Turning on my plane system in the garden (no compass, HGLRC GPS), I found that orientation at power on time is important.
One thing I found though, was that the fake compass/GPS only heading assumes plane is turned on facing north.
When turned on facing south, and walking south, distance kept increasing, but home pointer pointed forward away from target (tested up to 20m walk). Turning and walking towards target, it point 180 degrees off again.
Same for east/west facing during power. home pointer started rotated wrong way - 90 degrees. Passing home point, it turned around, so it has good knowledge of home, just a pointer pointing the wrong way.
This was all walking speed. Config below. If this is assumption because no compass, why not learn real orientation after x meters of motion, using GPS.
set looptime = 2000
set gyro_sync = ON
set align_gyro = DEFAULT
set gyro_hardware_lpf = 188HZ
set gyro_lpf_hz = 60
set moron_threshold = 32
set gyro_notch1_hz = 0
set gyro_notch1_cutoff = 1
set gyro_notch2_hz = 0
set gyro_notch2_cutoff = 1
set vbat_adc_channel = 2
set rssi_adc_channel = 3
set current_adc_channel = 1
set airspeed_adc_channel = 0
set acc_notch_hz = 0
set acc_notch_cutoff = 1
set align_acc = DEFAULT
set acc_hardware = MPU6000
set acc_lpf_hz = 15
set acczero_x = 172
set acczero_y = -84
set acczero_z = -196
set accgain_x = 4102
set accgain_y = 4081
set accgain_z = 4025
set rangefinder_hardware = NONE
set rangefinder_median_filter = OFF
set align_mag = DEFAULT
set mag_hardware = NONE
set mag_declination = 0
set magzero_x = 0
set magzero_y = 0
set magzero_z = 0
set mag_calibration_time = 30
set align_mag_roll = 0
set align_mag_pitch = 0
set align_mag_yaw = 0
set baro_hardware = BMP280
set baro_median_filter = ON
set pitot_hardware = NONE
set pitot_use_median_filter = ON
set pitot_noise_lpf = 0.600
set pitot_scale = 1.000
set receiver_type = SERIAL
set mid_rc = 1500
set min_check = 1100
set max_check = 1900
set rssi_channel = 10
set rssi_scale = 100
set rssi_invert = OFF
set rc_smoothing = ON
set serialrx_provider = IBUS
set serialrx_inverted = OFF
set rx_spi_rf_channel_count = 0
set spektrum_sat_bind = 0
set rx_min_usec = 885
set rx_max_usec = 2115
set serialrx_halfduplex = OFF
set blackbox_rate_num = 3
set blackbox_rate_denom = 4
set blackbox_device = SDCARD
set sdcard_detect_inverted = ON
set min_throttle = 1150
set max_throttle = 1850
set min_command = 1000
set motor_pwm_rate = 400
set motor_pwm_protocol = STANDARD
set failsafe_delay = 5
set failsafe_recovery_delay = 5
set failsafe_off_delay = 200
set failsafe_throttle = 1000
set failsafe_throttle_low_delay = 0
set failsafe_procedure = RTH
set failsafe_stick_threshold = 50
set failsafe_fw_roll_angle = -200
set failsafe_fw_pitch_angle = 100
set failsafe_fw_yaw_rate = -45
set failsafe_min_distance = 0
set failsafe_min_distance_procedure = DROP
