Success with the MSZ-GE60/71/80 series and M5Stack Atom Lite

[wrouesnel]

A note that I've had success with this code on an MSZ-GE60/71/80 series using an M5 Atom Lite.

Crucially, I couldn't build the current develop branch to install this, but I was able to cherry-pick across the UART pin configuration commits and get it working (pushed on my fork: https://github.com/wrouesnel/esphome-mitsubishiheatpump) On this unit the baud rate was 2400, and with the M5 Atom I needed to use pin remapping for some of the broken out top pins. It was also necessary to add the 10kOhm pull up resistors from the TX/RX pins, but I did not need any level shifters (of course this is literally a few hours old so don't trust me that the M5 won't die suddenly or something).

(note: this is ESPhome as I do it - i.e. time keeping etc. are all being configured in that home.yaml file)

The two commits I've pulled across (UART config and packet logging) both seem to work well and it'd be great if they were included in the master branch).

Also a note that the pin numbers you give are IO pin numbers would've saved some confusion.

# Codes for a Mitsubishi Heatpump running on an M5Stack Atom Lite
# substitutions:
#   name: hptest
#   friendly_name: Test Heatpump

packages:
  home: !include home.yaml

external_components:
- source:
    type: local
    path: components

esphome:
  name: me-hpctrl
  name_add_mac_suffix: true
  # Boards tested: ESP-01S (ESP8266), Wemos D1 Mini (ESP8266); ESP32 Wifi-DevKit2
  project:
    name: esphome.mitsubishi-heatpump
    version: "1.0"
  platform: ESP32
  board: m5stack-core-esp32

# Enable logging
logger:
  # ESP8266 only - disable serial port logging, as the HeatPump component
  # needs the sole hardware UART on the ESP8266
  level: VERBOSE
  #baud_rate: 0

web_server:
  port: 80

wifi:
  ap: {}

captive_portal:

ota:

# Enable Home Assistant API
api:

# Text sensors with general information.
text_sensor:
  # Expose ESPHome version as sensor.
  - platform: version
    name: ESPHome Version
  # Expose WiFi information as sensors.
  - platform: wifi_info
    ip_address:
      name: IP
    ssid:
      name: SSID
    bssid:
      name: BSSID

# Sensors with general information.
sensor:
  # Uptime sensor.
  - platform: uptime
    name: Uptime

  # WiFi Signal sensor.
  - platform: wifi_signal
    name: WiFi Signal
    update_interval: 60s

climate:
  - platform: mitsubishi_heatpump
    name: Air Conditioning

    # ESP32 only - change UART0 to UART1 or UART2 and remove the
    # logging:baud_rate above to allow the built-in UART0 to function for
    # logging.
    hardware_uart: UART2
    tx_pin: 21
    rx_pin: 25 
    baud_rate: 2400

EDIT: Bonus picture of the prototype board shield (for the pull up resistors) where I connected the module - fits right under the case (I used a CN105 pin header, but didn't have the right crimping tools to use a proper one way connector)

[Bascht74]

Hi @wrouesnel I used a simial setup.

Just used the Atom Lite and a GROVE Cable (connects to pin 25/32), no pullup resistors, no level shifters. I cut the plastic of on end of the GROVE Cable and insertet freeed pins into a JST PAP-05V-S housing. Click, Click, Click, Click --> ready. So I have a cable that I can connect directly to the Lite and on the other side into the CN105-Port...

Using your version, only with tx_pin: 32, rx_pin: 26, boud rate is 2400 as well...

[BenJamesAndo]

Thank you both for this information. I was able to get this running on a M5 Atom Matrix that I had lying around. I used a Grove to 4 pin dupont cable. I then plugged that into a Dupont to CN105 cable. It meant no cable crimping but ideally I would like to improve it to just use one cable similar to Bascht74.

I was able to get it running using geoffdavis version with

external_components:
  - source: github://geoffdavis/esphome-mitsubishiheatpump@develop

and

esphome:
  name: mitsubishi-ac
  project:
    name: esphome.mitsubishi-ac
    version: "MSZ-GA60VA"
  platform: ESP32
  board: m5stack-atom
  platformio_options:
    build_unflags:
      - "-std=gnu++11"
    build_flags:
      - "-std=gnu++17"

I used baud_rate of 9600. 2400 didn't work for me.

    hardware_uart: UART1
    tx_pin: 32
    rx_pin: 26
    baud_rate: 9600

It also worked with wrouesnel fork and echavet's fork echavet being my favourite at the moment as it has the most controls.

[Bascht74]

You could get a grove cable, cut one connector ro free the four metal arms and put them into a single CN105 connector. I just used the cable, a very sharp knife an the CN105 connector and get a new cable that I can plug in the Atom on one side and the Mitsubishi on the other…

[tmchow]

I’ve got a grove cable and a PAP-05V-S. What exactly is the wiring configuration into the PAP-05V-S?