vc_dispmanx_display_open failed

I'm using a raspberry pi zero 1 w with Raspberry Pi OS Lite (released 2023-05-03). I'm trying to use an 1.3 inch LCD HAT from waveshare (documentation: https://www.waveshare.com/wiki/1.3inch_LCD_HAT). They forked this repo (https://files.waveshare.com/upload/b/bd/1.3inch_LCD_HAT_code.7z) and added some displays.

The cmake options are: cmake -DSPI_BUS_CLOCK_DIVISOR=20 -DWAVESHARE_1INCH3_LCD_HAT=ON -DBACKLIGHT_CONTROL=ON -DSTATISTICS=0 ..

pi@raspberrypi:~/waveshare_fbcp/build $ sudo ./fbcp
bcm_host_get_peripheral_address: 0x20000000, bcm_host_get_peripheral_size: 33554432, bcm_host_get_sdram_address: 0x40000000
BCM core speed: current: 250000000hz, max turbo: 400000000hz. SPI CDIV: 20, SPI max frequency: 20000000hz
Allocated DMA channel 7
Allocated DMA channel 1
Enabling DMA channels Tx:7 and Rx:1
DMA hardware register file is at ptr: 0xb4ba2000, using DMA TX channel: 7 and DMA RX channel: 1
DMA hardware TX channel register file is at ptr: 0xb4ba2700, DMA RX channel register file is at ptr: 0xb4ba2100
Resetting DMA channels for use
DMA all set up
Initializing display
Resetting display at reset GPIO pin 27
Setting TFT backlight on at pin 24
InitSPI done
vc_dispmanx_display_open failed! Make sure to have hdmi_force_hotplug=1 setting in /boot/config.txt

/boot/config.txt

# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details

# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1

# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16

# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720

# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1

# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1

# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2

# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4

# uncomment for composite PAL
#sdtv_mode=2

#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800

# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on # disabled for https://github.com/juj/fbcp-ili9341

# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18

# Additional overlays and parameters are documented /boot/overlays/README

# Enable audio (loads snd_bcm2835)
dtparam=audio=on

# Automatically load overlays for detected cameras
camera_auto_detect=1

# Automatically load overlays for detected DSI displays
display_auto_detect=1

# Enable DRM VC4 V3D driver
#dtoverlay=vc4-kms-v3d # disabled for https://github.com/juj/fbcp-ili9341
max_framebuffers=2

# Disable compensation for displays with overscan
disable_overscan=1

[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1

[all]

[pi4]
# Run as fast as firmware / board allows
arm_boost=1

[all]

gpio=6,19,5,26,13,21,20,16=pu

hdmi_force_hotplug=1
hdmi_cvt=300 300 60 1 0 0 0
hdmi_group=2
hdmi_mode=87
display_rotate=0

juj / fbcp-ili9341

vc_dispmanx_display_open failed #309