set align_board_roll = 0
set align_board_pitch = -28
set align_board_yaw = 0
set gimbal_mode = NORMAL
set vbat_scale = 1100
set vbat_max_cell_voltage = 420
set vbat_min_cell_voltage = 330
set vbat_warning_cell_voltage = 350
set battery_capacity = 0
set battery_capacity_warning = 0
set battery_capacity_critical = 0
set battery_capacity_unit = MAH
set current_meter_scale = 265
set current_meter_offset = 0
set current_meter_type = ADC
set yaw_motor_direction = 1
set yaw_jump_prevention_limit = 200
set 3d_deadband_low = 1406
set 3d_deadband_high = 1514
set 3d_neutral = 1460
set servo_center_pulse = 1500
set servo_pwm_rate = 50
set servo_lpf_hz = 20
set flaperon_throw_offset = 200
set tri_unarmed_servo = ON
set reboot_character = 82
set imu_dcm_kp = 2500
set imu_dcm_ki = 50
set imu_dcm_kp_mag = 10000
set imu_dcm_ki_mag = 0
set small_angle = 180
set fixed_wing_auto_arm = OFF
set disarm_kill_switch = ON
set auto_disarm_delay = 5
set gps_provider = UBLOX
set gps_sbas_mode = AUTO
set gps_dyn_model = AIR_1G
set gps_auto_config = ON
set gps_auto_baud = ON
set gps_ublox_use_galileo = OFF
set gps_min_sats = 6
set deadband = 5
set yaw_deadband = 5
set pos_hold_deadband = 20
set alt_hold_deadband = 50
set 3d_deadband_throttle = 50
set fw_autotune_overshoot_time = 100
set fw_autotune_undershoot_time = 200
set fw_autotune_threshold = 50
set fw_autotune_ff_to_p_gain = 10
set fw_autotune_ff_to_i_tc = 600
set inav_auto_mag_decl = ON
set inav_gravity_cal_tolerance = 5
set inav_use_gps_velned = ON
set inav_reset_altitude = FIRST_ARM
set inav_max_surface_altitude = 200
set inav_w_z_surface_p = 3.500
set inav_w_z_surface_v = 6.100
set inav_w_z_baro_p = 0.350
set inav_w_z_gps_p = 0.200
set inav_w_z_gps_v = 0.500
set inav_w_xy_gps_p = 1.000
set inav_w_xy_gps_v = 2.000
set inav_w_z_res_v = 0.500
set inav_w_xy_res_v = 0.500
set inav_w_acc_bias = 0.010
set inav_max_eph_epv = 1000.000
set inav_baro_epv = 100.000
set nav_disarm_on_landing = OFF
set nav_use_midthr_for_althold = OFF
set nav_extra_arming_safety = OFF
set nav_user_control_mode = ATTI
set nav_position_timeout = 5
set nav_wp_radius = 100
set nav_wp_safe_distance = 10000
set nav_auto_speed = 2500
set nav_auto_climb_rate = 500
set nav_manual_speed = 3000
set nav_manual_climb_rate = 200
set nav_landing_speed = 200
set nav_land_slowdown_minalt = 500
set nav_land_slowdown_maxalt = 2000
set nav_emerg_landing_speed = 500
set nav_min_rth_distance = 500
set nav_rth_climb_first = ON
set nav_rth_climb_ignore_emerg = OFF
set nav_rth_tail_first = OFF
set nav_rth_allow_landing = NEVER
set nav_rth_alt_mode = AT_LEAST
set nav_rth_abort_threshold = 50000
set nav_rth_altitude = 3500
set nav_mc_bank_angle = 30
set nav_mc_hover_thr = 1500
set nav_mc_auto_disarm_delay = 2000
set nav_fw_cruise_thr = 1400
set nav_fw_min_thr = 1200
set nav_fw_max_thr = 1700
set nav_fw_bank_angle = 20
