search

free-pdk / easy-pdk-programmer-software

Easy PDK programmer for PADAUK microcontroller
https://free-pdk.github.io/
GNU General Public License v3.0
111 stars 37 forks source link

[PFC232] Verification failed during flashing #60

Open kaweksl opened 3 years ago

kaweksl commented 3 years ago

Hi, Thanks for adding PFC232 support Finally i got some time to play with this MCU and i run into some issue.

Describe the bug Getting verify failed error when flashing PFC232 And on latest development version calibration fails too.

./easypdkprog -n PFC232 write Examples/src/build/helloworld_2cores_pfc232.ihx -v
Searching programmer... found: /dev/ttyACM1
FREE-PDK EASY PROG - HW:1.2 SW:1.3 PROTO:1.5 (1.3-52-ge064f5d)
HWVAR:0 HWMOD:1
Erasing IC... done.
Blank check IC... done.
Writing IC (325 words)... done.
Verifiying IC... FPDK_ERROR: verify failed
./easypdkprog -n PFC232 write Examples/src/build/helloworld_2cores_pfc232.ihx -v --noverify
Searching programmer... found: /dev/ttyACM1
FREE-PDK EASY PROG - HW:1.2 SW:1.3 PROTO:1.5 (1.3-52-ge064f5d)
HWVAR:0 HWMOD:1
Erasing IC... done.
Blank check IC... done.
Writing IC (325 words)... done.
Calibrating IC
* IHRC SYSCLK=8000000Hz @ 5.00V ... calibration result: 0Hz (0x00)  out of range.
ERROR: Calibration failed

Desktop (please complete the following information):

Additional context I have also tried version with PROTO:1.4 (commit a5e3d29472bc41658f46588ef918998dff4aaabb), PFC232 calibrates with --noverify only on programmer with R6 mod and example code works.

./easypdkprog -n PFC232 write Examples/src/build/helloworld_2cores_pfc232.ihx -v --noverify
Searching programmer... found: /dev/ttyACM1
FREE-PDK EASY PROG - HW:1.2 SW:1.3 PROTO:1.4 (1.3-46-ga5e3d29)
HWVAR:0 HWMOD:1
Erasing IC... done.
Blank check IC... done.
Writing IC (325 words)... done.
Calibrating IC
* IHRC SYSCLK=8000000Hz @ 5.00V ... calibration result: 8002134Hz (0x6E)  done.

helloworld_2cores_pfc232 programmed on PROTO 1.4, HWMOD:1 runs ok on programmer with latest firmware.

/easypdkprog start -v
Searching programmer... found: /dev/ttyACM1
FREE-PDK EASY PROG - HW:1.2 SW:1.3 PROTO:1.5 (1.3-52-ge064f5d-dirty)
HWVAR:0 HWMOD:1
Running IC (5.00V)... IC started, press [Esc] to stop.
Connected @169611 baud
Press a key on the host computer to send some bits, corg2 will detect this and core1 will output a '2' for every 1 bit
Hello World!
222222222222222222222Hello World!
222222
freepdk commented 3 years ago

I tried it with 2 variants of the programer (HWMOD:0 / HWMOD:1 = R6 mod) and in both cases I can erase/write/calibrate/run the exact same example without any issues.

From your output it looks like erase is working.

--noverifywill not help you to program a chip. In case there is a verify error then the wrong content was read back after writing. Then almost 100% for sure the IC will not work (calibration needs a working program as well).

It would be interesting to read back the content of the IC after you get FPDK_ERROR: verify failed

./easypdkprog -n PFC232 read readback_helloworld_2cores_pfc232.ihx

BTW: I saw your "helloworld.ihx" is slightly bigger than mine (maybe you use older SDCC).

In order to see differences please attach your "helloworld_2cores_pfc232.ihx" and your "readback_helloworld_2cores_pfc232.ihx".

Skywalkerf34 commented 3 years ago

@freepdk

Hello again, now with software issues Got same problem with my fresh new programmer

software version is 1.3

d:\Users\FidL\Documents\eagle\easyPDKprog\easy-pdk-programmer-software-master\release1.3\EASYPDKPROG>easypdkprog --icname=PFS154 erase Erasing IC... done.

d:\Users\FidL\Documents\eagle\easyPDKprog\easy-pdk-programmer-software-master\release1.3\EASYPDKPROG>easypdkprog probe Probing IC... found. TYPE:FLASH RSP:0x1AA1 VPP=4.50 VDD=2.00 IC is supported: PFS154 ICID:0xAA1

d:\Users\FidL\Documents\eagle\easyPDKprog\easy-pdk-programmer-software-master\release1.3\EASYPDKPROG>easypdkprog --icname=PFS154 write helloworld_pfs154.ihx Erasing IC... done. Writing IC (184 words)... done. FPDK_ERROR: verify failed

same result using PFS173

d:\Users\FidL\Documents\eagle\easyPDKprog\easy-pdk-programmer-software-master\release1.3\EASYPDKPROG>easypdkprog --runvdd=4.0 start Running IC (4.00V)... IC started, press [Esc] to stop. => top LED (3) is shinning but nothing on serial...

freepdk commented 3 years ago

@Skywalkerf34

If VERIFY fails, then the IC is not programed properly and of course it can not run.

