issues
search
fwachsmuth
/
rooDialino
A little AVR project to allow the rooDial to control the volume level of an amp or DAC by sending IR signals
0
stars
0
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
Consolidate transitionTo() functions
#32
fwachsmuth
opened
2 years ago
0
Add timeout in Learning Functions
#31
fwachsmuth
opened
2 years ago
0
Compare CHANGE vs RISING control speed
#30
fwachsmuth
closed
2 years ago
0
ISR events get queued up
#29
fwachsmuth
closed
2 years ago
0
Cannot turn IR Relay off while IR Pulses are being sent
#28
fwachsmuth
closed
2 years ago
1
Dial Events are queued when the Relay is off, and replayed when the Relay goes on again
#27
fwachsmuth
closed
2 years ago
0
Test if 5 ms delay between commands is optimal for all receivers
#26
fwachsmuth
opened
2 years ago
0
Add SPI Debugging
#25
fwachsmuth
opened
2 years ago
0
Handle the proposed serial commands
#24
fwachsmuth
opened
2 years ago
0
Reflect Sending on red/green LEDs
#23
fwachsmuth
closed
2 years ago
0
Test SEND_PWM_BY_TIMER on a 8 MHz Arduino
#22
fwachsmuth
opened
2 years ago
1
Measure Max current of 4 IR LEDs
#21
fwachsmuth
opened
2 years ago
0
prepare for programmability (upgradeability) via raspi avrdude and bit-banging
#20
fwachsmuth
opened
2 years ago
0
consider allowing to learn multiple IR commands per relay state
#19
fwachsmuth
opened
2 years ago
0
Consider 2 more commands: explicit on/off for the relay (vs toggle)
#18
fwachsmuth
opened
2 years ago
0
Use the actually learned codes
#17
fwachsmuth
closed
2 years ago
0
After Noise was received, subsequent IR-Learn Sessions sem to inherit noise from some queue
#16
fwachsmuth
closed
2 years ago
0
Solve D9-Pin vs IR Toggle Priority Issue
#15
fwachsmuth
opened
2 years ago
1
Do not accept UNKNOWN Protocol when learning IR
#14
fwachsmuth
closed
2 years ago
0
Short Bttn Push after Reset enters Settings Mode
#13
fwachsmuth
closed
2 years ago
0
Fix learnIRCode() to learn multiple things
#12
fwachsmuth
closed
2 years ago
0
Handle empty EEPROM (bootstrapping)
#11
fwachsmuth
closed
2 years ago
0
Create function to disable/reenable the IR emitter
#10
fwachsmuth
closed
2 years ago
0
save codes to EEPROM
#9
fwachsmuth
closed
2 years ago
0
read codes from EEPROM
#8
fwachsmuth
closed
2 years ago
0
Consider to support an "EnableRelay" Pin too
#7
fwachsmuth
closed
2 years ago
1
Allow On/Off of the device via IR as well
#6
fwachsmuth
closed
2 years ago
0
Prepare for "rapid firing until pulsing stops" approach
#5
fwachsmuth
closed
2 years ago
0
Draw the schematics
#4
fwachsmuth
closed
2 years ago
0
Add Code Learning Ability
#3
fwachsmuth
closed
2 years ago
0
Add On/Off Switch and State LED
#2
fwachsmuth
closed
2 years ago
0
Omit use of delays
#1
fwachsmuth
opened
2 years ago
0