JohnOH
commented
11 years ago Might tweaks be required in the RF12.cpp code? // pins used for the RFM12B interface - yes, there is logic in this madness: // // - leave RFM_IRQ set to the pin which corresponds with INT0, because the // current driver code will use attachInterrupt() to hook into that // - (new) you can now change RFM_IRQ, if you also enable PINCHG_IRQ - this // will switch to pin change interrupts instead of attach/detachInterrupt() // - use SS_DDR, SS_PORT, and SS_BIT to define the pin you will be using as // select pin for the RFM12B (you're free to set them to anything you like) // - please leave SPI_SS, SPI_MOSI, SPI_MISO, and SPI_SCK as is, i.e. pointing // to the hardware-supported SPI pins on the ATmega, including SPI_SS !
if defined(AVR_ATmega2560) || defined(AVR_ATmega1280)
define RFM_IRQ 2
define SS_DDR DDRB
define SS_PORT PORTB
define SS_BIT 0
define SPI_SS 53 // PB0, pin 19
define SPI_MOSI 51 // PB2, pin 21
define SPI_MISO 50 // PB3, pin 22
define SPI_SCK 52 // PB1, pin 20
elif defined(AVR_ATmega644P)
define RFM_IRQ 10
define SS_DDR DDRB
define SS_PORT PORTB
define SS_BIT 4
define SPI_SS 4
define SPI_MOSI 5
define SPI_MISO 6
define SPI_SCK 7
elif defined(AVR_ATtiny84) || defined(AVR_ATtiny44)
define RFM_IRQ 2
define SS_DDR DDRB
define SS_PORT PORTB
define SS_BIT 1
define SPI_SS 1 // PB1, pin 3
define SPI_MISO 4 // PA6, pin 7
define SPI_MOSI 5 // PA5, pin 8
define SPI_SCK 6 // PA4, pin 9
elif defined(AVR_ATmega32U4) //Arduino Leonardo
define RFM_IRQ 0 // PD0, INT0, Digital3
define SS_DDR DDRB
define SS_PORT PORTB
define SS_BIT 6 // Dig10, PB6
define SPI_SS 17 // PB0, pin 8, Digital17
define SPI_MISO 14 // PB3, pin 11, Digital14
define SPI_MOSI 16 // PB2, pin 10, Digital16
define SPI_SCK 15 // PB1, pin 9, Digital15
else
// ATmega168, ATmega328, etc.
jcw
taisen
Hi everyone,
I've made a sketch works on attiny84, and i 've tried to upload on a attiny87, no compilation errors (i've included correct pin_arduino.h, tiny core). but the attiny freeze on rf12_config(). Could you tell me if the library is compatible attiny87 ?
Maybe it's could help, the file pin_arduino.h
/* pins_arduino.h - Pin definition functions for Arduino Part of Arduino - http://www.arduino.cc/
Copyright (c) 2007 David A. Mellis
This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
$Id: wiring.h 249 2007-02-03 16:52:51Z mellis $ */
ifndef Pins_Arduino_h
define Pins_Arduino_h
include <avr/pgmspace.h>
define NUM_DIGITAL_PINS 16
define NUM_ANALOG_INPUTS 11
define analogInputToDigitalPin(p) ((p < 8) ? 10 -(p): -1)
define digitalPinHasPWM(p) ((p) == 2 || (p) == 3 || (p) == 4 || (p) == 5)
define SS 10
define MOSI 11
define MISO 12
define SCK 13
static const uint8_t SDA = 4; static const uint8_t SCL = 6;
//Ax constants cannot be used for digitalRead/digitalWrite/analogWrite functions, only analogRead(). static const uint8_t A0 = NUM_DIGITAL_PINS; static const uint8_t A1 = NUM_DIGITAL_PINS+1; static const uint8_t A2 = NUM_DIGITAL_PINS+2; static const uint8_t A3 = NUM_DIGITAL_PINS+3; static const uint8_t A4 = NUM_DIGITAL_PINS+4; static const uint8_t A5 = NUM_DIGITAL_PINS+5; static const uint8_t A6 = NUM_DIGITAL_PINS+6; static const uint8_t A7 = NUM_DIGITAL_PINS+7;
//---------------------------------------------------------- //---------------------------------------------------------- //Core Configuration (used to be in core_build_options.h)
//If Software Serial communications doesn't work, run the TinyTuner sketch provided with the core to give you a calibrated OSCCAL value. //Change the value here with the tuned value. By default this option uses the default value which the compiler will optimise out.
define TUNED_OSCCAL_VALUE OSCCAL
//e.g //#define TUNED_OSCCAL_VALUE 0x57
//Choosing not to initialise saves power and flash. 1 = initialise.
