A64 olimex: copy SD to eMMC

Hello

I have installed the latest Bullseye image on a SD for my A64 Olimex w/ eMMC and I'm having trouble running the image from the eMMC.

I have copied back the original "olinuxino-sd-to-emmc" scripts onto the SD card and except that I had to regenerate a /etc/fstab file so it mentions UUIDs, the process works without errors.

Unfortunately when trying to boot from the eMMC, first nothing comes out on the HDMI port (but that may be unrelated), but most importantly, if I use the serial connection to the board (so I can see the boot messages), it seems to load some kind of limited kernel in a ramfs ... I don't know where this comes from really ... I don't even have to log in and only a limited set of linux commands is available ...

I suppose I should modify/regenerate stuff in /boot/boot.cmd (or .scr) but I'm not sure where to begin ...

Could you please help ? Thanks !

Here are the boot messages if it helps ...

` U-Boot SPL 2021.04+olimex-1-20210821.121541 (Aug 21 2021 - 12:16:49 +0000) DRAM: 1024 MiB Trying to boot from MMC2 NOTICE: BL31: v2.0(debug): NOTICE: BL31: Built : 23:33:29, Nov 27 2018 NOTICE: BL31: Detected Allwinner A64/H64/R18 SoC (1689) NOTICE: BL31: Found U-Boot DTB at 0x40b1870, model: Olimex A64-Olinuxino-eMMC INFO: ARM GICv2 driver initialized INFO: Configuring SPC Controller NOTICE: BL31: PMIC: Detected AXP803 on RSB. INFO: PMIC: AXP803: Enabling DRIVEVBUS INFO: BL31: Platform setup done INFO: BL31: Initializing runtime services INFO: BL31: cortex_a53: CPU workaround for 843419 was applied INFO: BL31: cortex_a53: CPU workaround for 855873 was applied INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x4a000000 INFO: SPSR = 0x3c9

U-Boot 2021.04+olimex-1-20210821.121541 (Aug 21 2021 - 12:16:49 +0000) Allwinner Technology

CPU: Allwinner A64 (SUN50I) Model: Olimex A64-Olinuxino-eMMC DRAM: 1 GiB MMC: mmc@1c0f000: 0, mmc@1c11000: 1 Loading Environment from EXT4... MMC: no card present Warning: HDMI PHY init timeout! Warning: HDMI PHY init timeout! Warning: HDMI PHY init timeout! Warning: HDMI PHY init timeout! In: serial Out: serial Err: serial Allwinner mUSB OTG (Peripheral) Net: phy interface7 eth0: ethernet@1c30000, eth1: usb_ether starting USB... Bus usb@1c1a000: USB EHCI 1.00 Bus usb@1c1a400: USB OHCI 1.0 Bus usb@1c1b000: USB EHCI 1.00 Bus usb@1c1b400: USB OHCI 1.0 scanning bus usb@1c1a000 for devices... 1 USB Device(s) found scanning bus usb@1c1a400 for devices... 1 USB Device(s) found scanning bus usb@1c1b000 for devices... EHCI timed out on TD - token=0x80008d80

  USB device not accepting new address (error=80000000)

3 USB Device(s) found scanning bus usb@1c1b400 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Hit any key to stop autoboot: 0 switch to partitions #0, OK mmc1(part 0) is current device Scanning mmc 1:2... Found U-Boot script /boot/boot.scr 993 bytes read in 2 ms (484.4 KiB/s)

Executing script at 4fc00000

27533184 bytes read in 1180 ms (22.3 MiB/s) 26251811 bytes read in 1126 ms (22.2 MiB/s) 28321 bytes read in 5 ms (5.4 MiB/s) Moving Image from 0x40080000 to 0x40200000, end=41ce0000

Loading init Ramdisk from Legacy Image at 4fe00000 ...

Image Name: Image Type: AArch64 Linux RAMDisk Image (uncompressed) Data Size: 26251747 Bytes = 25 MiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK

Flattened Device Tree blob at 4fa00000

Booting using the fdt blob at 0x4fa00000 Loading Ramdisk to 486f6000, end 49fff1e3 ... OK Loading Device Tree to 00000000486ec000, end 00000000486f5ea0 ... OK

Starting kernel ...

