search

iNavFlight / inav

INAV: Navigation-enabled flight control software
https://inavflight.github.io
GNU General Public License v3.0
3.08k stars 1.46k forks source link

Smart Audio not working over Soft Serial on F411 Wing FC with Cricket Pro V2.1 Vtx iNAV 2.0 #3951

Closed Nihilistic closed 5 years ago

Nihilistic commented 5 years ago

Current Behavior

Steps to Reproduce

1.Soldered white SA wire from Cricket to ST1 pad of F411 2.Enabled Soft Serial in Config tab of iNAV 3.Enabled TBS Smart Audio on Soft Serial in Ports tab of iNAV

  1. Attempted to configure Vtx settings via OSD stick menu, but all I see are dashes where there should be channel and power information.

Expected behavior

Should be able to set band and channel and power of the Cricket Pro v2.1 (and any other SA capable Vtx) over soft serial using SA.

Suggested solution(s)

Hopefully fix it? hehe...I think this issue may have lain unresolved since December 2017 (different FC though).

Additional context

version

INAV/MATEKF411 2.0.0 Aug 20 2018 / 19:23:35 (dbdd1656a)

resources

mixer

mmix reset

mmix 0 1.000 0.000 0.000 0.000

servo mix

smix reset

smix 0 3 0 50 0 smix 1 3 1 50 0 smix 2 4 0 -50 0 smix 3 4 1 50 0

servo

servo 0 1000 2000 1500 100 servo 1 1000 2000 1500 100 servo 2 1000 2000 1500 100 servo 3 1000 2000 1500 -100 servo 4 1000 2000 1500 100 servo 5 1000 2000 1500 100 servo 6 1000 2000 1500 100 servo 7 1000 2000 1500 100

feature

feature -THR_VBAT_COMP feature -VBAT feature -TX_PROF_SEL feature -BAT_PROF_AUTOSWITCH feature -MOTOR_STOP feature -SOFTSERIAL feature -GPS feature -TELEMETRY feature -CURRENT_METER feature -3D feature -RX_PARALLEL_PWM feature -RX_MSP feature -RSSI_ADC feature -LED_STRIP feature -DASHBOARD feature -BLACKBOX feature -TRANSPONDER feature -AIRMODE feature -SUPEREXPO feature -VTX feature -RX_SPI feature -PWM_SERVO_DRIVER feature -PWM_OUTPUT_ENABLE feature -OSD feature -FW_LAUNCH feature -TRACE feature VBAT feature TX_PROF_SEL feature MOTOR_STOP feature SOFTSERIAL feature GPS feature TELEMETRY feature CURRENT_METER feature AIRMODE feature PWM_OUTPUT_ENABLE feature OSD

beeper

beeper RUNTIME_CALIBRATION beeper HW_FAILURE beeper RX_LOST beeper RX_LOST_LANDING beeper DISARMING beeper ARMING beeper ARMING_GPS_FIX beeper BAT_CRIT_LOW beeper BAT_LOW beeper GPS_STATUS beeper RX_SET beeper ACTION_SUCCESS beeper ACTION_FAIL beeper READY_BEEP beeper MULTI_BEEPS beeper DISARM_REPEAT beeper ARMED beeper SYSTEM_INIT beeper ON_USB beeper LAUNCH_MODE beeper CAM_CONNECTION_OPEN beeper CAM_CONNECTION_CLOSED

map

map TAER

serial

serial 20 1 115200 38400 0 115200 serial 0 64 115200 38400 0 115200 serial 1 2 115200 57600 0 115200 serial 30 2048 115200 38400 0 115200

led

led 0 0,0::C:0 led 1 0,0::C:0 led 2 0,0::C:0 led 3 0,0::C:0 led 4 0,0::C:0 led 5 0,0::C:0 led 6 0,0::C:0 led 7 0,0::C:0 led 8 0,0::C:0 led 9 0,0::C:0 led 10 0,0::C:0 led 11 0,0::C:0 led 12 0,0::C:0 led 13 0,0::C:0 led 14 0,0::C:0 led 15 0,0::C:0 led 16 0,0::C:0 led 17 0,0::C:0 led 18 0,0::C:0 led 19 0,0::C:0 led 20 0,0::C:0 led 21 0,0::C:0 led 22 0,0::C:0 led 23 0,0::C:0 led 24 0,0::C:0 led 25 0,0::C:0 led 26 0,0::C:0 led 27 0,0::C:0 led 28 0,0::C:0 led 29 0,0::C:0 led 30 0,0::C:0 led 31 0,0::C:0

color

color 0 0,0,0 color 1 0,255,255 color 2 0,0,255 color 3 30,0,255 color 4 60,0,255 color 5 90,0,255 color 6 120,0,255 color 7 150,0,255 color 8 180,0,255 color 9 210,0,255 color 10 240,0,255 color 11 270,0,255 color 12 300,0,255 color 13 330,0,255 color 14 0,0,0 color 15 0,0,0

