CRSF/ELRS telemetry issue on Matek F405-wing V2

[krugs44364]

Current Behavior

I recently purchased a Matek F405-wing V2 and I am unable to get CRSF/ELRS telemetry working. The RX channels works. The only telemetry back to the radio (TS16S) if the receiver telemetry. Nothing from the FC.

Steps to Reproduce

1. Flashed Inav 7.0
2. Connect Radiomaster Rp# ELRS receiver on UART2
3. set parameters as per Matek's recommendations product data sheet for the CRSF protocol

Expected behavior

Full FC telemetry back to TX16S radio

Suggested solution(s)

I suspect the firmware has a bug that is not sending Telemetry data to the TX2 pin for the CRSF protocol.

Additional context

I have connected the same Rp3 rx to 2 other Matek FCs I have on hand, an F405-WMN and an F465-wing, both flashed with version 7 and the telemetry works. Used the same model on the TX16s as well, which proves that the ELRS setup is correct. I have also tried another F405-wing V2 and it has the same behaviour. So that rules out a faulty FC. To further prove that the FC hardware is ok, I also set up a Radiomast R161 receiver using SBUS and Smartport telemetry on UART2, and the telemetry works. As a final test and out of desperation, I then flashed Arduplane firmware on one of the F405-wing V2s and got working telemetry with the ELRS receiver. I also tried version 6.0 and the issue was the same.

Some background: I initially purchased one Matek F405-wing V2 from AliExpres in December 2023. When I couldn't get that to work I purchased a 2nd one from PhaserFPV in Sydney to rule out a faulty FC.

INAV_7.0.0_cli_20240202_063952.txt

---

version

INAV/MATEKF405SE 7.0.0 Dec 5 2023 / 10:29:45 (895a4f31)

GCC-10.3.1 20210824 (release)

• FC Board name and vendor: Matek F405-wing V2
• INAV version string: Version 7

[sensei-hacker]

From the Matek product page:

Softserial_tx1 is enabled on Tx2 pad by default for Frsky SmartPort telemetry. If using CRSF protocol receiver(TBS, ELRS etc), CPU based serial port(softserial) should be disable in INAV configurator.

Did you turn off soft serial?

If so, lack of telemetry from the FC to the reciever with ELRS generally indicates a fault in the connection between FC tx pad and the receiver rx pad. Often, this is caused by a wire being broken within the insulation. This can be caused when the wire was previously caught under a screw / standoff, or if it gets kinked.

It can also be a soldering issue, but in your case I suspect a bad wire is more likely, if you turned off SoftSerial.

[krugs44364]

Hi Sensei. Yes, I have. Last night I also succesfully tested the board with a Radiomaster R161 receiver which uses SBUS in the board's SBUS pin and Smartport for telemetry which uses the TX2 pin albeit with softserial. However, it proves the board's hardware works. To prove the ELRS receiver, I connected the same receiver to another FC (Matek F405-WMN) I have and the telemetry works. That leaves only firmware in my opinion. I have tried to flash Inav 6 but the problem was the same. Lastly I flashed Arduplane to the F405-wing V2 board and the telemetry via the ELRS receiver worked. This again proves to me it is the INAV firmware that is the issue.

On Fri, Feb 2, 2024 at 1:46 PM Sensei @.***> wrote:

From the Matek product page:

Softserial_tx1 is enabled on Tx2 pad by default for Frsky SmartPort telemetry. If using CRSF protocol receiver(TBS, ELRS etc), CPU based serial port(softserial) should be disable in INAV configurator.

Did you turn off soft serial?

If so, lack of telemetry from the FC to the reciever with ELRS generally indicates a fault in the connection between FC tx pad and the receiver rx pad. Often, this is caused by a wire being broken within the insulation. This can be caused when the wire was previously caught under a screw / standoff, or if it gets kinked.

It can also be a soldering issue, but in your case I suspect a bad wire is more likely, if you turned off SoftSerial.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1922693504, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC5YZW2OZ4NZWV76AQYTYRRHSFAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRSGY4TGNJQGQ . You are receiving this because you authored the thread.Message ID: @.***>

-- Kind regards, Carel Kruger

[sensei-hacker]

I would triple check with SoftSerial definitely turned off.

The firmware doesn't have specific code for "CRSF on uart2". Uart2 could be broken in the firmware, or CRSF could be broken, but "CRSF on uart2" doesn't exist in the firmware, and therefore could not be broken.

In your shoes, after triple checking that soft serial really is off, I would test it on uart 5 or uart 6 with a new piece of wire. A wire broken inside the insulation (or plug) is the most common cause of this issue, on all boards. Obviously on that particular board, not realizing you need to actively turn off SoftSerial is a bigger issue.

[krugs44364]

Hi Sensei, Thank you for your response.

Yes, I have also been talking to support from my local supplier, and from that, I have checked that soft serial is off multiple times. I have also tried UARTS 5 and 6.

If you read my previous response again you will see that I have managed to establish telemetry with the same rX and "wire" when I flashed Ardupilot firmware on the FC. I think that rules out any possible "wire" issues.

You are saying CRSF on UART2 doesn't exist but I'm sure you can understand that what I mean is I have the receiver connected to UART 2 and have selected CRSF protocol.

The other point I mentioned that you may have missed is that I used the same receiver and hence the same "wire" on another FC that I have (a Matek F405-WMN) and the telemetry works. So definitely not a wire issue. Furthermore, I also tried with another receiver (betafpv nano 900Mhz) but was unable to get telemetry going on the Matek F405-wing V2 while it works on the F405-WMN.

So the point is I have proven beyond any doubt that is it not hardware, not a wire issue, and not a receiver issue. The F405-Wing V2 and the F405-WMN use different firmware loads. So you are correct it is most likely that CRSF tlemetry is broken in the firmware. Since it gives the same issue on UART 5 and 6 is is unlikely that it is a problem with UART2.

As another, point., I also tried the same wire and receiver on an old Matek F465-wing I have and again the telemetry works!

NB. I have got a lot of experience with setting up ELRS on Matek FC's and have never run into a problem that didn't have a simple solution except now.

I appreciate your assistance and I understand you want to make sure it is not something silly that I have missed but I have provided enough info here that should make it clear that I haven't missed anything.

I've attached some screen shots:

[image: Receiver.JPG] [image: ports.JPG] [image: Config.JPG] Thanks for your help so far.

On Fri, Feb 2, 2024 at 2:26 PM Sensei @.***> wrote:

I would triple check with SoftSerial definitely turned off.

The firmware doesn't have specific code for "CRSF on uart2". Uart2 could be broken in the firmware, or CRSF could be broken, but "CRSF on uart2" doesn't exist in the firmware, and therefore could not be broken.

In your shoes, after triple checking that soft serial really is off, I would test it on uart 5 or uart 6 with a new piece of wire. A wire broken inside the insulation (or plug is the most common cause of this issue, on all boards. Obviously on that particular board, not realizing you need to actively turn off SoftSerial is a bigger issue.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1922739332, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC53IF6DGDUP5GSRVQPLYRRMFLAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRSG4ZTSMZTGI . You are receiving this because you authored the thread.Message ID: @.***>

-- Kind regards, Carel Kruger

[sensei-hacker]

Email replies to Github issues don't carry the screenshots. Can you please attach those via the Github web site. Particularly your ports tab, because the attached diff indicates there may be something interesting there, but I would like to confirm visually. Also a dump could be handy.

If you read my previous response again you will see that I have managed to establish telemetry with the same rX and "wire"

Previously, you didn't mention which side you desoldered the wire from - the FC or the receiver. Moving a receiver from one FC to another, one could leave the old wire on the FC, or on the receiver.

So the point is I have proven beyond any doubt that is it not hardware, not a wire issue, and not a receiver issue. The F405-Wing V2 and the F405-WMN use different firmware loads. So you are correct it is most likely that CRSF tlemetry is broken in the firmware. Since it gives the same issue on UART 5 and 6 is is unlikely that it is a problem with UART2.

Assuming all of your tests are correct, it would mean that: It's not a problem with that UART. It's not a problem with the hardware It's not a problem with the receiver It's not a problem with the wiring

Therefore, either: A. It's just that crsf doesn't work in INAV. Meaning ELRS doesn't work with INAV.
B. You've "proven" something that isn't true. (testing error) C. Configuration problem

A is obviously not the case. Thousands of people use it every day. "it is most likely that CRSF tlemetry is broken in the firmware" - telemetry has been broken for most INAV users for over a year and nobody noticed? Seems unlikely. :)

However, your diff indicates C is worth looking at a bit closer. In particular the ports config.

[sensei-hacker]

Here's something you can try, BTW:

Turn SoftSerial back on. Save and reboot. I think you will see smartport telemetry will be enabled on Softserial by default. Remove smartport from softserial. Save and reboot. Disable softserial. Save and reboot.

Discover new telemetry sensors.

It's possible that the default config (smartport on softserial) is trying to send telemetry to a port that does not exist. This could cause telemetry problems.

[krugs44364]

Hi Sensei, I don’t de-solder and re-solder when I move the receiver from one FC to another. I is on a DuPont 4 pin connector.

I will send a dump. Should I also send a dump of the F405-WMN where the telemetry works for comparison?

Kind regards, Carel Kruger

On Fri, 2 Feb 2024 at 3:41 pm, Sensei @.***> wrote:

Email replies to Github issues don't carry the screenshots. Can you please attach those via the Github web site. Particularly your ports tab, because the attached diff indicates there may be something interesting there, but I would like to confirm visually. Also a dump could be handy.

If you read my previous response again you will see that I have managed to establish telemetry with the same rX and "wire"

Previously, you didn't mention which side you desoldered the wire from - the FC or the receiver. Moving a receiver from one FC to another, one could leave the old wire on the FC, or on the receiver.

So the point is I have proven beyond any doubt that is it not hardware, not a wire issue, and not a receiver issue. The F405-Wing V2 and the F405-WMN use different firmware loads. So you are correct it is most likely that CRSF tlemetry is broken in the firmware. Since it gives the same issue on UART 5 and 6 is is unlikely that it is a problem with UART2.

Assuming all of your tests are correct, it would mean that: It's not a problem with that UART. It's not a problem with the hardware It's not a problem with the receiver It's not a problem with the wiring

Therefore, either: A. It's just that crsf doesn't work in INAV. Meaning ELRS doesn't work with INAV. B. You've "proven" something that isn't true. (testing error) C. Configuration problem

A is obviously not the case. Thousands of people use it every day.

However, your diff indicates C is worth looking at a bit closer. In particular the ports config.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1922807510, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC5YGFKDIKKLUVBVZES3YRRU7FAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRSHAYDONJRGA . You are receiving this because you authored the thread.Message ID: @.***>

[sensei-hacker]

Ah that makes sense, Carel. I fly mostly fixed wing, but don't use Dupont because they are so darn big. It didn't occur to me you were likely using Dupont.

A dump of the WMN for comparison sounds good too.

[krugs44364]

Thanks, I will give it a go.

Kind regards, Carel Kruger

On Fri, 2 Feb 2024 at 4:05 pm, Sensei @.***> wrote:

Here's something you can try, BTW:

Turn SoftSerial back on. Save and reboot. I think you will see smartport telemetry will be enabled on Softserial by default. Remove smartport from softserial. Save and reboot. Disable softserial.

Discover new telemetry sensors.

It's possible that the default config is trying to send telemetry to a port that does not exist.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1922832405, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC55G35BQVCXDU5WDMNDYRRXZ5AVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRSHAZTENBQGU . You are receiving this because you authored the thread.Message ID: @.***>

[krugs44364]

Dump files:

On Fri, Feb 2, 2024 at 4:08 PM Sensei @.***> wrote:

Ah that makes sense, Carel. I fly mostly fixed wing, but don't use Dupont because they are so darn big. It didn't occur to me you were likely using Dupont.

A dump of the WMN for comparison sounds good too.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1922836808, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC56JWTXCR4CRV55RENDYRRYF3AVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRSHAZTMOBQHA . You are receiving this because you authored the thread.Message ID: @.***>

-- Kind regards, Carel Kruger

dump

version

INAV/MATEKF405SE 7.0.0 Dec 5 2023 / 10:29:45 (895a4f31)

GCC-10.3.1 20210824 (release)

start the command batch

batch start

resources

Timer overrides

timer_output_mode 0 AUTO timer_output_mode 1 AUTO timer_output_mode 2 AUTO timer_output_mode 3 AUTO timer_output_mode 4 AUTO timer_output_mode 5 AUTO timer_output_mode 6 AUTO timer_output_mode 7 AUTO timer_output_mode 8 AUTO timer_output_mode 9 AUTO timer_output_mode 10 AUTO timer_output_mode 11 AUTO timer_output_mode 12 AUTO timer_output_mode 13 AUTO

Outputs [servo]

servo 0 1000 2000 1500 100 servo 1 1000 2000 1500 100 servo 2 1000 2000 1500 100 servo 3 1000 2000 1500 100 servo 4 1000 2000 1500 100 servo 5 1000 2000 1500 100 servo 6 1000 2000 1500 100 servo 7 1000 2000 1500 100 servo 8 1000 2000 1500 100 servo 9 1000 2000 1500 100 servo 10 1000 2000 1500 100 servo 11 1000 2000 1500 100 servo 12 1000 2000 1500 100 servo 13 1000 2000 1500 100 servo 14 1000 2000 1500 100 servo 15 1000 2000 1500 100

safehome

safehome 0 0 0 0 safehome 1 0 0 0 safehome 2 0 0 0 safehome 3 0 0 0 safehome 4 0 0 0 safehome 5 0 0 0 safehome 6 0 0 0 safehome 7 0 0 0

features

feature -THR_VBAT_COMP feature -VBAT feature -TX_PROF_SEL feature -BAT_PROF_AUTOSWITCH feature -MOTOR_STOP feature -SOFTSERIAL feature -GPS feature -RPM_FILTERS feature -TELEMETRY feature -CURRENT_METER feature -REVERSIBLE_MOTORS feature -RSSI_ADC feature -LED_STRIP feature -DASHBOARD feature -BLACKBOX feature -TRANSPONDER feature -AIRMODE feature -SUPEREXPO feature -VTX feature -PWM_OUTPUT_ENABLE feature -OSD feature -FW_LAUNCH feature -FW_AUTOTRIM feature VBAT feature TX_PROF_SEL feature TELEMETRY feature CURRENT_METER feature AIRMODE feature PWM_OUTPUT_ENABLE feature OSD

beeper

beeper RUNTIME_CALIBRATION beeper HW_FAILURE beeper RX_LOST beeper RX_LOST_LANDING beeper DISARMING beeper ARMING beeper ARMING_GPS_FIX beeper BAT_CRIT_LOW beeper BAT_LOW beeper GPS_STATUS beeper RX_SET beeper ACTION_SUCCESS beeper ACTION_FAIL beeper READY_BEEP beeper MULTI_BEEPS beeper DISARM_REPEAT beeper ARMED beeper SYSTEM_INIT beeper ON_USB beeper LAUNCH_MODE beeper LAUNCH_MODE_LOW_THROTTLE beeper LAUNCH_MODE_IDLE_START beeper CAM_CONNECTION_OPEN beeper CAM_CONNECTION_CLOSED

blackbox

blackbox -NAV_ACC blackbox NAV_POS blackbox NAV_PID blackbox MAG blackbox ACC blackbox ATTI blackbox RC_DATA blackbox RC_COMMAND blackbox MOTORS blackbox -GYRO_RAW blackbox -PEAKS_R blackbox -PEAKS_P blackbox -PEAKS_Y