[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 5.10.0-9-arm64 (debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-6) 10.2.1 20210110, GNU ld (GNU Binutils for Debian) 2.35.2) #1 SMP Debian 5.10.70-1 (2021-09-30) [ 0.000000] Machine model: Olimex A64-Olinuxino [ 0.000000] efi: UEFI not found. [ 0.000000] NUMA: No NUMA configuration found [ 0.000000] NUMA: Faking a node at [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] NUMA: NODE_DATA [mem 0x7fddab00-0x7fddcfff] [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff] [ 0.000000] cma: Reserved 64 MiB at 0x000000007a000000 [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.1 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.1 [ 0.000000] percpu: Embedded 33 pages/cpu s95384 r8192 d31592 u135168 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: detected: ARM erratum 845719 [ 0.000000] CPU features: detected: ARM erratum 843419 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 258048 [ 0.000000] Policy zone: DMA [ 0.000000] Kernel command line: root=PARTUUID=51db4b8c-02 rw rootwait [ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off [ 0.000000] Memory: 909188K/1048576K available (11840K kernel code, 2438K rwdata, 7020K rodata, 5440K init, 596K bss, 73852K reserved, 65536K cma-reserved) [ 0.000000] random: get_random_u64 called from __kmem_cache_create+0x38/0x560 with crng_init=0 [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] ftrace: allocating 38562 entries in 151 pages [ 0.000000] ftrace: allocated 151 pages with 5 groups [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. [ 0.000000] Rude variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] GIC: Using split EOI/Deactivate mode [ 0.000000] arch_timer: Enabling global workaround for Allwinner erratum UNKNOWN1 [ 0.000000] arch_timer: CPU0: Trapping CNTVCT access [ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns [ 0.000006] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns [ 0.000808] Console: colour dummy device 80x25 [ 0.001253] printk: console [tty0] enabled [ 0.001393] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000) [ 0.001423] pid_max: default: 32768 minimum: 301 [ 0.001604] LSM: Security Framework initializing [ 0.001647] Yama: disabled by default; enable with sysctl kernel.yama.* [ 0.001798] AppArmor: AppArmor initialized [ 0.001817] TOMOYO Linux initialized [ 0.001913] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.001942] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.004428] rcu: Hierarchical SRCU implementation. [ 0.006912] EFI services will not be available. [ 0.007436] smp: Bringing up secondary CPUs ... [ 0.009108] Detected VIPT I-cache on CPU1 [ 0.009169] arch_timer: CPU1: Trapping CNTVCT access [ 0.009193] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.010451] Detected VIPT I-cache on CPU2 [ 0.010486] arch_timer: CPU2: Trapping CNTVCT access [ 0.010500] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.011687] Detected VIPT I-cache on CPU3 [ 0.011718] arch_timer: CPU3: Trapping CNTVCT access [ 0.011731] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.011835] smp: Brought up 1 node, 4 CPUs [ 0.011934] SMP: Total of 4 processors activated. [ 0.011949] CPU features: detected: 32-bit EL0 Support [ 0.012008] CPU features: detected: CRC32 instructions [ 0.012026] CPU features: detected: 32-bit EL1 Support [ 0.024564] CPU: All CPU(s) started at EL2 [ 0.024638] alternatives: patching kernel code [ 0.026687] devtmpfs: initialized [ 0.034755] Registered cp15_barrier emulation handler [ 0.034798] Registered setend emulation handler [ 0.034819] KASLR disabled due to lack of seed [ 0.035077] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.035135] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.037920] pinctrl core: initialized pinctrl subsystem [ 0.038906] DMI not present or invalid. [ 0.039580] NET: Registered protocol family 16 [ 