issues
search
gvJaime
/
microspot
3D printable - DIY microscope
Other
13
stars
12
forks
source link
issues
Newest
Newest
Most commented
Recently updated
Oldest
Least commented
Least recently updated
ElecBase Lid bolt holes need to be tighter
#146
gvJaime
closed
7 years ago
0
ElecLid lower bolts are too difficult to put in place
#145
gvJaime
closed
7 years ago
0
ElecBase doesn't facilitate an easy removal of LowerCover
#144
gvJaime
closed
7 years ago
0
ElecLid doesn't leave space for wires
#143
gvJaime
closed
7 years ago
0
Bracket holes need more clearance
#142
gvJaime
closed
7 years ago
0
FlexiLens crane collides with USB cable, when the port is on the side of the phone.
#141
gvJaime
closed
7 years ago
1
Add a zip tie to each XAxis LM8UU
#140
gvJaime
closed
7 years ago
0
Make LeafTest more curved
#139
gvJaime
closed
7 years ago
0
Add adjusting bolt for Z bearing
#138
gvJaime
closed
7 years ago
0
LensMount needs to reach lower positions
#137
gvJaime
closed
7 years ago
0
Bracket bolts collide with XCarriage
#136
gvJaime
closed
7 years ago
0
Make Lens mount 1mm shorter so the brackets end up aligned.
#135
gvJaime
closed
7 years ago
0
Lens Mount doesn't fit the bracket.
#134
gvJaime
closed
7 years ago
0
SampleFix is brittle
#133
gvJaime
closed
7 years ago
0
Add nuts for the TubeLid bolts, in LowerCover
#132
gvJaime
closed
7 years ago
0
Add 623ZZs to the flexible brackets to help them bend properly.
#131
gvJaime
closed
7 years ago
0
The "MicroSpot" sign isn't visible enough
#130
gvJaime
closed
7 years ago
0
NEMA Pulley needs dimensional accuracy beyond regular 3D printing capabilities
#129
gvJaime
opened
7 years ago
1
YCarriage bearingFix bolts have an uncommon length
#128
gvJaime
closed
7 years ago
0
Make a new AxisShield for the new YCarriage
#127
gvJaime
closed
7 years ago
0
Increase collimation in TubeLid
#126
gvJaime
closed
7 years ago
2
Easily interchangeable light tube
#125
gvJaime
closed
7 years ago
1
Redesign YCarriage so it completely attaches to the LM8UUs
#124
gvJaime
closed
7 years ago
0
Integrate StringTensioner in XCarriage
#123
gvJaime
closed
7 years ago
0
Replace PhoneCarriage dies with flexible filament structures
#122
gvJaime
closed
7 years ago
0
StringTensioner zip tie slots don't match XCarriage
#121
gvJaime
closed
7 years ago
1
Holding each YCarriage bearing with two zipties could help prevent Axis skewing.
#120
gvJaime
closed
7 years ago
1
Update the Electronics box design.
#119
gvJaime
closed
7 years ago
0
Carve indications on LidPhoneCarriage about which way to turn the thumbwheel
#118
gvJaime
closed
7 years ago
0
LowerLid bolt threads need to stick out a little bit more.
#117
gvJaime
closed
7 years ago
0
AxisShield collides with NEMA motors
#116
gvJaime
closed
7 years ago
0
BearingHolder SmRodLanes don't continue on LowerLid
#115
gvJaime
closed
7 years ago
0
Current linear guides layout on PhoneCarriage allows for an accidental rolling motion
#114
gvJaime
closed
7 years ago
0
YCarriage rod slots need a bit of clearance in the end
#113
gvJaime
closed
7 years ago
0
Lens crane SmallLongArms collide with OpticFit
#112
gvJaime
closed
7 years ago
0
Lens crane ends up getting too close to the phone, and that renders the crane unusable for bigger phones
#111
gvJaime
closed
7 years ago
0
The new YCarriage design leaves the axis too open
#110
gvJaime
closed
7 years ago
0
PhoneCarriage's clearances cause variation on the phone's pitch.
#109
gvJaime
closed
7 years ago
0
Lens adjustment mechanism is counter intuitive, and easy to get wrong
#108
gvJaime
closed
7 years ago
1
PhoneCarriage 3d printing yields bad results because of support material.
#107
gvJaime
closed
7 years ago
0
YCarriage print errors can produce axis skewing
#106
gvJaime
closed
7 years ago
0
Lenses must be fixed to PhoneCarriage
#105
gvJaime
closed
7 years ago
0
Light tube is too short
#104
gvJaime
closed
7 years ago
0
ThumbWheelHolder lower surface needs adjustment
#103
gvJaime
closed
7 years ago
0
FrontCorner corner fillet is not wide enough
#102
gvJaime
closed
7 years ago
0
Consider @JMG1 linear guides
#101
gvJaime
closed
6 years ago
0
MainStructure doesn't fit for centered camera phones
#100
gvJaime
closed
7 years ago
1
LowerCover lacks a Fillet on the front
#99
gvJaime
closed
7 years ago
0
MainStructure bolt orientation is wrong
#98
gvJaime
closed
7 years ago
0
MechEndstop board sourcing is too difficult
#97
gvJaime
closed
7 years ago
1
Previous
Next