Receiver: Channel map

map AETR

Ports

serial 20 1 115200 115200 0 115200 serial 0 1 115200 115200 0 115200 serial 1 64 115200 115200 0 115200 serial 2 0 115200 115200 0 115200 serial 3 0 115200 115200 0 115200 serial 4 0 115200 115200 0 115200 serial 5 0 115200 115200 0 115200

LEDs

led 0 0,0::C:0 led 1 0,0::C:0 led 2 0,0::C:0 led 3 0,0::C:0 led 4 0,0::C:0 led 5 0,0::C:0 led 6 0,0::C:0 led 7 0,0::C:0 led 8 0,0::C:0 led 9 0,0::C:0 led 10 0,0::C:0 led 11 0,0::C:0 led 12 0,0::C:0 led 13 0,0::C:0 led 14 0,0::C:0 led 15 0,0::C:0 led 16 0,0::C:0 led 17 0,0::C:0 led 18 0,0::C:0 led 19 0,0::C:0 led 20 0,0::C:0 led 21 0,0::C:0 led 22 0,0::C:0 led 23 0,0::C:0 led 24 0,0::C:0 led 25 0,0::C:0 led 26 0,0::C:0 led 27 0,0::C:0 led 28 0,0::C:0 led 29 0,0::C:0 led 30 0,0::C:0 led 31 0,0::C:0

LED color

color 0 0,0,0 color 1 0,255,255 color 2 0,0,255 color 3 30,0,255 color 4 60,0,255 color 5 90,0,255 color 6 120,0,255 color 7 150,0,255 color 8 180,0,255 color 9 210,0,255 color 10 240,0,255 color 11 270,0,255 color 12 300,0,255 color 13 330,0,255 color 14 0,0,0 color 15 0,0,0

LED mode_color

mode_color 0 0 1 mode_color 0 1 11 mode_color 0 2 2 mode_color 0 3 13 mode_color 0 4 10 mode_color 0 5 3 mode_color 1 0 5 mode_color 1 1 11 mode_color 1 2 3 mode_color 1 3 13 mode_color 1 4 10 mode_color 1 5 3 mode_color 2 0 10 mode_color 2 1 11 mode_color 2 2 4 mode_color 2 3 13 mode_color 2 4 10 mode_color 2 5 3 mode_color 3 0 8 mode_color 3 1 11 mode_color 3 2 4 mode_color 3 3 13 mode_color 3 4 10 mode_color 3 5 3 mode_color 4 0 7 mode_color 4 1 11 mode_color 4 2 3 mode_color 4 3 13 mode_color 4 4 10 mode_color 4 5 3 mode_color 5 0 9 mode_color 5 1 11 mode_color 5 2 2 mode_color 5 3 13 mode_color 5 4 10 mode_color 5 5 3 mode_color 6 0 6 mode_color 6 1 10 mode_color 6 2 1 mode_color 6 3 0 mode_color 6 4 0 mode_color 6 5 2 mode_color 6 6 3 mode_color 6 7 6 mode_color 6 8 1

Modes [aux]

aux 0 0 0 1700 2100 aux 1 1 6 900 1300 aux 2 2 6 1300 1700 aux 3 12 2 1300 2100 aux 4 3 1 1300 2100 aux 5 35 6 900 1300 aux 6 34 4 1300 2100 aux 7 20 5 1300 2100 aux 8 0 0 900 900 aux 9 0 0 900 900 aux 10 0 0 900 900 aux 11 0 0 900 900 aux 12 0 0 900 900 aux 13 0 0 900 900 aux 14 0 0 900 900 aux 15 0 0 900 900 aux 16 0 0 900 900 aux 17 0 0 900 900 aux 18 0 0 900 900 aux 19 0 0 900 900 aux 20 0 0 900 900 aux 21 0 0 900 900 aux 22 0 0 900 900 aux 23 0 0 900 900 aux 24 0 0 900 900 aux 25 0 0 900 900 aux 26 0 0 900 900 aux 27 0 0 900 900 aux 28 0 0 900 900 aux 29 0 0 900 900 aux 30 0 0 900 900 aux 31 0 0 900 900 aux 32 0 0 900 900 aux 33 0 0 900 900 aux 34 0 0 900 900 aux 35 0 0 900 900 aux 36 0 0 900 900 aux 37 0 0 900 900 aux 38 0 0 900 900 aux 39 0 0 900 900

Adjustments [adjrange]

adjrange 0 0 0 900 900 0 0 adjrange 1 0 0 900 900 0 0 adjrange 2 0 0 900 900 0 0 adjrange 3 0 0 900 900 0 0 adjrange 4 0 0 900 900 0 0 adjrange 5 0 0 900 900 0 0 adjrange 6 0 0 900 900 0 0 adjrange 7 0 0 900 900 0 0 adjrange 8 0 0 900 900 0 0 adjrange 9 0 0 900 900 0 0 adjrange 10 0 0 900 900 0 0 adjrange 11 0 0 900 900 0 0 adjrange 12 0 0 900 900 0 0 adjrange 13 0 0 900 900 0 0 adjrange 14 0 0 900 900 0 0 adjrange 15 0 0 900 900 0 0 adjrange 16 0 0 900 900 0 0 adjrange 17 0 0 900 900 0 0 adjrange 18 0 0 900 900 0 0 adjrange 19 0 0 900 900 0 0

Receiver rxrange

rxrange 0 1000 2000 rxrange 1 1000 2000 rxrange 2 1000 2000 rxrange 3 1000 2000

temp_sensor

temp_sensor 0 0 0 0 0 0 temp_sensor 1 0 0 0 0 0 temp_sensor 2 0 0 0 0 0 temp_sensor 3 0 0 0 0 0 temp_sensor 4 0 0 0 0 0 temp_sensor 5 0 0 0 0 0 temp_sensor 6 0 0 0 0 0 temp_sensor 7 0 0 0 0 0

Mission Control Waypoints [wp]

wp 0 invalid

wp 0 0 0 0 0 0 0 0 0 wp 1 0 0 0 0 0 0 0 0 wp 2 0 0 0 0 0 0 0 0 wp 3 0 0 0 0 0 0 0 0 wp 4 0 0 0 0 0 0 0 0 wp 5 0 0 0 0 0 0 0 0 wp 6 0 0 0 0 0 0 0 0 wp 7 0 0 0 0 0 0 0 0 wp 8 0 0 0 0 0 0 0 0 wp 9 0 0 0 0 0 0 0 0 wp 10 0 0 0 0 0 0 0 0 wp 11 0 0 0 0 0 0 0 0 wp 12 0 0 0 0 0 0 0 0 wp 13 0 0 0 0 0 0 0 0 wp 14 0 0 0 0 0 0 0 0 wp 15 0 0 0 0 0 0 0 0 wp 16 0 0 0 0 0 0 0 0 wp 17 0 0 0 0 0 0 0 0 wp 18 0 0 0 0 0 0 0 0 wp 19 0 0 0 0 0 0 0 0 wp 20 0 0 0 0 0 0 0 0 wp 21 0 0 0 0 0 0 0 0 wp 22 0 0 0 0 0 0 0 0 wp 23 0 0 0 0 0 0 0 0 wp 24 0 0 0 0 0 0 0 0 wp 25 0 0 0 0 0 0 0 0 wp 26 0 0 0 0 0 0 0 0 wp 27 0 0 0 0 0 0 0 0 wp 28 0 0 0 0 0 0 0 0 wp 29 0 0 0 0 0 0 0 0 wp 30 0 0 0 0 0 0 0 0 wp 31 0 0 0 0 0 0 0 0 wp 32 0 0 0 0 0 0 0 0 wp 33 0 0 0 0 0 0 0 0 wp 34 0 0 0 0 0 0 0 0 wp 35 0 0 0 0 0 0 0 0 wp 36 0 0 0 0 0 0 0 0 wp 37 0 0 0 0 0 0 0 0 wp 38 0 0 0 0 0 0 0 0 wp 39 0 0 0 0 0 0 0 0 wp 40 0 0 0 0 0 0 0 0 wp 41 0 0 0 0 0 0 0 0 wp 42 0 0 0 0 0 0 0 0 wp 43 0 0 0 0 0 0 0 0 wp 44 0 0 0 0 0 0 0 0 wp 45 0 0 0 0 0 0 0 0 wp 46 0 0 0 0 0 0 0 0 wp 47 0 0 0 0 0 0 0 0 wp 48 0 0 0 0 0 0 0 0 wp 49 0 0 0 0 0 0 0 0 wp 50 0 0 0 0 0 0 0 0 wp 51 0 0 0 0 0 0 0 0 wp 52 0 0 0 0 0 0 0 0 wp 53 0 0 0 0 0 0 0 0 wp 54 0 0 0 0 0 0 0 0 wp 55 0 0 0 0 0 0 0 0 wp 56 0 0 0 0 0 0 0 0 wp 57 0 0 0 0 0 0 0 0 wp 58 0 0 0 0 0 0 0 0 wp 59 0 0 0 0 0 0 0 0 wp 60 0 0 0 0 0 0 0 0 wp 61 0 0 0 0 0 0 0 0 wp 62 0 0 0 0 0 0 0 0 wp 63 0 0 0 0 0 0 0 0 wp 64 0 0 0 0 0 0 0 0 wp 65 0 0 0 0 0 0 0 0 wp 66 0 0 0 0 0 0 0 0 wp 67 0 0 0 0 0 0 0 0 wp 68 0 0 0 0 0 0 0 0 wp 69 0 0 0 0 0 0 0 0 wp 70 0 0 0 0 0 0 0 0 wp 71 0 0 0 0 0 0 0 0 wp 72 0 0 0 0 0 0 0 0 wp 73 0 0 0 0 0 0 0 0 wp 74 0 0 0 0 0 0 0 0 wp 75 0 0 0 0 0 0 0 0 wp 76 0 0 0 0 0 0 0 0 wp 77 0 0 0 0 0 0 0 0 wp 78 0 0 0 0 0 0 0 0 wp 79 0 0 0 0 0 0 0 0 wp 80 0 0 0 0 0 0 0 0 wp 81 0 0 0 0 0 0 0 0 wp 82 0 0 0 0 0 0 0 0 wp 83 0 0 0 0 0 0 0 0 wp 84 0 0 0 0 0 0 0 0 wp 85 0 0 0 0 0 0 0 0 wp 86 0 0 0 0 0 0 0 0 wp 87 0 0 0 0 0 0 0 0 wp 88 0 0 0 0 0 0 0 0 wp 89 0 0 0 0 0 0 0 0 wp 90 0 0 0 0 0 0 0 0 wp 91 0 0 0 0 0 0 0 0 wp 92 0 0 0 0 0 0 0 0 wp 93 0 0 0 0 0 0 0 0 wp 94 0 0 0 0 0 0 0 0 wp 95 0 0 0 0 0 0 0 0 wp 96 0 0 0 0 0 0 0 0 wp 97 0 0 0 0 0 0 0 0 wp 98 0 0 0 0 0 0 0 0 wp 99 0 0 0 0 0 0 0 0 wp 100 0 0 0 0 0 0 0 0 wp 101 0 0 0 0 0 0 0 0 wp 102 0 0 0 0 0 0 0 0 wp 103 0 0 0 0 0 0 0 0 wp 104 0 0 0 0 0 0 0 0 wp 105 0 0 0 0 0 0 0 0 wp 106 0 0 0 0 0 0 0 0 wp 107 0 0 0 0 0 0 0 0 wp 108 0 0 0 0 0 0 0 0 wp 109 0 0 0 0 0 0 0 0 wp 110 0 0 0 0 0 0 0 0 wp 111 0 0 0 0 0 0 0 0 wp 112 0 0 0 0 0 0 0 0 wp 113 0 0 0 0 0 0 0 0 wp 114 0 0 0 0 0 0 0 0 wp 115 0 0 0 0 0 0 0 0 wp 116 0 0 0 0 0 0 0 0 wp 117 0 0 0 0 0 0 0 0 wp 118 0 0 0 0 0 0 0 0 wp 119 0 0 0 0 0 0 0 0

