search

geary / AnyTone-D868UV

Unofficial issue tracker for AnyTone AT-D868UV and AT-D878UV radios and firmware
57 stars 1 forks source link

Finer steps for volume control, especially at low volumes #29

Open geary opened 6 years ago

geary commented 6 years ago

Firmware 2.27

The volume knob steps don't allow fine enough adjustment. Even the lowest volume on the "indoor" setting can be too loud in some quieter environments, and there is too large a jump from the lowest volume to the next.

See also #21. Continuously variable volume would be the best solution, but that may require a hardware change. In the meantime, there ought to be a way to get finer volume steps for low volumes.

(from Scott Waggoner via Facebook)

mostlychris commented 6 years ago

I agree. In a quiet environment, especially with over deviating DMR stations, the volume is just too loud. I wonder if there is a way to enable some AGC to at least average out the sound levels so there is not constant juggling of the volume when different stations talk.

geary commented 6 years ago

@mostlychris Definitely a problem on DMR, and to a lesser extent on analog. See #32 for a feature request specifically on adding AGC. The neat thing that the radio could do in addition to basic AGC would be to remember the current AGC setting individually for each recent DMR station since it has their IDs.

myzinsky commented 5 years ago

It’s definitely to loud even in the smallest setting! People get offended easily when I’m just hearing with the radio. Is there a way to fix it? A sw patch could do that IMHO.

aerodan commented 4 years ago

Any progress on this? At the lowest setting the 878 is as loud as most radios on half volume.

AE2WM commented 4 years ago

I agree that this is a problem, especially when one is wearing a headset with a boom mic. Even at the lowest setting, the sound is irritatingly loud. This should be a simple firmware fix.

barneyfs41 commented 4 years ago

I seem to have the opposite problem, when I first got the 878 it was too loud now it has drastically reduced volume. Even set to 9 and the volume all the way up it is about half of what it was. anyone else have this problem?

AE2WM commented 4 years ago

Make sure you haven’t programmed the max volume to a low setting. In the CPS program, go to Optional Settings/Volume-Audio, and see what the settings are. 8 will give you the greatest maximum volume. Indoors will cut down the max volume considerably. These settings, unfortunately, don’t solve the minimum volume problem.

Bill McGrath

mailto:wfm3@cornell.edu wfm3@cornell.edu

602-989-9300

From: barneyfs41 notifications@github.com Sent: Tuesday, March 17, 2020 13:41 To: geary/AnyTone-D868UV AnyTone-D868UV@noreply.github.com Cc: Bill McGrath wfm3@cornell.edu; Comment comment@noreply.github.com Subject: Re: [geary/AnyTone-D868UV] Finer steps for volume control, especially at low volumes (#29)

I seem to have the opposite problem, when I first got the 878 it was too loud now it has drastically reduced volume. Even set to 9 and the volume all the way up it is about half of what it was. anyone else have this problem?

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/geary/AnyTone-D868UV/issues/29#issuecomment-600286250 , or unsubscribe https://github.com/notifications/unsubscribe-auth/AOIC5NCZOFISL74HABHEPGDRH7N4FANCNFSM4FAXUWBA . https://github.com/notifications/beacon/AOIC5NB3CHOTBERX6IJDSYLRH7N4FA5CNFSM4FAXUWBKYY3PNVWWK3TUL52HS4DFVREXG43VMVBW63LNMVXHJKTDN5WW2ZLOORPWSZGOEPD2IKQ.gif

ldaponte commented 4 years ago

I'm having super low RX audio volume on my AnyTone 878. I have the Max Vol Level set to 8 both in the radio and the CPS Volume/Audio section. With the RX set to 8 I can almost not hear anything even in a completely quiet room.

barneyfs41 commented 4 years ago

I checked the CPS and it is set at 8. still getting low RX volume, I have to keep it at full volume when it is on my belt.

mprezioso commented 4 years ago

I'm also having similar audio issues as ldaponte, and barneyfs41. I've tried going back to a base code plug and testing with FM out to verify some things but with the same results. I've now tried it with an External Bluetooth speaker and apparently that works depending on the Bluetooth speaker. Speakers I've tested with are the Bose soundlink mini "poor audio but could be due to Bose audio settings Volume was OK but audio had to much bass and distorted the audio ". Also tried with Anker Soundcore "much better audio results, volume was good and sound quality was clear" Much of this seams to have started after first firmware update 1.13 to 1.15 I've since also tried Firmware 1.17 but still no better results.

ldaponte commented 4 years ago

I'm still testing. I thought it was related to my OpenSpot 3 but it is not as I get the same results sending simplex DMR from a hytera and I get the same low audio level out of the AnyTone. The audio quality sounds broken and very raspi and I have to turn the volume to full to even hear that. The TX output of the AnyTone sounds fine listening on the hytera and also radio check is also reported fine by others on brandmeister via the OpenSpot. I've tried firmware 1.17 and 1.09 but no difference. I've also done a factory reset on the AnyTone with no luck. DMR RX was fine last year right after I purchased the radio.

-Larry

On Thu, Apr 9, 2020 at 00:18 mprezioso notifications@github.com wrote:

I'm also having similar audio issues as ldaponte, and barneyfs41. I've tried going back to a base code plug and testing with FM out to verify some things but with the same results. I've now tried it with an External Bluetooth speaker and apparently that works depending on the Bluetooth speaker. Speakers I've tested with are the Bose soundlink mini "poor audio but could be due to Bose audio settings Volume was OK but audio had to much bass and distorted the audio ". Also tried with Anker Soundcore "much better audio results, volume was good and sound quality was clear" Much of this seams to have started after first firmware update 1.13 to 1.15 I've since also tried Firmware 1.17 but still no better results.

— You are receiving this because you commented. Reply to this email directly, view it on GitHub https://github.com/geary/AnyTone-D868UV/issues/29#issuecomment-611223505, or unsubscribe https://github.com/notifications/unsubscribe-auth/ABACY4CSUA6DZIANGLWCOZ3RLTZ4VANCNFSM4FAXUWBA .

barneyfs41 commented 4 years ago

Any luck with the audio issues on the anytone ? Larry or Michael

mprezioso commented 4 years ago

@barneyfs41 Nothing yet on my end. I've even just updated to the most recent firmware and still no luck. It's a real bummer as it basically reduces the HT to home OPS at best, and even then I can't copy most things at max vol.

ldaponte commented 3 years ago

I finally returned the 878 to the dealer and Anytone agreed to replace the radio. It appears to be some sort of failure/fault that resetting to factory defaults does not resolve. For me the root cause is unknown. The reseller agreed to give me store credit as I did not want a replacement.

Cheers Larry

AsciiWolf commented 4 months ago

Is the volume still too loud with recent firmware?