Closed Fabrizio69 closed 4 years ago
Item | IIT Code | Description | Qty | Link | Done |
---|---|---|---|---|---|
1 | 14701 | Adafruit DRV8871 Brushed DC Motor Driver Breakout | 25 | mouser | X |
2 | Honeywell HAF 50 lpm flowmeter | 4 | mouser | X | |
3 | Honeywell AWM3300V analog flowmeter |
4 | Mouser | X | |
4 | Pressure sensor I2C 100mbar ABPDLNN100MG2A3 |
5 | Mouser | X | |
5 | Prototype circuit board for general purpose | 5 | Mouser | X | |
6 | Prototype circuit board 2 sides | 5 | Mouser | X | |
7 | 14703 | Dev kit STM32F746G-DISCO |
2 | mouser | X |
8 | Pressure sensor ABPDANN005PG2A3 I2C |
5 | mouser | Delivery T: 12 weeks, replaced by item 28 | |
9 | General purpose low power MOSFET 2N7000 |
20 | Mouser | X | |
10 | General purpose BJT 2SC1815 |
20 | Mouser | X | |
11 | General purpose diode 1N4148 |
20 | Mouser | X | |
12 | Piezo buzzer CPE-827 |
10 | Mouser | X | |
13 | Piezo buzzer TDK PS1440P02BT |
10 | Mouser | X | |
14 | 14702 | Adafruit Breadboard Friendly Buzzer 5V | 10 | Mouser | X |
15 | Harwin header pin strip 40pin, 2.54mm pitch | 10 | Mouser | X | |
16 | Harwin receptacle 32pin, 2.54mm pitch | 10 | Mouser | X | |
17 | Omron G2RL-1-HA DC12 general purpose relay SPDT |
5 | Mouser | X | |
18 | Omron G2RL-24-DC12 general purpose relay DPDT |
5 | Mouser | X | |
19 | Molex 39773-0002 2pin 2.54mm pitch fixed terminal block |
20 | Mouser | X | |
20 | Molex 39773-0004 4pin 2.54mm pitch fixed terminal block |
20 | Mouser | X | |
21 | 14725 | LED Panel RED | 10 | Mouser | X |
22 | 14724 | LED Panel GREEN | 10 | Mouser | X |
23 | 14726 | LED Panel YELLOW | 10 | Mouser | X |
24 | Jumper Harwin M7686-46 2 position 2.54mm black | 20 | Mouser | X | |
25 | Jumper Harwin M7687-05 2 position 2.54mm blue | 20 | Mouser | X | |
26 | Jumper Harwin M7685-46 2 position 2.54mm red | 20 | Mouser | X | |
27 | Jumper Kobiconn 151-8010-E 2 position 2.54mm black | 20 | Mouser | X | |
28 | Honeywell HSCMAND160MD2A5 160mbar I2C pressure sensor |
5 | Mouser | X |
@Fabrizio69 io metterei dentro anche i sensori di pressione e altri componenti. Cosa ne dite?
cc: @claudiolorini @MrAndrea @simeonedussoni
Si metterei diversi sensori di pressione e di flusso disponibili su Mouser in modo da far un ordine unico. Bisognerà pensare anche all'acquisto di tubi e raccordi adatti.
demo board added to the list
Di flowmeter ce ne sono di due versioni. Chiedo al meccanico cosa preferisce se 3/8 o tubo da 22mm a innesto.
We should create a basket once the list is completed. It is easier to handle for Purchasing office.
@Fabrizio69 sorry but we want to replace the demo board with this one:
i have updated the list
@maggia80 @MrAndrea the delivery time for the item 8 (see https://github.com/icub-tech-iit/ventilator/issues/26#issuecomment-608475043) is critical. Do you have an alternative code?
