Open gitxmax opened 5 years ago
Hello,
Thank you for feedback!
Do you mean service the systemd .service
? create_ap
had it and a .conf
file to work with. I deleted it to make the job simpler.
However you can write your own .service
file with arguments in ExecStart=
.
This is needed right now! Thank you so much!
This is what I'm working on, but I can't get the router to launch in a usable state automatically on boot using any of the three methods that follow
It will launch and broadcast an ap, but nothing will connect to it.
If I run this from cli it works as expected $ sudo ./lnxrouter --random-mac --ap wlan0 netgear0 -p testpass -c 3
If I try to set it as a systemd service things look good but nothing can connect to the ap (worth noting that starting the service manually after boot produces no change, enabling, disabling, stopping / starting, etc.. )
$ sudo systemctl status router.service router.service - linux-router Loaded: loaded (/etc/systemd/system/router.service; disabled; vendor preset: enabled) Active: active (running) since Sun 2021-03-07 22:19:40 UTC; 2s ago Main PID: 3091 (lnxrouter) Tasks: 7 (limit: 4915) CGroup: /system.slice/router.service ββ3091 /bin/bash /home/ubuntu/Downloads/linux-router-master/lnxrouter --ap wlan0 netgear0 ββ3202 /bin/bash /home/ubuntu/Downloads/linux-router-master/lnxrouter --ap wlan0 netgear0 ββ3205 sleep 2 ββ3206 hostapd -P /dev/shm/lnxrouter_tmp/lnxrouter.wlan0.conf.3u7/hostapd.pid /dev/shm/lnxrouter_tmp/lnxrouter.wlx984> ββ3207 /bin/bash /home/ubuntu/Downloads/linux-router-master/lnxrouter --ap wlan0 netgear0 ββ3208 sleep 3 ββ3209 sleep 10 Mar 07 22:19:40 ubuntu linux-router[3091]: Use random LAN IPv4 address 192.168.247.1 Mar 07 22:19:40 ubuntu linux-router[3091]: WARN: Wifi is not protected by password Mar 07 22:19:40 ubuntu linux-router[3091]: Set wlan0 unmanaged by NetworkManager Mar 07 22:19:41 ubuntu linux-router[3091]: haveged_watchdog PID: 3202 Mar 07 22:19:41 ubuntu linux-router[3091]: Starting hostapd Mar 07 22:19:41 ubuntu linux-router[3091]: hostapd PID: 3206 Mar 07 22:19:41 ubuntu linux-router[3206]: Configuration file: /dev/shm/lnxrouter_tmp/lnxrouter.wlan0.conf.3u7/hostapd.conf Mar 07 22:19:42 ubuntu linux-router[3206]: Using interface wlan0 with hwaddr 98:48:72:da:de:ba and ssid "netgear0" Mar 07 22:19:42 ubuntu linux-router[3206]: wlan0: interface state UNINITIALIZED->ENABLED Mar 07 22:19:42 ubuntu linux-router[3206]: wlan0: AP-ENABLED
I've tried a number of changes in the .service file but there has been no change. Referanced the create-ap .service file too. I can't say I've tried a conclusive set of params, but .service is where I've spent most of my time. Worth noting is I've tried these w/o auth, channel, and random-mac params. no change
$sudo nano router.service [Unit] Description=linux-router After=network.target [Service] Type=simple ExecStart=/home/ubuntu/Downloads/linux-router-master/lnxrouter --ap wlan0 netgear0 KillSignal=SIGINT Restart=always RestartSec=10 StandardOutput=syslog StandardError=syslog SyslogIdentifier=linux-router [Install] WantedBy=multi-user.target
I've tried rc.local, I'm sure I'm doing something wrong here because it won't launch/broadcast at all. It is chmod +x
/home/ubuntu/Downloads/linux-router-master/lnxrouter --random-mac --ap wlan0 netgear0 -p testpass -c 3 & exit 0
I've also tried starting it with $ gnome-session-properties
using the same command $ sudo ./lnxrouter --random-mac --ap wlan0 netgear0 -p testpass -c 3
Still results in a broadcast that I can't connect to. Tried several things including cell phones, computers, and an amazon fire stick (lol)
its running on a raspi / ubuntu 20.10 server
It may be worth noting that I am using two seperate interfaces for wifi. internal is recieving, usb is broadcasting
Any idea what I may be doing wrong here?
@eschwelgin Is that all log? Didn't see iptables and dnsmasq.
ββ3206 hostapd -P /dev/shm/lnxrouter_tmp/lnxrouter.wlx984827adde1a.conf.3u7/hostapd.pid /dev/shm/lnxrouter_tmp/lnxrouter.wlx984>
Mar 07 22:19:41 ubuntu linux-router[3091]: hostapd PID: 3206 Mar 07 22:19:41 ubuntu linux-router[3206]: Configuration file: /dev/shm/lnxrouter_tmp/lnxrouter.wlan0.conf.3u7/hostapd.conf
Why different configuration folder name? lnxrouter.wlan0.conf.3u7
and lnxrouter.wlx984827adde1a.conf.3u7
You chould try adding iptables.service and networkmanager.service as dependency. Try add a 2-minutes delay before calling lnxrouter
to to have system boot completely
I've tried rc.local, I'm sure I'm doing something wrong here because it won't launch/broadcast at all. It is chmod +x
!/bin/sh -e -p
/home/ubuntu/Downloads/linux-router-master/lnxrouter --random-mac --ap wlan0 netgear0 -p testpass -c 3 & exit 0
If use script, your script should be something like
sleep 120 # try a long enough delay
/home/ubuntu/Downloads/linux-router-master/lnxrouter --random-mac --ap wlan0 netgear0 -p testpass -c 3 &
sleep 2 # this sleep is must
disown -a # must !
sleep 2 # this sleep is must
exit 0 # then you can exit
@garywill
I cleaned up my op to make some of the outputs a bit clearer, and to fix a mistake. sorry for the confusion.