0.041766] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations [ 0.041938] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.042138] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.042218] audit: initializing netlink subsys (disabled) [ 0.042426] audit: type=2000 audit(0.040:1): state=initialized audit_enabled=0 res=1 [ 0.043832] thermal_sys: Registered thermal governor 'fair_share' [ 0.043838] thermal_sys: Registered thermal governor 'bang_bang' [ 0.043856] thermal_sys: Registered thermal governor 'step_wise' [ 0.043871] thermal_sys: Registered thermal governor 'user_space' [ 0.043885] thermal_sys: Registered thermal governor 'power_allocator' [ 0.044408] cpuidle: using governor ladder [ 0.044455] cpuidle: using governor menu [ 0.044589] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. [ 0.044732] ASID allocator initialised with 65536 entries [ 0.045269] Serial: AMBA PL011 UART driver [ 0.072022] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.072060] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages [ 0.072077] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.072093] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages [ 0.893199] ACPI: Interpreter disabled. [ 0.893545] iommu: Default domain type: Translated [ 0.893855] vgaarb: loaded [ 0.894294] EDAC MC: Ver: 3.0.0 [ 0.896060] NetLabel: Initializing [ 0.896081] NetLabel: domain hash size = 128 [ 0.896093] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO [ 0.896190] NetLabel: unlabeled traffic allowed by default [ 0.896538] clocksource: Switched to clocksource arch_sys_counter [ 0.982374] VFS: Disk quotas dquot_6.6.0 [ 0.982479] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.983375] AppArmor: AppArmor Filesystem Enabled [ 0.983643] pnp: PnP ACPI: disabled [ 0.993076] NET: Registered protocol family 2 [ 0.993262] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.994374] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear) [ 0.994446] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.994660] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear) [ 0.994822] TCP: Hash tables configured (established 8192 bind 8192) [ 0.995003] UDP hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.995058] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear) [ 0.995293] NET: Registered protocol family 1 [ 0.995334] NET: Registered protocol family 44 [ 0.995358] PCI: CLS 0 bytes, default 64 [ 0.995717] Trying to unpack rootfs image as initramfs... [ 2.700872] Freeing initrd memory: 25636K [ 2.701965] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available [ 2.702413] kvm [1]: IPA Size Limit: 40 bits [ 2.704244] kvm [1]: vgic interrupt IRQ9 [ 2.704439] kvm [1]: Hyp mode initialized successfully [ 2.706323] Initialise system trusted keyrings [ 2.706393] Key type blacklist registered [ 2.706659] workingset: timestamp_bits=42 max_order=18 bucket_order=0 [ 2.714026] zbud: loaded [ 2.714982] integrity: Platform Keyring initialized [ 2.715009] Key type asymmetric registered [ 2.715024] Asymmetric key parser 'x509' registered [ 2.715077] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 2.715363] io scheduler mq-deadline registered [ 2.716891] sun50i-de2-bus 1000000.bus: Error couldn't map SRAM to device [ 2.722751] sun50i-a64-r-pinctrl 1f02c00.pinctrl: initialized sunXi PIO driver [ 2.724073] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 2.736096] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.738539] Serial: AMBA driver [ 2.739018] msm_serial: driver initialized [ 2.741637] mousedev: PS/2 mouse device common for all mice [ 2.742962] sun6i-rtc 1f00000.rtc: registered as rtc0 [ 2.743011] sun6i-rtc 1f00000.rtc: setting system clock to 1970-01-02T15:46:14 UTC (143174) [ 2.743031] sun6i-rtc 1f00000.rtc: RTC enabled [ 2.744254] sun50i-a64-r-pinctrl 1f02c00.pinctrl: supply vcc-pl not found, using dummy regulator [ 2.744981] ledtrig-cpu: registered to indicate activity