mode_color

mode_color 0 0 1 mode_color 0 1 11 mode_color 0 2 2 mode_color 0 3 13 mode_color 0 4 10 mode_color 0 5 3 mode_color 1 0 5 mode_color 1 1 11 mode_color 1 2 3 mode_color 1 3 13 mode_color 1 4 10 mode_color 1 5 3 mode_color 2 0 10 mode_color 2 1 11 mode_color 2 2 4 mode_color 2 3 13 mode_color 2 4 10 mode_color 2 5 3 mode_color 3 0 8 mode_color 3 1 11 mode_color 3 2 4 mode_color 3 3 13 mode_color 3 4 10 mode_color 3 5 3 mode_color 4 0 7 mode_color 4 1 11 mode_color 4 2 3 mode_color 4 3 13 mode_color 4 4 10 mode_color 4 5 3 mode_color 5 0 9 mode_color 5 1 11 mode_color 5 2 2 mode_color 5 3 13 mode_color 5 4 10 mode_color 5 5 3 mode_color 6 0 6 mode_color 6 1 10 mode_color 6 2 1 mode_color 6 3 0 mode_color 6 4 0 mode_color 6 5 2 mode_color 6 6 3 mode_color 6 7 6 mode_color 6 8 0 mode_color 6 9 0 mode_color 6 10 0

aux

aux 0 0 0 1300 2100 aux 1 2 1 1700 2100 aux 2 3 2 1300 1700 aux 3 9 2 1300 1700 aux 4 8 2 1700 2100 aux 5 10 1 1300 1700 aux 6 14 4 1300 2100 aux 7 27 3 1300 2100 aux 8 18 5 1300 2100 aux 9 0 0 900 900 aux 10 0 0 900 900 aux 11 0 0 900 900 aux 12 0 0 900 900 aux 13 0 0 900 900 aux 14 0 0 900 900 aux 15 0 0 900 900 aux 16 0 0 900 900 aux 17 0 0 900 900 aux 18 0 0 900 900 aux 19 0 0 900 900

adjrange

adjrange 0 0 0 900 900 0 0 adjrange 1 0 0 900 900 0 0 adjrange 2 0 0 900 900 0 0 adjrange 3 0 0 900 900 0 0 adjrange 4 0 0 900 900 0 0 adjrange 5 0 0 900 900 0 0 adjrange 6 0 0 900 900 0 0 adjrange 7 0 0 900 900 0 0 adjrange 8 0 0 900 900 0 0 adjrange 9 0 0 900 900 0 0 adjrange 10 0 0 900 900 0 0 adjrange 11 0 0 900 900 0 0