OSD [osd_layout]

osd_layout 0 0 23 0 V osd_layout 0 1 12 0 V osd_layout 0 2 0 0 H osd_layout 0 3 8 6 H osd_layout 0 4 8 6 H osd_layout 0 5 23 8 H osd_layout 0 6 23 9 H osd_layout 0 7 13 12 V osd_layout 0 8 20 2 H osd_layout 0 9 1 2 V osd_layout 0 10 8 6 H osd_layout 0 11 2 3 V osd_layout 0 12 1 4 V osd_layout 0 13 23 1 H osd_layout 0 14 0 11 V osd_layout 0 15 1 0 V osd_layout 0 16 2 10 H osd_layout 0 17 2 11 H osd_layout 0 18 2 12 H osd_layout 0 19 15 1 H osd_layout 0 20 18 12 H osd_layout 0 21 0 12 H osd_layout 0 22 14 11 H osd_layout 0 23 1 1 H osd_layout 0 24 12 2 H osd_layout 0 25 23 5 H osd_layout 0 26 24 7 H osd_layout 0 27 3 5 H osd_layout 0 28 23 11 V osd_layout 0 29 23 12 H osd_layout 0 30 1 13 V osd_layout 0 31 0 10 H osd_layout 0 32 12 1 H osd_layout 0 33 6 2 H osd_layout 0 34 18 2 H osd_layout 0 35 1 5 H osd_layout 0 36 1 5 H osd_layout 0 37 1 6 H osd_layout 0 38 1 7 H osd_layout 0 39 1 5 H osd_layout 0 40 1 2 H osd_layout 0 41 1 8 H osd_layout 0 42 1 7 H osd_layout 0 43 0 0 H osd_layout 0 44 0 0 H osd_layout 0 45 0 0 H osd_layout 0 46 3 6 H osd_layout 0 47 3 7 H osd_layout 0 48 23 7 H osd_layout 0 49 23 6 H osd_layout 0 50 0 0 H osd_layout 0 51 12 2 H osd_layout 0 52 12 2 H osd_layout 0 53 12 1 H osd_layout 0 54 12 1 H osd_layout 0 55 1 8 H osd_layout 0 56 2 12 H osd_layout 0 57 2 12 H osd_layout 0 58 2 12 H osd_layout 0 59 2 12 H osd_layout 0 60 2 12 H osd_layout 0 61 2 12 H osd_layout 0 62 2 10 H osd_layout 0 63 2 11 H osd_layout 0 64 2 12 H osd_layout 0 65 2 12 H osd_layout 0 66 2 12 H osd_layout 0 67 2 12 H osd_layout 0 68 2 12 H osd_layout 0 69 2 12 H osd_layout 0 70 2 12 H osd_layout 0 71 2 12 H osd_layout 0 72 2 12 H osd_layout 0 73 2 12 H osd_layout 0 74 2 12 H osd_layout 0 75 2 12 H osd_layout 0 76 2 12 H osd_layout 0 77 2 12 H osd_layout 0 78 0 0 H osd_layout 0 79 2 12 H osd_layout 0 80 2 12 H osd_layout 0 81 2 12 H osd_layout 0 82 2 12 H osd_layout 0 83 2 12 H osd_layout 0 84 2 12 H osd_layout 0 85 23 1 H osd_layout 0 86 19 2 H osd_layout 0 87 19 3 H osd_layout 0 88 19 4 H osd_layout 0 89 19 5 H osd_layout 0 90 19 6 H osd_layout 0 91 19 7 H osd_layout 0 92 19 8 H osd_layout 0 93 19 9 H osd_layout 0 94 19 10 H osd_layout 0 95 19 11 H osd_layout 0 96 0 0 H osd_layout 0 97 0 12 H osd_layout 0 98 0 0 H osd_layout 0 99 0 0 H osd_layout 0 100 12 4 H osd_layout 0 101 12 5 H osd_layout 0 102 12 6 H osd_layout 0 103 12 7 H osd_layout 0 104 0 0 H osd_layout 0 105 3 5 H osd_layout 0 106 1 2 H osd_layout 0 107 1 3 H osd_layout 0 108 2 12 H osd_layout 0 109 23 12 H osd_layout 0 110 23 11 H osd_layout 0 111 24 9 H osd_layout 0 112 24 10 H osd_layout 0 113 1 1 H osd_layout 0 114 1 2 H osd_layout 0 115 1 3 H osd_layout 0 116 1 4 H osd_layout 0 117 0 0 H osd_layout 0 118 0 0 H osd_layout 0 119 0 0 H osd_layout 0 120 0 0 H osd_layout 0 121 3 4 H osd_layout 0 122 3 5 H osd_layout 0 123 3 6 H osd_layout 0 124 23 2 H osd_layout 0 125 0 0 H osd_layout 0 126 0 0 H osd_layout 0 127 0 0 H osd_layout 0 128 0 0 H osd_layout 0 129 0 10 H osd_layout 0 130 2 7 H osd_layout 0 131 2 8 H osd_layout 0 132 2 9 H osd_layout 0 133 2 10 H osd_layout 0 134 0 0 H osd_layout 0 135 0 0 H osd_layout 0 136 0 0 H osd_layout 0 137 0 0 H osd_layout 0 138 0 0 H osd_layout 0 139 0 0 H osd_layout 0 140 12 3 H osd_layout 0 141 12 3 H osd_layout 0 142 20 3 H osd_layout 0 143 0 0 H osd_layout 0 144 1 4 H osd_layout 0 145 1 3 H osd_layout 0 146 20 3 H osd_layout 1 0 23 0 H osd_layout 1 1 12 0 H osd_layout 1 2 0 0 H osd_layout 1 3 8 6 H osd_layout 1 4 8 6 H osd_layout 1 5 23 8 H osd_layout 1 6 23 9 H osd_layout 1 7 13 12 H osd_layout 1 8 20 2 H osd_layout 1 9 1 2 H osd_layout 1 10 8 6 H osd_layout 1 11 2 3 H osd_layout 1 12 1 4 H osd_layout 1 13 23 1 H osd_layout 1 14 0 11 H osd_layout 1 15 1 0 H osd_layout 1 16 2 10 H osd_layout 1 17 2 11 H osd_layout 1 18 2 12 H osd_layout 1 19 15 1 H osd_layout 1 20 18 12 H osd_layout 1 21 0 12 H osd_layout 1 22 14 11 H osd_layout 1 23 1 1 H osd_layout 1 24 12 2 H osd_layout 1 25 23 5 H osd_layout 1 26 24 7 H osd_layout 1 27 3 5 H osd_layout 1 28 23 11 H osd_layout 1 29 23 12 H osd_layout 1 30 1 13 H osd_layout 1 31 0 10 H osd_layout 1 32 12 1 H osd_layout 1 33 6 2 H osd_layout 1 34 18 2 H osd_layout 1 35 1 5 H osd_layout 1 36 1 5 H osd_layout 1 37 1 6 H osd_layout 1 38 1 7 H osd_layout 1 39 1 5 H osd_layout 1 40 1 2 H osd_layout 1 41 1 8 H osd_layout 1 42 1 7 H osd_layout 1 43 0 0 H osd_layout 1 44 0 0 H osd_layout 1 45 0 0 H osd_layout 1 46 3 6 H osd_layout 1 47 3 7 H osd_layout 1 48 23 7 H osd_layout 1 49 23 6 H osd_layout 1 50 0 0 H osd_layout 1 51 12 2 H osd_layout 1 52 12 2 H osd_layout 1 53 12 1 H osd_layout 1 54 12 1 H osd_layout 1 55 1 8 H osd_layout 1 56 2 12 H osd_layout 1 57 2 12 H osd_layout 1 58 2 12 H osd_layout 1 59 2 12 H osd_layout 1 60 2 12 H osd_layout 1 61 2 12 H osd_layout 1 62 2 10 H osd_layout 1 63 2 11 H osd_layout 1 64 2 12 H osd_layout 1 65 2 12 H osd_layout 1 66 2 12 H osd_layout 1 67 2 12 H osd_layout 1 68 2 12 H osd_layout 1 69 2 12 H osd_layout 1 70 2 12 H osd_layout 1 71 2 12 H osd_layout 1 72 2 12 H osd_layout 1 73 2 12 H osd_layout 1 74 2 12 H osd_layout 1 75 2 12 H osd_layout 1 76 2 12 H osd_layout 1 77 2 12 H osd_layout 1 78 0 0 H osd_layout 1 79 2 12 H osd_layout 1 80 2 12 H osd_layout 1 81 2 12 H osd_layout 1 82 2 12 H osd_layout 1 83 2 12 H osd_layout 1 84 2 12 H osd_layout 1 85 23 1 H osd_layout 1 86 19 2 H osd_layout 1 87 19 3 H osd_layout 1 88 19 4 H osd_layout 1 89 19 5 H osd_layout 1 90 19 6 H osd_layout 1 91 19 7 H osd_layout 1 92 19 8 H osd_layout 1 93 19 9 H osd_layout 1 94 19 10 H osd_layout 1 95 19 11 H osd_layout 1 96 0 0 H osd_layout 1 97 0 12 H osd_layout 1 98 0 0 H osd_layout 1 99 0 0 H osd_layout 1 100 12 4 H osd_layout 1 101 12 5 H osd_layout 1 102 12 6 H osd_layout 1 103 12 7 H osd_layout 1 104 0 0 H osd_layout 1 105 3 5 H osd_layout 1 106 1 2 H osd_layout 1 107 1 3 H osd_layout 1 108 2 12 H osd_layout 1 109 23 12 H osd_layout 1 110 23 11 H osd_layout 1 111 24 9 H osd_layout 1 112 24 10 H osd_layout 1 113 1 1 H osd_layout 1 114 1 2 H osd_layout 1 115 1 3 H osd_layout 1 116 1 4 H osd_layout 1 117 0 0 H osd_layout 1 118 0 0 H osd_layout 1 119 0 0 H osd_layout 1 120 0 0 H osd_layout 1 121 3 4 H osd_layout 1 122 3 5 H osd_layout 1 123 3 6 H osd_layout 1 124 23 2 H osd_layout 1 125 0 0 H osd_layout 1 126 0 0 H osd_layout 1 127 0 0 H osd_layout 1 128 0 0 H osd_layout 1 129 0 10 H osd_layout 1 130 2 7 H osd_layout 1 131 2 8 H osd_layout 1 132 2 9 H osd_layout 1 133 2 10 H osd_layout 1 134 0 0 H osd_layout 1 135 0 0 H osd_layout 1 136 0 0 H osd_layout 1 137 0 0 H osd_layout 1 138 0 0 H osd_layout 1 139 0 0 H osd_layout 1 140 12 3 H osd_layout 1 141 12 3 H osd_layout 1 142 20 3 H osd_layout 1 143 0 0 H osd_layout 1 144 1 4 H osd_layout 1 145 1 3 H osd_layout 1 146 20 3 H osd_layout 2 0 23 0 H osd_layout 2 1 12 0 H osd_layout 2 2 0 0 H osd_layout 2 3 8 6 H osd_layout 2 4 8 6 H osd_layout 2 5 23 8 H osd_layout 2 6 23 9 H osd_layout 2 7 13 12 H osd_layout 2 8 20 2 H osd_layout 2 9 1 2 H osd_layout 2 10 8 6 H osd_layout 2 11 2 3 H osd_layout 2 12 1 4 H osd_layout 2 13 23 1 H osd_layout 2 14 0 11 H osd_layout 2 15 1 0 H osd_layout 2 16 2 10 H osd_layout 2 17 2 11 H osd_layout 2 18 2 12 H osd_layout 2 19 15 1 H osd_layout 2 20 18 12 H osd_layout 2 21 0 12 H osd_layout 2 22 14 11 H osd_layout 2 23 1 1 H osd_layout 2 24 12 2 H osd_layout 2 25 23 5 H osd_layout 2 26 24 7 H osd_layout 2 27 3 5 H osd_layout 2 28 23 11 H osd_layout 2 29 23 12 H osd_layout 2 30 1 13 H osd_layout 2 31 0 10 H osd_layout 2 32 12 1 H osd_layout 2 33 6 2 H osd_layout 2 34 18 2 H osd_layout 2 35 1 5 H osd_layout 2 36 1 5 H osd_layout 2 37 1 6 H osd_layout 2 38 1 7 H osd_layout 2 39 1 5 H osd_layout 2 40 1 2 H osd_layout 2 41 1 8 H osd_layout 2 42 1 7 H osd_layout 2 43 0 0 H osd_layout 2 44 0 0 H osd_layout 2 45 0 0 H osd_layout 2 46 3 6 H osd_layout 2 47 3 7 H osd_layout 2 48 23 7 H osd_layout 2 49 23 6 H osd_layout 2 50 0 0 H osd_layout 2 51 12 2 H osd_layout 2 52 12 2 H osd_layout 2 53 12 1 H osd_layout 2 54 12 1 H osd_layout 2 55 1 8 H osd_layout 2 56 2 12 H osd_layout 2 57 2 12 H osd_layout 2 58 2 12 H osd_layout 2 59 2 12 H osd_layout 2 60 2 12 H osd_layout 2 61 2 12 H osd_layout 2 62 2 10 H osd_layout 2 63 2 11 H osd_layout 2 64 2 12 H osd_layout 2 65 2 12 H osd_layout 2 66 2 12 H osd_layout 2 67 2 12 H osd_layout 2 68 2 12 H osd_layout 2 69 2 12 H osd_layout 2 70 2 12 H osd_layout 2 71 2 12 H osd_layout 2 72 2 12 H osd_layout 2 73 2 12 H osd_layout 2 74 2 12 H osd_layout 2 75 2 12 H osd_layout 2 76 2 12 H osd_layout 2 77 2 12 H osd_layout 2 78 0 0 H osd_layout 2 79 2 12 H osd_layout 2 80 2 12 H osd_layout 2 81 2 12 H osd_layout 2 82 2 12 H osd_layout 2 83 2 12 H osd_layout 2 84 2 12 H osd_layout 2 85 23 1 H osd_layout 2 86 19 2 H osd_layout 2 87 19 3 H osd_layout 2 88 19 4 H osd_layout 2 89 19 5 H osd_layout 2 90 19 6 H osd_layout 2 91 19 7 H osd_layout 2 92 19 8 H osd_layout 2 93 19 9 H osd_layout 2 94 19 10 H osd_layout 2 95 19 11 H osd_layout 2 96 0 0 H osd_layout 2 97 0 12 H osd_layout 2 98 0 0 H osd_layout 2 99 0 0 H osd_layout 2 100 12 4 H osd_layout 2 101 12 5 H osd_layout 2 102 12 6 H osd_layout 2 103 12 7 H osd_layout 2 104 0 0 H osd_layout 2 105 3 5 H osd_layout 2 106 1 2 H osd_layout 2 107 1 3 H osd_layout 2 108 2 12 H osd_layout 2 109 23 12 H osd_layout 2 110 23 11 H osd_layout 2 111 24 9 H osd_layout 2 112 24 10 H osd_layout 2 113 1 1 H osd_layout 2 114 1 2 H osd_layout 2 115 1 3 H osd_layout 2 116 1 4 H osd_layout 2 117 0 0 H osd_layout 2 118 0 0 H osd_layout 2 119 0 0 H osd_layout 2 120 0 0 H osd_layout 2 121 3 4 H osd_layout 2 122 3 5 H osd_layout 2 123 3 6 H osd_layout 2 124 23 2 H osd_layout 2 125 0 0 H osd_layout 2 126 0 0 H osd_layout 2 127 0 0 H osd_layout 2 128 0 0 H osd_layout 2 129 0 10 H osd_layout 2 130 2 7 H osd_layout 2 131 2 8 H osd_layout 2 132 2 9 H osd_layout 2 133 2 10 H osd_layout 2 134 0 0 H osd_layout 2 135 0 0 H osd_layout 2 136 0 0 H osd_layout 2 137 0 0 H osd_layout 2 138 0 0 H osd_layout 2 139 0 0 H osd_layout 2 140 12 3 H osd_layout 2 141 12 3 H osd_layout 2 142 20 3 H osd_layout 2 143 0 0 H osd_layout 2 144 1 4 H osd_layout 2 145 1 3 H osd_layout 2 146 20 3 H osd_layout 3 0 23 0 H osd_layout 3 1 12 0 H osd_layout 3 2 0 0 H osd_layout 3 3 8 6 H osd_layout 3 4 8 6 H osd_layout 3 5 23 8 H osd_layout 3 6 23 9 H osd_layout 3 7 13 12 H osd_layout 3 8 20 2 H osd_layout 3 9 1 2 H osd_layout 3 10 8 6 H osd_layout 3 11 2 3 H osd_layout 3 12 1 4 H osd_layout 3 13 23 1 H osd_layout 3 14 0 11 H osd_layout 3 15 1 0 H osd_layout 3 16 2 10 H osd_layout 3 17 2 11 H osd_layout 3 18 2 12 H osd_layout 3 19 15 1 H osd_layout 3 20 18 12 H osd_layout 3 21 0 12 H osd_layout 3 22 14 11 H osd_layout 3 23 1 1 H osd_layout 3 24 12 2 H osd_layout 3 25 23 5 H osd_layout 3 26 24 7 H osd_layout 3 27 3 5 H osd_layout 3 28 23 11 H osd_layout 3 29 23 12 H osd_layout 3 30 1 13 H osd_layout 3 31 0 10 H osd_layout 3 32 12 1 H osd_layout 3 33 6 2 H osd_layout 3 34 18 2 H osd_layout 3 35 1 5 H osd_layout 3 36 1 5 H osd_layout 3 37 1 6 H osd_layout 3 38 1 7 H osd_layout 3 39 1 5 H osd_layout 3 40 1 2 H osd_layout 3 41 1 8 H osd_layout 3 42 1 7 H osd_layout 3 43 0 0 H osd_layout 3 44 0 0 H osd_layout 3 45 0 0 H osd_layout 3 46 3 6 H osd_layout 3 47 3 7 H osd_layout 3 48 23 7 H osd_layout 3 49 23 6 H osd_layout 3 50 0 0 H osd_layout 3 51 12 2 H osd_layout 3 52 12 2 H osd_layout 3 53 12 1 H osd_layout 3 54 12 1 H osd_layout 3 55 1 8 H osd_layout 3 56 2 12 H osd_layout 3 57 2 12 H osd_layout 3 58 2 12 H osd_layout 3 59 2 12 H osd_layout 3 60 2 12 H osd_layout 3 61 2 12 H osd_layout 3 62 2 10 H osd_layout 3 63 2 11 H osd_layout 3 64 2 12 H osd_layout 3 65 2 12 H osd_layout 3 66 2 12 H osd_layout 3 67 2 12 H osd_layout 3 68 2 12 H osd_layout 3 69 2 12 H osd_layout 3 70 2 12 H osd_layout 3 71 2 12 H osd_layout 3 72 2 12 H osd_layout 3 73 2 12 H osd_layout 3 74 2 12 H osd_layout 3 75 2 12 H osd_layout 3 76 2 12 H osd_layout 3 77 2 12 H osd_layout 3 78 0 0 H osd_layout 3 79 2 12 H osd_layout 3 80 2 12 H osd_layout 3 81 2 12 H osd_layout 3 82 2 12 H osd_layout 3 83 2 12 H osd_layout 3 84 2 12 H osd_layout 3 85 23 1 H osd_layout 3 86 19 2 H osd_layout 3 87 19 3 H osd_layout 3 88 19 4 H osd_layout 3 89 19 5 H osd_layout 3 90 19 6 H osd_layout 3 91 19 7 H osd_layout 3 92 19 8 H osd_layout 3 93 19 9 H osd_layout 3 94 19 10 H osd_layout 3 95 19 11 H osd_layout 3 96 0 0 H osd_layout 3 97 0 12 H osd_layout 3 98 0 0 H osd_layout 3 99 0 0 H osd_layout 3 100 12 4 H osd_layout 3 101 12 5 H osd_layout 3 102 12 6 H osd_layout 3 103 12 7 H osd_layout 3 104 0 0 H osd_layout 3 105 3 5 H osd_layout 3 106 1 2 H osd_layout 3 107 1 3 H osd_layout 3 108 2 12 H osd_layout 3 109 23 12 H osd_layout 3 110 23 11 H osd_layout 3 111 24 9 H osd_layout 3 112 24 10 H osd_layout 3 113 1 1 H osd_layout 3 114 1 2 H osd_layout 3 115 1 3 H osd_layout 3 116 1 4 H osd_layout 3 117 0 0 H osd_layout 3 118 0 0 H osd_layout 3 119 0 0 H osd_layout 3 120 0 0 H osd_layout 3 121 3 4 H osd_layout 3 122 3 5 H osd_layout 3 123 3 6 H osd_layout 3 124 23 2 H osd_layout 3 125 0 0 H osd_layout 3 126 0 0 H osd_layout 3 127 0 0 H osd_layout 3 128 0 0 H osd_layout 3 129 0 10 H osd_layout 3 130 2 7 H osd_layout 3 131 2 8 H osd_layout 3 132 2 9 H osd_layout 3 133 2 10 H osd_layout 3 134 0 0 H osd_layout 3 135 0 0 H osd_layout 3 136 0 0 H osd_layout 3 137 0 0 H osd_layout 3 138 0 0 H osd_layout 3 139 0 0 H osd_layout 3 140 12 3 H osd_layout 3 141 12 3 H osd_layout 3 142 20 3 H osd_layout 3 143 0 0 H osd_layout 3 144 1 4 H osd_layout 3 145 1 3 H osd_layout 3 146 20 3 H