on CPUs [ 2.747262] NET: Registered protocol family 10 [ 2.792362] Segment Routing with IPv6 [ 2.792491] mip6: Mobile IPv6 [ 2.792511] NET: Registered protocol family 17 [ 2.792726] mpls_gso: MPLS GSO support [ 2.793216] registered taskstats version 1 [ 2.793241] Loading compiled-in X.509 certificates [ 2.980201] Loaded X.509 cert 'Debian Secure Boot CA: 6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1' [ 2.980303] Loaded X.509 cert 'Debian Secure Boot Signer 2021 - linux: 4b6ef5abca669825178e052c84667ccbc0531f8c' [ 2.980478] zswap: loaded using pool lzo/zbud [ 2.981038] Key type ._fscrypt registered [ 2.981056] Key type .fscrypt registered [ 2.981069] Key type fscrypt-provisioning registered [ 2.981284] AppArmor: AppArmor sha1 policy hashing enabled [ 3.001166] sunxi-rsb 1f03400.rsb: RSB running at 3000000 Hz [ 3.006293] sun50i-a64-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver [ 3.007113] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PB regulator [ 3.007139] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 40 [ 3.007157] sun50i-a64-pinctrl 1c20800.pinctrl: pin-40 (1c28000.serial) status -517 [ 3.007178] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 40 (PB8) from group PB8 on device 1c20800.pinctrl [ 3.007200] dw-apb-uart 1c28000.serial: Error applying setting, reverse things back [ 3.007917] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PB regulator [ 3.007942] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 40 [ 3.007960] sun50i-a64-pinctrl 1c20800.pinctrl: pin-40 (1c28000.serial) status -517 [ 3.007980] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 40 (PB8) from group PB8 on device 1c20800.pinctrl [ 3.008002] dw-apb-uart 1c28000.serial: Error applying setting, reverse things back [ 3.016996] Freeing unused kernel memory: 5440K [ 3.047651] Checked W+X mappings: passed, no W+X pages found [ 3.047717] Run /init as init process [ 3.399482] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PF regulator [ 3.399534] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 160 [ 3.399553] sun50i-a64-pinctrl 1c20800.pinctrl: pin-160 (1c0f000.mmc) status -517 [ 3.399575] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 160 (PF0) from group PF0 on device 1c20800.pinctrl [ 3.399596] sunxi-mmc 1c0f000.mmc: Error applying setting, reverse things back [ 3.413072] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.413114] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 192 [ 3.413133] sun50i-a64-pinctrl 1c20800.pinctrl: pin-192 (1c10000.mmc) status -517 [ 3.413154] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 192 (PG0) from group PG0 on device 1c20800.pinctrl [ 3.413176] sunxi-mmc 1c10000.mmc: Error applying setting, reverse things back [ 3.502657] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 3.502701] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 233 [ 3.502720] sun50i-a64-pinctrl 1c20800.pinctrl: pin-233 (1c20800.pinctrl:233) status -517 [ 3.502741] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 3.575456] usbcore: registered new interface driver usbfs [ 3.575549] usbcore: registered new interface driver hub [ 3.575633] usbcore: registered new device driver usb [ 3.589379] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.602045] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.605596] ohci-platform: OHCI generic platform driver [ 3.630977] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PB regulator [ 3.631021] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 40 [ 3.631039] sun50i-a64-pinctrl 1c20800.pinctrl: pin-40 (1c28000.serial) status -517 [ 3.631060] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 40 (PB8) from group PB8 on device 1c20800.pinctrl [ 3.631083] dw-apb-uart 1c28000.serial: Error applying setting, reverse things back [ 3.633246] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PF regulator [ 3.633307] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 