Some Optimizations - Githubissues

i have some more modes as you support currently, can you add these?

Mode: MildDry

Please add a funktion to change SwingH & SwingV in Thermostat Card

and all “default_*_mode” are not working they are always off only celsius and hvac_model are working any ideas? Its only working when i send a command like this: http://192.168.178.50/cm?cmnd=IRhvac{"Vendor":"PANASONIC_AC","Model":1,"Mode":"Cool","Power":"On","Celsius":"On","Temp":24,"FanSpeed":"Low","SwingV":"Highest","SwingH":"RightMax","Quiet":"Off","Turbo":"On","Econo":"On","Light":"Off","Filter":"Off","Clean":"Off","Beep":"Off","Sleep":-1}

`
#Büro
  - platform: tasmota_irhvac
    name: "Klimaanlage Buero"
    command_topic: "cmnd/Klimaanlage_Buero_5A7A65/irhvac"
    # Pick one of the following:
    # State is updated when the tasmota device receives an IR signal (includes own transmission and original remote)
    # useful when a normal remote is in use alongside the tasmota device, may be less reliable than the second option.
    state_topic: "tele/Klimaanlage_Buero_5A7A65/RESULT"
    # State is updated when the tasmota device completes IR transmissionm, should be pretty reliable.
    #state_topic: "stat/your_tasmota_device/RESULT"
    # Uncomment if your 'available topic' of Tasmota IR device are different (if device in HA is disabled)
    #availability_topic: "tele/your_tasmota_device/LWT"
    temperature_sensor: sensor.wohnzimmer_temperatursensor_snzb_02_temperature
    humidity_sensor: sensor.wohnzimmer_temperatursensor_snzb_02_humidity #optional - default None
    #power_sensor: binaly_sensor.kitchen_ac_power #optional - default None
    vendor: "PANASONIC_AC"
    min_temp: 16 #optional - default 16 int value
    max_temp: 30 #optional - default 32 int value
    target_temp: 26 #optional - default 26 int value
    initial_operation_mode: "off" # optional - default "off" string value (one of the "supported_modes")
    away_temp: 24 #optional - default 24 int value
    precision: 1 #optional - default 1 int or float value. Can be set to 1, 0.5 or 0.1
    supported_modes:
      - "auto"
      - "heat"
      - "cool"
      - "dry"
      - "fan_only" # Use "fan_only" even if Tasmota shows "Mode":"Fan"
      - "off" #Turns the AC off - Should be in quotes
      # Some devices have "auto" and "fan_only" switched. If the following two lines are uncommented, "auto" and "fan" shoud be commented out
      #- "auto_fan_only" #if remote shows fan but tasmota says auto
      #- "fan_only_auto" #if remote shows auto but tasmota says fan
    supported_fan_speeds:
      # Some devices say max,but it is high, and auto which is max. If you uncomment the following two, you have to comment high and max
      # - "auto_max" #woud become max
      # - "max_high" #would become high
      #- "on"
      #- "off"
      - "auto"
      - "min"
      - "low"
      - "medium"
      - "high"
      - "max"
    supported_swing_list:
      #- "off"
      - "vertical" #up to down
      - "horizontal" # Left to right
      #- "both"
    default_quiet_mode: "Off" #Quiet und Turbo sind in der Firmware vertauscht | optional - default "Off" string value
    default_turbo_mode: "On" #Quiet und Turbo sind in der Firmware vertauscht | optional - default "Off" string value
    default_econo_mode: "On" #optional - default "Off" string value
    hvac_model: "2" #optional - default "1" string value
    celsius_mode: "On" #optional - default "On" string value
    default_light_mode: "Off" #optional - default "Off" string value
    default_filter_mode: "Off" #optional - default "Off" string value
    default_clean_mode: "Off" #optional - default "Off" string value
    default_beep_mode: "Off" #optional - default "Off" string value
    default_sleep_mode: "-1" #optional - default "-1" string value
    default_swingv: "high" #optional - default "" string value
    default_swingh: "left" #optional - default "" string value 
    keep_mode_when_off: True #optional - default False boolean value : Must be True for MITSUBISHI_AC, ECOCLIM, etc.

`

hristo-atanasov / Tasmota-IRHVAC

Some Optimizations #104