rxrange

rxrange 0 1000 2000 rxrange 1 1000 2000 rxrange 2 1000 2000 rxrange 3 1000 2000

osd_layout

osd_layout 0 0 3 10 V osd_layout 0 1 1 11 V osd_layout 0 2 0 0 V osd_layout 0 3 8 6 V osd_layout 0 4 8 6 V osd_layout 0 5 23 8 H osd_layout 0 6 23 9 H osd_layout 0 7 2 9 V osd_layout 0 8 20 2 H osd_layout 0 9 23 9 V osd_layout 0 10 8 6 H osd_layout 0 11 9 11 V osd_layout 0 12 16 11 V osd_layout 0 13 2 7 V osd_layout 0 14 2 3 V osd_layout 0 15 23 7 V osd_layout 0 16 2 10 H osd_layout 0 17 2 11 H osd_layout 0 18 2 12 H osd_layout 0 19 15 1 H osd_layout 0 20 15 1 V osd_layout 0 21 3 1 V osd_layout 0 22 25 3 V osd_layout 0 23 23 4 V osd_layout 0 24 12 3 V osd_layout 0 25 23 5 H osd_layout 0 26 24 7 H osd_layout 0 27 3 5 H osd_layout 0 28 23 10 V osd_layout 0 29 23 11 V osd_layout 0 30 0 12 V osd_layout 0 31 2 4 V osd_layout 0 32 12 1 H osd_layout 0 33 6 2 H osd_layout 0 34 10 2 V osd_layout 0 35 1 5 H osd_layout 0 36 1 5 H osd_layout 0 37 1 6 H osd_layout 0 38 1 7 H osd_layout 0 39 1 5 H osd_layout 0 40 1 2 H osd_layout 0 41 1 8 H osd_layout 0 42 1 7 H osd_layout 0 43 0 0 H osd_layout 0 44 0 0 H osd_layout 0 45 0 0 H osd_layout 0 46 3 6 H osd_layout 0 47 3 7 H osd_layout 0 48 23 7 H osd_layout 0 49 23 6 H osd_layout 0 50 0 0 H osd_layout 0 51 12 2 H osd_layout 0 52 12 2 H osd_layout 0 53 12 1 H osd_layout 0 54 12 1 H osd_layout 0 55 1 8 H osd_layout 0 56 2 12 H osd_layout 0 57 2 12 H osd_layout 0 58 2 12 H osd_layout 0 59 2 12 H osd_layout 0 60 2 12 H osd_layout 0 61 2 12 H osd_layout 0 62 2 10 H osd_layout 0 63 2 11 H osd_layout 0 64 2 12 H osd_layout 0 65 2 12 H osd_layout 0 66 2 12 H osd_layout 0 67 2 12 H osd_layout 0 68 2 12 H osd_layout 0 69 2 12 H osd_layout 0 70 2 12 H osd_layout 0 71 2 12 H osd_layout 0 72 2 12 H osd_layout 0 73 2 12 H osd_layout 0 74 2 12 H osd_layout 0 75 2 12 H osd_layout 0 76 2 12 H osd_layout 0 77 2 12 H osd_layout 0 78 0 0 H osd_layout 0 79 2 12 H osd_layout 0 80 2 12 H osd_layout 0 81 2 12 H osd_layout 0 82 2 12 H osd_layout 0 83 2 12 H osd_layout 0 84 2 12 H osd_layout 1 0 23 0 H osd_layout 1 1 12 0 H osd_layout 1 2 0 0 H osd_layout 1 3 8 6 H osd_layout 1 4 8 6 H osd_layout 1 5 23 8 H osd_layout 1 6 23 9 H osd_layout 1 7 12 12 H osd_layout 1 8 20 2 H osd_layout 1 9 1 2 H osd_layout 1 10 8 6 H osd_layout 1 11 1 3 H osd_layout 1 12 1 4 H osd_layout 1 13 23 1 H osd_layout 1 14 0 11 H osd_layout 1 15 1 0 H osd_layout 1 16 2 10 H osd_layout 1 17 2 11 H osd_layout 1 18 2 12 H osd_layout 1 19 15 1 H osd_layout 1 20 18 12 H osd_layout 1 21 0 12 H osd_layout 1 22 14 11 H osd_layout 1 23 1 1 H osd_layout 1 24 12 2 H osd_layout 1 25 23 5 H osd_layout 1 26 24 7 H osd_layout 1 27 3 5 H osd_layout 1 28 23 11 H osd_layout 1 29 23 12 H osd_layout 1 30 1 13 H osd_layout 1 31 0 10 H osd_layout 1 32 12 1 H osd_layout 1 33 6 2 H osd_layout 1 34 18 2 H osd_layout 1 35 1 5 H osd_layout 1 36 1 5 H osd_layout 1 37 1 6 H osd_layout 1 38 1 7 H osd_layout 1 39 1 5 H osd_layout 1 40 1 2 H osd_layout 1 41 1 8 H osd_layout 1 42 1 7 H osd_layout 1 43 0 0 H osd_layout 1 44 0 0 H osd_layout 1 45 0 0 H osd_layout 1 46 3 6 H osd_layout 1 47 3 7 H osd_layout 1 48 23 7 H osd_layout 1 49 23 6 H osd_layout 1 50 0 0 H osd_layout 1 51 12 2 H osd_layout 1 52 12 2 H osd_layout 1 53 12 1 H osd_layout 1 54 12 1 H osd_layout 1 55 1 8 H osd_layout 1 56 2 12 H osd_layout 1 57 2 12 H osd_layout 1 58 2 12 H osd_layout 1 59 2 12 H osd_layout 1 60 2 12 H osd_layout 1 61 2 12 H osd_layout 1 62 2 10 H osd_layout 1 63 2 11 H osd_layout 1 64 2 12 H osd_layout 1 65 2 12 H osd_layout 1 66 2 12 H osd_layout 1 67 2 12 H osd_layout 1 68 2 12 H osd_layout 1 69 2 12 H osd_layout 1 70 2 12 H osd_layout 1 71 2 12 H osd_layout 1 72 2 12 H osd_layout 1 73 2 12 H osd_layout 1 74 2 12 H osd_layout 1 75 2 12 H osd_layout 1 76 2 12 H osd_layout 1 77 2 12 H osd_layout 1 78 0 0 H osd_layout 1 79 2 12 H osd_layout 1 80 2 12 H osd_layout 1 81 2 12 H osd_layout 1 82 2 