@Fabrizio69 this can be a viable alternative: 160mbar I2C pressure sensor cc @maggia80 @MrAndrea
@simeonedussoni replaced the the code in the order (see the table). Purchase done.
cc: @maggia80 @MrAndrea
chiudiamo questa issue? ne apro un altra?
... continue with this issue in another table
2nd ROUND OF ORDERS
Item | IIT Code | Description | Qty | Link | Done |
---|---|---|---|---|---|
1 | 14699 | TCA9548A I2C Multiplexer | 5 | mouser | X |
2 | 14700 | MCP23017 GPIO Expander | 5 | mouser | X |
3 | Adafruit ADS1015 Breakout 12-Bit ADC, I2C | 5 | Mouser | X | |
4 | Adafruit ADS1115 16-Bit ADC - 4 Channel with Programmable Gain Amplifier, I2C | 5 | Mouser | X | |
5 | Flowmeter 3/8 inch HAFUHT0050L4AXT | 4 | mouser | X | |
6 | 14697 | Honeywell HSCDANN150PG2A5 I2C, 12 bit, 150PSI (~10bar), barbed |
5 | Mouser | X |
7 | Honeywell HSCSANN100PA2A5 I2C, 12 bit, 100PSI (~7bar), barbed |
5 | Mouser | X | |
8 | Honeywell HSCDANN010BGAA5 analog output, 10bar, barbed |
5 | Mouser | X |
added the flowmeter with the different interface.
@MrAndrea we need to add a pressure sensor with 0-5bar or 0-10 bar pressure range.
all the sensors should be barbed
I found the following available on Mouser and I add them to the above comment:
Honeywell HSCDANN150PG2A5 I2C, 12 bit, 150PSI (~10bar), barbed
Honeywell HSCSANN100PA2A5 I2C, 12 bit, 100PSI (~7bar), barbed
Honeywell HSCDANN010BGAA5 analog output, 10bar, barbed
Note: there are other models (HSCDANN150PG7A5, HSCSANN150PA2A5) but not available on Mouser.
2nd round of orders (see https://github.com/icub-tech-iit/ventilator/issues/26#issuecomment-609788678) DONE.
3rd ROUND OF ORDERS
Item | IIT Code | Description | Qty | Link | Done |
---|---|---|---|---|---|
1 | 6420 | Connettore USB da pannello tipo A | 5 | farnell | X |
2 | 14698 | Honeywell HSCMAND160MD2A5 I2C, 12 bit, 160mbar, barbed |
5 | Mouser | X |
3 | EnviteC OOM109 oxygen sensor |
2 | Dealer: AMS, contact: enrica.badocchi@amstrento.it |
X | |
4 | 5123 | External power supply for medical use | 2 | X | |
5 | 5133 | Panel connector, circular, 4 contacts, female, shielded, Straight, w to panel | 2 | X | |
6 | 6808 | Plastic fuseholder, for 5x20mm fuse, IP67 | 5 | X | |
7 | 7045 | Rocker switch DPST, off-on switch configuration | 2 | X | |
8 | 10792 | Not insulated, DC/DC Converter, Vin 18/36V, Vout 5V, 6A, 30W, insulation 1.5kVdc, THD, DIP | 2 | X | |
9 | 4738 | Not insulated, DC/DC Converter, Vin 4.75/36V, Vout 3.3V, 1A, THD, SIP | 2 | X | |
10 | Tastiera a membrana 4 x 1 a 4 tasti | 2 | RS | X | |
11 | Tastiera a membrana 4 x 3 a 12 tasti | 2 | RS | X | |
12 | Adafruit Membrane 1x4 Keypad | 2 | Mouser | X | |
13 | Adafruit Membrane 3x4 Matrix Keypad | 2 | Mouser | X | |
14 | Codificatori 12PPR 24Detents 5V 2bit GrayCodeKnurled | 4 | Mouser | X | |
15 | Codificatori 12PPR 12Detents 5V 2bit GrayCodeKnurled | 4 | Mouser | X | |
16 | Codificatori ENCODER 9MM 20MM SHAFT, PUSH SWITCH | 2 | Mouser | X | |
17 | Potenziometro Vishay, 10kΩ, Rotante, 3 giri, Ø albero 6,35 mm | 4 | RS | X | |
