jurobystricky / Netgear-A6210

AC1200 High Gain WiFi USB Adapter Linux kernel driver
291 stars 153 forks source link

hostapd: nl80211 driver initialization failed #134

Open cagnulein opened 4 years ago

cagnulein commented 4 years ago

Did anyone try to use this adapter with hostapd? I've got always a nl80211 driver initialization failed

This is my hostapd configuration (works fine with the wlan0, the builtin wifi on the raspberry 4)

interface=wlan1
driver=nl80211

hw_mode=g
channel=11
ieee80211n=1
wmm_enabled=1
#ht_capab=[HT40][SHORT-GI-20][DSSS_CCK-40]
ht_capab=[HT40][SHORT-GI-20]
macaddr_acl=0
ignore_broadcast_ssid=0

# Use WPA2
#auth_algs=1
#wpa=1
#wpa_key_mgmt=WPA-PSK
#rsn_pairwise=CCMP

# Change these to your choice
# This is the name of the network
ssid=Pi3-AP
# The network passphrase
#wpa_passphrase=raspberry

ctrl_interface=/var/run/hostapd
ctrl_interface_group=0
cagnulein commented 4 years ago
nl80211: Could not configure driver mode
nl80211: deinit ifname=wlan1 disabled_11b_rates=0
nl80211 driver initialization failed.
wlan1: interface state UNINITIALIZED->DISABLED
wlan1: AP-DISABLED
wlan1: CTRL-EVENT-TERMINATING
hostapd_free_hapd_data: Interface wlan1 wasn't started
root@raspberrypi:/home/pi# hostapd -dd /etc/hostapd/hostapd.conf
random: getrandom() support available
Configuration file: /etc/hostapd/hostapd.conf
ctrl_interface_group=0
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supported cipher 00-0f-ac:13
nl80211: Supported cipher 00-0f-ac:11
nl80211: Supported cipher 00-0f-ac:12
nl80211: Using driver-based off-channel TX
nl80211: Driver-advertised extended capabilities (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Driver-advertised extended capabilities mask (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: interface wlan1 in phy phy0
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Failed to set interface 4 to mode 3: -95 (Operation not supported)
nl80211: Try mode change after setting interface down
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Failed to set interface 4 to mode 3: -95 (Operation not supported)
nl80211: Interface mode change to 3 from 0 failed
nl80211: Could not configure driver mode
nl80211: deinit ifname=wlan1 disabled_11b_rates=0
nl80211: Remove monitor interface: refcount=0
netlink: Operstate: ifindex=4 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)
nl80211: Set mode ifindex 4 iftype 2 (STATION)
nl80211 driver initialization failed.
hostapd_interface_deinit_free(0x1e47020)
hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1
hostapd_interface_deinit(0x1e47020)
wlan1: interface state UNINITIALIZED->DISABLED
hostapd_bss_deinit: deinit bss wlan1
wlan1: AP-DISABLED
hostapd_cleanup(hapd=0x1e49748 (wlan1))
wlan1: CTRL-EVENT-TERMINATING
hostapd_free_hapd_data: Interface wlan1 wasn't started
hostapd_interface_deinit_free: driver=(nil) drv_priv=(nil) -> hapd_deinit
hostapd_interface_free(0x1e47020)
hostapd_interface_free: free hapd 0x1e49748
hostapd_cleanup_iface(0x1e47020)
hostapd_cleanup_iface_partial(0x1e47020)
hostapd_cleanup_iface: free iface=0x1e47020
Rootshikhar commented 3 years ago

bruh i m also facing this issue have you solved it ??