12 H osd_layout 1 83 2 12 H osd_layout 1 84 2 12 H osd_layout 2 0 23 0 H osd_layout 2 1 12 0 H osd_layout 2 2 0 0 H osd_layout 2 3 8 6 H osd_layout 2 4 8 6 H osd_layout 2 5 23 8 H osd_layout 2 6 23 9 H osd_layout 2 7 12 12 H osd_layout 2 8 20 2 H osd_layout 2 9 1 2 H osd_layout 2 10 8 6 H osd_layout 2 11 1 3 H osd_layout 2 12 1 4 H osd_layout 2 13 23 1 H osd_layout 2 14 0 11 H osd_layout 2 15 1 0 H osd_layout 2 16 2 10 H osd_layout 2 17 2 11 H osd_layout 2 18 2 12 H osd_layout 2 19 15 1 H osd_layout 2 20 18 12 H osd_layout 2 21 0 12 H osd_layout 2 22 14 11 H osd_layout 2 23 1 1 H osd_layout 2 24 12 2 H osd_layout 2 25 23 5 H osd_layout 2 26 24 7 H osd_layout 2 27 3 5 H osd_layout 2 28 23 11 H osd_layout 2 29 23 12 H osd_layout 2 30 1 13 H osd_layout 2 31 0 10 H osd_layout 2 32 12 1 H osd_layout 2 33 6 2 H osd_layout 2 34 18 2 H osd_layout 2 35 1 5 H osd_layout 2 36 1 5 H osd_layout 2 37 1 6 H osd_layout 2 38 1 7 H osd_layout 2 39 1 5 H osd_layout 2 40 1 2 H osd_layout 2 41 1 8 H osd_layout 2 42 1 7 H osd_layout 2 43 0 0 H osd_layout 2 44 0 0 H osd_layout 2 45 0 0 H osd_layout 2 46 3 6 H osd_layout 2 47 3 7 H osd_layout 2 48 23 7 H osd_layout 2 49 23 6 H osd_layout 2 50 0 0 H osd_layout 2 51 12 2 H osd_layout 2 52 12 2 H osd_layout 2 53 12 1 H osd_layout 2 54 12 1 H osd_layout 2 55 1 8 H osd_layout 2 56 2 12 H osd_layout 2 57 2 12 H osd_layout 2 58 2 12 H osd_layout 2 59 2 12 H osd_layout 2 60 2 12 H osd_layout 2 61 2 12 H osd_layout 2 62 2 10 H osd_layout 2 63 2 11 H osd_layout 2 64 2 12 H osd_layout 2 65 2 12 H osd_layout 2 66 2 12 H osd_layout 2 67 2 12 H osd_layout 2 68 2 12 H osd_layout 2 69 2 12 H osd_layout 2 70 2 12 H osd_layout 2 71 2 12 H osd_layout 2 72 2 12 H osd_layout 2 73 2 12 H osd_layout 2 74 2 12 H osd_layout 2 75 2 12 H osd_layout 2 76 2 12 H osd_layout 2 77 2 12 H osd_layout 2 78 0 0 H osd_layout 2 79 2 12 H osd_layout 2 80 2 12 H osd_layout 2 81 2 12 H osd_layout 2 82 2 12 H osd_layout 2 83 2 12 H osd_layout 2 84 2 12 H osd_layout 3 0 23 0 H osd_layout 3 1 12 0 H osd_layout 3 2 0 0 H osd_layout 3 3 8 6 H osd_layout 3 4 8 6 H osd_layout 3 5 23 8 H osd_layout 3 6 23 9 H osd_layout 3 7 12 12 H osd_layout 3 8 20 2 H osd_layout 3 9 1 2 H osd_layout 3 10 8 6 H osd_layout 3 11 1 3 H osd_layout 3 12 1 4 H osd_layout 3 13 23 1 H osd_layout 3 14 0 11 H osd_layout 3 15 1 0 H osd_layout 3 16 2 10 H osd_layout 3 17 2 11 H osd_layout 3 18 2 12 H osd_layout 3 19 15 1 H osd_layout 3 20 18 12 H osd_layout 3 21 0 12 H osd_layout 3 22 14 11 H osd_layout 3 23 1 1 H osd_layout 3 24 12 2 H osd_layout 3 25 23 5 H osd_layout 3 26 24 7 H osd_layout 3 27 3 5 H osd_layout 3 28 23 11 H osd_layout 3 29 23 12 H osd_layout 3 30 1 13 H osd_layout 3 31 0 10 H osd_layout 3 32 12 1 H osd_layout 3 33 6 2 H osd_layout 3 34 18 2 H osd_layout 3 35 1 5 H osd_layout 3 36 1 5 H osd_layout 3 37 1 6 H osd_layout 3 38 1 7 H osd_layout 3 39 1 5 H osd_layout 3 40 1 2 H osd_layout 3 41 1 8 H osd_layout 3 42 1 7 H osd_layout 3 43 0 0 H osd_layout 3 44 0 0 H osd_layout 3 45 0 0 H osd_layout 3 46 3 6 H osd_layout 3 47 3 7 H osd_layout 3 48 23 7 H osd_layout 3 49 23 6 H osd_layout 3 50 0 0 H osd_layout 3 51 12 2 H osd_layout 3 52 12 2 H osd_layout 3 53 12 1 H osd_layout 3 54 12 1 H osd_layout 3 55 1 8 H osd_layout 3 56 2 12 H osd_layout 3 57 2 12 H osd_layout 3 58 2 12 H osd_layout 3 59 2 12 H osd_layout 3 60 2 12 H osd_layout 3 61 2 12 H osd_layout 3 62 2 10 H osd_layout 3 63 2 11 H osd_layout 3 64 2 12 H osd_layout 3 65 2 12 H osd_layout 3 66 2 12 H osd_layout 3 67 2 12 H osd_layout 3 68 2 12 H osd_layout 3 69 2 12 H osd_layout 3 70 2 12 H osd_layout 3 71 2 12 H osd_layout 3 72 2 12 H osd_layout 3 73 2 12 H osd_layout 3 74 2 12 H osd_layout 3 75 2 12 H osd_layout 3 76 2 12 H osd_layout 3 77 2 12 H osd_layout 3 78 0 0 H osd_layout 3 79 2 12 H osd_layout 3 80 2 12 H osd_layout 3 81 2 12 H osd_layout 3 82 2 12 H osd_layout 3 83 2 12 H osd_layout 3 84 2 12 H

