Can't connect to Wi-Fi

[juan22a91]

Hi. I have been struggling with this hack since I tried to go back to original firmware. When I installed it first, everything worked fine. I was able to get the RTSP streaming without any problems. But after I decided to go back to orinal firmware, I can´t connect to Wi-Fi and it sends after some time the Wi-Fi password error, even if I know the password is OK and double checked it.

After that, I tried to go back again to the RTSP hack and I was not able to connect to Wi.Fi either. The LED starts blinking orange when flashing the firmware, then it flashes blue when finding Wi-Fi connection, it stays blue for a few seconds and then it starts blinking orange again.

In the log file I found something related to the ra0 interface.

Help please

[hyptechdev2015]

@juan22a91 please share your log files

[juan22a91]

hi @hyptechdev2015 here is my log file

Starting to log... Hardware version informations : hwplatform=2 Software version informations : [sys] version=1.8.5.1M_201512011815 [kernel] version=3-0.8 provider=18e devtype=18e Firmware letter is : 'M' The RTSP server binary version which will be used is the 'M' The HTTP server binary version which will be used is the 'M' Check for some files size... -rwxr-xr-x 1 root root 144885 Oct 4 2016 /home/hd1/test/http/serverJ -rwxr-xr-x 1 root root 144912 Oct 4 2016 /home/hd1/test/http/serverM -rwxr-xr-x 1 root root 121932 Oct 4 2016 /home/hd1/test/rtspsvrI -rwxr-xr-x 1 root root 39572 Oct 4 2016 /home/hd1/test/rtspsvrK -rwxr-xr-x 1 root root 39580 Oct 4 2016 /home/hd1/test/rtspsvrM The blue led is currently blinking Debug mode = no Check for wifi configuration file...* /home/wpa_supplicant.conf Start wifi configuration... Status for wifi configuration=255 (0 is ok) Wifi configuration answer: Successfully initialized wpa_supplicant rfkill: Cannot open RFKILL control device Could not set interface ra0 flags (UP): Operation not permitted WEXT: Could not set interface 'ra0' UP ra0: Failed to initialize driver interface Do network configuration 1/2 (ip and gateway) Done Configuration is : lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

