Closed xiaoxia625 closed 2 years ago
root@onecloud:~# iperf3 -c 192.168.31.53 -F /dev/zero
Connecting to host 192.168.31.53, port 5201
[ 5] local 192.168.31.153 port 59334 connected to 192.168.31.53 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 11.6 MBytes 97.5 Mbits/sec 9 74.9 KBytes
[ 5] 1.00-2.00 sec 9.57 MBytes 80.3 Mbits/sec 1 116 KBytes
[ 5] 2.00-3.00 sec 10.4 MBytes 87.6 Mbits/sec 8 79.2 KBytes
[ 5] 3.00-4.00 sec 11.4 MBytes 95.4 Mbits/sec 3 84.8 KBytes
[ 5] 4.00-5.00 sec 11.1 MBytes 92.8 Mbits/sec 5 77.8 KBytes
[ 5] 5.00-6.00 sec 11.2 MBytes 94.3 Mbits/sec 2 106 KBytes
[ 5] 6.00-7.00 sec 11.2 MBytes 93.8 Mbits/sec 2 94.7 KBytes
[ 5] 7.00-8.00 sec 10.9 MBytes 91.2 Mbits/sec 0 127 KBytes
[ 5] 8.00-9.00 sec 10.7 MBytes 89.7 Mbits/sec 10 65.0 KBytes
[ 5] 9.00-10.00 sec 11.2 MBytes 93.8 Mbits/sec 3 65.0 KBytes
[ ID] Interval Transfer Bitrate Retr [ 5] 0.00-10.00 sec 109 MBytes 91.6 Mbits/sec 43 sender Sent 109 MByte / 0.00 Byte (100%) of /dev/zero [ 5] 0.00-10.00 sec 109 MBytes 91.3 Mbits/sec receiver
iperf Done.
挺奇怪的,采用这种固定数据的方式测速就正常了。但实际在使用中内网访问速率只有4M左右,下载速率10M左右。
问题更新 玩客云网口只有靠近USB端口那个灯亮,颜色为黄色,另一个灯不亮。家里宽带是500M的,路由器是红米AC2100,千兆端口。另外,ssh显示玩客云网卡是全双工、1000M速率的。 root@onecloud:~# ethtool eth0 Settings for eth0: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: Symmetric Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: on master-slave cfg: preferred slave master-slave status: slave Port: Twisted Pair PHYAD: 0 Transceiver: external MDI-X: Unknown Supports Wake-on: ug Wake-on: d Current message level: 0x0000003f (63) drv probe link timer ifdown ifup Link detected: yes
玩客云网口只有靠近USB端口那个灯亮,颜色为黄色,另一个灯不亮。
网卡灯无法反映什么。RTL8211默认配置下,LED灯知识与常规不一样。我没有添加调整LED的patch。
100M局域网内上下行速率差异较大
速度问题 #2 提了,就不留多个issue了。
C:\Users\root\Desktop\iperf-3.1.3-win64>iperf3 -c 192.168.31.153 Connecting to host 192.168.31.153, port 5201 [ 4] local 192.168.31.53 port 61749 connected to 192.168.31.153 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.01 sec 9.50 MBytes 78.7 Mbits/sec [ 4] 1.01-2.00 sec 9.62 MBytes 81.8 Mbits/sec [ 4] 2.00-3.00 sec 10.0 MBytes 83.9 Mbits/sec [ 4] 3.00-4.00 sec 11.2 MBytes 94.4 Mbits/sec [ 4] 4.00-5.00 sec 11.4 MBytes 95.4 Mbits/sec [ 4] 5.00-6.00 sec 10.5 MBytes 88.1 Mbits/sec [ 4] 6.00-7.00 sec 11.4 MBytes 95.4 Mbits/sec [ 4] 7.00-8.00 sec 10.6 MBytes 89.1 Mbits/sec [ 4] 8.00-9.00 sec 11.2 MBytes 94.4 Mbits/sec [ 4] 9.00-10.00 sec 11.4 MBytes 95.4 Mbits/sec
[ ID] Interval Transfer Bandwidth [ 4] 0.00-10.00 sec 107 MBytes 89.6 Mbits/sec sender [ 4] 0.00-10.00 sec 107 MBytes 89.6 Mbits/sec receiver
iperf Done.
C:\Users\root\Desktop\iperf-3.1.3-win64>iperf3 -c 192.168.31.153 -R Connecting to host 192.168.31.153, port 5201 Reverse mode, remote host 192.168.31.153 is sending [ 4] local 192.168.31.53 port 61771 connected to 192.168.31.153 port 5201 [ ID] Interval Transfer Bandwidth [ 4] 0.00-1.07 sec 5.04 MBytes 39.5 Mbits/sec [ 4] 1.07-2.00 sec 2.94 MBytes 26.5 Mbits/sec [ 4] 2.00-3.00 sec 4.22 MBytes 35.4 Mbits/sec [ 4] 3.00-4.00 sec 1.55 MBytes 13.0 Mbits/sec [ 4] 4.00-5.00 sec 3.74 MBytes 31.4 Mbits/sec [ 4] 5.00-6.00 sec 5.53 MBytes 46.4 Mbits/sec [ 4] 6.00-7.00 sec 3.93 MBytes 32.9 Mbits/sec [ 4] 7.00-8.00 sec 3.57 MBytes 29.9 Mbits/sec [ 4] 8.00-9.00 sec 3.54 MBytes 29.7 Mbits/sec [ 4] 9.00-10.00 sec 5.23 MBytes 43.9 Mbits/sec
[ ID] Interval Transfer Bandwidth Retr [ 4] 0.00-10.00 sec 39.5 MBytes 33.1 Mbits/sec 771 sender [ 4] 0.00-10.00 sec 39.3 MBytes 33.0 Mbits/sec receiver
iperf Done.