160 [ 3.633325] sun50i-a64-pinctrl 1c20800.pinctrl: pin-160 (1c0f000.mmc) status -517 [ 3.633348] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 160 (PF0) from group PF0 on device 1c20800.pinctrl [ 3.633371] sunxi-mmc 1c0f000.mmc: Error applying setting, reverse things back [ 3.633937] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 3.633968] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 233 [ 3.633987] sun50i-a64-pinctrl 1c20800.pinctrl: pin-233 (1c20800.pinctrl:233) status -517 [ 3.634009] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 3.634215] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.634238] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 192 [ 3.634257] sun50i-a64-pinctrl 1c20800.pinctrl: pin-192 (1c10000.mmc) status -517 [ 3.634277] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 192 (PG0) from group PG0 on device 1c20800.pinctrl [ 3.634299] sunxi-mmc 1c10000.mmc: Error applying setting, reverse things back [ 3.636333] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PB regulator [ 3.636372] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 40 [ 3.636391] sun50i-a64-pinctrl 1c20800.pinctrl: pin-40 (1c28000.serial) status -517 [ 3.636412] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 40 (PB8) from group PB8 on device 1c20800.pinctrl [ 3.636434] dw-apb-uart 1c28000.serial: Error applying setting, reverse things back [ 3.637478] ehci-platform: EHCI generic platform driver [ 3.637942] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PF regulator [ 3.637968] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 160 [ 3.637986] sun50i-a64-pinctrl 1c20800.pinctrl: pin-160 (1c0f000.mmc) status -517 [ 3.638007] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 160 (PF0) from group PF0 on device 1c20800.pinctrl [ 3.638029] sunxi-mmc 1c0f000.mmc: Error applying setting, reverse things back [ 3.638805] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 3.638839] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 233 [ 3.638857] sun50i-a64-pinctrl 1c20800.pinctrl: pin-233 (1c20800.pinctrl:233) status -517 [ 3.638879] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 3.640210] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.640244] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 192 [ 3.640262] sun50i-a64-pinctrl 1c20800.pinctrl: pin-192 (1c10000.mmc) status -517 [ 3.640284] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 192 (PG0) from group PG0 on device 1c20800.pinctrl [ 3.640305] sunxi-mmc 1c10000.mmc: Error applying setting, reverse things back [ 3.662952] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PB regulator [ 3.662997] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 40 [ 3.663017] sun50i-a64-pinctrl 1c20800.pinctrl: pin-40 (1c28000.serial) status -517 [ 3.663039] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 40 (PB8) from group PB8 on device 1c20800.pinctrl [ 3.663061] dw-apb-uart 1c28000.serial: Error applying setting, reverse things back [ 3.666054] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PF regulator [ 3.666097] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 160 [ 3.666116] sun50i-a64-pinctrl 1c20800.pinctrl: pin-160 (1c0f000.mmc) status -517 [ 3.666137] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 160 (PF0) from group PF0 on device 1c20800.pinctrl [ 3.666159] sunxi-mmc 1c0f000.mmc: Error applying setting, reverse things back [ 3.668145] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 3.668191] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 233 [ 3.668210] sun50i-a64-pinctrl 1c20800.pinctrl: pin-233 (1c20800.pinctrl:233) status -517 [ 3.668232] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 3.669895] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.669935] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 192 [ 3.669953] sun50i-a64-pinctrl 1c20800.pinctrl: pin-192 (1c10000.mmc) status -517 [ 