Programming: logic

logic 0 0 -1 0 0 0 0 0 0 logic 1 0 -1 0 0 0 0 0 0 logic 2 0 -1 0 0 0 0 0 0 logic 3 0 -1 0 0 0 0 0 0 logic 4 0 -1 0 0 0 0 0 0 logic 5 0 -1 0 0 0 0 0 0 logic 6 0 -1 0 0 0 0 0 0 logic 7 0 -1 0 0 0 0 0 0 logic 8 0 -1 0 0 0 0 0 0 logic 9 0 -1 0 0 0 0 0 0 logic 10 0 -1 0 0 0 0 0 0 logic 11 0 -1 0 0 0 0 0 0 logic 12 0 -1 0 0 0 0 0 0 logic 13 0 -1 0 0 0 0 0 0 logic 14 0 -1 0 0 0 0 0 0 logic 15 0 -1 0 0 0 0 0 0 logic 16 0 -1 0 0 0 0 0 0 logic 17 0 -1 0 0 0 0 0 0 logic 18 0 -1 0 0 0 0 0 0 logic 19 0 -1 0 0 0 0 0 0 logic 20 0 -1 0 0 0 0 0 0 logic 21 0 -1 0 0 0 0 0 0 logic 22 0 -1 0 0 0 0 0 0 logic 23 0 -1 0 0 0 0 0 0 logic 24 0 -1 0 0 0 0 0 0 logic 25 0 -1 0 0 0 0 0 0 logic 26 0 -1 0 0 0 0 0 0 logic 27 0 -1 0 0 0 0 0 0 logic 28 0 -1 0 0 0 0 0 0 logic 29 0 -1 0 0 0 0 0 0 logic 30 0 -1 0 0 0 0 0 0 logic 31 0 -1 0 0 0 0 0 0 logic 32 0 -1 0 0 0 0 0 0 logic 33 0 -1 0 0 0 0 0 0 logic 34 0 -1 0 0 0 0 0 0 logic 35 0 -1 0 0 0 0 0 0 logic 36 0 -1 0 0 0 0 0 0 logic 37 0 -1 0 0 0 0 0 0 logic 38 0 -1 0 0 0 0 0 0 logic 39 0 -1 0 0 0 0 0 0 logic 40 0 -1 0 0 0 0 0 0 logic 41 0 -1 0 0 0 0 0 0 logic 42 0 -1 0 0 0 0 0 0 logic 43 0 -1 0 0 0 0 0 0 logic 44 0 -1 0 0 0 0 0 0 logic 45 0 -1 0 0 0 0 0 0 logic 46 0 -1 0 0 0 0 0 0 logic 47 0 -1 0 0 0 0 0 0 logic 48 0 -1 0 0 0 0 0 0 logic 49 0 -1 0 0 0 0 0 0 logic 50 0 -1 0 0 0 0 0 0 logic 51 0 -1 0 0 0 0 0 0 logic 52 0 -1 0 0 0 0 0 0 logic 53 0 -1 0 0 0 0 0 0 logic 54 0 -1 0 0 0 0 0 0 logic 55 0 -1 0 0 0 0 0 0 logic 56 0 -1 0 0 0 0 0 0 logic 57 0 -1 0 0 0 0 0 0 logic 58 0 -1 0 0 0 0 0 0 logic 59 0 -1 0 0 0 0 0 0 logic 60 0 -1 0 0 0 0 0 0 logic 61 0 -1 0 0 0 0 0 0 logic 62 0 -1 0 0 0 0 0 0 logic 63 0 -1 0 0 0 0 0 0

Programming: global variables

gvar 0 0 -32768 32767 gvar 1 0 -32768 32767 gvar 2 0 -32768 32767 gvar 3 0 -32768 32767 gvar 4 0 -32768 32767 gvar 5 0 -32768 32767 gvar 6 0 -32768 32767 gvar 7 0 -32768 32767

Programming: PID controllers

pid 0 0 0 0 0 0 0 0 0 0 pid 1 0 0 0 0 0 0 0 0 0 pid 2 0 0 0 0 0 0 0 0 0 pid 3 0 0 0 0 0 0 0 0 0