Is that all log? Didn't see iptables and dnsmasq.
Thats the second part of the output from systemctl status, I added the commands above and deleted the space in the middle of the output to make it a bit clearer
Why different configuration folder name?
lnxrouter.wlan0.conf.3u7
andlnxrouter.wlx984827adde1a.conf.3u7
Sorry I changed all of the wlx984827adde1a to wlan0 for clarity, I must have missed that one. They are all the same
You chould try adding iptables.service and networkmanager.service as dependency. Try add a 2-minutes delay before calling
lnxrouter
to to have system boot completely
This produces no change. Router still broadcasts but nothing will connect to it. Here's my updated .service file
[Unit] Description=linux-router After=network.target iptables.service networkmanager.service [Service] Type=simple ExecStart=/home/ubuntu/Downloads/linux-router-master/lnxrouter --ap wlx984827ad> KillSignal=SIGINT Restart=always RestartSec=10 StandardOutput=syslog StandardError=syslog SyslogIdentifier=linux-router [Install] WantedBy=multi-user.target
I also tried starting the service manually (disabled on startup, systemctl start) after the system had booted. Still runs with issues, broadcast ap / no connections)
I also managed to get it running from rc.local. Surprisingly enough it was because I forgot the & at the end of the command to allow it to fork. I ran it like this for a while and it still ran with the same issues, broadcast ap / no connections. I fixed the file and booted back into grub, where I ran rc.local manually, and in that state it worked as expected.
It really seems to me like any type of background / automatic start state results in the same issue, where it broadcasts the ap but nothing will connect to it. Any time I start it manually, through the cli or a script including rc.local) it runs as expected.
The only other thing to note, last night I was playing around with it and although I don't remember the exact circumstances, I was seeing the errors from check_wifi_settings() "WARN: Using 'iwconfig', not as good as 'iw'" and "ERROR: Can't use 'iwconfig' to operation this WiFi interface neither". I'm sorry that I can't seem to reproduce today, but it was right before I forgot the & in rc.local and gave up for the night
I appreciate your help
@eschwelgin
I tried to run by systemd. Turned out dnsmasq
failed
In dnsmasq.conf
log-facility=/dev/stdout
causes error
cannot open log /dev/stdout: No such device or address
in systemd environment.
(You could try modifying StandardOutput=syslog
to something else )
For a quick workaround you can delete log-facility=/dev/stdout
BTW, I have to fix watchdog. It didn't react when dnsmasq fails. (and it couldn't recognize zombie process)
@eschwelgin Changed how dnsmasq outputs. Now it uses named pipe. You could try it again.
Sorry to reopen an old thread but I tried to run lnxrouter using a script:
`#!/bin/sh -e -p
sleep 120
/usr/sbin/lnxrouter -i eth0 &
sleep 2
disown -a
sleep 2
exit 0`
This script is launched by cron (@reboot) on a Raspberry Pi 4 and gives internet to an AVM Fritz Extender that should run a wifi network. If I launch lnxrouter -i eth0 manually it works fine, but on reboot I have a running router that I cannot connect to because does not receive an IP address. Any hint about it? Thank you
Changed how dnsmasq outputs. Now it uses named pipe. You could try it again.
Just because nobody else said so explicitly: this works now. Here is my service definition lnxrouter-hotspot.service
[Unit]
Description=lnxrouter Hotspot Service
After=network.target iptables.service networkmanager.service
[Service]
Type=simple
ExecStart=/usr/local/bin/lnxrouter --ap wlx40a5ef05a66a "jordan-t4pro" -p "xxxxxxxx" --no-virt
Restart=always
KillSignal=SIGINT
StandardOutput=syslog
StandardError=syslog
SyslogIdentifier=lnxrouter-hotspot
User=root
RestartSec=10
[Install]
WantedBy=multi-user.target
N.B. to other readers: you may not want --no-virt
I came here to try this script after failing to get my USB 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter
working in ap mode using nmcli
with WPA-PSK (or even WEP, shudder). Setting things up "the old-fashioned way" using lnxrouter worked GREAT.
Thank you for this script!
Hello, thank you for your job. I tried running this (on Raspberry 3, with 2 external usb dongles), as well as the original create_ap and just like the original script, it seems to have an issue, with the interfaces, if run from crontab. Any chance to run it as a service, so it will be much easier, to run it at start up? Also both the script seem to have an issue, with wlan0 -> wlan1 relay. The speed is cut drastically, best I can get is 50% less download rate on wlan1, compared to wlan0. The upload speed seems unaffected that much. I know the hardware can perform a lot better, since running the LEDE, on the set up, only has around 10% downgrade. For additional information, on-board wifi disabled, as well as network-manager is off. Clean install of debian.
Thanks again.