sensei-hacker
commented
3 months ago You wrote "my rx is wired to UART4". Your screenshot shows it's configured for rx on UART2.
Open MBR595 opened 3 months ago
sensei-hacker
commented
3 months ago You wrote "my rx is wired to UART4". Your screenshot shows it's configured for rx on UART2.
MBR595
commented
2 months ago Hello,
It may be connected to UART 4. The writing on the board is very small. Assuming it's connected to UART 2, it's still not recognizing the RX. Any suggestions?
From: Sensei @.> Sent: Sunday, July 7, 2024 11:11 PM To: iNavFlight/inav-configurator @.> Cc: MBR595 @.>; Author @.> Subject: Re: [iNavFlight/inav-configurator] MATEK F405 v1 (Issue #2141)
You wrote "my rx is wired to UART4". Your screenshot shows it's configured for rx on UART2.
— Reply to this email directly, view it on GitHubhttps://github.com/iNavFlight/inav-configurator/issues/2141#issuecomment-2212900063, or unsubscribehttps://github.com/notifications/unsubscribe-auth/AEMX4UWZ45Q25PSW3LDZNSDZLH7OXAVCNFSM6AAAAABKPV4D46VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDEMJSHEYDAMBWGM. You are receiving this because you authored the thread.Message ID: @.***>
sensei-hacker
commented
2 months ago In your shoes, the first thing I would do is use some good lighting and take a close-up picture with my phone. Then zoom in on that pic to a) verify which user it is on and b) check for any stray wire strands, solder whiskers, etc.
If it's not connected to the same uart that is configured, that would be the problem. So I would start there.
MBR595
commented
2 months ago Good Afternoon,
I inspected the board again. The RX is plugged in to UART4 and the GPS is plugged into UART 2. What should I do?
From: Sensei @.> Sent: Monday, July 8, 2024 1:30 PM To: iNavFlight/inav-configurator @.> Cc: MBR595 @.>; Author @.> Subject: Re: [iNavFlight/inav-configurator] MATEK F405 v1 (Issue #2141)
In your shoes, the first thing I would do is use some good lighting and take a close-up picture with my phone. Then zoom in on that pic to a) verify which user it is on and b) check for any stray wire strands, solder whiskers, etc.
If it's not connected to the same uart that is configured, that would be the problem. So I would start there.
— Reply to this email directly, view it on GitHubhttps://github.com/iNavFlight/inav-configurator/issues/2141#issuecomment-2214782342, or unsubscribehttps://github.com/notifications/unsubscribe-auth/AEMX4UQAFSLEIJGIFHLYXFTZLLECZAVCNFSM6AAAAABKPV4D46VHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDEMJUG44DEMZUGI. You are receiving this because you authored the thread.Message ID: @.***>
Hello,
I recently changed controllers. Currently using a FRSKY TARANIS X-LITE PRO with the TBS module and receiver. I'm using a Matke F405 V1 board and INAV Configurator 7.1.1. FW is 7.1.0 MATEKF450SE. My RX is wired to UART4 but it's not being recognized in the configurator when I turn it on, save and reboot. Any advice you can offer is greatly appreciated.