kampfschrei / reaver-wps

Automatically exported from code.google.com/p/reaver-wps
0 stars 0 forks source link

Hang on "Receive timeout occurred" #450

Open GoogleCodeExporter opened 8 years ago

GoogleCodeExporter commented 8 years ago
A few things to consider before submitting an issue:

0. We write documentation for a reason, if you have not read it and are
having problems with Reaver these pages are required reading before
submitting an issue:
http://code.google.com/p/reaver-wps/wiki/HintsAndTips
http://code.google.com/p/reaver-wps/wiki/README
http://code.google.com/p/reaver-wps/wiki/FAQ
http://code.google.com/p/reaver-wps/wiki/SupportedWirelessDrivers
1. Reaver will only work if your card is in monitor mode.  If you do not
know what monitor mode is then you should learn more about 802.11 hacking
in linux before using Reaver.
2. Using Reaver against access points you do not own or have permission to
attack is illegal.  If you cannot answer basic questions (i.e. model
number, distance away, etc) about the device you are attacking then do not
post your issue here.  We will not help you break the law.
3. Please look through issues that have already been posted and make sure
your question has not already been asked here: http://code.google.com/p
/reaver-wps/issues/list
4. Often times we need packet captures of mon0 while Reaver is running to
troubleshoot the issue (tcpdump -i mon0 -s0 -w broken_reaver.pcap).  Issue
reports with pcap files attached will receive more serious consideration.

Answer the following questions for every issue submitted:

0. What version of Reaver are you using?  (Only defects against the latest
version will be considered.)

1.4

1. What operating system are you using (Linux is the only supported OS)?
Backtrack 5r1

2. Is your wireless card in monitor mode (yes/no)?

Yes

3. What is the signal strength of the Access Point you are trying to crack?

about 80

4. What is the manufacturer and model # of the device you are trying to
crack?

5. What is the entire command line string you are supplying to reaver?

reaver -i mon0 -b 0C:71:5D:91:25:0D -vv -A -d 0 --dh-small -c 1 --auto

6. Please describe what you think the issue is.

I try the command line in three different AP but it gives the same error

7. Paste the output from Reaver below.

Reaver v1.4 WiFi Protected Setup Attack Tool
Copyright (c) 2011, Tactical Network Solutions, Craig Heffner 
<cheffner@tacnetsol.com>

[+] Switching mon0 to channel 1
[+] Waiting for beacon from 10:6F:3F:26:62:FF
[+] Associated with 10:6F:3F:26:62:FF (ESSID: Unkn0wn)
[+] Trying pin 12345670
[+] Sending EAPOL START request
[!] WARNING: Receive timeout occurred
[+] Sending EAPOL START request
[!] WARNING: Receive timeout occurred
[+] Sending EAPOL START request
[!] WARNING: Receive timeout occurred
[+] Sending EAPOL START request
[!] WARNING: Receive timeout occurred
[+] Sending EAPOL START request
[!] WARNING: Receive timeout occurred
[+] Sending EAPOL START request

Original issue reported on code.google.com by osuk...@gmail.com on 19 Dec 2012 at 6:27

GoogleCodeExporter commented 8 years ago
I found this same question is just repeat again and again but have no answer. 
Hope to see the answer is posted here. Thank you

Original comment by osuk...@gmail.com on 19 Dec 2012 at 6:29