master

set looptime = 1000 set gyro_hardware_lpf = 256HZ set gyro_anti_aliasing_lpf_hz = 250 set gyro_anti_aliasing_lpf_type = PT1 set gyro_main_lpf_hz = 25 set gyro_main_lpf_type = BIQUAD set gyro_use_dyn_lpf = OFF set gyro_dyn_lpf_min_hz = 200 set gyro_dyn_lpf_max_hz = 500 set gyro_dyn_lpf_curve_expo = 5 set dynamic_gyro_notch_enabled = ON set dynamic_gyro_notch_q = 250 set dynamic_gyro_notch_min_hz = 30 set dynamic_gyro_notch_mode = 2D set dynamic_gyro_notch_3d_q = 200 set setpoint_kalman_enabled = ON set setpoint_kalman_q = 100 set init_gyro_cal = ON set gyro_zero_x = -6 set gyro_zero_y = 0 set gyro_zero_z = -2 set ins_gravity_cmss = 979.384 set vbat_adc_channel = 1 set rssi_adc_channel = 3 set current_adc_channel = 2 set airspeed_adc_channel = 0 set acc_notch_hz = 0 set acc_notch_cutoff = 1 set acc_hardware = ICM42605 set acc_lpf_hz = 15 set acc_lpf_type = BIQUAD set acczero_x = -2 set acczero_y = 3 set acczero_z = 13 set accgain_x = 4095 set accgain_y = 4095 set accgain_z = 4095 set rangefinder_hardware = NONE set rangefinder_median_filter = OFF set opflow_hardware = NONE set opflow_scale = 10.500 set align_opflow = CW0FLIP set align_mag = CW270FLIP set mag_hardware = NONE set mag_declination = 0 set magzero_x = 0 set magzero_y = 0 set magzero_z = 0 set maggain_x = 1024 set maggain_y = 1024 set maggain_z = 1024 set mag_calibration_time = 30 set align_mag_roll = 0 set align_mag_pitch = 0 set align_mag_yaw = 0 set baro_hardware = SPL06 set baro_cal_tolerance = 150 set pitot_hardware = NONE set pitot_lpf_milli_hz = 350 set pitot_scale = 1.000 set receiver_type = SERIAL set min_check = 1100 set max_check = 1900 set rssi_source = AUTO set rssi_channel = 0 set rssi_min = 0 set rssi_max = 100 set sbus_sync_interval = 3000 set rc_filter_lpf_hz = 50 set rc_filter_auto = ON set rc_filter_smoothing_factor = 30 set serialrx_provider = CRSF set serialrx_inverted = OFF set spektrum_sat_bind = 0 set srxl2_unit_id = 1 set srxl2_baud_fast = ON set rx_min_usec = 885 set rx_max_usec = 2115 set serialrx_halfduplex = OFF set blackbox_rate_num = 1 set blackbox_rate_denom = 1 set blackbox_device = SDCARD set sdcard_detect_inverted = OFF set max_throttle = 1850 set min_command = 1000 set motor_pwm_rate = 16000 set motor_pwm_protocol = STANDARD set motor_poles = 14 set failsafe_delay = 5 set failsafe_recovery_delay = 5 set failsafe_off_delay = 200 set failsafe_throttle_low_delay = 0 set failsafe_procedure = LAND set failsafe_stick_threshold = 50 set failsafe_fw_roll_angle = -200 set failsafe_fw_pitch_angle = 100 set failsafe_fw_yaw_rate = -45 set failsafe_min_distance = 0 set failsafe_min_distance_procedure = DROP set failsafe_mission_delay = 0 set align_board_roll = 0 set align_board_pitch = 0 set align_board_yaw = 0 set vbat_meter_type = ADC set vbat_scale = 1100 set current_meter_scale = 150 set current_meter_offset = 0 set current_meter_type = ADC set bat_voltage_src = RAW set cruise_power = 0 set idle_power = 0 set rth_energy_margin = 5 set thr_comp_weight = 1.000 set 3d_deadband_low = 1406 set 3d_deadband_high = 1514 set 3d_neutral = 1460 set servo_protocol = PWM set servo_center_pulse = 1500 set servo_pwm_rate = 50 set servo_lpf_hz = 20 set flaperon_throw_offset = 200 set tri_unarmed_servo = ON set servo_autotrim_rotation_limit = 15 set reboot_character = 82 set ahrs_dcm_kp = 2000 set ahrs_dcm_ki = 50 set ahrs_dcm_kp_mag = 2000 set ahrs_dcm_ki_mag = 50 set small_angle = 180 set ahrs_acc_ignore_rate = 15 set ahrs_acc_ignore_slope = 5 set ahrs_gps_yaw_windcomp = ON set ahrs_inertia_comp_method = ADAPTIVE set fixed_wing_auto_arm = OFF set disarm_kill_switch = ON set switch_disarm_delay = 250 set prearm_timeout = 10000 set applied_defaults = 3 set rpm_gyro_filter_enabled = OFF set rpm_gyro_harmonics = 1 set rpm_gyro_min_hz = 100 set rpm_gyro_q = 500 set gps_provider = UBLOX set gps_sbas_mode = NONE set gps_dyn_model = AIR_1G set gps_auto_config = ON set gps_auto_baud = ON set gps_auto_baud_max_supported = 230400 set gps_ublox_use_galileo = OFF set gps_ublox_use_beidou = OFF set gps_ublox_use_glonass = OFF set gps_min_sats = 6 set gps_ublox_nav_hz = 10 set deadband = 5 set yaw_deadband = 5 set pos_hold_deadband = 10 set control_deadband = 10 set alt_hold_deadband = 50 set 3d_deadband_throttle = 50 set airmode_type = STICK_CENTER_ONCE set airmode_throttle_threshold = 1150 set fw_autotune_min_stick = 50 set fw_autotune_rate_adjustment = AUTO set fw_autotune_max_rate_deflection = 80 set inav_auto_mag_decl = ON set inav_gravity_cal_tolerance = 5 set inav_use_gps_velned = ON set inav_use_gps_no_baro = OFF set inav_allow_dead_reckoning = OFF set inav_reset_altitude = FIRST_ARM set inav_reset_home = FIRST_ARM set inav_max_surface_altitude = 200 set inav_w_z_surface_p = 3.500 set inav_w_z_surface_v = 6.100 set inav_w_xy_flow_p = 1.000 set inav_w_xy_flow_v = 2.000 set inav_w_z_baro_p = 0.350 set inav_w_z_gps_p = 0.200 set inav_w_z_gps_v = 0.100 set inav_w_xy_gps_p = 1.000 set inav_w_xy_gps_v = 2.000 set inav_w_z_res_v = 0.500 set inav_w_xy_res_v = 0.500 set inav_w_xyz_acc_p = 1.000 set inav_w_acc_bias = 0.010 set inav_max_eph_epv = 1000.000 set inav_baro_epv = 100.000 set nav_disarm_on_landing = ON set nav_land_detect_sensitivity = 5 set nav_landing_bump_detection = OFF set nav_mc_althold_throttle = STICK set nav_extra_arming_safety = ALLOW_BYPASS set nav_user_control_mode = ATTI set nav_position_timeout = 5 set nav_wp_load_on_boot = OFF set nav_wp_radius = 5000 set nav_wp_enforce_altitude = 0 set nav_wp_max_safe_distance = 500 set nav_wp_mission_restart = RESUME set nav_wp_multi_mission_index = 1 set nav_fw_wp_tracking_accuracy = 0 set nav_fw_wp_tracking_max_angle = 60 set nav_fw_wp_turn_smoothing = OFF set nav_auto_speed = 300 set nav_max_auto_speed = 1000 set nav_auto_climb_rate = 500 set nav_manual_speed = 500 set nav_manual_climb_rate = 200 set nav_land_minalt_vspd = 50 set nav_land_maxalt_vspd = 200 set nav_land_slowdown_minalt = 500 set nav_land_slowdown_maxalt = 2000 set nav_emerg_landing_speed = 500 set nav_min_rth_distance = 500 set nav_overrides_motor_stop = ALL_NAV set nav_fw_soaring_motor_stop = OFF set nav_fw_soaring_pitch_deadband = 5 set nav_rth_climb_first = ON set nav_rth_climb_first_stage_mode = AT_LEAST set nav_rth_climb_first_stage_altitude = 0 set nav_rth_climb_ignore_emerg = OFF set nav_rth_tail_first = OFF set nav_rth_allow_landing = FS_ONLY set nav_rth_alt_mode = AT_LEAST set nav_rth_alt_control_override = OFF set nav_rth_abort_threshold = 50000 set nav_max_terrain_follow_alt = 100 set nav_max_altitude = 0 set nav_rth_altitude = 5000 set nav_rth_home_altitude = 0 set nav_rth_linear_descent_start_distance = 0 set nav_rth_use_linear_descent = OFF set nav_rth_trackback_mode = OFF set nav_rth_trackback_distance = 500 set safehome_max_distance = 20000 set safehome_usage_mode = RTH set nav_mission_planner_reset = ON set nav_cruise_yaw_rate = 20 set nav_mc_bank_angle = 30 set nav_auto_disarm_delay = 1000 set nav_mc_braking_speed_threshold = 100 set nav_mc_braking_disengage_speed = 75 set nav_mc_braking_timeout = 2000 set nav_mc_braking_boost_factor = 100 set nav_mc_braking_boost_timeout = 750 set nav_mc_braking_boost_speed_threshold = 150 set nav_mc_braking_boost_disengage_speed = 100 set nav_mc_braking_bank_angle = 40 set nav_mc_pos_deceleration_time = 120 set nav_mc_pos_expo = 10 set nav_mc_wp_slowdown = ON set nav_fw_bank_angle = 35 set nav_fw_climb_angle = 20 set nav_fw_dive_angle = 15 set nav_fw_pitch2thr_smoothing = 6 set fw_min_throttle_down_pitch = 0 set nav_fw_pitch2thr_threshold = 50 set nav_fw_loiter_radius = 7500 set fw_loiter_direction = RIGHT set nav_fw_cruise_speed = 0 set nav_fw_control_smoothness = 2 set nav_fw_land_dive_angle = 2 set nav_fw_launch_velocity = 300 set nav_fw_launch_accel = 1863 set nav_fw_launch_max_angle = 45 set nav_fw_launch_detect_time = 40 set nav_fw_launch_idle_motor_delay = 0 set nav_fw_launch_motor_delay = 100 set nav_fw_launch_spinup_time = 100 set nav_fw_launch_end_time = 3000 set nav_fw_launch_min_time = 0 set nav_fw_launch_timeout = 5000 set nav_fw_launch_max_altitude = 5000 set nav_fw_launch_climb_angle = 25 set nav_fw_launch_manual_throttle = OFF set nav_fw_launch_abort_deadband = 100 set nav_fw_allow_manual_thr_increase = OFF set nav_use_fw_yaw_control = OFF set nav_fw_yaw_deadband = 0 set telemetry_switch = ON set telemetry_inverted = OFF set frsky_pitch_roll = OFF set report_cell_voltage = OFF set hott_alarm_sound_interval = 5 set telemetry_halfduplex = ON set smartport_fuel_unit = MAH set ibus_telemetry_type = 0 set ltm_update_rate = NORMAL set sim_ground_station_number = set sim_pin = 0000 set sim_transmit_interval = 60 set sim_transmit_flags = 2 set acc_event_threshold_high = 0 set acc_event_threshold_low = 0 set acc_event_threshold_neg_x = 0 set sim_low_altitude = -32767 set mavlink_ext_status_rate = 2 set mavlink_rc_chan_rate = 5 set mavlink_pos_rate = 2 set mavlink_extra1_rate = 10 set mavlink_extra2_rate = 2 set mavlink_extra3_rate = 1 set mavlink_version = 2 set ledstrip_visual_beeper = OFF set osd_telemetry = OFF set osd_video_system = AUTO set osd_row_shiftdown = 0 set osd_msp_displayport_fullframe_interval = 10 set osd_units = METRIC set osd_stats_energy_unit = MAH set osd_stats_min_voltage_unit = BATTERY set osd_stats_page_auto_swap_time = 3 set osd_rssi_alarm = 20 set osd_time_alarm = 10 set osd_alt_alarm = 100 set osd_dist_alarm = 1000 set osd_neg_alt_alarm = 5 set osd_current_alarm = 0 set osd_gforce_alarm = 5.000 set osd_gforce_axis_alarm_min = -5.000 set osd_gforce_axis_alarm_max = 5.000 set osd_imu_temp_alarm_min = -200 set osd_imu_temp_alarm_max = 600 set osd_esc_temp_alarm_max = 900 set osd_esc_temp_alarm_min = -200 set osd_baro_temp_alarm_min = -200 set osd_baro_temp_alarm_max = 600 set osd_snr_alarm = 4 set osd_link_quality_alarm = 70 set osd_rssi_dbm_alarm = 0 set osd_rssi_dbm_max = -30 set osd_rssi_dbm_min = -120 set osd_temp_label_align = LEFT set osd_airspeed_alarm_min = 0.000 set osd_airspeed_alarm_max = 0.000 set osd_ahi_reverse_roll = OFF set osd_ahi_max_pitch = 20 set osd_crosshairs_style = DEFAULT set osd_crsf_lq_format = TYPE1 set osd_horizon_offset = 0 set osd_camera_uptilt = 0 set osd_ahi_camera_uptilt_comp = OFF set osd_camera_fov_h = 135 set osd_camera_fov_v = 85 set osd_hud_margin_h = 3 set osd_hud_margin_v = 3 set osd_hud_homing = OFF set osd_hud_homepoint = OFF set osd_hud_radar_disp = 0 set osd_hud_radar_range_min = 3 set osd_hud_radar_range_max = 4000 set osd_hud_radar_alt_difference_display_time = 3 set osd_hud_radar_distance_display_time = 3 set osd_hud_wp_disp = 0 set osd_left_sidebar_scroll = NONE set osd_right_sidebar_scroll = NONE set osd_sidebar_scroll_arrows = OFF set osd_main_voltage_decimals = 1 set osd_coordinate_digits = 9 set osd_estimations_wind_compensation = ON set osd_failsafe_switch_layout = OFF set osd_plus_code_digits = 11 set osd_plus_code_short = 0 set osd_ahi_style = DEFAULT set osd_force_grid = OFF set osd_ahi_bordered = OFF set osd_ahi_width = 132 set osd_ahi_height = 162 set osd_ahi_vertical_offset = -18 set osd_sidebar_horizontal_offset = 0 set osd_left_sidebar_scroll_step = 0 set osd_right_sidebar_scroll_step = 0 set osd_sidebar_height = 3 set osd_ahi_pitch_interval = 0 set osd_home_position_arm_screen = ON set osd_pan_servo_index = 0 set osd_pan_servo_pwm2centideg = 0 set osd_pan_servo_offcentre_warning = 10 set osd_pan_servo_indicator_show_degrees = OFF set osd_esc_rpm_precision = 3 set osd_mah_precision = 4 set osd_use_pilot_logo = OFF set osd_inav_to_pilot_logo_spacing = 8 set osd_arm_screen_display_time = 1500 set osd_switch_indicator_zero_name = FLAP set osd_switch_indicator_one_name = GEAR set osd_switch_indicator_two_name = CAM set osd_switch_indicator_three_name = LIGT set osd_switch_indicator_zero_channel = 5 set osd_switch_indicator_one_channel = 5 set osd_switch_indicator_two_channel = 5 set osd_switch_indicator_three_channel = 5 set osd_switch_indicators_align_left = ON set osd_system_msg_display_time = 1000 set osd_speed_source = GROUND set i2c_speed = 400KHZ set debug_mode = NONE set throttle_tilt_comp_str = 0 set name = set pilot_name = set mode_range_logic_operator = OR set stats = OFF set stats_total_time = 0 set stats_total_dist = 0 set stats_total_energy = 0 set tz_offset = 0 set tz_automatic_dst = OFF set display_force_sw_blink = OFF set vtx_halfduplex = ON set vtx_smartaudio_early_akk_workaround = ON set vtx_smartaudio_alternate_softserial_method = ON set vtx_softserial_shortstop = OFF set vtx_smartaudio_stopbits = 2 set vtx_band = 1 set vtx_channel = 1 set vtx_power = 1 set vtx_low_power_disarm = OFF set vtx_pit_mode_chan = 1 set vtx_max_power_override = 0 set vtx_frequency_group = FREQUENCYGROUP_5G8 set log_level = ERROR set log_topics = 0 set esc_sensor_listen_only = OFF set smartport_master_halfduplex = ON set smartport_master_inverted = OFF set dji_workarounds = 1 set dji_use_name_for_messages = ON set dji_esc_temp_source = ESC set dji_message_speed_source = 3D set dji_rssi_source = RSSI set dji_use_adjustments = OFF set dji_cn_alternating_duration = 30 set dshot_beeper_enabled = ON set dshot_beeper_tone = 1 set beeper_pwm_mode = OFF set limit_pi_p = 100 set limit_pi_i = 100 set limit_attn_filter_cutoff = 1.200 set led_pin_pwm_mode = SHARED_LOW set osd_joystick_enabled = OFF set osd_joystick_down = 0 set osd_joystick_up = 48 set osd_joystick_left = 63 set osd_joystick_right = 28 set osd_joystick_enter = 75

mixer_profile

mixer_profile 1

set motor_direction_inverted = OFF set platform_type = AIRPLANE set has_flaps = ON set model_preview_type = 14 set motorstop_on_low = ON set mixer_pid_profile_linking = OFF set mixer_automated_switch = OFF set mixer_switch_trans_timer = 0

Mixer: motor mixer

mmix reset

mmix 0 1.000 0.000 0.000 0.000

Mixer: servo mixer

smix reset

smix 0 1 1 100 0 -1 smix 1 2 0 100 0 -1 smix 2 3 0 100 0 -1 smix 3 4 2 100 0 -1 smix 4 2 14 100 50 -1 smix 5 3 14 -100 50 -1 smix 6 5 15 100 25 -1 smix 7 6 15 100 25 -1

profile

profile 1

set mc_p_pitch = 40 set mc_i_pitch = 30 set mc_d_pitch = 23 set mc_cd_pitch = 60 set mc_p_roll = 40 set mc_i_roll = 30 set mc_d_roll = 23 set mc_cd_roll = 60 set mc_p_yaw = 85 set mc_i_yaw = 45 set mc_d_yaw = 0 set mc_cd_yaw = 60 set mc_p_level = 20 set mc_i_level = 15 set mc_d_level = 75 set fw_p_pitch = 15 set fw_i_pitch = 5 set fw_d_pitch = 5 set fw_ff_pitch = 80 set fw_p_roll = 15 set fw_i_roll = 3 set fw_d_roll = 7 set fw_ff_roll = 50 set fw_p_yaw = 50 set fw_i_yaw = 0 set fw_d_yaw = 20 set fw_ff_yaw = 255 set fw_p_level = 20 set fw_i_level = 5 set fw_d_level = 75 set max_angle_inclination_rll = 450 set max_angle_inclination_pit = 300 set dterm_lpf_hz = 10 set dterm_lpf_type = PT2 set yaw_lpf_hz = 0 set fw_reference_airspeed = 1500.000 set fw_turn_assist_yaw_gain = 1.000 set fw_turn_assist_pitch_gain = 0.400 set fw_iterm_limit_stick_position = 0.500 set fw_yaw_iterm_freeze_bank_angle = 0 set pidsum_limit = 500 set pidsum_limit_yaw = 350 set iterm_windup = 50 set pid_iterm_limit_percent = 33 set rate_accel_limit_roll_pitch = 0 set rate_accel_limit_yaw = 10000 set heading_hold_rate_limit = 90 set nav_mc_pos_z_p = 50 set nav_mc_vel_z_p = 100 set nav_mc_vel_z_i = 50 set nav_mc_vel_z_d = 10 set nav_mc_pos_xy_p = 65 set nav_mc_vel_xy_p = 40 set nav_mc_vel_xy_i = 15 set nav_mc_vel_xy_d = 100 set nav_mc_vel_xy_ff = 40 set nav_mc_heading_p = 60 set nav_mc_vel_xy_dterm_lpf_hz = 2.000 set nav_mc_vel_xy_dterm_attenuation = 90 set nav_mc_vel_xy_dterm_attenuation_start = 10 set nav_mc_vel_xy_dterm_attenuation_end = 60 set nav_fw_pos_z_p = 25 set nav_fw_pos_z_i = 5 set nav_fw_pos_z_d = 8 set nav_fw_pos_xy_p = 55 set nav_fw_pos_xy_i = 5 set nav_fw_pos_xy_d = 8 set nav_fw_heading_p = 60 set nav_fw_pos_hdg_p = 30 set nav_fw_pos_hdg_i = 2 set nav_fw_pos_hdg_d = 0 set nav_fw_pos_hdg_pidsum_limit = 350 set mc_iterm_relax = RP set mc_iterm_relax_cutoff = 15 set d_boost_min = 1.000 set d_boost_max = 1.000 set d_boost_max_at_acceleration = 7500.000 set d_boost_gyro_delta_lpf_hz = 80 set antigravity_gain = 1.000 set antigravity_accelerator = 1.000 set antigravity_cutoff_lpf_hz = 15 set pid_type = AUTO set mc_cd_lpf_hz = 30 set fw_level_pitch_trim = 0.000 set smith_predictor_strength = 0.500 set smith_predictor_delay = 0.000 set smith_predictor_lpf_hz = 50 set fw_level_pitch_gain = 5.000 set thr_mid = 50 set thr_expo = 0 set tpa_rate = 0 set tpa_breakpoint = 1500 set tpa_on_yaw = OFF set fw_tpa_time_constant = 1500 set rc_expo = 30 set rc_yaw_expo = 30 set roll_rate = 18 set pitch_rate = 9 set yaw_rate = 3 set manual_rc_expo = 35 set manual_rc_yaw_expo = 20 set manual_roll_rate = 100 set manual_pitch_rate = 100 set manual_yaw_rate = 100 set fpv_mix_degrees = 0 set rate_dynamics_center_sensitivity = 100 set rate_dynamics_end_sensitivity = 100 set rate_dynamics_center_correction = 10 set rate_dynamics_end_correction = 10 set rate_dynamics_center_weight = 0 set rate_dynamics_end_weight = 0

