Open GoogleCodeExporter opened 9 years ago
I put the original FW back in the router, then Padavan.
Then the modem worked in Padavan again, but only for once.
As soon as the modem was removed and connected again, it does not be found...
Please help!
Original comment by yeppey...@gmail.com
on 8 Nov 2013 at 10:40
> usb_modeswitch: switching device 12d1:14fe on 001/009
and hush...
Some Huawei modems not switched via usb_modeswitch from first tryes. While
usb_modeswitch not switched, modem visible as CD-ROM.
Use AT^SETPORT cmd for disable autostart CD-ROM.
Original comment by andy.pad...@gmail.com
on 9 Nov 2013 at 2:40
You who got the knowledge in the opposite to me, do you know the AT command for
Huawei E3276-150, to disable CD-ROM autostart?
The info I can give you is:
-------------------------------------------
AT^SETPORT?
^SETPORT:A1,A2;12,16,A1,A2
-------------------------------------------
AT^SETPORT=?
^SETPORT:1: 3G MODEM
^SETPORT:2: 3G PCUI
^SETPORT:3: 3G DIAG
^SETPORT:5: 3G GPS
^SETPORT:A: BLUE TOOTH
^SETPORT:16: NCM
^SETPORT:A1: CDROM
^SETPORT:A2: SD
^SETPORT:10: 4G MODEM
^SETPORT:12: 4G PCUI
^SETPORT:13: 4G DIAG
^SETPORT:14: 4G GPS
-------------------------------------------
Thank you!
Original comment by yeppey...@gmail.com
on 10 Nov 2013 at 1:20
I seem to have the latter problem, e.g. modeswitchrule is working but still no
internet connection.
modem: e3276s-210 (hi-link, latest firmware)
country: Sweden
Jan 1 00:01:37 kernel: usb 1-2: new high speed USB device number 2 using
xhci_hcd
Jan 1 00:01:37 kernel: usb 1-2: New USB device found, idVendor=12d1,
idProduct=1f01
Jan 1 00:01:37 kernel: usb 1-2: New USB device strings: Mfr=2, Product=1,
SerialNumber=0
Jan 1 00:01:37 kernel: usb 1-2: Product: HUAWEI Mobile
Jan 1 00:01:37 kernel: usb 1-2: Manufacturer: HUAWEI Technology
Jan 1 00:01:37 kernel: scsi0 : usb-storage 1-2:1.0
Jan 1 00:01:40 kernel: scsi 0:0:0:0: CD-ROM HUAWEI Mass Storage
2.31 PQ: 0 ANSI: 2
Jan 1 00:01:40 kernel: scsi 0:0:0:0: Attached scsi generic sg0 type 5
Jan 1 00:01:40 usb_modeswitch: switching device 12d1:1f01 on 001/002
Jan 1 00:01:40 kernel: usb 1-2: USB disconnect, device number 2
Jan 1 00:01:41 kernel: usb 1-2: new high speed USB device number 3 using
xhci_hcd
Jan 1 00:01:41 kernel: usb 1-2: New USB device found, idVendor=12d1,
idProduct=14db
Jan 1 00:01:41 kernel: usb 1-2: New USB device strings: Mfr=2, Product=1,
SerialNumber=0
Jan 1 00:01:41 kernel: usb 1-2: Product: HUAWEI Mobile
Jan 1 00:01:41 kernel: usb 1-2: Manufacturer: HUAWEI Technology
Jan 1 00:01:41 kernel: cdc_ether 1-2:1.0: weth0: register 'cdc_ether' at
usb-0000:01:00.0-2, CDC Ethernet Device, 58:2c:80:13:92:63
Jan 1 00:01:46 usb modem hotplug: try autorun modem wan connection...
Jan 1 00:01:46 stop_wan(): raise DHCP release event
Jan 1 00:01:47 RT-N65U: Hardware NAT/Routing: Enabled, IPoE/PPPoE offload
[WAN]<->[LAN/WLAN]
Jan 1 00:01:47 RT-N65U: Hardware NAT/Routing: IPv4 UDP flow offload - OFF
Jan 1 00:01:47 RT-N65U: Hardware NAT/Routing: IPv6 routes offload - OFF
Jan 1 00:01:47 DHCP WAN Client: starting on weth0 ...
Jan 1 00:01:48 RT-N65U: wan up (weth0)
Jan 1 00:01:48 dnsmasq[385]: read /etc/hosts - 3 addresses
Jan 1 00:01:48 dnsmasq[385]: read /etc/storage/dnsmasq/hosts - 0 addresses
Jan 1 00:01:48 DHCP WAN Client: bound (weth0), IP: 192.168.1.100, GW:
192.168.1.1, lease time: 86400
Could somebody confirm my suspicion, or educate me otherwise.
Also, if the solution is to turn of cd-rom mode , how do I send the at
commands? I can't seem to understand how to do it buy just googleing.
Thank you!!!
Original comment by erhardte...@gmail.com
on 12 Nov 2013 at 12:54
Original issue reported on code.google.com by
yeppey...@gmail.com
on 7 Nov 2013 at 5:12