information seems similar; but the 'console screen' does not have the parsing error.

I am happy with that change to the recommended 0.3.5; but am curious about what the parsing issue was all about. Thank you again for your help.

Should I remove my 'error' report on github, or will you take care of that?

Cheers, Patrick

.

On Fri, Sep 25, 2020 at 3:31 PM Danny Siminiuk notifications@github.com wrote:

There is a specific version of NanoVNA saver for the -f Model. See the Files area.

[ https://groups.io/g/nanovna-f/files/PC%20Software/nanovna-saver-0.3.4-bh5hnu.exe | nanovna-saver-0.3.4-bh5hnu.exe ]

From: "cache4pat" notifications@github.com To: "flyoob/NanoVNA-F" NanoVNA-F@noreply.github.com Cc: "Subscribed" subscribed@noreply.github.com Sent: Thursday, September 24, 2020 7:36:22 PM Subject: [flyoob/NanoVNA-F] Version 0.2.1 in NanoVNA-F Does Not Work work with NanoVNASaver 0.3.7 (#20)

Sadly, NanoVNA-F, updated to Version 0.2.1 Does Not Work work with NanoVNASaver 0.3.7.

When I start up NanoVNASaver it reports this error immediately. "NanoVNASaver.Version - ERROR - Unable to parse version: 0-2-1"

What are my options ?? I have also reported this to the NanoVNASaver section of GitHub

— You are receiving this because you are subscribed to this thread. Reply to this email directly, [ https://github.com/flyoob/NanoVNA-F/issues/20 | view it on GitHub ] , or [

https://github.com/notifications/unsubscribe-auth/ABLS5CY2D4UEMXX6EBUPBLTSHPQYNANCNFSM4RY5SMWA | unsubscribe ] .

— You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub https://github.com/flyoob/NanoVNA-F/issues/20#issuecomment-699114422, or unsubscribe https://github.com/notifications/unsubscribe-auth/ARECWDEWA2OGNY7MPWXP2KDSHTVYTANCNFSM4RY5SMWA .

[cache4pat]

Thank you all. I can see here that all .the dots. have been connected; and my last question via groups.io made it here to github. A nice bit of magic 👍 And I note my TYPO error ... it was version 0.3.4 that I changed to; not 0.3.5,