battery_profile

battery_profile 1

set bat_cells = 0 set vbat_cell_detect_voltage = 425 set vbat_max_cell_voltage = 420 set vbat_min_cell_voltage = 330 set vbat_warning_cell_voltage = 350 set battery_capacity = 0 set battery_capacity_warning = 0 set battery_capacity_critical = 0 set battery_capacity_unit = MAH set controlrate_profile = 0 set throttle_scale = 1.000 set throttle_idle = 5.000 set turtle_mode_power_factor = 55 set failsafe_throttle = 1000 set nav_mc_hover_thr = 1300 set nav_fw_cruise_thr = 1400 set nav_fw_min_thr = 1200 set nav_fw_max_thr = 1700 set nav_fw_pitch2thr = 10 set nav_fw_launch_thr = 1700 set nav_fw_launch_idle_thr = 1000 set limit_cont_current = 0 set limit_burst_current = 0 set limit_burst_current_time = 0 set limit_burst_current_falldown_time = 0 set limit_cont_power = 0 set limit_burst_power = 0 set limit_burst_power_time = 0 set limit_burst_power_falldown_time = 0

save configuration

save

end the command batch

batch end

dump

version

INAV/MATEKF405TE 7.0.0 Dec 5 2023 / 10:30:57 (895a4f31)

GCC-10.3.1 20210824 (release)

start the command batch

batch start

resources

Timer overrides

timer_output_mode 0 AUTO timer_output_mode 1 AUTO timer_output_mode 2 AUTO timer_output_mode 3 AUTO timer_output_mode 4 AUTO timer_output_mode 5 AUTO timer_output_mode 6 AUTO timer_output_mode 7 AUTO timer_output_mode 8 AUTO timer_output_mode 9 AUTO timer_output_mode 10 AUTO timer_output_mode 11 AUTO timer_output_mode 12 AUTO timer_output_mode 13 AUTO

Outputs [servo]

servo 0 1000 2000 1500 100 servo 1 1000 2000 1500 100 servo 2 1000 2000 1500 100 servo 3 1000 2000 1500 100 servo 4 1000 2000 1500 100 servo 5 1000 2000 1500 100 servo 6 1000 2000 1500 100 servo 7 1000 2000 1500 100 servo 8 1000 2000 1500 100 servo 9 1000 2000 1500 100 servo 10 1000 2000 1500 100 servo 11 1000 2000 1500 100 servo 12 1000 2000 1500 100 servo 13 1000 2000 1500 100 servo 14 1000 2000 1500 100 servo 15 1000 2000 1500 100

safehome

safehome 0 0 0 0 safehome 1 0 0 0 safehome 2 0 0 0 safehome 3 0 0 0 safehome 4 0 0 0 safehome 5 0 0 0 safehome 6 0 0 0 safehome 7 0 0 0

features

feature -THR_VBAT_COMP feature -VBAT feature -TX_PROF_SEL feature -BAT_PROF_AUTOSWITCH feature -MOTOR_STOP feature -SOFTSERIAL feature -GPS feature -RPM_FILTERS feature -TELEMETRY feature -CURRENT_METER feature -REVERSIBLE_MOTORS feature -RSSI_ADC feature -LED_STRIP feature -DASHBOARD feature -BLACKBOX feature -TRANSPONDER feature -AIRMODE feature -SUPEREXPO feature -VTX feature -PWM_OUTPUT_ENABLE feature -OSD feature -FW_LAUNCH feature -FW_AUTOTRIM feature VBAT feature TX_PROF_SEL feature TELEMETRY feature CURRENT_METER feature BLACKBOX feature AIRMODE feature OSD

beeper

beeper RUNTIME_CALIBRATION beeper HW_FAILURE beeper RX_LOST beeper RX_LOST_LANDING beeper DISARMING beeper ARMING beeper ARMING_GPS_FIX beeper BAT_CRIT_LOW beeper BAT_LOW beeper GPS_STATUS beeper RX_SET beeper ACTION_SUCCESS beeper ACTION_FAIL beeper READY_BEEP beeper MULTI_BEEPS beeper DISARM_REPEAT beeper ARMED beeper SYSTEM_INIT beeper ON_USB beeper LAUNCH_MODE beeper LAUNCH_MODE_LOW_THROTTLE beeper LAUNCH_MODE_IDLE_START beeper CAM_CONNECTION_OPEN beeper CAM_CONNECTION_CLOSED

blackbox

blackbox -NAV_ACC blackbox NAV_POS blackbox NAV_PID blackbox MAG blackbox ACC blackbox ATTI blackbox RC_DATA blackbox RC_COMMAND blackbox MOTORS blackbox -GYRO_RAW blackbox -PEAKS_R blackbox -PEAKS_P blackbox -PEAKS_Y

Receiver: Channel map

map AETR

Ports

serial 20 1 115200 115200 0 115200 serial 0 1 115200 115200 0 115200 serial 1 64 115200 115200 0 115200 serial 2 0 115200 115200 0 115200 serial 3 0 115200 115200 0 115200 serial 4 0 115200 115200 0 115200 serial 5 0 115200 115200 0 115200

LEDs

led 0 0,0::C:0 led 1 0,0::C:0 led 2 0,0::C:0 led 3 0,0::C:0 led 4 0,0::C:0 led 5 0,0::C:0 led 6 0,0::C:0 led 7 0,0::C:0 led 8 0,0::C:0 led 9 0,0::C:0 led 10 0,0::C:0 led 11 0,0::C:0 led 12 0,0::C:0 led 13 0,0::C:0 led 14 0,0::C:0 led 15 0,0::C:0 led 16 0,0::C:0 led 17 0,0::C:0 led 18 0,0::C:0 led 19 0,0::C:0 led 20 0,0::C:0 led 21 0,0::C:0 led 22 0,0::C:0 led 23 0,0::C:0 led 24 0,0::C:0 led 25 0,0::C:0 led 26 0,0::C:0 led 27 0,0::C:0 led 28 0,0::C:0 led 29 0,0::C:0 led 30 0,0::C:0 led 31 0,0::C:0

LED color

color 0 0,0,0 color 1 0,255,255 color 2 0,0,255 color 3 30,0,255 color 4 60,0,255 color 5 90,0,255 color 6 120,0,255 color 7 150,0,255 color 8 180,0,255 color 9 210,0,255 color 10 240,0,255 color 11 270,0,255 color 12 300,0,255 color 13 330,0,255 color 14 0,0,0 color 15 0,0,0

LED mode_color

mode_color 0 0 1 mode_color 0 1 11 mode_color 0 2 2 mode_color 0 3 13 mode_color 0 4 10 mode_color 0 5 3 mode_color 1 0 5 mode_color 1 1 11 mode_color 1 2 3 mode_color 1 3 13 mode_color 1 4 10 mode_color 1 5 3 mode_color 2 0 10 mode_color 2 1 11 mode_color 2 2 4 mode_color 2 3 13 mode_color 2 4 10 mode_color 2 5 3 mode_color 3 0 8 mode_color 3 1 11 mode_color 3 2 4 mode_color 3 3 13 mode_color 3 4 10 mode_color 3 5 3 mode_color 4 0 7 mode_color 4 1 11 mode_color 4 2 3 mode_color 4 3 13 mode_color 4 4 10 mode_color 4 5 3 mode_color 5 0 9 mode_color 5 1 11 mode_color 5 2 2 mode_color 5 3 13 mode_color 5 4 10 mode_color 5 5 3 mode_color 6 0 6 mode_color 6 1 10 mode_color 6 2 1 mode_color 6 3 0 mode_color 6 4 0 mode_color 6 5 2 mode_color 6 6 3 mode_color 6 7 6 mode_color 6 8 1

Modes [aux]

aux 0 0 0 900 900 aux 1 0 0 900 900 aux 2 0 0 900 900 aux 3 0 0 900 900 aux 4 0 0 900 900 aux 5 0 0 900 900 aux 6 0 0 900 900 aux 7 0 0 900 900 aux 8 0 0 900 900 aux 9 0 0 900 900 aux 10 0 0 900 900 aux 11 0 0 900 900 aux 12 0 0 900 900 aux 13 0 0 900 900 aux 14 0 0 900 900 aux 15 0 0 900 900 aux 16 0 0 900 900 aux 17 0 0 900 900 aux 18 0 0 900 900 aux 19 0 0 900 900 aux 20 0 0 900 900 aux 21 0 0 900 900 aux 22 0 0 900 900 aux 23 0 0 900 900 aux 24 0 0 900 900 aux 25 0 0 900 900 aux 26 0 0 900 900 aux 27 0 0 900 900 aux 28 0 0 900 900 aux 29 0 0 900 900 aux 30 0 0 900 900 aux 31 0 0 900 900 aux 32 0 0 900 900 aux 33 0 0 900 900 aux 34 0 0 900 900 aux 35 0 0 900 900 aux 36 0 0 900 900 aux 37 0 0 900 900 aux 38 0 0 900 900 aux 39 0 0 900 900

Adjustments [adjrange]

adjrange 0 0 0 900 900 0 0 adjrange 1 0 0 900 900 0 0 adjrange 2 0 0 900 900 0 0 adjrange 3 0 0 900 900 0 0 adjrange 4 0 0 900 900 0 0 adjrange 5 0 0 900 900 0 0 adjrange 6 0 0 900 900 0 0 adjrange 7 0 0 900 900 0 0 adjrange 8 0 0 900 900 0 0 adjrange 9 0 0 900 900 0 0 adjrange 10 0 0 900 900 0 0 adjrange 11 0 0 900 900 0 0 adjrange 12 0 0 900 900 0 0 adjrange 13 0 0 900 900 0 0 adjrange 14 0 0 900 900 0 0 adjrange 15 0 0 900 900 0 0 adjrange 16 0 0 900 900 0 0 adjrange 17 0 0 900 900 0 0 adjrange 18 0 0 900 900 0 0 adjrange 19 0 0 900 900 0 0

Receiver rxrange

rxrange 0 1000 2000 rxrange 1 1000 2000 rxrange 2 1000 2000 rxrange 3 1000 2000

temp_sensor

temp_sensor 0 0 0 0 0 0 temp_sensor 1 0 0 0 0 0 temp_sensor 2 0 0 0 0 0 temp_sensor 3 0 0 0 0 0 temp_sensor 4 0 0 0 0 0 temp_sensor 5 0 0 0 0 0 temp_sensor 6 0 0 0 0 0 temp_sensor 7 0 0 0 0 0

Mission Control Waypoints [wp]