master

set looptime = 2000 set gyro_sync = ON set align_gyro = DEFAULT set gyro_hardware_lpf = 20HZ set gyro_lpf_hz = 60 set moron_threshold = 32 set gyro_notch1_hz = 0 set gyro_notch1_cutoff = 1 set gyro_notch2_hz = 0 set gyro_notch2_cutoff = 1 set gyro_stage2_lowpass_hz = 0 set vbat_adc_channel = 1 set rssi_adc_channel = 0 set current_adc_channel = 2 set airspeed_adc_channel = 0 set acc_notch_hz = 0 set acc_notch_cutoff = 1 set align_acc = DEFAULT set acc_hardware = MPU6000 set acc_lpf_hz = 15 set acczero_x = 105 set acczero_y = -38 set acczero_z = -522 set accgain_x = 4095 set accgain_y = 4086 set accgain_z = 4014 set align_mag = DEFAULT set mag_hardware = NONE set mag_declination = 0 set magzero_x = 0 set magzero_y = 0 set magzero_z = 0 set mag_calibration_time = 30 set align_mag_roll = 0 set align_mag_pitch = 0 set align_mag_yaw = 0 set baro_hardware = BMP280 set baro_median_filter = ON set pitot_hardware = NONE set pitot_use_median_filter = ON set pitot_noise_lpf = 0.600 set pitot_scale = 1.000 set receiver_type = SERIAL set min_check = 1100 set max_check = 1900 set rssi_channel = 12 set rssi_min = 0 set rssi_max = 100 set sbus_sync_interval = 3000 set rc_smoothing = ON set serialrx_provider = CRSF set serialrx_inverted = OFF set rx_spi_rf_channel_count = 0 set spektrum_sat_bind = 0 set rx_min_usec = 885 set rx_max_usec = 2115 set serialrx_halfduplex = OFF set blackbox_rate_num = 1 set blackbox_rate_denom = 1 set blackbox_device = SERIAL set min_throttle = 1080 set max_throttle = 2000 set min_command = 1000 set motor_pwm_rate = 2000 set motor_accel_time = 0 set motor_decel_time = 0 set motor_pwm_protocol = MULTISHOT set failsafe_delay = 5 set failsafe_recovery_delay = 5 set failsafe_off_delay = 200 set failsafe_throttle = 1000 set failsafe_throttle_low_delay = 0 set failsafe_procedure = RTH set failsafe_stick_threshold = 50 set failsafe_fw_roll_angle = -200 set failsafe_fw_pitch_angle = 100 set failsafe_fw_yaw_rate = -45 set failsafe_min_distance = 0 set failsafe_min_distance_procedure = DROP set align_board_roll = 0 set align_board_pitch = 0 set align_board_yaw = 0 set vbat_scale = 1100 set current_meter_scale = 423 set current_meter_offset = 0 set current_meter_type = ADC set bat_voltage_src = RAW set cruise_power = 0 set idle_power = 0 set rth_energy_margin = 5 set thr_comp_weight = 1.000 set yaw_motor_direction = 1 set yaw_jump_prevention_limit = 200 set platform_type = AIRPLANE set has_flaps = OFF set model_preview_type = 8 set fw_min_throttle_down_pitch = 0 set 3d_deadband_low = 1406 set 3d_deadband_high = 1514 set 3d_neutral = 1460 set servo_center_pulse = 1500 set servo_pwm_rate = 160 set servo_lpf_hz = 20 set flaperon_throw_offset = 200 set tri_unarmed_servo = ON set reboot_character = 82 set imu_dcm_kp = 2500 set imu_dcm_ki = 50 set imu_dcm_kp_mag = 10000 set imu_dcm_ki_mag = 0 set small_angle = 180 set fixed_wing_auto_arm = OFF set disarm_kill_switch = ON set auto_disarm_delay = 5 set switch_disarm_delay = 250 set gps_provider = UBLOX set gps_sbas_mode = AUTO set gps_dyn_model = AIR_1G set gps_auto_config = ON set gps_auto_baud = ON set gps_ublox_use_galileo = OFF set gps_min_sats = 6 set deadband = 0 set yaw_deadband = 0 set pos_hold_deadband = 20 set alt_hold_deadband = 50 set 3d_deadband_throttle = 50 set fw_autotune_overshoot_time = 100 set fw_autotune_undershoot_time = 200 set fw_autotune_threshold = 50 set fw_autotune_ff_to_p_gain = 10 set fw_autotune_ff_to_i_tc = 600 set inav_auto_mag_decl = ON set inav_gravity_cal_tolerance = 5 set inav_use_gps_velned = ON set inav_allow_dead_reckoning = OFF set inav_reset_altitude = FIRST_ARM set inav_reset_home = EACH_ARM set