cld2 testsuite failures

[GoogleCodeExporter]

What steps will reproduce the problem?
1. checkout revision 194
2. use the cmake file (probably doesn't change anything)
3. use ubuntu 14.10 x64

build it and run tests
make[1]: Entering directory '/tmp/buildd/cld2-0.0.0~svn194'
cd obj-* && echo "this is some english text" | ./compact_lang_det_test_chrome_2
ExtLanguage ENGLISH(96% 1851p), 27/26 bytes of non-tag letters, Summary: ENGLISH
  SummaryLanguage ENGLISH at 0 of 26 81us (0 MB/sec), (null)
cd obj-* && echo "this is some english text" | ./compact_lang_det_test_chrome_16
ExtLanguage ENGLISH(96% 1851p), 27/26 bytes of non-tag letters, Summary: ENGLISH
  SummaryLanguage ENGLISH at 0 of 26 79us (0 MB/sec), (null)
cd obj-* && ./cld2_unittest_chrome_2 > /dev/null
*** Bad UTF-8 after 40 bytes<br>
Checking that non-dynamic implementations of dynamic data methods are no-ops 
(ignore the warnings).
WARNING: Dynamic mode not active, loadDataFromFile has no effect!
WARNING: Dynamic mode not active, loadDataFromRawAddress has no effect!
WARNING: Dynamic mode not active, unloadData has no effect!
Done checking non-dynamic implementations of dynamic data methods, care about 
warnings again.
PASS
cd obj-* && ./cld2_unittest_avoid_chrome_2 > /dev/null
*** Bad UTF-8 after 40 bytes<br>
Checking that non-dynamic implementations of dynamic data methods are no-ops 
(ignore the warnings).
WARNING: Dynamic mode not active, loadDataFromFile has no effect!
WARNING: Dynamic mode not active, loadDataFromRawAddress has no effect!
WARNING: Dynamic mode not active, unloadData has no effect!
Done checking non-dynamic implementations of dynamic data methods, care about 
warnings again.
PASS
cd obj-* && echo "this is some english text" | ./compact_lang_det_test_full
ExtLanguage ENGLISH(96% 1772p), 27/26 bytes of non-tag letters, Summary: ENGLISH
  SummaryLanguage ENGLISH at 0 of 26 153us (0 MB/sec), (null)
cd obj-* && ./cld2_unittest_full > /dev/null
PASS
cd obj-* && ./cld2_unittest_full_avoid > /dev/null
PASS
cd obj-* && ./cld2_dynamic_data_tool --dump cld2_data.bin
cd obj-* && ./cld2_dynamic_data_tool --verify cld2_data.bin
cd obj-* && echo "this is some english text" | 
./compact_lang_det_dynamic_test_chrome --data-file cld2_data.bin
Loading data from: cld2_data.bin
Data loaded, test commencing
ExtLanguage ENGLISH(96% 1851p), 27/26 bytes of non-tag letters, Summary: ENGLISH
  SummaryLanguage ENGLISH at 0 of 26 69us (0 MB/sec), --data-file
cd obj-* && ./cld2_dynamic_unittest --data-file cld2_data.bin > /dev/null
*** Bad UTF-8 after 40 bytes<br>
*** Bad UTF-8 after 40 bytes<br>
PASS
make[1]: Leaving directory '/tmp/buildd/cld2-0.0.0~svn194'

don't know, is everything ok?

Original issue reported on code.google.com by costamag...@gmail.com on 12 Feb 2015 at 5:24

[GoogleCodeExporter]

I'm unclear what failure you are referring to. the Bad UTF-8 messages are 
deliberate -- they are part of the unit test for detection of bad UTF-8. Hence 
the unit test subsequently prints "PASS". If bad UTF-8 were NOT detected, the 
unit test would fail. /dick

Original comment by dsi...@google.com on 12 Feb 2015 at 6:07

• Changed state: WontFix

[GoogleCodeExporter]

wonderful, thanks!

I was expecting this answer, but I asked because the Warnings and UTF8 were a 
little "worrying".

Anyway thanks, it is working correctly then!

Original comment by costamag...@gmail.com on 12 Feb 2015 at 6:13

[GoogleCodeExporter]

I'd like to clean this up at some point, so that the warnings aren't output 
under test.

Original comment by andrewha...@google.com on 13 Feb 2015 at 9:29