Most likely your problem is caused by long wires between programmer and IC and/or bad connection from IC to socket / ...

Could you do the suggested read out after writing (see previous post)? Then attach hex file you tried to write and the read back hex file.

Skywalkerf34 commented 3 years ago

@freepdk

look to show some instabilities with programmer and someting said "nothing found" again...

Here is the readback for PFS154

readback_helloworld.zip

freepdk commented 3 years ago

Your readback shows a complete empty IC. Not a single bit has been written.

=> VDD / VPP supply to IC seems unstable (long wires, bad soldering, bad contact to IC in socket, ...)

Skywalkerf34 commented 3 years ago

@freepdk I have 2 programmer that was looking to discover the MCU yesterday today only one 'find the chip easypdkprogtest give 1st one : Cd: 4.99 vpp: 4.88 (vref= 3.30) confirmed real on pin 2nd one : Cd: 4.91 vpp: 4.58 (vref= 3.30)

The first one cannot discover the MCU anymore :-( the second one give the result I already send but time to time see also not able to rediscover the mcu

Should I buy a new socket adapter?

freepdk commented 3 years ago

VPP 4.58 seems a bit low, 4.88 is on the edge. Do you measure the values with the IC connected?

Skywalkerf34 commented 3 years ago

@freepdk

No as long as it is said not drive test with mcu on the programmer..... Should I ?

freepdk commented 3 years ago

@Skywalkerf34 No you should not. Then like I said, VPP 4.58 seems a bit low, 4.88 is on the edge.

Time to measure some things on PCB. => start easypdkprog test and measure + write down all pins from opamp. I will do same later and we can compare.

Skywalkerf34 commented 3 years ago

@freepdk

here is programmer "1" that cannot detect anymore pin 1 = 4.99 pin 2 =2.51 pin 3 =2.51 pin 4 =- 2.76 pin 5 = 1.188 pin 6 = 1.188 pin 7 = 5.01 pin 8 = 7.57

programmer "2" that detect but fail programming pin 1 = 4.99 pin 2 =2.51 pin 3 =2.51 pin 4 =- 2.79 pin 5 = 1.185 pin 6 = 1.185 pin 7 = 4.62 pin 8 = 7.26

Please note I am using same chip on same adapter than I just unplug from one programmer to the second one

freepdk commented 3 years ago

I will do some measurements (all over the board) later and provide info.

What I can immediately see: Voltage on pin 8 on both devices is much to low. This is the feed from the DC-DC booster and should have >13V.

=> check values of R1 / R5 => check soldering of D1 => check R24 / C13

Skywalkerf34 commented 3 years ago

@freepdk thevalue and soldering a correct, I check output voltage at U6 between D1 and C4 and the value here is only prog 1 8.91v prog 2 8.46v

The coil I am using is maybe not good enough ? ( cannot get the one on BOM I use CD43 6.8UH LIKE THIS ONE /https://inductor.com/product-spec/cd43.pdf

freepdk commented 3 years ago

@Skywalkerf34 Since it looks like you still have a hardware problem, let's continue in the hardware project repo: https://github.com/free-pdk/easy-pdk-programmer-hardware/issues/23

kaweksl commented 1 year ago

Hi, sorry for not responding but i was busy

So i had to create new environment, currently i'm using 

FREE-PDK EASY PROG - HW:1.2 SW:1.3 PROTO:1.5 (1.3-62-g38968a3)
HWVAR:0 HWMOD:0

i had to use commit 38968a32222e2d7c19f5b1be41db2a49a4437e3a as with newer versions i have issues (HWMOD not detecting, can't write ihx from exmaples ) .

I still have same issue with verification.

I'm attaching zip with 3 files: readout after erasing chip, original ihx that has beed written and readout after writing original ihx PFC232_verification_fail_files.zip

after writing example code with disabled verification, calibration works and uC seems to work ( using easypdkprog start )

UPDATE: Looks like i'm getting some corruption at writing. After writing to chip i'm reading same thing every time i read. but readout changes between writes, in different locations.

kaweksl commented 1 year ago

Seams like i might actually got some bad chips as some flash without issues. EDIT:

With "faulty" chips i have tried to flash them with --noerase and --noblank repeatedly and sometimes it passes verification.

freepdk commented 1 year ago

Seams like i might actually got some bad chips as some flash without issues. EDIT:

With "faulty" chips i have tried to flash them with --noerase and --noblank repeatedly and sometimes it passes verification.

Seems like a voltage / timing issue. Most likely it can be fixed with a more robust flashing implementation.