Closed Prior99 closed 2 years ago
I think this might be related to this issue: https://github.com/home-assistant/operating-system/issues/1633
Here is a chunk of relevant log from the Host after this happened again:
[ 7558.718488] usb 3-4: USB disconnect, device number 3
[ 7558.983570] usb 3-4: new full-speed USB device number 4 using xhci_hcd
[ 7559.110829] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[ 7559.110831] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 7559.110832] usb 3-4: Product: ConBee II
[ 7559.110833] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 7559.110834] usb 3-4: SerialNumber: DE2405775
[ 7569.121432] xhci_hcd 0000:0a:00.3: Abort failed to stop command ring: -110
[ 7569.141643] xhci_hcd 0000:0a:00.3: xHCI host controller not responding, assume dead
[ 7569.141656] xhci_hcd 0000:0a:00.3: HC died; cleaning up
[ 7569.141763] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[ 7569.141772] usb 3-4: can't set config #1, error -62
[ 7569.141881] usb 3-1: USB disconnect, device number 2
[ 7569.141979] ftdi_sio ttyUSB0: error from flowcontrol urb
[ 7569.142240] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 7569.142254] ftdi_sio 3-1:1.0: device disconnected
[ 7569.142438] usb 3-4: USB disconnect, device number 4
[ 7715.047386] kauditd_printk_skb: 16 callbacks suppressed
I'm still seeing the same even after disabling BT as suggested in #1633, I even disabled wifi.
[ 64.125673] eth0: renamed from veth27218aa
[ 64.138943] IPv6: ADDRCONF(NETDEV_CHANGE): veth5710211: link becomes ready
[ 64.138970] hassio: port 8(veth5710211) entered blocking state
[ 64.138972] hassio: port 8(veth5710211) entered forwarding state
[ 66.225519] usb 1-3: USB disconnect, device number 5
[ 66.529410] usb 1-3: new full-speed USB device number 6 using xhci_hcd
[ 66.658372] usb 1-3: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[ 66.658376] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 66.658379] usb 1-3: Product: ConBee II
[ 66.658381] usb 1-3: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[ 66.658383] usb 1-3: SerialNumber: DE2215018
[ 66.659558] cdc_acm 1-3:1.0: ttyACM0: USB ACM device
[ 83.413973] kauditd_printk_skb: 1 callbacks suppressed
[ 83.413974] audit: type=1334 audit(1643639822.963:178): prog-id=14 op=UNLOAD
[ 83.413978] audit: type=1334 audit(1643639822.963:179): prog-id=13 op=UNLOAD
[ 85.725137] audit: type=1334 audit(1643639825.274:180): prog-id=12 op=UNLOAD
[ 85.725143] audit: type=1334 audit(1643639825.274:181): prog-id=11 op=UNLOAD
[ 95.784499] hassio: port 9(veth6a32fd8) entered blocking state
[ 95.784502] hassio: port 9(veth6a32fd8) entered disabled state
[ 95.784628] device veth6a32fd8 entered promiscuous mode
[ 95.784848] hassio: port 9(veth6a32fd8) entered blocking state
[ 95.784850] hassio: port 9(veth6a32fd8) entered forwarding state
I think this kernel bug could be the reason: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Here is another chunk of kernel log:
[142420.753693] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142420.753709] usb 3-4: can't set config #1, error -62
[142421.218564] usb 3-4: USB disconnect, device number 21
[142421.482455] usb 3-4: new full-speed USB device number 22 using xhci_hcd
[142421.609794] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142421.609799] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142421.609802] usb 3-4: Product: ConBee II
[142421.609804] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142421.609806] usb 3-4: SerialNumber: DE2405775
[142431.521691] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142431.521705] usb 3-4: can't set config #1, error -62
[142431.522762] usb 3-4: USB disconnect, device number 22
[142431.759246] usb 3-4: new full-speed USB device number 23 using xhci_hcd
[142431.887000] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142431.887005] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142431.887007] usb 3-4: Product: ConBee II
[142431.887009] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142431.887011] usb 3-4: SerialNumber: DE2405775
[142441.089699] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142441.089712] usb 3-4: can't set config #1, error -62
[142441.610563] usb 3-4: USB disconnect, device number 23
[142441.866371] usb 3-4: new full-speed USB device number 24 using xhci_hcd
[142441.993383] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142441.993387] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142441.993390] usb 3-4: Product: ConBee II
[142441.993392] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142441.993394] usb 3-4: SerialNumber: DE2405775
[142451.889703] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142451.889714] usb 3-4: can't set config #1, error -62
[142451.889816] usb 3-4: USB disconnect, device number 24
[142452.126837] usb 3-4: new full-speed USB device number 25 using xhci_hcd
[142452.254110] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142452.254112] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142452.254113] usb 3-4: Product: ConBee II