inav_max_surface_altitude = 200 set inav_w_z_surface_p = 3.500 set inav_w_z_surface_v = 6.100 set inav_w_xy_flow_p = 1.000 set inav_w_xy_flow_v = 2.000 set inav_w_z_baro_p = 0.350 set inav_w_z_gps_p = 0.200 set inav_w_z_gps_v = 0.100 set inav_w_xy_gps_p = 1.000 set inav_w_xy_gps_v = 2.000 set inav_w_z_res_v = 0.500 set inav_w_xy_res_v = 0.500 set inav_w_acc_bias = 0.010 set inav_max_eph_epv = 1000.000 set inav_baro_epv = 100.000 set nav_disarm_on_landing = OFF set nav_use_midthr_for_althold = OFF set nav_extra_arming_safety = ON set nav_user_control_mode = ATTI set nav_position_timeout = 5 set nav_wp_radius = 100 set nav_wp_safe_distance = 10000 set nav_auto_speed = 300 set nav_auto_climb_rate = 500 set nav_manual_speed = 500 set nav_manual_climb_rate = 200 set nav_landing_speed = 200 set nav_land_slowdown_minalt = 500 set nav_land_slowdown_maxalt = 2000 set nav_emerg_landing_speed = 500 set nav_min_rth_distance = 100 set nav_overrides_motor_stop = ON set nav_rth_climb_first = OFF set nav_rth_climb_ignore_emerg = OFF set nav_rth_tail_first = OFF set nav_rth_allow_landing = NEVER set nav_rth_alt_mode = CURRENT set nav_rth_abort_threshold = 50000 set nav_max_terrain_follow_alt = 100 set nav_rth_altitude = 7000 set nav_rth_home_altitude = 0 set nav_mc_bank_angle = 30 set nav_mc_hover_thr = 1500 set nav_mc_auto_disarm_delay = 2000 set nav_fw_cruise_thr = 1750 set nav_fw_min_thr = 1550 set nav_fw_max_thr = 2000 set nav_fw_bank_angle = 30 set nav_fw_climb_angle = 30 set nav_fw_dive_angle = 15 set nav_fw_pitch2thr = 10 set nav_fw_loiter_radius = 4000 set nav_fw_cruise_speed = 0 set nav_fw_land_dive_angle = 2 set nav_fw_launch_velocity = 300 set nav_fw_launch_accel = 1863 set nav_fw_launch_max_angle = 45 set nav_fw_launch_detect_time = 40 set nav_fw_launch_thr = 1700 set nav_fw_launch_idle_thr = 1000 set nav_fw_launch_motor_delay = 500 set nav_fw_launch_spinup_time = 100 set nav_fw_launch_min_time = 0 set nav_fw_launch_timeout = 5000 set nav_fw_launch_max_altitude = 0 set nav_fw_launch_climb_angle = 18 set nav_fw_cruise_yaw_rate = 20 set nav_fw_allow_manual_thr_increase = OFF set telemetry_switch = OFF set telemetry_inverted = OFF set frsky_default_latitude = 0.000 set frsky_default_longitude = 0.000 set frsky_coordinates_format = 0 set frsky_unit = METRIC set frsky_vfas_precision = 0 set frsky_pitch_roll = OFF set report_cell_voltage = OFF set hott_alarm_sound_interval = 5 set smartport_uart_unidir = OFF set smartport_fuel_unit = MAH set ibus_telemetry_type = 0 set ltm_update_rate = NORMAL set ledstrip_visual_beeper = OFF set osd_video_system = PAL set osd_row_shiftdown = 0 set osd_units = IMPERIAL set osd_stats_energy_unit = MAH set osd_rssi_alarm = 70 set osd_time_alarm = 40 set osd_alt_alarm = 122 set osd_dist_alarm = 3219 set osd_neg_alt_alarm = 5 set osd_artificial_horizon_reverse_roll = OFF set osd_crosshairs_style = DEFAULT set osd_left_sidebar_scroll = NONE set osd_right_sidebar_scroll = NONE set osd_sidebar_scroll_arrows = OFF set osd_main_voltage_decimals = 1 set osd_coordinate_digits = 9 set osd_estimations_wind_compensation = ON set i2c_speed = 400KHZ set debug_mode = NONE set acc_task_frequency = 500 set attitude_task_frequency = 250 set async_mode = NONE set throttle_tilt_comp_str = 0 set input_filtering_mode = OFF set name = set mode_range_logic_operator = OR set stats = OFF set stats_total_time = 0 set stats_total_dist = 0 set stats_total_energy = 0 set tz_offset = 0 set tz_automatic_dst = OFF set display_force_sw_blink = OFF set vtx_halfduplex = ON set vtx_band = 4 set vtx_channel = 4 set vtx_power = 3 set vtx_low_power_disarm = ON set vtx_freq = 5800 set vtx_pit_mode_freq = 0