set nav_fw_climb_angle = 20
set nav_fw_dive_angle = 15
set nav_fw_pitch2thr = 10
set nav_fw_loiter_radius = 5000
set nav_fw_land_dive_angle = 2
set nav_fw_launch_velocity = 300
set nav_fw_launch_accel = 1863
set nav_fw_launch_max_angle = 45
set nav_fw_launch_detect_time = 40
set nav_fw_launch_thr = 1700
set nav_fw_launch_idle_thr = 1000
set nav_fw_launch_motor_delay = 500
set nav_fw_launch_spinup_time = 100
set nav_fw_launch_min_time = 0
set nav_fw_launch_timeout = 5000
set nav_fw_launch_max_altitude = 0
set nav_fw_launch_climb_angle = 18
set telemetry_switch = OFF
set telemetry_inverted = OFF
set frsky_default_latitude = 0.000
set frsky_default_longitude = 0.000
set frsky_coordinates_format = 0
set frsky_unit = METRIC
set frsky_vfas_precision = 0
set report_cell_voltage = OFF
set hott_alarm_sound_interval = 5
set smartport_uart_unidir = OFF
set smartport_fuel_unit = MAH
set ibus_telemetry_type = 0
set ltm_update_rate = NORMAL
set ledstrip_visual_beeper = OFF
set osd_video_system = 0
set osd_row_shiftdown = 0
set osd_units = METRIC
set osd_stats_energy_unit = MAH
set osd_rssi_alarm = 20
set osd_time_alarm = 10
set osd_alt_alarm = 100
set osd_artificial_horizon_reverse_roll = OFF
set osd_crosshairs_style = DEFAULT
set osd_left_sidebar_scroll = NONE
set osd_right_sidebar_scroll = NONE
set osd_sidebar_scroll_arrows = OFF
set osd_main_voltage_pos = 2092
set osd_main_voltage_decimals = 1
set osd_rssi_pos = 2433
set osd_flytimer_pos = 311
set osd_ontime_pos = 279
set osd_flymode_pos = 2444
set osd_throttle_pos = 2113
set osd_vtx_channel_pos = 200
set osd_crosshairs_pos = 2048
set osd_artificial_horizon_pos = 2248
set osd_horizon_sidebars_pos = 2248
set osd_current_draw_pos = 2145
set osd_mah_drawn_pos = 2177
set osd_wh_drawn_pos = 161
set osd_bat_remaining_capacity_pos = 193
set osd_bat_remaining_percent_pos = 225
set osd_craft_name_pos = 84
set osd_gps_speed_pos = 2103
set osd_gps_sats_pos = 2400
set osd_gps_lon_pos = 2063
set osd_gps_lat_pos = 2052
set osd_home_dir_pos = 2414
set osd_home_dist_pos = 2081
set osd_altitude_pos = 2135
set osd_vario_pos = 2231
set osd_vario_num_pos = 2296
set osd_pid_roll_pos = 322
set osd_pid_pitch_pos = 354
set osd_pid_yaw_pos = 386
set osd_power_pos = 47
set osd_air_speed_pos = 163
set osd_ontime_flytime_pos = 2423
set osd_rtc_time_pos = 407
set osd_messages_pos = 2465
set osd_gps_hdop_pos = 320
set osd_main_cell_voltage_pos = 44
set osd_throttle_auto_thr_pos = 70
set osd_heading_graph_pos = 82
set osd_efficiency_mah_pos = 161
set osd_efficiency_wh_pos = 161
set i2c_speed = 400KHZ
set debug_mode = NONE
set acc_task_frequency = 500
set attitude_task_frequency = 250
set async_mode = NONE
set throttle_tilt_comp_str = 0
set input_filtering_mode = OFF
set mode_range_logic_operator = OR
set stats = OFF
set stats_total_time = 0
set stats_total_dist = 0
set stats_total_energy = 0