[142452.254114] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142452.254115] usb 3-4: SerialNumber: DE2405775
[142461.441723] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142461.441738] usb 3-4: can't set config #1, error -62
[142462.013124] usb 3-4: USB disconnect, device number 25
[142462.266672] usb 3-4: new full-speed USB device number 26 using xhci_hcd
[142462.393944] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142462.393948] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142462.393951] usb 3-4: Product: ConBee II
[142462.393953] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142462.393954] usb 3-4: SerialNumber: DE2405775
[142472.305704] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142472.305723] usb 3-4: can't set config #1, error -62
[142472.305889] usb 3-4: USB disconnect, device number 26
[142472.544440] usb 3-4: new full-speed USB device number 27 using xhci_hcd
[142472.671827] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142472.671832] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142472.671835] usb 3-4: Product: ConBee II
[142472.671837] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142472.671838] usb 3-4: SerialNumber: DE2405775
[142481.905725] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142481.905740] usb 3-4: can't set config #1, error -62
[142482.410314] usb 3-4: USB disconnect, device number 27
[142482.667269] usb 3-4: new full-speed USB device number 28 using xhci_hcd
[142482.794607] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142482.794612] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142482.794614] usb 3-4: Product: ConBee II
[142482.794616] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142482.794618] usb 3-4: SerialNumber: DE2405775
[142492.737743] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142492.737757] usb 3-4: can't set config #1, error -62
[142492.737886] usb 3-4: USB disconnect, device number 28
[142492.975035] usb 3-4: new full-speed USB device number 29 using xhci_hcd
[142493.102377] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142493.102381] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142493.102384] usb 3-4: Product: ConBee II
[142493.102386] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142493.102387] usb 3-4: SerialNumber: DE2405775
[142502.289725] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142502.289738] usb 3-4: can't set config #1, error -62
[142502.814149] usb 3-4: USB disconnect, device number 29
[142503.065874] usb 3-4: new full-speed USB device number 30 using xhci_hcd
[142503.193190] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142503.193195] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142503.193197] usb 3-4: Product: ConBee II
[142503.193199] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142503.193201] usb 3-4: SerialNumber: DE2405775
[142513.089751] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142513.089765] usb 3-4: can't set config #1, error -62
[142513.089902] usb 3-4: USB disconnect, device number 30
[142513.327643] usb 3-4: new full-speed USB device number 31 using xhci_hcd
[142513.454982] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142513.454986] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142513.454989] usb 3-4: Product: ConBee II
[142513.454991] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142513.454993] usb 3-4: SerialNumber: DE2405775
[142522.657738] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142522.657752] usb 3-4: can't set config #1, error -62
[142523.222882] usb 3-4: USB disconnect, device number 31
[142523.482446] usb 3-4: new full-speed USB device number 32 using xhci_hcd
[142523.609800] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142523.609806] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142523.609809] usb 3-4: Product: ConBee II
[142523.609811] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142523.609813] usb 3-4: SerialNumber: DE2405775
[142533.521751] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142533.521767] usb 3-4: can't set config #1, error -62
[142533.522016] usb 3-4: USB disconnect, device number 32
[142533.759240] usb 3-4: new full-speed USB device number 33 using xhci_hcd
[142533.886633] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142533.886637] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142533.886640] usb 3-4: Product: ConBee II
[142533.886642] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142533.886643] usb 3-4: SerialNumber: DE2405775
[142543.073730] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142543.073743] usb 3-4: can't set config #1, error -62
[142543.634091] usb 3-4: USB disconnect, device number 33
[142543.898399] usb 3-4: new full-speed USB device number 34 using xhci_hcd
[142544.025333] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142544.025338] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142544.025340] usb 3-4: Product: ConBee II
[142544.025342] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142544.025344] usb 3-4: SerialNumber: DE2405775