profile

profile 1

set mc_p_pitch = 40 set mc_i_pitch = 30 set mc_d_pitch = 23 set mc_p_roll = 40 set mc_i_roll = 30 set mc_d_roll = 23 set mc_p_yaw = 85 set mc_i_yaw = 45 set mc_d_yaw = 0 set mc_p_level = 20 set mc_i_level = 15 set mc_d_level = 75 set fw_p_pitch = 2 set fw_i_pitch = 15 set fw_ff_pitch = 70 set fw_p_roll = 2 set fw_i_roll = 15 set fw_ff_roll = 30 set fw_p_yaw = 6 set fw_i_yaw = 10 set fw_ff_yaw = 60 set fw_p_level = 10 set fw_i_level = 15 set fw_d_level = 75 set max_angle_inclination_rll = 600 set max_angle_inclination_pit = 600 set dterm_lpf_hz = 40 set yaw_lpf_hz = 30 set dterm_setpoint_weight = 1.000 set fw_iterm_throw_limit = 165 set fw_reference_airspeed = 1000.000 set fw_turn_assist_yaw_gain = 1.000 set dterm_notch_hz = 0 set dterm_notch_cutoff = 1 set pidsum_limit = 500 set yaw_p_limit = 300 set iterm_windup = 50 set rate_accel_limit_roll_pitch = 0 set rate_accel_limit_yaw = 10000 set heading_hold_rate_limit = 90 set nav_mc_pos_z_p = 50 set nav_mc_pos_z_i = 0 set nav_mc_pos_z_d = 0 set nav_mc_vel_z_p = 100 set nav_mc_vel_z_i = 50 set nav_mc_vel_z_d = 10 set nav_mc_pos_xy_p = 65 set nav_mc_pos_xy_i = 120 set nav_mc_pos_xy_d = 10 set nav_mc_vel_xy_p = 40 set nav_mc_vel_xy_i = 15 set nav_mc_vel_xy_d = 100 set nav_mc_heading_p = 60 set nav_fw_pos_z_p = 40 set nav_fw_pos_z_i = 5 set nav_fw_pos_z_d = 10 set nav_fw_pos_xy_p = 75 set nav_fw_pos_xy_i = 5 set nav_fw_pos_xy_d = 8 set nav_fw_heading_p = 60 set thr_mid = 50 set thr_expo = 0 set tpa_rate = 33 set tpa_breakpoint = 1300 set fw_tpa_time_constant = 0 set rc_expo = 70 set rc_yaw_expo = 20 set roll_rate = 35 set pitch_rate = 9 set yaw_rate = 20 set manual_rc_expo = 70 set manual_rc_yaw_expo = 20 set manual_roll_rate = 100 set manual_pitch_rate = 100 set manual_yaw_rate = 100

battery_profile

battery_profile 1

set bat_cells = 0 set vbat_cell_detect_voltage = 430 set vbat_max_cell_voltage = 420 set vbat_min_cell_voltage = 275 set vbat_warning_cell_voltage = 330 set battery_capacity = 3200 set battery_capacity_warning = 0 set battery_capacity_critical = 0 set battery_capacity_unit = MAH

Rclay11541 commented 5 years ago

I have an Omnibus NXT F7 and had similar issues....