3.669974] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 192 (PG0) from group PG0 on device 1c20800.pinctrl [ 3.669996] sunxi-mmc 1c10000.mmc: Error applying setting, reverse things back [ 3.671762] pps_core: LinuxPPS API ver. 1 registered [ 3.671794] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 3.676425] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PB regulator [ 3.676468] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 40 [ 3.676487] sun50i-a64-pinctrl 1c20800.pinctrl: pin-40 (1c28000.serial) status -517 [ 3.676508] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 40 (PB8) from group PB8 on device 1c20800.pinctrl [ 3.676584] dw-apb-uart 1c28000.serial: Error applying setting, reverse things back [ 3.682462] PTP clock support registered [ 3.706781] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.706823] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 201 [ 3.706843] sun50i-a64-pinctrl 1c20800.pinctrl: pin-201 (1c20800.pinctrl:201) status -517 [ 3.711460] axp20x-rsb sunxi-rsb-3a3: AXP20x variant AXP803 found [ 3.713605] libphy: Fixed MDIO Bus: probed [ 3.723822] axp20x-rsb sunxi-rsb-3a3: AXP20X driver loaded [ 3.726138] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PF regulator [ 3.726184] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 160 [ 3.726203] sun50i-a64-pinctrl 1c20800.pinctrl: pin-160 (1c0f000.mmc) status -517 [ 3.726224] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 160 (PF0) from group PF0 on device 1c20800.pinctrl [ 3.726246] sunxi-mmc 1c0f000.mmc: Error applying setting, reverse things back [ 3.726606] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PH regulator [ 3.726636] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 233 [ 3.726654] sun50i-a64-pinctrl 1c20800.pinctrl: pin-233 (1c20800.pinctrl:233) status -517 [ 3.726676] sun4i-usb-phy 1c19400.phy: Couldn't request ID GPIO [ 3.729667] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.729711] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 192 [ 3.729729] sun50i-a64-pinctrl 1c20800.pinctrl: pin-192 (1c10000.mmc) status -517 [ 3.729752] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 192 (PG0) from group PG0 on device 1c20800.pinctrl [ 3.729774] sunxi-mmc 1c10000.mmc: Error applying setting, reverse things back [ 3.732644] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PB regulator [ 3.732687] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 40 [ 3.732705] sun50i-a64-pinctrl 1c20800.pinctrl: pin-40 (1c28000.serial) status -517 [ 3.732726] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 40 (PB8) from group PB8 on device 1c20800.pinctrl [ 3.732748] dw-apb-uart 1c28000.serial: Error applying setting, reverse things back [ 3.735291] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.735336] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 201 [ 3.735355] sun50i-a64-pinctrl 1c20800.pinctrl: pin-201 (1c20800.pinctrl:201) status -517 [ 3.772804] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PD regulator [ 3.772850] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 104 [ 3.772869] sun50i-a64-pinctrl 1c20800.pinctrl: pin-104 (1c30000.ethernet) status -517 [ 3.772892] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 104 (PD8) from group PD8 on device 1c20800.pinctrl [ 3.772915] dwmac-sun8i 1c30000.ethernet: Error applying setting, reverse things back [ 3.799225] axp20x-gpio axp20x-gpio: DMA mask not set [ 3.799463] vcc-3v3: supplied by regulator-dummy [ 3.799884] axp20x-gpio axp20x-gpio: AXP209 pinctrl and GPIO driver loaded [ 3.800196] vdd-cpux: supplied by regulator-dummy [ 3.801193] dcdc4: supplied by regulator-dummy [ 3.801483] vcc-ddr3: supplied by regulator-dummy [ 3.802366] vdd-sys: supplied by regulator-dummy [ 3.803234] dc1sw: supplied by regulator-dummy [ 3.803270] sun4i-usb-phy 1c19400.phy: Couldn't get regulator usb0_vbus... Deferring probe [ 3.803773] vcc-pe: supplied by regulator-dummy [ 3.804287] sunxi-mmc 1c0f000.mmc: Got CD GPIO [ 3.804707] vcc-pl: supplied by regulator-dummy [ 3.806548] vcc-pll-avcc: supplied by regulator-dummy [ 3.807017] sun50i-a64-pinctrl 1c20800.pinctrl: Couldn't get bank PG regulator [ 3.807059] sun50i-a64-pinctrl 1c20800.pinctrl: request() failed for pin 192 [ 3.807077] sun50i-a64-pinctrl 1c20800.pinctrl: pin-192 (1c10000.mmc) status -517 [ 3.807099] sun50i-a64-pinctrl 1c20800.pinctrl: could not request pin 192 (PG0) from group PG0 on device 1c20800.pinctrl [ 3.807122] sunxi-mmc 1c10000.mmc: Error applying setting, reverse things back [ 3.807844] vcc-hdmi: supplied by regulator-dummy [ 3.808458] vcc-mipi: supplied by regulator-dummy [ 3.809167] vcc-avdd-csi: supplied by regulator-dummy [ 3.809839] vcc-wifi-io: supplied by regulator-dummy [ 3.810440] cpvdd: supplied by regulator-dummy [ 3.811028] vcc-dvdd-csi: supplied by regulator-dummy [ 3.811512] eldo3: supplied by regulator-dummy [ 3.811937] vcc-1v2-hsic: supplied by regulator-dummy [ 3.812142] vdd-cpus: supplied by regulator-dummy [ 3.812684] vcc-rtc: supplied by regulator-dummy [ 3.813196] ldo-io0: supplied by regulator-dummy [ 3.813632] ldo-io1: supplied by regulator-dummy [ 3.813980] usb0-vbus: supplied by regulator-dummy [ 3.828631] sunxi-mmc 1c0f000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 3.830398] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 36, base_baud = 1500000) is a U6_16550A [ 5.975794] printk: console [ttyS0] enabled [ 5.981268] dwmac-sun8i 1c30000.ethernet: IRQ eth_wake_irq not found [ 5.987721] dwmac-sun8i 1c30000.ethernet: IRQ eth_lpi not found [ 5.988211] dwmac-sun8i 1c30000.ethernet: PTP uses main clock [ 5.999497] dwmac-sun8i 1c30000.ethernet: Current syscon value is not the default 1806 (expect 0) [ 6.008816] dwmac-sun8i 1c30000.ethernet: No HW DMA feature register supported [ 6.016117] dwmac-sun8i 1c30000.ethernet: RX Checksum Offload Engine supported [ 6.023420] dwmac-sun8i 1c30000.ethernet: COE Type 2 [ 6.028457] dwmac-sun8i 1c30000.ethernet: TX Checksum insertion supported [ 6.028474] dwmac-sun8i 1c30000.ethernet: Normal descriptors [ 6.040943] dwmac-sun8i 1c30000.ethernet: Chain mode enabled [ 6.042057] libphy: stmmac: probed [ 6.076432] phy phy-1c19400.phy.0: Changing dr_mode to 1 [ 6.082003] ohci-platform 1c1a400.usb: Generic Platform OHCI controller [ 6.088824] ohci-platform 1c1a400.usb: new USB bus registered, assigned bus number 1 [ 6.096747] ohci-platform 1c1a400.usb: irq 29, io mem 0x01c1a400 [ 6.164769] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10 [ 6.173053] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.180289] usb usb1: Product: Generic Platform OHCI controller [ 6.186219] usb usb1: Manufacturer: Linux 5.10.0-9-arm64 ohci_hcd [ 6.192321] usb usb1: SerialNumber: 1c1a400.usb [ 6.197614] hub 1-0:1.0: USB hub found [ 6.201460] hub 1-0:1.0: 1 port detected [ 6.207360] ohci-platform 1c1b400.usb: Generic Platform OHCI controller [ 6.214103] ohci-platform 1c1b400.usb: new USB bus registered, assigned bus number 2 [ 6.222057] ohci-platform 1c1b400.usb: irq 31, io mem 0x01c1b400 [ 6.288765] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10 [ 6.297050] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.304285] usb usb2: Product: Generic Platform OHCI controller [ 6.310216] usb usb2: Manufacturer: Linux 5.10.0-9-arm64 ohci_hcd [ 6.316319] usb usb2: SerialNumber: 1c1b400.usb [ 6.321596] hub 2-0:1.0: USB hub found [ 6.325431] hub 2-0:1.0: 1 port detected [ 6.332614] usb_phy_generic usb_phy_generic.1.auto: supply vcc not found, using dummy regulator [ 6.334531] sunxi-mmc 1c10000.mmc: allocated mmc-pwrseq [ 6.344945] musb-hdrc musb-hdrc.2.auto: MUSB HDRC host driver [ 6.352483] musb-hdrc musb-hdrc.2.auto: new USB bus registered, assigned bus number 3 [ 6.360609] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 6.368898] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.372146] sunxi-mmc 