Do network configuration 2/2 (DNS) Done Get time from a NTP server... But first, test the NTP server '0.uk.pool.ntp.org': Previous datetime is Wed Dec 31 17:00:24 GMT 1969 Done New datetime is Wed Dec 31 17:00:25 GMT 1969 Start blue led on Start ftp server... Check for ftp process : 1227 root 1716 S tcpsvd -vE 0.0.0.0 21 ftpd -w / Start http server : serverM... Check for http server process : 1254 root 1408 S ./serverM 80 Start rtsp server : rtspsvrM... Check for rtsp process : 1318 root 2660 S < ./rtspsvrM Processes after startup : PID USER VSZ STAT COMMAND 1 root 1708 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW [rcu_kthread] 7 root 0 SW< [khelper] 8 root 0 SW [kworker/u:1] 143 root 0 SW [sync_supers] 145 root 0 SW [bdi-default] 146 root 0 SW< [kintegrityd] 148 root 0 SW< [kblockd] 161 root 0 SW [khubd] 174 root 0 SW< [cfg80211] 175 root 0 SW [kworker/0:1] 257 root 0 SW< [rpciod] 260 root 0 SW [kswapd0] 314 root 0 SW [fsnotify_mark] 322 root 0 SW< [nfsiod] 331 root 0 SW< [crypto] 405 root 0 SW [mtdblock0] 410 root 0 SW [mtdblock1] 415 root 0 SW [mtdblock2] 420 root 0 SW [mtdblock3] 425 root 0 SW [mtdblock4] 430 root 0 SW [mtdblock5] 435 root 0 SW [mtdblock6] 438 root 0 SW [romblock0] 441 root 0 SW [romblock1] 444 root 0 SW [romblock2] 447 root 0 SW [romblock3] 450 root 0 SW [romblock4] 453 root 0 SW [romblock5] 456 root 0 SW [romblock6] 591 root 0 SW< [kpsmoused] 600 root 0 SW [kworker/u:2] 616 root 0 SW [mmcqd/0] 623 root 0 SWN [jffs2_gcd_mtd4] 624 root 1712 S /bin/sh /etc/init.d/rcS 636 root 872 S < udevd --daemon 642 root 1704 S /bin/sh /etc/init.d/S80network 656 root 0 SWN [jffs2_gcd_mtd5] 657 root 1708 S /bin/sh ./init.sh 664 root 0 SW [flush-mtd-unmap] 675 root 1712 S /bin/sh /home/hd1/test/equip_test.sh 677 root 0 SW [flush-179:0] 682 root 1704 S telnetd 686 root 984 S /home/log_server 947 root 0 SW [hidog] 985 root 1164 S ./peripheral 986 root 1144 S < ./dispatch 987 root 1064 S ./exnet 1227 root 1716 S tcpsvd -vE 0.0.0.0 21 ftpd -w / 1254 root 1408 S ./serverM 80 1272 root 3360 S ./record_event 1273 root 14728 S ./mp4record 60 1302 root 1716 S /usr/sbin/crond -b 1312 root 904 S /home/led_ctl -boff -yfast 1313 root 97496 S ./rmm 1318 root 27252 S N ./rtspsvrM 1435 root 1708 R ps Storage status : Filesystem Size Used Available Use% Mounted on /dev/root 3.5M 3.4M 88.0K 98% / tmpfs 17.2M 16.0K 17.2M 0% /dev /dev/mtdblock5 8.9M 8.0M 916.0K 90% /home tmpfs 32.0M 40.0K 32.0M 0% /tmp /dev/hd1 7.4G 9.4M 7.4G 0% /tmp/hd1 tmpfs 512.0K 16.0K 496.0K 3% /home/mmap_tmpfs tmpfs 16.0M 0 16.0M 0% /home/tmpfs tmpfs 16.0M 3.0M 13.0M 19% /home/jrview /dev/hd1 7.4G 9.4M 7.4G 0% /tmp/hd1/test/http/record

[juan22a91]

And here is the log file for the original firmware (1.8.7.0A_201702081101)

[][12/31/17:0:6:246]: fopen in file fail! [][12/31/17:0:6:482]: decrypt file fail! [/home/rmm /tmp/au][12/31/17:0:8:562]: rmm_init_mpp ok! [/home/rmm /tmp/au][12/31/17:0:8:704]: start do HI_MPI_AI_GetVqeAttr [/home/rmm /tmp/au][12/31/17:0:8:728]: ai init ok! [/home/rmm /tmp/au][12/31/17:0:8:729]: rmm_init_ai ok! [/home/rmm /tmp/au][12/31/17:0:8:733]: rmm_init_adec init ok! [/home/rmm /tmp/au][12/31/17:0:8:734]: rmm_init_adec ok! [/home/rmm /tmp/au][12/31/17:0:8:907]: ao init ok! [/home/rmm /tmp/au][12/31/17:0:8:936]: rmm_init_ao ok!

[/home/rmm /tmp/au][12/31/17:0:11:702]: send_ao_beep: read file /tmp/audio/welcome.g726 not equal u32ReadLen(56) [/home/rmm /tmp/au][12/31/17:0:12:897]: rmm_init_mpp ok! [/home/rmm /tmp/au][12/31/17:0:13:66]: start do HI_MPI_AI_GetVqeAttr [/home/rmm /tmp/au][12/31/17:0:13:67]: ai init ok! [/home/rmm /tmp/au][12/31/17:0:13:67]: rmm_init_ai ok! [/home/rmm /tmp/au][12/31/17:0:13:68]: rmm_init_adec init ok! [/home/rmm /tmp/au][12/31/17:0:13:68]: rmm_init_adec ok! [/home/rmm /tmp/au][12/31/17:0:13:224]: ao init ok! [/home/rmm /tmp/au][12/31/17:0:13:252]: rmm_init_ao ok!

