Closed MrAndrea closed 1 year ago
This comment collects the boards used in the ventilator. Each board needs a Capital symbol.
This comment collects the components used in the ventilator. Each component needs a Capital symbol.
@MrAndrea please consider that depending on @claudiolorini choices we may use the adafruit connectors or not.
CN1 | dc power input | Mouser | Kycon | PJX-PM-4S | Panel connector, circular, 4 contacts, female, shielded, Straight, w to panel, 7.5A |
---|---|---|---|---|---|
PS1 | Power supply | IIT | Xp power | AHM100PS12 | External power supply for medical use, 100W, 80 → 264Vca, output 12V 8.33A |
CN2-CN3 | Usb panel | Farnell | Multicomp | 1850634 | Connettore USB da pannello tipo A |
FS1 | fuse | RS Components | Schurter | 3101.013 | Plastic fuseholder, for 5x20mm fuse, IP67 |
SW1 | switch | RS Components | Arcoletric | C1350ALGAC | Rocker switch DPST, off-on switch configuration, flat plug connection 30x22mm, for panel |
KNOB1-KNOB4 | potentiometer | RS Components | Vishay | 533B1103JL | Potenziometro Vishay, 10kΩ, Rotante, 3 giri, Ø albero 6,35 mm |
BAT1 | battery | Mouser | Conrad Energy | 250915 | energy 12 V 9 Ah 250915 Batteria al piombo 12 V 9 Ah Piombo-AGM (L x A x P) 151 x 94 x 65 mm Spina piatta 6,35 mm |
LED1 | led | Mouser | Byvar | MPR3HD | LED Panel RED |
LED2 | led | Mouser | Byvar | MPR3GD | LED Panel GREEN |
LED3-LED6 | led | Mouser | Byvar | MPR3YD | LED Panel YELLOW |
BTN1 | 4 buttons | RS Components | Apem | AC3559 | Tastiera a membrana 4 x 1 a 4 tasti |
FLT1 | FLT button | Schneider Electric | ZB4BS834 | Fault button | |
MENU1 | selector | Mouser | Bourns | PEC09-2320F-T0015 | Codificatori ENCODER 9MM 20MM SHAFT, PUSH SWITCH |
maybe S7 (analog) is easier to connect to CTR1.
una nota: i led sui tastix4 vengono coperti dalla mano quando premi. Meglio sopra.
una nota: i led sui tastix4 vengono coperti dalla mano quando premi. Meglio sopra.
si Claudio ho fatto la stessa osservazione ieri e li spostano
I have updated the picture above. adding S3 that was missing
Here the first draft of the logic and harness schematics of the ventilator.
@MrAndrea for the Harness and Logic BOMs?
Here the rev. 0.0.1 of the logic and harness schematics of the ventilator.
IITvsC19 Ventilator Logic_Diagram_0.0.1.pdf
IITvsC19 Ventilator Harness_Diagram_0.0.1.pdf
The BOMs are on Wingst with this code:
Next revision will have information about accurate cables length and other stuff useful for a good (cable ties, bundles insulation, labels, etc.). The cables length in the 0.0.1 are estimated since we are waiting this information from the mechanical cad.
we should add some cable tie for grounding (RS Link)
I added 2 wires awg17 green/yellow with 2 terminal rings
Revision 0.0.2 released to Ferrari.
From my email to Ferrari:
Rispetto alla precedente ci sono alcune piccole correzioni/aggiunte:
- sul logic i cavi di sezione awg14 sono stati sostituiti con awg20, sono stati aggiunti 2 cavi per la terra, un connettore corretto (quello per l’encoder CTR1S_J11), CN3 collegato a USB_CN14
- sull’harness sono stati sincronizzati i cambiamenti del logic e aggiunti altri componenti per identificare meglio i cavi (label, fascette)
Revision 0.0.3 released to Ferrari.
From my email to Ferrari:
Ci sono alcune correzioni rispetto alla versione precedente che rispecchiano il cablaggio che è stato effettuato sul ventilatore (aggiunta di alcuni connettori per sezionare dei cavi, di un cavo di terra, di un driver per pilotare la valvola on/off e relativi cavi). Sullo schema harness sono stati sincronizzati i cambiamenti del logic e aggiunti altri componenti (termorestringenti, label, fascette), indicando per tutti i bundle le lunghezze reali. Nel complesso comunque questa revisione rispetta già quello che è rappresentato nel cad meccanico ed il primo prototipo costruito; ora dobbiamo rifinire le ultime cose, ma nella prossima revisione non ci saranno grosse differenze.
I think we can close this issue.
This issue to create and describe the electrical schematic of the ventilator using Mentor Capital.