set tz_offset = 0
set display_force_sw_blink = OFF
profile
profile 1
set mc_p_pitch = 40
set mc_i_pitch = 30
set mc_d_pitch = 23
set mc_p_roll = 40
set mc_i_roll = 30
set mc_d_roll = 23
set mc_p_yaw = 85
set mc_i_yaw = 45
set mc_d_yaw = 0
set mc_p_level = 20
set mc_i_level = 15
set mc_d_level = 75
set fw_p_pitch = 20
set fw_i_pitch = 30
set fw_ff_pitch = 15
set fw_p_roll = 20
set fw_i_roll = 30
set fw_ff_roll = 15
set fw_p_yaw = 45
set fw_i_yaw = 5
set fw_ff_yaw = 15
set fw_p_level = 20
set fw_i_level = 5
set fw_d_level = 75
set max_angle_inclination_rll = 600
set max_angle_inclination_pit = 600
set dterm_lpf_hz = 40
set yaw_lpf_hz = 30
set dterm_setpoint_weight = 0.000
set fw_iterm_throw_limit = 165
set fw_reference_airspeed = 1000.000
set fw_turn_assist_yaw_gain = 1.000
set dterm_notch_hz = 0
set dterm_notch_cutoff = 1
set pidsum_limit = 500
set yaw_p_limit = 300
set iterm_ignore_threshold = 200
set yaw_iterm_ignore_threshold = 50
set rate_accel_limit_roll_pitch = 0
set rate_accel_limit_yaw = 10000
set heading_hold_rate_limit = 90
set nav_mc_pos_z_p = 50
set nav_mc_pos_z_i = 0
set nav_mc_pos_z_d = 0
set nav_mc_vel_z_p = 100
set nav_mc_vel_z_i = 50
set nav_mc_vel_z_d = 10
set nav_mc_pos_xy_p = 65
set nav_mc_pos_xy_i = 120
set nav_mc_pos_xy_d = 10
set nav_mc_vel_xy_p = 40
set nav_mc_vel_xy_i = 15
set nav_mc_vel_xy_d = 100
set nav_mc_heading_p = 60
set nav_fw_pos_z_p = 50
set nav_fw_pos_z_i = 0
set nav_fw_pos_z_d = 0
set nav_fw_pos_xy_p = 75
set nav_fw_pos_xy_i = 5
set nav_fw_pos_xy_d = 8
set nav_fw_heading_p = 60
set thr_mid = 50
set thr_expo = 0
set tpa_rate = 0
set tpa_breakpoint = 1500
set fw_tpa_time_constant = 0
set rc_expo = 70
set rc_yaw_expo = 20
set roll_rate = 20
set pitch_rate = 15
set yaw_rate = 9
set manual_rc_expo = 70
set manual_rc_yaw_expo = 20
set manual_roll_rate = 100
set manual_pitch_rate = 100
set manual_yaw_rate = 100`
With GPS only (no compass) heading is acquired when speed exceeds 3 m/s (running speed), before that heading is assumed to be North at power up. Try running with your plane
Turning on my plane system in the garden (no compass, HGLRC GPS), I found that orientation at power on time is important.
One thing I found though, was that the fake compass/GPS only heading assumes plane is turned on facing north. When turned on facing south, and walking south, distance kept increasing, but home pointer pointed forward away from target (tested up to 20m walk). Turning and walking towards target, it point 180 degrees off again. Same for east/west facing during power. home pointer started rotated wrong way - 90 degrees. Passing home point, it turned around, so it has good knowledge of home, just a pointer pointing the wrong way.
This was all walking speed. Config below. If this is assumption because no compass, why not learn real orientation after x meters of motion, using GPS.