[/home/rmm /tmp/au][12/31/17:0:15:721]: send_ao_beep: read file /tmp/audio/start_wait.g726 not equal u32ReadLen(48) [/home/detect_ver][12/31/17:0:23:385]: get_board_ver, [ hwplatform=2 $
, 2 ] [/home/detect_ver][12/31/17:0:23:547]: start_rtc, [ hisi rtc ] [/home/detect_ver][12/31/17:0:23:604]: start_rtc ok.

[./dispatch][12/31/17:0:23:877]: cmd: renice -n -5 -p 1013 ok![./dispatch][12/31/17:0:24:484]: GetUiCfgFromFile success[./dispatch][12/31/17:0:24:485]: DISPATCH_init: language is 0, zkIndex 0, /etc/gb2312.zk [./dispatch][12/31/17:0:24:512]: DISPATCH_init: change to /etc/gb2312.zk ok! [./dispatch][12/31/17:0:24:513]: DISPATCH_init: test_result_file(10000) [./dispatch][12/31/17:0:24:513]: DISPATCH_init: GetVersionFromFile ok![./dispatch][12/31/17:0:24:678]: DISPATCH_init: do_reset sn_string(2498KMJRKW7LPJTSHV111ApklgPpeBUS4jVx2Hbe3ef4180d754586f2fadb61fffc4d52) gpmmapinfo->sn(be52e675a2c3b59afb738b535374f9e6) bind_timeout(1800) [./dispatch][12/31/17:0:24:690]: Dispatch MsgHandle start [./rmm][12/31/17:0:25:8]: check PO3100K _RockGetSensorTypeline_645data:0xff_ [./rmm][12/31/17:0:25:335]: check MT9M034_DATA___RockGetSensorTypeline660_data:0xffff_ [./rmm][12/31/17:0:25:335]: check OV_PIDHDATARockGetSensorTypeline679_data:0xff___ [./rmm][12/31/17:0:25:336]: check OV9732 RockGetSensorTypeline759_data:0x97___ [./rmm][12/31/17:0:25:336]: rmm_init_mpp ok! [./rmm][12/31/17:0:25:337]: start do HI_MPI_AI_GetVqeAttr [./rmm][12/31/17:0:25:395]: ai init ok! [./rmm][12/31/17:0:25:396]: rmm_init_ai ok! [./rmm][12/31/17:0:25:831]: rmm_init_aenc init ok! [./rmm][12/31/17:0:25:832]: rmm_init_aenc ok! [./rmm][12/31/17:0:25:863]: rmm_init_adec init ok! [./rmm][12/31/17:0:25:873]: rmm_init_adec ok! [./rmm][12/31/17:0:26:76]: ao init ok! [./rmm][12/31/17:0:26:77]: rmm_init_ao ok! [./rmm][12/31/17:0:26:78]: start do HI_MPI_AI_GetVqeAttr [./rmm][12/31/17:0:26:252]: system call back libsns_ov9732720p.so____ [./rmm][12/31/17:0:26:350]: ____come [ Rock_COMM_ISP_InitAE ]___ [./rmm][12/31/17:0:26:352]: _Gamma test for table 2__ [./rmm][12/31/17:0:26:353]: set auto WB [./rmm][12/31/17:0:26:355]: rmm_init_isp ok! [./rmm][12/31/17:0:26:458]: rmm_init_vi ok! [./rmm][12/31/17:0:26:468]: _VpssChn = 3, stVpssExtChnAttr.u32Width = 640, stVpssExtChnAttr.u32Height = 360 __ [./rmm][12/31/17:0:26:469]: _VpssChn = 6, stVpssExtChnAttr.u32Width = 320, stVpssExtChnAttr.u32Height = 240 __ [./rmm][12/31/17:0:26:470]: rmm_init_vpss ok! [./rmm][12/31/17:0:26:471]: frame rate=20 20 700 40 [./rmm][12/31/17:0:26:475]: ---------Rock_COMM_VENC_BindVpss VencGrp = 0, VpssGrp = 0, VpssChn = 0 [./rmm][12/31/17:0:26:476]: rc set success! venc(0) [./rmm][12/31/17:0:26:478]: frame rate=20 20 230 40 [./rmm][12/31/17:0:26:480]: ---------Rock_COMM_VENC_BindVpss VencGrp = 1, VpssGrp = 0, VpssChn = 3 [./rmm][12/31/17:0:26:481]: rc set success! venc(1) [./rmm][12/31/17:0:26:547]: rmm_init_venc ok! [./rmm][12/31/17:0:26:548]: HI_MPI_ISP_GetAEAttr type=0; exp time=65535 u32SystemGainMax(1) 36505 1024 4095 1024 4096 [./rmm][12/31/17:0:26:550]: set Rock_COMM_ISP_SetDRC 30 [./rmm][12/31/17:0:26:551]: ____stSharpenAttr.u8StrengthTarget = 140__ [./rmm][12/31/17:0:26:553]: ____Rock_COMM_ISPSetDenoise____ [./rmm][12/31/17:0:26:555]: u8ThreshTarget(21) u8ThreshMax(84) noiseTarget(0) [./rmm][12/31/17:0:26:562]: HI_MPI_VI_GetFrame err, vi chn 0 a008800d [./rmm][12/31/17:0:26:566]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:26:612]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:27:59]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:27:260]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:27:546]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:28:24]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:28:310]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:28:564]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:28:810]: get_data_frame width =352 height =192 [./rmm][12/31/17:0:28:849]: send_ao_beep: read file /tmp/audio/wait.g726 failed u32ReadLen(0) [./rmm][12/31/17:0:29:249]: get_data_frame width =352 height =192 ... ... ... [./rmm][12/31/17:1:46:244]: decoded QR-Code symbol "b=USnXbreLpoOdhMvi&s=Sk1DX0hPTUU=&p=UkwrKGFYDgF5" [./rmm][12/31/17:1:46:245]: trans_json info=b=USnXbreLpoOdhMvi&s=Sk1DX0hPTUU=&p=UkwrKGFYDgF5;key=&p= [./rmm][12/31/17:1:46:246]: trans_json result=UkwrKGFYDgF5 [./rmm][12/31/17:1:46:247]: trans_json info=b=USnXbreLpoOdhMvi&s=Sk1DX0hPTUU=&p=UkwrKGFYDgF5;key=&s= [./rmm][12/31/17:1:46:248]: trans_json result=Sk1DX0hPTUU= [./rmm][12/31/17:1:46:266]: trans_json info=b=USnXbreLpoOdhMvi&s=Sk1DX0hPTUU=&p=UkwrKGFYDgF5;key=b= [./rmm][12/31/17:1:46:268]: trans_json result=USnXbreLpoOdhMvi [./rmm][12/31/17:1:46:431]: rmm got /tmp/got_wpa ssid(JMC_HOME) pwd(juan22a91) bind(USnXbreLpoOdhMvi)

[./rmm][12/31/17:1:49:302]: send_ao_beep: read file /tmp/audio/scanok.g726 not equal u32ReadLen(16) [./rmm][12/31/17:1:52:243]: send_ao_beep: read file /tmp/audio/connectting.g726 not equal u32ReadLen(72) [/home/monitor_dum][12/31/17:3:32:129]: password is timeout [./rmm][12/31/17:3:32:748]: get_data_frame width =352 height =192 [./rmm][12/31/17:3:32:843]: get_data_frame width =352 height =192 [./rmm][12/31/17:3:33:131]: get_data_frame width =352 height =192 [./rmm][12/31/17:3:33:318]: get_data_frame width =352 height =192

[RiRomain]

I have the same problem, I tried multiple wifi access point, it just cannot connect anymore...