combs
commented
3 years ago same with an older A13 device--I see output like this:
./felix -v --info
FELix 1.0 RC6 by Lolet
Warning: I don't give any warranty on this software. You use it at own risk!
────────────────────────────────────
* Connecting to device at port 2, FEL device 1@57 1f3a:efe8 [OK]
--> ( 32) USBWrite (Prepare for write of 16 bytes)
--> ( 16) FESInfo (0x203): 03 02 00 00 00 00 00 00 00 00 00 00 00 00 00 00
<-- ( 13) AWUSBResponse 0x0, status ok
--> ( 32) USBRead (Prepare for read of 32 bytes)
<-- ( 13) AWUSBResponse 0x0, status ok
<-- ( 8) FELStatusResponse mark 65535, tag 0, state 1
[FATAL]
Failed to get the data (
An unexpected answer length (13 <> 32))
* Cleaning up [OK]
./felix -v --read boot.img --item boot
FELix 1.0 RC6 by Lolet
Warning: I don't give any warranty on this software. You use it at own risk!
────────────────────────────────────
* Connecting to device at port 2, FEL device 1@57 1f3a:efe8 [OK]
--> ( 32) USBWrite (Prepare for write of 16 bytes)
--> ( 16) FESUpload (0x207): 07 02 00 00 00 00 00 00 00 40 00 00 00 00 00 00
<-- ( 13) AWUSBResponse 0x0, status ok
--> ( 32) USBRead (Prepare for read of 16384 bytes)
<-- ( 13) AWUSBResponse 0x0, status ok
<-- ( 8) FELStatusResponse mark 65535, tag 0, state 1
[FATAL]
Failed to get the data (
An unexpected answer length (13 <> 16384))
* Cleaning up [OK]
the --status flag works and outputs this:
./felix --status
FELix 1.0 RC6 by Lolet
Warning: I don't give any warranty on this software. You use it at own risk!
────────────────────────────────────
* Connecting to device at port 2, FEL device 1@57 1f3a:efe8 [OK]
magic AWUSBFEX
board Allwinner A13/A10s (sun5i), revision 0
fw 1
mode fel
data_flag 0x00000044
data_length 0x00000008
data_start_address 0x00007e00
reserved [0, 0, 0, 0, 0, 0, 0, 0]
* Cleaning up [OK]it is possible to dump memory by address and length--I spose I'll just figure out the addresses and dump it that way in my case...
./felix --read test.img --address 0 --length 65536
FELix 1.0 RC6 by Lolet
Warning: I don't give any warranty on this software. You use it at own risk!
────────────────────────────────────
* Connecting to device at port 2, FEL device 1@57 1f3a:efe8 [OK]
* fel: Reading data (65536/65536 bytes) [OK]
* Cleaning up [OK]
Hello. I've go an x64 WIndows machine on which I managed to execute felix,, but it still gives me touble. this is what I get if I for example ask for info: ruby felix --info FELix 1.0 RC6 by Lolet Warning: I don't give any warranty on this software. You use it at own risk! ────────────────────────────────────
I have a XIaomi MiReader with an Allwinner B300 chipset.