define INITIALIZE_ANALOG_TO_DIGITAL_CONVERTER 1
define INITIALIZE_SECONDARY_TIMERS 0
define TIMER_TO_USE_FOR_MILLIS 0
define HAVE_BOOTLOADER 1
/ Where to put the software serial? (Arduino Digital pin numbers) / //WARNING, if using software, TX is on AIN0, RX is on AIN1. Comparator is favoured to use its interrupt for the RX pin.
define USE_SOFTWARE_SERIAL 0
//Please define the port on which the analog comparator is found.
define ANALOG_COMP_DDR DDRA
define ANALOG_COMP_PORT PORTA
define ANALOG_COMP_PIN PINA
define ANALOG_COMP_AIN0_BIT 6
define ANALOG_COMP_AIN1_BIT 7
/ Analog reference bit masks. / // VCC used as analog reference, disconnected from PA0 (AREF)
define DEFAULT (0)
// External voltage reference at PA0 (AREF) pin, internal reference turned off
define EXTERNAL (1)
// Internal 1.1V voltage reference
define INTERNAL (2)
//---------------------------------------------------------- //---------------------------------------------------------- //---------------------------------------------------------- //----------------------------------------------------------
define digitalPinToPCICR(p) (((p) >= 0 && (p) <= 10) ? (&GIMSK) : ((uint8_t *)NULL))
define digitalPinToPCICRbit(p) (((p) >= 3 && (p) <= 10) ? 4 : 5)
define digitalPinToPCMSK(p) (((p) >= 3 && (p) <= 10) ? (&PCMSK0) : (((p) >= 0 && (p) <= 2) ? (&PCMSK1) : ((uint8_t *)NULL)))
define digitalPinToPCMSKbit(p) (((p) >= 3 && (p) <= 10) ? (10 - (p)) : (p))
ifdef ARDUINO_MAIN
// On the Arduino board, digital pins are also used // for the analog output (software PWM). Analog input // pins are a separate set. //#define SS 10 //#define MOSI 11 //#define MISO 12 //#define SCK 13 // +-\/-+ // RX (D 0) PA0 1| |20 PB0 (D 4) // TX (D 1) PA1 2| |19 PB1 (D 5) // (D 12) PA2 3| |18 PB2 (D 6) // (D 3) PA3 4| |17 PB3 (D 7) // AVCC 5| |16 GND // AGND 6| |15 VCC // INT1 (D 11) PA4 7| |14 PB4 (D 8) // (D 13) PA5 8| |13 PB5 (D 9) // (D 10) PA6 9| |12 PB6 (D 2)* INT0 // (D 14) PA7 10| |11 PB7 (D 15) // +----+ // // * indicates PWM pin.
// these arrays map port names (e.g. port B) to the // appropriate addresses for various functions (e.g. reading // and writing) const uint16_t PROGMEM port_to_mode_PGM[] = { NOT_A_PORT, (uint16_t)&DDRA, (uint16_t)&DDRB, };
const uint16_t PROGMEM port_to_output_PGM[] = { NOT_A_PORT, (uint16_t)&PORTA, (uint16_t)&PORTB, };
const uint16_t PROGMEM port_to_input_PGM[] = { NOT_A_PORT, (uint16_t)&PINA, (uint16_t)&PINB, };
const uint8_t PROGMEM digital_pin_to_portPGM[] = { PA, /* 0 / PA, PB, / 2 / PA, / 3 / PB, / 4 / PB, PB, PB, PB, PB, PA, / 10 / PA, PA, PA, PA, PB, /_ 15 */ };
const uint8_t PROGMEM digital_pin_to_bit_mask_PGM[] = { BV(0), /* 0 / _BV(1), BV(6), / 2 _/ BV(3), / 3 _/ BV(0), / 4 _/ _BV(1), _BV(2), _BV(3), _BV(4), _BV(5), BV(6), / 10 _/ _BV(4), _BV(2), _BV(5), _BV(7), BV(7), / 15 */ };
const uint8_t PROGMEM digital_pin_to_timer_PGM[] = { NOT_ON_TIMER, NOT_ON_TIMER, TIMER1A, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, TIMER1B, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, NOT_ON_TIMER, };
endif
endif
//Old code, just here for temporary backup until I decide it is not needed. //WARNING, if using software, RX must be on a pin which has a Pin change interrupt <= 7 (e.g. PCINT6, or PCINT1, but not PCINT8) /*#define USE_SOFTWARE_SERIAL 1 //These are set to match Optiboot pins.
define SOFTWARE_SERIAL_PORT PORTB
define SOFTWARE_SERIAL_TX 0
define SOFTWARE_SERIAL_PIN PINB
define SOFTWARE_SERIAL_RX 1*/
Thanks for your help