wp 0 invalid

wp 0 0 0 0 0 0 0 0 0 wp 1 0 0 0 0 0 0 0 0 wp 2 0 0 0 0 0 0 0 0 wp 3 0 0 0 0 0 0 0 0 wp 4 0 0 0 0 0 0 0 0 wp 5 0 0 0 0 0 0 0 0 wp 6 0 0 0 0 0 0 0 0 wp 7 0 0 0 0 0 0 0 0 wp 8 0 0 0 0 0 0 0 0 wp 9 0 0 0 0 0 0 0 0 wp 10 0 0 0 0 0 0 0 0 wp 11 0 0 0 0 0 0 0 0 wp 12 0 0 0 0 0 0 0 0 wp 13 0 0 0 0 0 0 0 0 wp 14 0 0 0 0 0 0 0 0 wp 15 0 0 0 0 0 0 0 0 wp 16 0 0 0 0 0 0 0 0 wp 17 0 0 0 0 0 0 0 0 wp 18 0 0 0 0 0 0 0 0 wp 19 0 0 0 0 0 0 0 0 wp 20 0 0 0 0 0 0 0 0 wp 21 0 0 0 0 0 0 0 0 wp 22 0 0 0 0 0 0 0 0 wp 23 0 0 0 0 0 0 0 0 wp 24 0 0 0 0 0 0 0 0 wp 25 0 0 0 0 0 0 0 0 wp 26 0 0 0 0 0 0 0 0 wp 27 0 0 0 0 0 0 0 0 wp 28 0 0 0 0 0 0 0 0 wp 29 0 0 0 0 0 0 0 0 wp 30 0 0 0 0 0 0 0 0 wp 31 0 0 0 0 0 0 0 0 wp 32 0 0 0 0 0 0 0 0 wp 33 0 0 0 0 0 0 0 0 wp 34 0 0 0 0 0 0 0 0 wp 35 0 0 0 0 0 0 0 0 wp 36 0 0 0 0 0 0 0 0 wp 37 0 0 0 0 0 0 0 0 wp 38 0 0 0 0 0 0 0 0 wp 39 0 0 0 0 0 0 0 0 wp 40 0 0 0 0 0 0 0 0 wp 41 0 0 0 0 0 0 0 0 wp 42 0 0 0 0 0 0 0 0 wp 43 0 0 0 0 0 0 0 0 wp 44 0 0 0 0 0 0 0 0 wp 45 0 0 0 0 0 0 0 0 wp 46 0 0 0 0 0 0 0 0 wp 47 0 0 0 0 0 0 0 0 wp 48 0 0 0 0 0 0 0 0 wp 49 0 0 0 0 0 0 0 0 wp 50 0 0 0 0 0 0 0 0 wp 51 0 0 0 0 0 0 0 0 wp 52 0 0 0 0 0 0 0 0 wp 53 0 0 0 0 0 0 0 0 wp 54 0 0 0 0 0 0 0 0 wp 55 0 0 0 0 0 0 0 0 wp 56 0 0 0 0 0 0 0 0 wp 57 0 0 0 0 0 0 0 0 wp 58 0 0 0 0 0 0 0 0 wp 59 0 0 0 0 0 0 0 0 wp 60 0 0 0 0 0 0 0 0 wp 61 0 0 0 0 0 0 0 0 wp 62 0 0 0 0 0 0 0 0 wp 63 0 0 0 0 0 0 0 0 wp 64 0 0 0 0 0 0 0 0 wp 65 0 0 0 0 0 0 0 0 wp 66 0 0 0 0 0 0 0 0 wp 67 0 0 0 0 0 0 0 0 wp 68 0 0 0 0 0 0 0 0 wp 69 0 0 0 0 0 0 0 0 wp 70 0 0 0 0 0 0 0 0 wp 71 0 0 0 0 0 0 0 0 wp 72 0 0 0 0 0 0 0 0 wp 73 0 0 0 0 0 0 0 0 wp 74 0 0 0 0 0 0 0 0 wp 75 0 0 0 0 0 0 0 0 wp 76 0 0 0 0 0 0 0 0 wp 77 0 0 0 0 0 0 0 0 wp 78 0 0 0 0 0 0 0 0 wp 79 0 0 0 0 0 0 0 0 wp 80 0 0 0 0 0 0 0 0 wp 81 0 0 0 0 0 0 0 0 wp 82 0 0 0 0 0 0 0 0 wp 83 0 0 0 0 0 0 0 0 wp 84 0 0 0 0 0 0 0 0 wp 85 0 0 0 0 0 0 0 0 wp 86 0 0 0 0 0 0 0 0 wp 87 0 0 0 0 0 0 0 0 wp 88 0 0 0 0 0 0 0 0 wp 89 0 0 0 0 0 0 0 0 wp 90 0 0 0 0 0 0 0 0 wp 91 0 0 0 0 0 0 0 0 wp 92 0 0 0 0 0 0 0 0 wp 93 0 0 0 0 0 0 0 0 wp 94 0 0 0 0 0 0 0 0 wp 95 0 0 0 0 0 0 0 0 wp 96 0 0 0 0 0 0 0 0 wp 97 0 0 0 0 0 0 0 0 wp 98 0 0 0 0 0 0 0 0 wp 99 0 0 0 0 0 0 0 0 wp 100 0 0 0 0 0 0 0 0 wp 101 0 0 0 0 0 0 0 0 wp 102 0 0 0 0 0 0 0 0 wp 103 0 0 0 0 0 0 0 0 wp 104 0 0 0 0 0 0 0 0 wp 105 0 0 0 0 0 0 0 0 wp 106 0 0 0 0 0 0 0 0 wp 107 0 0 0 0 0 0 0 0 wp 108 0 0 0 0 0 0 0 0 wp 109 0 0 0 0 0 0 0 0 wp 110 0 0 0 0 0 0 0 0 wp 111 0 0 0 0 0 0 0 0 wp 112 0 0 0 0 0 0 0 0 wp 113 0 0 0 0 0 0 0 0 wp 114 0 0 0 0 0 0 0 0 wp 115 0 0 0 0 0 0 0 0 wp 116 0 0 0 0 0 0 0 0 wp 117 0 0 0 0 0 0 0 0 wp 118 0 0 0 0 0 0 0 0 wp 119 0 0 0 0 0 0 0 0

OSD [osd_layout]

osd_layout 0 0 23 0 V osd_layout 0 1 12 0 V osd_layout 0 2 0 0 H osd_layout 0 3 8 6 H osd_layout 0 4 8 6 H osd_layout 0 5 23 8 H osd_layout 0 6 23 9 H osd_layout 0 7 13 12 V osd_layout 0 8 20 2 H osd_layout 0 9 1 2 V osd_layout 0 10 8 6 H osd_layout 0 11 2 3 V osd_layout 0 12 1 4 V osd_layout 0 13 23 1 H osd_layout 0 14 0 11 V osd_layout 0 15 1 0 V osd_layout 0 16 2 10 H osd_layout 0 17 2 11 H osd_layout 0 18 2 12 H osd_layout 0 19 15 1 H osd_layout 0 20 18 12 H osd_layout 0 21 0 12 H osd_layout 0 22 14 11 H osd_layout 0 23 1 1 H osd_layout 0 24 12 2 H osd_layout 0 25 23 5 H osd_layout 0 26 24 7 H osd_layout 0 27 3 5 H osd_layout 0 28 23 11 V osd_layout 0 29 23 12 H osd_layout 0 30 1 13 V osd_layout 0 31 0 10 H osd_layout 0 32 12 1 H osd_layout 0 33 6 2 H osd_layout 0 34 18 2 H osd_layout 0 35 1 5 H osd_layout 0 36 1 5 H osd_layout 0 37 1 6 H osd_layout 0 38 1 7 H osd_layout 0 39 1 5 H osd_layout 0 40 1 2 H osd_layout 0 41 1 8 H osd_layout 0 42 1 7 H osd_layout 0 43 0 0 H osd_layout 0 44 0 0 H osd_layout 0 45 0 0 H osd_layout 0 46 3 6 H osd_layout 0 47 3 7 H osd_layout 0 48 23 7 H osd_layout 0 49 23 6 H osd_layout 0 50 0 0 H osd_layout 0 51 12 2 H osd_layout 0 52 12 2 H osd_layout 0 53 12 1 H osd_layout 0 54 12 1 H osd_layout 0 55 1 8 H osd_layout 0 56 2 12 H osd_layout 0 57 2 12 H osd_layout 0 58 2 12 H osd_layout 0 59 2 12 H osd_layout 0 60 2 12 H osd_layout 0 61 2 12 H osd_layout 0 62 2 10 H osd_layout 0 63 2 11 H osd_layout 0 64 2 12 H osd_layout 0 65 2 12 H osd_layout 0 66 2 12 H osd_layout 0 67 2 12 H osd_layout 0 68 2 12 H osd_layout 0 69 2 12 H osd_layout 0 70 2 12 H osd_layout 0 71 2 12 H osd_layout 0 72 2 12 H osd_layout 0 73 2 12 H osd_layout 0 74 2 12 H osd_layout 0 75 2 12 H osd_layout 0 76 2 12 H osd_layout 0 77 2 12 H osd_layout 0 78 0 0 H osd_layout 0 79 2 12 H osd_layout 0 80 2 12 H osd_layout 0 81 2 12 H osd_layout 0 82 2 12 H osd_layout 0 83 2 12 H osd_layout 0 84 2 12 H osd_layout 0 85 23 1 H osd_layout 0 86 19 2 H osd_layout 0 87 19 3 H osd_layout 0 88 19 4 H osd_layout 0 89 19 5 H osd_layout 0 90 19 6 H osd_layout 0 91 19 7 H osd_layout 0 92 19 8 H osd_layout 0 93 19 9 H osd_layout 0 94 19 10 H osd_layout 0 95 19 11 H osd_layout 0 96 0 0 H osd_layout 0 97 0 12 H osd_layout 0 98 0 0 H osd_layout 0 99 0 0 H osd_layout 0 100 12 4 H osd_layout 0 101 12 5 H osd_layout 0 102 12 6 H osd_layout 0 103 12 7 H osd_layout 0 104 0 0 H osd_layout 0 105 3 5 H osd_layout 0 106 1 2 H osd_layout 0 107 1 3 H osd_layout 0 108 2 12 H osd_layout 0 109 23 12 H osd_layout 0 110 23 11 H osd_layout 0 111 24 9 H osd_layout 0 112 24 10 H osd_layout 0 113 1 1 H osd_layout 0 114 1 2 H osd_layout 0 115 1 3 H osd_layout 0 116 1 4 H osd_layout 0 117 0 0 H osd_layout 0 118 0 0 H osd_layout 0 119 0 0 H osd_layout 0 120 0 0 H osd_layout 0 121 3 4 H osd_layout 0 122 3 5 H osd_layout 0 123 3 6 H osd_layout 0 124 23 2 H osd_layout 0 125 0 0 H osd_layout 0 126 0 0 H osd_layout 0 127 0 0 H osd_layout 0 128 0 0 H osd_layout 0 129 0 10 H osd_layout 0 130 2 7 H osd_layout 0 131 2 8 H osd_layout 0 132 2 9 H osd_layout 0 133 2 10 H osd_layout 0 134 0 0 H osd_layout 0 135 0 0 H osd_layout 0 136 0 0 H osd_layout 0 137 0 0 H osd_layout 0 138 0 0 H osd_layout 0 139 0 0 H osd_layout 0 140 12 3 H osd_layout 0 141 12 3 H osd_layout 0 142 20 3 H osd_layout 0 143 0 0 H osd_layout 0 144 1 4 H osd_layout 0 145 1 3 H osd_layout 0 146 20 3 H osd_layout 1 0 23 0 H osd_layout 1 1 12 0 H osd_layout 1 2 0 0 H osd_layout 1 3 8 6 H osd_layout 1 4 8 6 H osd_layout 1 5 23 8 H osd_layout 1 6 23 9 H osd_layout 1 7 13 12 H osd_layout 1 8 20 2 H osd_layout 1 9 1 2 H osd_layout 1 10 8 6 H osd_layout 1 11 2 3 H osd_layout 1 12 1 4 H osd_layout 1 13 23 1 H osd_layout 1 14 0 11 H osd_layout 1 15 1 0 H osd_layout 1 16 2 10 H osd_layout 1 17 2 11 H osd_layout 1 18 2 12 H osd_layout 1 19 15 1 H osd_layout 1 20 18 12 H osd_layout 1 21 0 12 H osd_layout 1 22 14 11 H osd_layout 1 23 1 1 H osd_layout 1 24 12 2 H osd_layout 1 25 23 5 H osd_layout 1 26 24 7 H osd_layout 1 27 3 5 H osd_layout 1 28 23 11 H osd_layout 1 29 23 12 H osd_layout 1 30 1 13 H osd_layout 1 31 0 10 H osd_layout 1 32 12 1 H osd_layout 1 33 6 2 H osd_layout 1 34 18 2 H osd_layout 1 35 1 5 H osd_layout 1 36 1 5 H osd_layout 1 37 1 6 H osd_layout 1 38 1 7 H osd_layout 1 39 1 5 H osd_layout 1 40 1 2 H osd_layout 1 41 1 8 H osd_layout 1 42 1 7 H osd_layout 1 43 0 0 H osd_layout 1 44 0 0 H osd_layout 1 45 0 0 H osd_layout 1 46 3 6 H osd_layout 1 47 3 7 H osd_layout 1 48 23 7 H osd_layout 1 49 23 6 H osd_layout 1 50 0 0 H osd_layout 1 51 12 2 H osd_layout 1 52 12 2 H osd_layout 1 53 12 1 H osd_layout 1 54 12 1 H osd_layout 1 55 1 8 H osd_layout 1 56 2 12 H osd_layout 1 57 2 12 H osd_layout 1 58 2 12 H osd_layout 1 59 2 12 H osd_layout 1 60 2 12 H osd_layout 1 61 2 12 H osd_layout 1 62 2 10 H osd_layout 1 63 2 11 H osd_layout 1 64 2 12 H osd_layout 1 65 2 12 H osd_layout 1 66 2 12 H osd_layout 1 67 2 12 H osd_layout 1 68 2 12 H osd_layout 1 69 2 12 H osd_layout 1 70 2 12 H osd_layout 1 71 2 12 H osd_layout 1 72 2 12 H osd_layout 1 73 2 12 H osd_layout 1 74 2 12 H osd_layout 1 75 2 12 H osd_layout 1 76 2 12 H osd_layout 1 77 2 12 H osd_layout 1 78 0 0 H osd_layout 1 79 2 12 H osd_layout 1 80 2 12 H osd_layout 1 81 2 12 H osd_layout 1 82 2 12 H osd_layout 1 83 2 12 H osd_layout 1 84 2 12 H osd_layout 1 85 23 1 H osd_layout 1 86 19 2 H osd_layout 1 87 19 3 H osd_layout 1 88 19 4 H osd_layout 1 89 19 5 H osd_layout 1 90 19 6 H osd_layout 1 91 19 7 H osd_layout 1 92 19 8 H osd_layout 1 93 19 9 H osd_layout 1 94 19 10 H osd_layout 1 95 19 11 H osd_layout 1 96 0 0 H osd_layout 1 97 0 12 H osd_layout 1 98 0 0 H osd_layout 1 99 0 0 H osd_layout 1 100 12 4 H osd_layout 1 101 12 5 H osd_layout 1 102 12 6 H osd_layout 1 103 12 7 H osd_layout 1 104 0 0 H osd_layout 1 105 3 5 H osd_layout 1 106 1 2 H osd_layout 1 107 1 3 H osd_layout 1 108 2 12 H osd_layout 1 109 23 12 H osd_layout 1 110 23 11 H osd_layout 1 111 24 9 H osd_layout 1 112 24 10 H osd_layout 1 113 1 1 H osd_layout 1 114 1 2 H osd_layout 1 115 1 3 H osd_layout 1 116 1 4 H osd_layout 1 117 0 0 H osd_layout 1 118 0 0 H osd_layout 1 119 0 0 H osd_layout 1 120 0 0 H osd_layout 1 121 3 4 H osd_layout 1 122 3 5 H osd_layout 1 123 3 6 H osd_layout 1 124 23 2 H osd_layout 1 125 0 0 H osd_layout 1 126 0 0 H osd_layout 1 127 0 0 H osd_layout 1 128 0 0 H osd_layout 1 129 0 10 H osd_layout 1 130 2 7 H osd_layout 1 131 2 8 H osd_layout 1 132 2 9 H osd_layout 1 133 2 10 H osd_layout 1 134 0 0 H osd_layout 1 135 0 0 H osd_layout 1 136 0 0 H osd_layout 1 137 0 0 H osd_layout 1 138 0 0 H osd_layout 1 139 0 0 H osd_layout 1 140 12 3 H osd_layout 1 141 12 3 H osd_layout 1 142 20 3 H osd_layout 1 143 0 0 H osd_layout 1 144 1 4 H osd_layout 1 145 1 3 H osd_layout 1 146 20 3 H osd_layout 2 0 23 0 H osd_layout 2 1 12 0 H osd_layout 2 2 0 0 H osd_layout 2 3 8 6 H osd_layout 2 4 8 6 H osd_layout 2 5 23 8 H osd_layout 2 6 23 9 H osd_layout 2 7 13 12 H osd_layout 2 8 20 2 H osd_layout 2 9 1 2 H osd_layout 2 10 8 6 H osd_layout 2 11 2 3 H osd_layout 2 12 1 4 H osd_layout 2 13 23 1 H osd_layout 2 14 0 11 H osd_layout 2 15 1 0 H osd_layout 2 16 2 10 H osd_layout 2 17 2 11 H osd_layout 2 18 2 12 H osd_layout 2 19 15 1 H osd_layout 2 20 18 12 H osd_layout 2 21 0 12 H osd_layout 2 22 14 11 H osd_layout 2 23 1 1 H osd_layout 2 24 12 2 H osd_layout 2 25 23 5 H osd_layout 2 26 24 7 H osd_layout 2 27 3 5 H osd_layout 2 28 23 11 H osd_layout 2 29 23 12 H osd_layout 2 30 1 13 H osd_layout 2 31 0 10 H osd_layout 2 32 12 1 H osd_layout 2 33 6 2 H osd_layout 2 34 18 2 H osd_layout 2 35 1 5 H osd_layout 2 36 1 5 H osd_layout 2 37 1 6 H osd_layout 2 38 1 7 H osd_layout 2 39 1 5 H osd_layout 2 40 1 2 H osd_layout 2 41 1 8 H osd_layout 2 42 1 7 H osd_layout 2 43 0 0 H osd_layout 2 44 0 0 H osd_layout 2 45 0 0 H osd_layout 2 46 3 6 H osd_layout 2 47 3 7 H osd_layout 2 48 23 7 H osd_layout 2 49 23 6 H osd_layout 2 50 0 0 H osd_layout 2 51 12 2 H osd_layout 2 52 12 2 H osd_layout 2 53 12 1 H osd_layout 2 54 12 1 H osd_layout 2 55 1 8 H osd_layout 2 56 2 12 H osd_layout 2 57 2 12 H osd_layout 2 58 2 12 H osd_layout 2 59 2 12 H osd_layout 2 60 2 12 H osd_layout 2 61 2 12 H osd_layout 2 62 2 10 H osd_layout 2 63 2 11 H osd_layout 2 64 2 12 H osd_layout 2 65 2 12 H osd_layout 2 66 2 12 H osd_layout 2 67 2 12 H osd_layout 2 68 2 12 H osd_layout 2 69 2 12 H osd_layout 2 70 2 12 H osd_layout 2 71 2 12 H osd_layout 2 72 2 12 H osd_layout 2 73 2 12 H osd_layout 2 74 2 12 H osd_layout 2 75 2 12 H osd_layout 2 76 2 12 H osd_layout 2 77 2 12 H osd_layout 2 78 0 0 H osd_layout 2 79 2 12 H osd_layout 2 80 2 12 H osd_layout 2 81 2 12 H osd_layout 2 82 2 12 H osd_layout 2 83 2 12 H osd_layout 2 84 2 12 H osd_layout 2 85 23 1 H osd_layout 2 86 19 2 H osd_layout 2 87 19 3 H osd_layout 2 88 19 4 H osd_layout 2 89 19 5 H osd_layout 2 90 19 6 H osd_layout 2 91 19 7 H osd_layout 2 92 19 8 H osd_layout 2 93 19 9 H osd_layout 2 94 19 10 H osd_layout 2 95 19 11 H osd_layout 2 96 0 0 H osd_layout 2 97 0 12 H osd_layout 2 98 0 0 H osd_layout 2 99 0 0 H osd_layout 2 100 12 4 H osd_layout 2 101 12 5 H osd_layout 2 102 12 6 H osd_layout 2 103 12 7 H osd_layout 2 104 0 0 H osd_layout 2 105 3 5 H osd_layout 2 106 1 2 H osd_layout 2 107 1 3 H osd_layout 2 108 2 12 H osd_layout 2 109 23 12 H osd_layout 2 110 23 11 H osd_layout 2 111 24 9 H osd_layout 2 112 24 10 H osd_layout 2 113 1 1 H osd_layout 2 114 1 2 H osd_layout 2 115 1 3 H osd_layout 2 116 1 4 H osd_layout 2 117 0 0 H osd_layout 2 118 0 0 H osd_layout 2 119 0 0 H osd_layout 2 120 0 0 H osd_layout 2 121 3 4 H osd_layout 2 122 3 5 H osd_layout 2 123 3 6 H osd_layout 2 124 23 2 H osd_layout 2 125 0 0 H osd_layout 2 126 0 0 H osd_layout 2 127 0 0 H osd_layout 2 128 0 0 H osd_layout 2 129 0 10 H osd_layout 2 130 2 7 H osd_layout 2 131 2 8 H osd_layout 2 132 2 9 H osd_layout 2 133 2 10 H osd_layout 2 134 0 0 H osd_layout 2 135 0 0 H osd_layout 2 136 0 0 H osd_layout 2 137 0 0 H osd_layout 2 138 0 0 H osd_layout 2 139 0 0 H osd_layout 2 140 12 3 H osd_layout 2 141 12 3 H osd_layout 2 142 20 3 H osd_layout 2 143 0 0 H osd_layout 2 144 1 4 H osd_layout 2 145 1 3 H osd_layout 2 146 20 3 H osd_layout 3 0 23 0 H osd_layout 3 1 12 0 H osd_layout 3 2 0 0 H osd_layout 3 3 8 6 H osd_layout 3 4 8 6 H osd_layout 3 5 23 8 H osd_layout 3 6 23 9 H osd_layout 3 7 13 12 H osd_layout 3 8 20 2 H osd_layout 3 9 1 2 H osd_layout 3 10 8 6 H osd_layout 3 11 2 3 H osd_layout 3 12 1 4 H osd_layout 3 13 23 1 H osd_layout 3 14 0 11 H osd_layout 3 15 1 0 H osd_layout 3 16 2 10 H osd_layout 3 17 2 11 H osd_layout 3 18 2 12 H osd_layout 3 19 15 1 H osd_layout 3 20 18 12 H osd_layout 3 21 0 12 H osd_layout 3 22 14 11 H osd_layout 3 23 1 1 H osd_layout 3 24 12 2 H osd_layout 3 25 23 5 H osd_layout 3 26 24 7 H osd_layout 3 27 3 5 H osd_layout 3 28 23 11 H osd_layout 3 29 23 12 H osd_layout 3 30 1 13 H osd_layout 3 31 0 10 H osd_layout 3 32 12 1 H osd_layout 3 33 6 2 H osd_layout 3 34 18 2 H osd_layout 3 35 1 5 H osd_layout 3 36 1 5 H osd_layout 3 37 1 6 H osd_layout 3 38 1 7 H osd_layout 3 39 1 5 H osd_layout 3 40 1 2 H osd_layout 3 41 1 8 H osd_layout 3 42 1 7 H osd_layout 3 43 0 0 H osd_layout 3 44 0 0 H osd_layout 3 45 0 0 H osd_layout 3 46 3 6 H osd_layout 3 47 3 7 H osd_layout 3 48 23 7 H osd_layout 3 49 23 6 H osd_layout 3 50 0 0 H osd_layout 3 51 12 2 H osd_lay