[142553.937768] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142553.937782] usb 3-4: can't set config #1, error -62
[142553.938121] usb 3-4: USB disconnect, device number 34
[142554.174845] usb 3-4: new full-speed USB device number 35 using xhci_hcd
[142554.302292] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142554.302296] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142554.302299] usb 3-4: Product: ConBee II
[142554.302301] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142554.302303] usb 3-4: SerialNumber: DE2405775
[142563.489746] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142563.489759] usb 3-4: can't set config #1, error -62
[142564.045790] usb 3-4: USB disconnect, device number 35
[142564.298985] usb 3-4: new full-speed USB device number 36 using xhci_hcd
[142564.425984] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142564.425989] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142564.425991] usb 3-4: Product: ConBee II
[142564.425993] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142564.425995] usb 3-4: SerialNumber: DE2405775
[142574.337783] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142574.337797] usb 3-4: can't set config #1, error -62
[142574.337939] usb 3-4: USB disconnect, device number 36
[142574.575451] usb 3-4: new full-speed USB device number 37 using xhci_hcd
[142574.703138] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142574.703142] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142574.703145] usb 3-4: Product: ConBee II
[142574.703147] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142574.703148] usb 3-4: SerialNumber: DE2405775
[142583.922710] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142583.922727] usb 3-4: can't set config #1, error -62
[142584.460613] usb 3-4: USB disconnect, device number 37
[142584.714602] usb 3-4: new full-speed USB device number 38 using xhci_hcd
[142584.844666] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142584.844671] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142584.844673] usb 3-4: Product: ConBee II
[142584.844675] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142584.844676] usb 3-4: SerialNumber: DE2405775
[142594.770604] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142594.770619] usb 3-4: can't set config #1, error -62
[142594.771645] usb 3-4: USB disconnect, device number 38
[142595.007060] usb 3-4: new full-speed USB device number 39 using xhci_hcd
[142595.137367] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142595.137372] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142595.137374] usb 3-4: Product: ConBee II
[142595.137376] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142595.137378] usb 3-4: SerialNumber: DE2405775
[142604.337784] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142604.337798] usb 3-4: can't set config #1, error -62
[142604.877559] usb 3-4: USB disconnect, device number 39
[142605.130208] usb 3-4: new full-speed USB device number 40 using xhci_hcd
[142605.257130] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142605.257135] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142605.257137] usb 3-4: Product: ConBee II
[142605.257140] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142605.257141] usb 3-4: SerialNumber: DE2405775
[142615.153799] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142615.153815] usb 3-4: can't set config #1, error -62
[142615.153983] usb 3-4: USB disconnect, device number 40
[142615.391669] usb 3-4: new full-speed USB device number 41 using xhci_hcd
[142615.519013] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142615.519017] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142615.519020] usb 3-4: Product: ConBee II
[142615.519022] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142615.519023] usb 3-4: SerialNumber: DE2405775
[142624.721810] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142624.721824] usb 3-4: can't set config #1, error -62
[142625.293104] usb 3-4: USB disconnect, device number 41
[142625.546481] usb 3-4: new full-speed USB device number 42 using xhci_hcd
[142625.673845] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142625.673850] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142625.673852] usb 3-4: Product: ConBee II
[142625.673855] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142625.673856] usb 3-4: SerialNumber: DE2405775
[142635.586184] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142635.586200] usb 3-4: can't set config #1, error -62
[142635.586340] usb 3-4: USB disconnect, device number 42
[142635.823281] usb 3-4: new full-speed USB device number 43 using xhci_hcd
[142635.950682] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142635.950687] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142635.950689] usb 3-4: Product: ConBee II
[142635.950691] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142635.950692] usb 3-4: SerialNumber: DE2405775
[142645.137819] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142645.137834] usb 3-4: can't set config #1, error -62
[142645.706168] usb 3-4: USB disconnect, device number 43