`# dump
version
INAV/OMNIBUSF4PRO 1.9.1 Apr 21 2018 / 13:12:44 (03a5c1922)
resources
mixer
mixer AIRPLANE
mmix reset
servo mix
smix reset
servo
servo 0 1000 2000 1500 100 -1 servo 1 1000 2000 1500 100 -1 servo 2 1000 2000 1575 100 -1 servo 3 1000 2000 1469 -100 -1 servo 4 1000 2000 1469 -100 -1 servo 5 1000 2000 1597 100 -1 servo 6 1000 2000 1500 100 -1 servo 7 1000 2000 1500 100 -1
feature
feature -RX_PPM feature -VBAT feature -TX_PROF_SEL feature -MOTOR_STOP feature -SERVO_TILT feature -SOFTSERIAL feature -GPS feature -TELEMETRY feature -CURRENT_METER feature -3D feature -RX_PARALLEL_PWM feature -RX_MSP feature -RSSI_ADC feature -LED_STRIP feature -DASHBOARD feature -BLACKBOX feature -CHANNEL_FORWARDING feature -TRANSPONDER feature -AIRMODE feature -SUPEREXPO feature -VTX feature -RX_SPI feature -PWM_SERVO_DRIVER feature -PWM_OUTPUT_ENABLE feature -OSD feature -FW_LAUNCH feature -TRACE feature VBAT feature TX_PROF_SEL feature MOTOR_STOP feature GPS feature BLACKBOX feature AIRMODE feature PWM_OUTPUT_ENABLE feature OSD
beeper
beeper RUNTIME_CALIBRATION ... beeper CAM_CONNECTION_CLOSED
map
map AETR
name
name -
serial
serial 20 1 115200 38400 0 115200 serial 0 1 115200 38400 0 115200 serial 2 2 115200 38400 0 115200 serial 5 64 115200 38400 0 115200
led
led 0 0,0::C:0 ... led 31 0,0::C:0
color
color 0 0,0,0 ... mode_color 6 10 0
aux
aux 0 0 1 1500 2100 aux 1 1 3 950 1100 aux 2 3 3 1500 1700 aux 3 9 3 1475 1700 aux 4 8 3 1900 2100 aux 5 10 3 1300 1500 aux 6 27 4 1900 2100 aux 7 0 0 900 900 aux 8 0 0 900 900 aux 9 0 0 900 900 aux 10 0 0 900 900 aux 11 0 0 900 900 aux 12 0 0 900 900 aux 13 0 0 900 900 aux 14 0 0 900 900 aux 15 0 0 900 900 aux 16 0 0 900 900 aux 17 0 0 900 900 aux 18 0 0 900 900 aux 19 0 0 900 900
adjrange
adjrange 0 0 0 900 900 0 0 adjrange 1 0 0 900 900 0 0 adjrange 2 0 0 900 900 0 0 adjrange 3 0 0 900 900 0 0 adjrange 4 0 0 900 900 0 0 adjrange 5 0 0 900 900 0 0 adjrange 6 0 0 900 900 0 0 adjrange 7 0 0 900 900 0 0 adjrange 8 0 0 900 900 0 0 adjrange 9 0 0 900 900 0 0 adjrange 10 0 0 900 900 0 0 adjrange 11 0 0 900 900 0 0
rxrange
rxrange 0 1000 2000 rxrange 1 1000 2000 rxrange 2 1000 2000 rxrange 3 1000 2000
master
set looptime = 2000 set gyro_sync = ON set align_gyro = DEFAULT set gyro_hardware_lpf = 188HZ set gyro_lpf_hz = 60 set moron_threshold = 32 set gyro_notch1_hz = 0 set gyro_notch1_cutoff = 1 set gyro_notch2_hz = 0 set gyro_notch2_cutoff = 1 set vbat_adc_channel = 2 set rssi_adc_channel = 3 set current_adc_channel = 1 set airspeed_adc_channel = 0 set acc_notch_hz = 0 set acc_notch_cutoff = 1 set align_acc = DEFAULT set acc_hardware = MPU6000 set acc_lpf_hz = 15 set acczero_x = 172 set acczero_y = -84 set acczero_z = -196 set accgain_x = 4102 set accgain_y = 4081 set accgain_z = 4025 set rangefinder_hardware = NONE set rangefinder_median_filter = OFF set align_mag = DEFAULT set mag_hardware = NONE set mag_declination = 0 set magzero_x = 0 set magzero_y = 0 set magzero_z = 0 set mag_calibration_time = 30 set align_mag_roll = 0 set align_mag_pitch = 0 set align_mag_yaw = 0 set baro_hardware = BMP280 set baro_median_filter = ON set pitot_hardware = NONE set pitot_use_median_filter = ON set pitot_noise_lpf = 0.600 set pitot_scale = 1.000 set receiver_type = SERIAL set mid_rc = 1500 set min_check = 1100 set max_check = 1900 set rssi_channel = 10 set rssi_scale = 100 set rssi_invert = OFF set rc_smoothing = ON set serialrx_provider = IBUS set serialrx_inverted = OFF set rx_spi_rf_channel_count = 0 set spektrum_sat_bind = 0 set rx_min_usec = 885 set rx_max_usec = 2115 set serialrx_halfduplex = OFF set blackbox_rate_num = 3 set blackbox_rate_denom = 4 set blackbox_device = SDCARD set sdcard_detect_inverted = ON set min_throttle = 1150 set max_throttle = 1850 set min_command = 1000 set motor_pwm_rate = 400 set motor_pwm_protocol = STANDARD set failsafe_delay = 5 set failsafe_recovery_delay = 5 set failsafe_off_delay = 200 set failsafe_throttle = 1000 set failsafe_throttle_low_delay = 0 set failsafe_procedure = RTH set failsafe_stick_threshold = 50 set failsafe_fw_roll_angle = -200 set failsafe_fw_pitch_angle = 100 set failsafe_fw_yaw_rate = -45 set failsafe_min_distance = 0 set failsafe_min_distance_procedure = DROP set align_board_roll = 0 set align_board_pitch = -28 set align_board_yaw = 0 set gimbal_mode = NORMAL set vbat_scale = 1100 set vbat_max_cell_voltage = 420 set vbat_min_cell_voltage = 330 set vbat_warning_cell_voltage = 350 set battery_capacity = 0 set battery_capacity_warning = 0 set battery_capacity_critical = 0 set battery_capacity_unit = MAH set current_meter_scale = 265 set current_meter_offset = 0 set current_meter_type = ADC set yaw_motor_direction = 1 set yaw_jump_prevention_limit = 200 set 3d_deadband_low = 1406 set 3d_deadband_high = 1514 set 3d_neutral = 1460 set servo_center_pulse = 1500 set servo_pwm_rate = 50 set servo_lpf_hz = 20 set flaperon_throw_offset = 200 set tri_unarmed_servo = ON set reboot_character = 82 set imu_dcm_kp = 2500 set imu_dcm_ki = 50 set imu_dcm_kp_mag = 10000 set imu_dcm_ki_mag = 0 set small_angle = 180 set fixed_wing_auto_arm = OFF set disarm_kill_switch = ON set auto_disarm_delay = 5 set gps_provider = UBLOX set gps_sbas_mode = AUTO set gps_dyn_model = AIR_1G set gps_auto_config = ON set gps_auto_baud = ON set gps_ublox_use_galileo = OFF set gps_min_sats = 6 set deadband = 5 set yaw_deadband = 5 set pos_hold_deadband = 20 set alt_hold_deadband = 50 set 3d_deadband_throttle = 50 set fw_autotune_overshoot_time = 100 set fw_autotune_undershoot_time = 200 set fw_autotune_threshold = 50 set fw_autotune_ff_to_p_gain = 10 set fw_autotune_ff_to_i_tc = 600 set inav_auto_mag_decl = ON set inav_gravity_cal_tolerance = 5 set inav_use_gps_velned = ON set inav_reset_altitude = FIRST_ARM set inav_max_surface_altitude = 200 set inav_w_z_surface_p = 3.500 set inav_w_z_surface_v = 6.100 set inav_w_z_baro_p = 0.350 set inav_w_z_gps_p = 0.200 set inav_w_z_gps_v = 0.500 set inav_w_xy_gps_p = 1.000 set inav_w_xy_gps_v = 2.000 set inav_w_z_res_v = 0.500 set inav_w_xy_res_v = 0.500 set inav_w_acc_bias = 0.010 set inav_max_eph_epv = 1000.000 set inav_baro_epv = 100.000 set nav_disarm_on_landing = OFF set nav_use_midthr_for_althold = OFF set nav_extra_arming_safety = OFF set nav_user_control_mode = ATTI set nav_position_timeout = 5 set nav_wp_radius = 100 set nav_wp_safe_distance = 10000 set nav_auto_speed = 2500 set nav_auto_climb_rate = 500 set nav_manual_speed = 3000 set nav_manual_climb_rate = 200 set nav_landing_speed = 200 set nav_land_slowdown_minalt = 500 set nav_land_slowdown_maxalt = 2000 set nav_emerg_landing_speed = 500 set nav_min_rth_distance = 500 set nav_rth_climb_first = ON set nav_rth_climb_ignore_emerg = OFF set nav_rth_tail_first = OFF set nav_rth_allow_landing = NEVER set nav_rth_alt_mode = AT_LEAST set nav_rth_abort_threshold = 50000 set nav_rth_altitude = 3500 set nav_mc_bank_angle = 30 set nav_mc_hover_thr = 1500 set nav_mc_auto_disarm_delay = 2000 set nav_fw_cruise_thr = 1400 set nav_fw_min_thr = 1200 set nav_fw_max_thr = 1700 set nav_fw_bank_angle = 20 set nav_fw_climb_angle = 20 set nav_fw_dive_angle = 15 set nav_fw_pitch2thr = 10 set nav_fw_loiter_radius = 5000 set nav_fw_land_dive_angle = 2 set nav_fw_launch_velocity = 300 set nav_fw_launch_accel = 1863 set nav_fw_launch_max_angle = 45 set nav_fw_launch_detect_time = 40 set nav_fw_launch_thr = 1700 set nav_fw_launch_idle_thr = 1000 set nav_fw_launch_motor_delay = 500 set nav_fw_launch_spinup_time = 100 set nav_fw_launch_min_time = 0 set nav_fw_launch_timeout = 5000 set nav_fw_launch_max_altitude = 0 set nav_fw_launch_climb_angle = 18 set telemetry_switch = OFF set telemetry_inverted = OFF set frsky_default_latitude = 0.000 set frsky_default_longitude = 0.000 set frsky_coordinates_format = 0 set frsky_unit = METRIC set frsky_vfas_precision = 0 set report_cell_voltage = OFF set hott_alarm_sound_interval = 5 set smartport_uart_unidir = OFF set smartport_fuel_unit = MAH set ibus_telemetry_type = 0 set ltm_update_rate = NORMAL set ledstrip_visual_beeper = OFF set osd_video_system = 0 set osd_row_shiftdown = 0 set osd_units = METRIC set osd_stats_energy_unit = MAH set osd_rssi_alarm = 20 set osd_time_alarm = 10 set osd_alt_alarm = 100 set osd_artificial_horizon_reverse_roll = OFF set osd_crosshairs_style = DEFAULT set osd_left_sidebar_scroll = NONE set osd_right_sidebar_scroll = NONE set osd_sidebar_scroll_arrows = OFF set osd_main_voltage_pos = 2092 set osd_main_voltage_decimals = 1 set osd_rssi_pos = 2433 set osd_flytimer_pos = 311 set osd_ontime_pos = 279 set osd_flymode_pos = 2444 set osd_throttle_pos = 2113 set osd_vtx_channel_pos = 200 set osd_crosshairs_pos = 2048 set osd_artificial_horizon_pos = 2248 set osd_horizon_sidebars_pos = 2248 set osd_current_draw_pos = 2145 set osd_mah_drawn_pos = 2177 set osd_wh_drawn_pos = 161 set osd_bat_remaining_capacity_pos = 193 set osd_bat_remaining_percent_pos = 225 set osd_craft_name_pos = 84 set osd_gps_speed_pos = 2103 set osd_gps_sats_pos = 2400 set osd_gps_lon_pos = 2063 set osd_gps_lat_pos = 2052 set osd_home_dir_pos = 2414 set osd_home_dist_pos = 2081 set osd_altitude_pos = 2135 set osd_vario_pos = 2231 set osd_vario_num_pos = 2296 set osd_pid_roll_pos = 322 set osd_pid_pitch_pos = 354 set osd_pid_yaw_pos = 386 set osd_power_pos = 47 set osd_air_speed_pos = 163 set osd_ontime_flytime_pos = 2423 set osd_rtc_time_pos = 407 set osd_messages_pos = 2465 set osd_gps_hdop_pos = 320 set osd_main_cell_voltage_pos = 44 set osd_throttle_auto_thr_pos = 70 set osd_heading_graph_pos = 82 set osd_efficiency_mah_pos = 161 set osd_efficiency_wh_pos = 161 set i2c_speed = 400KHZ set debug_mode = NONE set acc_task_frequency = 500 set attitude_task_frequency = 250 set async_mode = NONE set throttle_tilt_comp_str = 0 set input_filtering_mode = OFF set mode_range_logic_operator = OR set stats = OFF set stats_total_time = 0 set stats_total_dist = 0 set stats_total_energy = 0 set tz_offset = 0 set display_force_sw_blink = OFF
profile
profile 1
set mc_p_pitch = 40 set mc_i_pitch = 30 set mc_d_pitch = 23 set mc_p_roll = 40 set mc_i_roll = 30 set mc_d_roll = 23 set mc_p_yaw = 85 set mc_i_yaw = 45 set mc_d_yaw = 0 set mc_p_level = 20 set mc_i_level = 15 set mc_d_level = 75 set fw_p_pitch = 20 set fw_i_pitch = 30 set fw_ff_pitch = 15 set fw_p_roll = 20 set fw_i_roll = 30 set fw_ff_roll = 15 set fw_p_yaw = 45 set fw_i_yaw = 5 set fw_ff_yaw = 15 set fw_p_level = 20 set fw_i_level = 5 set fw_d_level = 75 set max_angle_inclination_rll = 600 set max_angle_inclination_pit = 600 set dterm_lpf_hz = 40 set yaw_lpf_hz = 30 set dterm_setpoint_weight = 0.000 set fw_iterm_throw_limit = 165 set fw_reference_airspeed = 1000.000 set fw_turn_assist_yaw_gain = 1.000 set dterm_notch_hz = 0 set dterm_notch_cutoff = 1 set pidsum_limit = 500 set yaw_p_limit = 300 set iterm_ignore_threshold = 200 set yaw_iterm_ignore_threshold = 50 set rate_accel_limit_roll_pitch = 0 set rate_accel_limit_yaw = 10000 set heading_hold_rate_limit = 90 set nav_mc_pos_z_p = 50 set nav_mc_pos_z_i = 0 set nav_mc_pos_z_d = 0 set nav_mc_vel_z_p = 100 set nav_mc_vel_z_i = 50 set nav_mc_vel_z_d = 10 set nav_mc_pos_xy_p = 65 set nav_mc_pos_xy_i = 120 set nav_mc_pos_xy_d = 10 set nav_mc_vel_xy_p = 40 set nav_mc_vel_xy_i = 15 set nav_mc_vel_xy_d = 100 set nav_mc_heading_p = 60 set nav_fw_pos_z_p = 50 set nav_fw_pos_z_i = 0 set nav_fw_pos_z_d = 0 set nav_fw_pos_xy_p = 75 set nav_fw_pos_xy_i = 5 set nav_fw_pos_xy_d = 8 set nav_fw_heading_p = 60 set thr_mid = 50 set thr_expo = 0 set tpa_rate = 0 set tpa_breakpoint = 1500 set fw_tpa_time_constant = 0 set rc_expo = 70 set rc_yaw_expo = 20 set roll_rate = 20 set pitch_rate = 15 set yaw_rate = 9 set manual_rc_expo = 70 set manual_rc_yaw_expo = 20 set manual_roll_rate = 100 set manual_pitch_rate = 100 set manual_yaw_rate = 100`