18 | Potenziometro Vishay, 5kΩ, Rotante, 5 giri, Ø albero 6,35 mm | 4 | RS | X | |
19 | Led e portale 5V verde | 5 | RS | X | |
20 | Led e portale 5V rosso | 5 | RS | X | |
21 | Led e portale 12V rosso | 5 | RS | X | |
22 | Led e portale 12V verde | 5 | RS | X | |
23 | Interruttore a bilanciere Arcolectric, C1350ALAAF, DPST (Double Pole Single Throw), On-Off, corrente nominale 16 A a | 3 | RS | X | |
24 | Pulsante di arresto di emergenza M22-L-W+M22-A+M22-LED230-W, foro 22.5mm, Montaggio a filo, posteriore, montaggio | 2 | RS | X | |
25 | Pulsante di emergenza A fungo Schneider Electric, Ø testa 30mm, Ruotare per ripristinare, Rosso, IP66, IP69, IP69K | 2 | RS | X | |
26 | Blocco contatti luminoso Schneider Electric, 1NC, 600 V, terminali a Vite | 2 | RS | X | |
27 | Manopola per potenziometro RS PRO Grano, Ø 22mm x 14mm, albero da 6.35mm, Nero | 5 | RS | X | |
28 | Manopola per potenziometro RS PRO Grano, Ø 28mm x 14mm, albero da 6.35mm, Argento | 5 | RS | X | |
29 | Manopola per potenziometro RS PRO Grano, Ø 16mm x 14mm, albero da 6.35mm, Nero | 5 | RS | X |
@MrAndrea @claudiolorini if the component is normalized in the WinGST database, the IIT code can be used so that it can be managed in the warehouse. I add the IIT Code column to the table above
the HSC series have a different mechanical interface wrt the ABP.
@maggia80 , @MrAndrea I've prepared the AMS purchase issue for our administration. Can I proceed with the order?
Item | IIT Code | Description | Qty | Link | Done |
---|---|---|---|---|---|
3 | EnviteC OOM109 oxygen sensor |
2 | Dealer: AMS, contact: enrica.badocchi@amstrento.it |
X |
For better reference on the Envitec oxygen sensor look at this comment.
Yes @Fabrizio69, as discussed in the meeting this morning with @maggia80.
@maggia80 , @MrAndrea I've prepared the AMS purchase issue for our administration. Can I proceed with the order?
Item IIT Code Description Qty Link Done 3 EnviteC
OOM109
oxygen sensor 2 Dealer: AMS, contact: enrica.badocchi@amstrento.it
Administration is already preparing the order.=
The purchases (see 3rd ROUND OF ORDERS) are ready to go. Give me a GO!!! to send the requests
@MrAndrea @claudiolorini @randaz81
@Fabrizio69 I added the components discussed with @randaz81. Add them in the RDA and GO thanks!
@MrAndrea the q.ty for the missing knobs (see issue https://github.com/icub-tech-iit/ventilator/issues/27#issuecomment-611916479)?
@MrAndrea the q.ty for the missing knobs (see issue #27 (comment))?
@Fabrizio69 I think 5 of each should be enough.
Added knobs in the table (see item 27, 28, 29) according to the issue https://github.com/icub-tech-iit/ventilator/issues/27#issuecomment-611916479.
3rd round of orders (see https://github.com/icub-tech-iit/ventilator/issues/26#issuecomment-610241499) DONE.
For the item 13 - Mouser the delivery time is more than 12 weeks. See...
cc: @MrAndrea @maggia80
This purchase is completed (delivered).
let me close it. All the orders have been submitted
Collection of BOMs or components for purchases