1c10000.mmc: initialized, max. request size: 16384 KB, uses new timings mode [ 6.376136] usb usb3: Product: MUSB HDRC host driver [ 6.390097] usb usb3: Manufacturer: Linux 5.10.0-9-arm64 musb-hcd [ 6.396212] usb usb3: SerialNumber: musb-hdrc.2.auto [ 6.401939] hub 3-0:1.0: USB hub found [ 6.402978] mmc1: new high speed SDIO card at address 0001 [ 6.405815] hub 3-0:1.0: 1 port detected [ 6.430605] ehci-platform 1c1a000.usb: EHCI Host Controller [ 6.436276] ehci-platform 1c1a000.usb: new USB bus registered, assigned bus number 4 [ 6.444219] ehci-platform 1c1a000.usb: irq 28, io mem 0x01c1a000 [ 6.464565] ehci-platform 1c1a000.usb: USB 2.0 started, EHCI 1.00 [ 6.470960] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 6.479245] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.486479] usb usb4: Product: EHCI Host Controller [ 6.491377] usb usb4: Manufacturer: Linux 5.10.0-9-arm64 ehci_hcd [ 6.497484] usb usb4: SerialNumber: 1c1a000.usb [ 6.502749] hub 4-0:1.0: USB hub found [ 6.506594] hub 4-0:1.0: 1 port detected [ 6.512474] ehci-platform 1c1b000.usb: EHCI Host Controller [ 6.518162] ehci-platform 1c1b000.usb: new USB bus registered, assigned bus number 5 [ 6.526212] ehci-platform 1c1b000.usb: irq 30, io mem 0x01c1b000 [ 6.652562] usb 2-1: new full-speed USB device number 2 using ohci-platform [ 6.672563] ehci-platform 1c1b000.usb: USB 2.0 started, EHCI 1.00 [ 6.678998] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10 [ 6.687283] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 6.694518] usb usb5: Product: EHCI Host Controller [ 6.699411] usb usb5: Manufacturer: Linux 5.10.0-9-arm64 ehci_hcd [ 6.705514] usb usb5: SerialNumber: 1c1b000.usb [ 6.710794] hub 5-0:1.0: USB hub found [ 6.714630] hub 5-0:1.0: 1 port detected [ 6.972563] usb 5-1: new high-speed USB device number 2 using ehci-platform [ 7.137188] usb 5-1: New USB device found, idVendor=1a40, idProduct=0101, bcdDevice= 1.11 [ 7.145410] usb 5-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 7.152562] usb 5-1: Product: USB 2.0 Hub [ 7.157521] hub 5-1:1.0: USB hub found [ 7.161436] hub 5-1:1.0: 4 ports detected [ 7.269280] random: fast init done [ 7.576556] usb 5-1.1: new full-speed USB device number 3 using ehci-platform [ 7.821044] usb 5-1.1: New USB device found, idVendor=0a12, idProduct=1004, bcdDevice=34.49 [ 7.829414] usb 5-1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 7.836736] usb 5-1.1: Product: Avantree DG80 [ 7.866583] hid: raw HID events driver (C) Jiri Kosina [ 7.887265] usbcore: registered new interface driver usbhid [ 7.892920] usbhid: USB HID core driver [ 7.905572] input: Avantree DG80 Consumer Control as /devices/platform/soc/1c1b000.usb/usb5/5-1/5-1.1/5-1.1:1.3/0003:0A12:1004.0001/input/input0 [ 7.976790] input: Avantree DG80 as /devices/platform/soc/1c1b000.usb/usb5/5-1/5-1.1/5-1.1:1.3/0003:0A12:1004.0001/input/input1 [ 7.988855] hid-generic 0003:0A12:1004.0001: input,hiddev0,hidraw0: USB HID v1.11 Device [Avantree DG80] on usb-1c1b000.usb-1.1/input3 [ 8.040578] usb 5-1.3: new low-speed USB device number 4 using ehci-platform [ 8.288064] usb 5-1.3: New USB device found, idVendor=045e, idProduct=0750, bcdDevice= 1.10 [ 8.296460] usb 5-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 8.303782] usb 5-1.3: Product: Wired Keyboard 600 [ 8.308585] usb 5-1.3: Manufacturer: Microsoft [ 8.341567] input: Microsoft Wired Keyboard 600 as /devices/platform/soc/1c1b000.usb/usb5/5-1/5-1.3/5-1.3:1.0/0003:045E:0750.0002/input/input2 [ 8.413194] microsoft 0003:045E:0750.0002: input,hidraw1: USB HID v1.11 Keyboard [Microsoft Wired Keyboard 600] on usb-1c1b000.usb-1.3/input0 [ 8.428112] input: Microsoft Wired Keyboard 600 as /devices/platform/soc/1c1b000.usb/usb5/5-1/5-1.3/5-1.3:1.1/0003:045E:0750.0003/input/input3 [ 8.500791] microsoft 0003:045E:0750.0003: input,hidraw2: USB HID v1.11 Device [Microsoft Wired Keyboard 600] on usb-1c1b000.usb-1.3/input1 `

johang / sd-card-images