I got Smart Audio working by: 1) Resolder from the dedicated SA Pad to UART 3. 2) Set VTX Half Duplex to ON

Your seeing dashes likely because of a ground issue. Try soldering your Camera, VTX, and FC all to the same ground. You can also try setting to a different OSD Font.

Good Luck!

shellixyz commented 5 years ago

all I see are dashes where there should be channel and power information.

You probably need to update the OSD font

Nihilistic commented 5 years ago

@Rclay11541 The F411 Wing only has two UARTs. My Crossfire NanoRx is on UART1, and GPS is on UART2. Which is why I want to use Soft Serial for SA.

There might possibly be some ground issue, as you suggested, because I'm using a 12V step up to power the VTX off of the 2S 18650 lithium ion pack. Powering the camera from the 5V and ground pads on the FC.

@shellixyz and @Rclay11541 Everything else on my OSD works and looks normal on my OSD, so I don't think it has anything to do with the font. I loaded the default font the very first step when setting up OSD.

Nihilistic commented 5 years ago

Moved the camera power and ground leads straight to the battery, and the Vtx ground to the battery, and the 12V polulu step up to the battery, and the output from the Polulu to Vtx. Didn't help.

And I updated to iNAV 2.0.1 to avoid the potential GPS lag issue.

stale[bot] commented 5 years ago

This issue / pull request has been automatically marked as stale because it has not had any activity in 60 days. The resources of the INAV team are limited, and so we are asking for your help. This issue / pull request will be closed if no further activity occurs within two weeks.

stale[bot] commented 5 years ago

Automatically closing as inactive.

Ozydego commented 5 years ago

Has anyone had success with this? I can enable soft serial in Betaflight and use the F411-Wing without issue, as well as use a normal UART for smart audio in inav 2.1.0. It won't work with the ST1 pin though.

Nihilistic commented 5 years ago

@Ozydego I moved the SA wire from the ST1 pin on the F411-Wing to the TX pad on my Crossfire Nano RX, and can now access all the SA features via the luascript on my Taranis. The only thing missing is the auto power switching feature available through the FC. This would be nice, because you could set the VTX to minimum power while on the ground waiting for a GPS lock, or while tinkering on the bench, to avoid overheating. Then upon arming, the FC would kick the VTX up to your preferred max power setting. As it is now, I just have to remember to bump the VTX power up manually before launching. Smart Audio is essential to my build, because the VTX is embedded in the wing of my Nano Goblin, button side down, to maximize air flow over the heat sink side.

It doesn't look like this issue is going to get any attention unless more people chime in. I'm surprised there haven't been more complaints, because I followed a build video posted by RMRC on the Nano Goblin using the F411-Wing, and he set up SA on the ST1 pin using Soft Serial, but never actually verified that it worked.

jkflying commented 5 years ago

I'm using the latest development branch and I have SmartAudio 2.1 working on ST1 pin. It didn't work at first, but I then realised that the support for SmartAudio 2.1 was only merged a few weeks ago, ported across from Betaflight, and my VTX runs SmartAudio 2.1.

(Also on a Nano Goblin, fantastic plane!)

Ozydego commented 5 years ago

@jkflying can you point me to the development branch?

jkflying commented 5 years ago

https://github.com/iNavFlight/inav/tree/development

Otherwise if you used git clone to get the source, you just need to do git fetch && git checkout origin/development to get the latest development branch.

I've attached the hexs from the version I built (16faa4399f2d28699f1be9791494c40c1f2c12f6)

MATEKF411_16faa4399f2d28699f1be9791494c40c1f2c12f6.zip

jasonsmit4 commented 5 years ago

I can confirm this issue still exists on iNav 2.2 RC2.

RCManiac98 commented 5 years ago

I'm using the latest development branch and I have SmartAudio 2.1 working on ST1 pin. It didn't work at first, but I then realised that the support for SmartAudio 2.1 was only merged a few weeks ago, ported across from Betaflight, and my VTX runs SmartAudio 2.1.

(Also on a Nano Goblin, fantastic plane!)

Could you please clarify exactly what steps you took to get SmartAudio working on the ST1 pin?

JohnHennesey commented 4 years ago

Oh no! closed? I too am a proud nano goblin owner... while I am able to access the buttons, I want to get into SA to disable a message generated in the VTX on the OSD display.

Anybody ever have any luck with this? F411 WSE + RMRC Cricket Pro V2.

knutigro commented 3 years ago

I have same issue on 2.6.0 / Knut

fpvMarkS commented 1 month ago

INAV 6.1.1 and still can't get smartaudio working over softserial using st1 pad TBS Unify Pro32 HV