[142645.962121] usb 3-4: new full-speed USB device number 44 using xhci_hcd
[142646.089390] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142646.089395] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142646.089398] usb 3-4: Product: ConBee II
[142646.089400] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142646.089401] usb 3-4: SerialNumber: DE2405775
[142655.985789] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142655.985804] usb 3-4: can't set config #1, error -62
[142655.985955] usb 3-4: USB disconnect, device number 44
[142656.222902] usb 3-4: new full-speed USB device number 45 using xhci_hcd
[142656.350639] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142656.350644] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142656.350646] usb 3-4: Product: ConBee II
[142656.350648] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142656.350650] usb 3-4: SerialNumber: DE2405775
[142665.537846] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142665.537861] usb 3-4: can't set config #1, error -62
[142666.122843] usb 3-4: USB disconnect, device number 45
[142666.378742] usb 3-4: new full-speed USB device number 46 using xhci_hcd
[142666.506035] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142666.506040] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142666.506042] usb 3-4: Product: ConBee II
[142666.506044] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142666.506046] usb 3-4: SerialNumber: DE2405775
[142676.433968] xhci_hcd 0000:0a:00.3: Timeout while waiting for configure endpoint command
[142676.433983] usb 3-4: can't set config #1, error -62
[142676.434125] usb 3-4: USB disconnect, device number 46
[142676.671515] usb 3-4: new full-speed USB device number 47 using xhci_hcd
[142676.799181] usb 3-4: New USB device found, idVendor=1cf1, idProduct=0030, bcdDevice= 1.00
[142676.799186] usb 3-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[142676.799188] usb 3-4: Product: ConBee II
[142676.799190] usb 3-4: Manufacturer: dresden elektronik ingenieurtechnik GmbH
[142676.799192] usb 3-4: SerialNumber: DE2405775
I think this kernel bug could be the reason: https://bugzilla.kernel.org/show_bug.cgi?id=202541
Maybe, it seems to me though that more errors appear in their case?
To me it seems that xHCI host controller not responding, assume dead
is the main culprit, but maybe there is more to it. Googling a bit it seems that others have a very similar issue with AMD/Ryzen based systems:
https://unix.stackexchange.com/questions/669015/xhci-restart-needed
I think I've also heard from other places where some AMD systems had USB issues. Can you try a BIOS update? Also just to make sure, did you try use a different extension cord?
Have you tried other Linux distributions with the same system?
I plan to update the Linux kernel to the latest stable 5.10 version with 7.3, and then also update to the latest LTS on dev. Both variants probably worth testing, maybe something upstream fixes it.
You are right. I changed to a port with another controller and the problem hasn't happened since. Closing this. Thanks :)
@Prior99 Can you exactly tell me what you did? I have tried all my USB ports. I'm using an Intel® nUC KIt nUC8¡7BeH
@gieljnssns on my board there were 4 ports from the controller and 2 from the CPU directly. I switched to the direct CPU.
Describe the issue you are experiencing
I am using the Conbee II Stick on Home Assistant OS on a normal x86_64 machine with a decent CPU und a decent PSU.
Sometimes the stick will run smoothely for days, sometimes only for minutes, until it will disconnect and then reconnect periodically.
Yes, I am using an extension cord.
What operating system image do you use?
generic-x86-64 (Generic UEFI capable x86-64 systems)
What version of Home Assistant Operating System is installed?
7.1
Did you upgrade the Operating System.
Yes
Steps to reproduce the issue
Anything in the Supervisor logs that might be useful for us?
Anything in the Host logs that might be useful for us?
System Health information
System Health
Home Assistant Community Store
GitHub API | ok -- | -- Github API Calls Remaining | 4794 Installed Version | 1.19.3 Stage | running Available Repositories | 967 Downloaded Repositories | 34Home Assistant Cloud
logged_in | false -- | -- can_reach_cert_server | ok can_reach_cloud_auth | ok can_reach_cloud | okHome Assistant Supervisor
host_os | Home Assistant OS 7.1 -- | -- update_channel | stable supervisor_version | supervisor-2021.12.2 docker_version | 20.10.9 disk_total | 228.5 GB disk_used | 154.6 GB healthy | true supported | true board | generic-x86-64 supervisor_api | ok version_api | ok installed_addons | deCONZ (6.11.1), File editor (5.3.3), Terminal & SSH (9.3.0), BorgBackup (0.56), NGINX Home Assistant SSL proxy (3.1.1), Let's Encrypt (4.12.0), Portainer (2.0.0), Mosquitto broker (6.0.1)Lovelace
dashboards | 13 -- | -- resources | 19 views | 26 mode | yamlSpotify
api_endpoint_reachable | ok -- | --Additional information
Please note that the Host Logs are from a different boot. I can add new Host Logs once the problem occured again.