[krugs44364]

No luck.

On Fri, Feb 2, 2024 at 4:05 PM Sensei @.***> wrote:

Here's something you can try, BTW:

Turn SoftSerial back on. Save and reboot. I think you will see smartport telemetry will be enabled on Softserial by default. Remove smartport from softserial. Save and reboot. Disable softserial.

Discover new telemetry sensors.

It's possible that the default config is trying to send telemetry to a port that does not exist.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1922832405, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC55G35BQVCXDU5WDMNDYRRXZ5AVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRSHAZTENBQGU . You are receiving this because you authored the thread.Message ID: @.***>

-- Kind regards, Carel Kruger

[kd8b]

All Telemetry working correctly for me. Matek-F405-WING-V2 -Matek M10q-5883, GPS-Compass, BetaFPV, SuperD RX2400 ELRS. I just set up a Matek f405 wing v2 on a vtail plane with 7.0.0. I too saw the issue with no elrs telemetry from the controller. I did find in my case, that the soft serial was in fact set to smartport by default and disabled it. Problem corrected. 24 items of telemetry after re-running discover new. Telemetry Output enabled in config. ELRS running 12 ch mixed mode. Crossfire enabled in yaapu config in my case as I run INAV Telemetry widget as well. RX on UART2 GPS on UART3. It can work,

[krugs44364]

Hi kd8b, Thanks for that. Would you be prepared to share your INAV dump file with me?

[krugs44364]

Hi kd8b, That is good to hear (i think). Would you share your INAV dump file with me?

On Mon, Feb 5, 2024 at 9:38 AM kd8b @.***> wrote:

All Telemetry working correctly for me. Matek-F405-WING-V2 -Matek M10q-5883, GPS-Compass, BetaFPV, SuperD RX2400 ELRS. I just set up a Matek f405 wing v2 on a vtail plane with 7.0.0. I too saw the issue with no elrs telemetry from the controller. I did find in my case, that the soft serial was in fact set to smartport by default and disabled it. Problem corrected. 24 items of telemetry after re-running discover new. Telemetry Output enabled in config. ELRS running 12 ch mixed mode. Crossfire enabled in yaapu config in my case as I run INAV Telemetry widget as well. RX on UART2 GPS on UART3. It can work,

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1925950023, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC56J5BA7BGIMSWJO3X3YSAEVFAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRVHE2TAMBSGM . You are receiving this because you authored the thread.Message ID: @.***>

-- Kind regards, Carel Kruger

[kd8b]

Dump - Talon GT Rebel-Matek F405 Wing - v2 - INAV_7.0.0_cli_20240204_183924.txt.zip I hope this is the correct way to do this as I have never uploaded to Github before.

[krugs44364]

Thanks got it.

On Mon, Feb 5, 2024 at 10:50 AM kd8b @.***> wrote:

Dump - Talon GT Rebel-Matek F405 Wing - v2 - INAV_7.0.0_cli_20240204_183924.txt.zip https://github.com/iNavFlight/inav/files/14158994/Dump.-.Talon.GT.Rebel-Matek.F405.Wing.-.v2.-.INAV_7.0.0_cli_20240204_183924.txt.zip I hope this is the correct way to do this as I have never uploaded to Github before.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1925991364, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC57GM74UK5FXY3TOKDTYSANFLAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRVHE4TCMZWGQ . You are receiving this because you authored the thread.Message ID: @.***>

-- Kind regards, Carel Kruger

[kd8b]

My INAV build is untested in flight so consider this a test bench setup until verified. New to INAV Airplane but have multiple INAV quad builds

[krugs44364]

Thanks, at this point mine is also just test bench until I can get the telemetry to work.

On Mon, Feb 5, 2024 at 10:52 AM kd8b @.***> wrote:

My INAV build is untested in flight so consider this a test bench setup until verified. New to INAV Airplane but have multiple INAV quad builds

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1925992901, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC5364DEFEQAFVOYEE6DYSANMDAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMRVHE4TEOJQGE . You are receiving this because you authored the thread.Message ID: @.***>

-- Kind regards, Carel Kruger

[krugs44364]

Well, that didn't work either. For now, I will just have to run with Ardupilot on the F405-wingV2.

[MrD-RC]

If you are getting control but no telemetry, it’s 1 of 2 things usually.

1. The RX and TX are the wrong way around.
2. The receiver configuration is wrong. Check in the Crossfire LUA to make sure those pads are set to CRSF TX and CRSF RX.

[krugs44364]

I've ruled those out already. My receiver is on a duPont 4 pin connector, so I just move it to a F405-WMN and the telemetry works. So the radio, Lua, receiver, wiring etc. is common only change is the FC and obviously the firmware. Using the same hardware, when I flash Arduplane on to the F405-wingV2 the telemstry also works albeit with Yaapu on my TX16s instead of the Inav Lua.

[MrD-RC]

Then it must be a setting on the receiver page. CRSF works just fine. It can only be setup if you’ve proven all the hardware.

[krugs44364]

Hi Darren, Yes, I agree it just works - normally. I’ve done lots of setups without issues.

This is what my receiver tab looks like. [image: image.png] I've also tried changing the Serial receiver half duplex setting to off and still nothing. The way this is set is identical to how it is on my F405-WMN where telemetry works.

This has got me stumped and quite frustrated.

Kind regards, Carel Kruger

On Wed, 7 Feb 2024 at 10:06 am, Darren Lines @.***> wrote:

Then it must be a setting on the receiver page. CRSF works just fine. It can only be setup if you’ve proven all the hardware.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-1930918443, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC54DRINHMZOPI3Z3HGLYSKZOBAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMYTSMZQHEYTQNBUGM . You are receiving this because you authored the thread.Message ID: @.***>

[krugs44364]

I finally resolved the issue by updating the TX module firmware to the latest available. Still a bit of a puzzle why the older firmware would work on some older FC's but not on a new Matek F405-wingV2.

[b14ckyy]

@krugs44364 can you please do me a favor and check if it still works with INAV 7.1 RC1 or this inifficial RC2 I made? https://1drv.ms/f/s!Ar6QsGgoXRgqyPk8iOYA_eGtgz0T-w?e=A4mIfl

do a fresh telemetry sensor scan and check if you see a Vspd sensor in that list.

[krugs44364]

Ok, I'll check.

On Thu, Mar 21, 2024 at 8:37 AM b14ckyy @.***> wrote:

@krugs44364 https://github.com/krugs44364 can you please do me a favor and check if it still works with INAV 7.1 RC1 or this inifficial RC2 I made? https://1drv.ms/f/s!Ar6QsGgoXRgqyPk8iOYA_eGtgz0T-w?e=A4mIfl https://1drv.ms/f/s!Ar6QsGgoXRgqyPk8iOYA_eGtgz0T-w?e=A4mIfl&fbclid=IwAR1Xl_HEmQKRJMXpcgoZrq-1eS4M6BPGAywUds-Ca4UUZYCdqI2Gkm7kr2E

do a fresh telemetry sensor scan and check if you see a Vspd sensor in that list.

— Reply to this email directly, view it on GitHub https://github.com/iNavFlight/inav/issues/9685#issuecomment-2010683259, or unsubscribe https://github.com/notifications/unsubscribe-auth/AHKTC57T5ASKELYKBMYLXJTYZH6QPAVCNFSM6AAAAABCVYHYRWVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDAMJQGY4DGMRVHE . You are receiving this because you were mentioned.Message ID: @.***>

-- Kind regards, Carel Kruger

[krugs44364]

Hi, It work on both 7.1RC1 and RC2 and I can see Vspd.

[b14ckyy]

awesome thanks. I will close here then.